OpenSUSE Network :: Huawei E1550 USB Modem In 11.2?

Mar 17, 2010

My machine is running on a dual-boot Windows Vista/openSUSE 11.2 scenario. I have been trying to get my Huawei E1550 to work on Linux for the past few days trying numerous methods suggested in other forums from people with the same problem, but I have not produced any fruitful results.

Plugging in the USB modem results in Linux detecting it as a CD-ROM. I have installed usb_modeswitch in attempt to switch it to a modem, but Linux still fails to recognize it. Windows Device Manager and lsusb both give ProductID=1001 and VendorID=12d1 connected to USB1. I'm guessing since Windows detects the correct IDs, the Linux versions should also be correct. In any case, I ran usb_modeswitch with the Default IDs for /etc/usb_modeswitch.conf, which gave 0x1446 as the ProductID, not 0x1001. Upon running usb_modeswitch, the product ID could not be found so the program fails and quits asking if it's connected (and it is).

Just to test, I also ran wvdial which unsurprisingly did not detect the modem and could not send the init strings. All commands were done using root privileges. Also note that when after usb_modeswitch is run and upon plugging in the USB, NetworkManager pops up near the tray saying "attached" but still shows the device as a CD-ROM.

View 5 Replies


ADVERTISEMENT

Ubuntu Networking :: E1550 Huawei Modem Configuration?

Mar 17, 2010

how configure E1550 Huawei modem in Ubuntu9.10.

View 1 Replies View Related

OpenSUSE Network :: 11.3 - Cannot Connect Huawei Modem (Keeps Failing)

Oct 5, 2010

I am trying to connect my huawei e160 usb modem but it keeps failing and does not show on the Network Manager, checking on /var/log/messages this it what I get:

Oct 5 15:31:30 LPKENBITD002 modem-manager: (ttyUSB1): re-checking support...
Oct 5 15:31:30 LPKENBITD002 modem-manager: (Huawei): (ttyUSB1) deferring support check
Oct 5 15:31:33 LPKENBITD002 modem-manager: (ttyUSB1): re-checking support...
Oct 5 15:31:33 LPKENBITD002 modem-manager: (Huawei): (ttyUSB1) deferring support check
Oct 5 15:31:36 LPKENBITD002 modem-manager: (ttyUSB1): re-checking support...
Oct 5 15:31:36 LPKENBITD002 modem-manager: (Huawei): (ttyUSB1) deferring support check

View 9 Replies View Related

OpenSUSE Network :: Can't Install Huawei E1752 Usb Modem

Jun 19, 2011

I am new to Linux and opensuse is lovely to me . However i have a problem, I dual boot windows and OpenSuse 10.3(because it plays mp3 out of the box) I actually tried newer versions but the problem is that I cant install this Huawei E1752 usb modem. I have failed people. Please help me. I need to use it for internet.

View 1 Replies View Related

OpenSUSE Network :: Can't Connect To Internet Huawei EC 325USB Modem / Fix It?

Jun 4, 2010

I tried to connect to the huawei cdma EC325 modem. using the network manager applet. System asked which tpe of connection i selected cdma and gave the username and password for the account and the password for my opensuse account.Still i cannot connect to the internet using huawei ec325 modem.How to rectify the problem What shall i do next.

View 2 Replies View Related

OpenSUSE Network :: Can Not Get USB Modem Huawei E220 To Connect To Internet / Sort It?

Aug 5, 2010

I can not get NetworkManager to handle my Huawei E220 usb modem. I have searched forums and tried a lot of things. I have just upgraded from openSUSE 11.2 to openSUSE 11.3 using zypper. It seems to work fine except that umtsmon stopped to work, so for now my laptop has no connetion to internet at all. Here are some information about my settings:

I have used usb_modeswitch to make the device a modem. Am I right if I say that usb_modeswitch is a one time command, or does it swap the setting each time it is called? Anyhow lsusb states that the device is a modem. (All the time.) code...

View 7 Replies View Related

OpenSUSE Network :: Huawei E220 HSDPA Modem Doesn't Read DNS With Knetworkmanager

Jul 9, 2010

I have a weird problem on my laptop. Everything works okey on PC though.

I'm using kNetworkManager on my OpenSuse 11.2 on PC.

Everything works fine there with the following settings:
1. Make a new GSM Connection in kNetworkManager and enter settings there
2. Edit etc/sysconfig/network/config file and set .....DNS_Policy from "auto" to ""
3. Enter openDNS to /etc/resolv.conf (nameserver xxx.xxx.xxx.xxx)

It works like that on my PC.

I did the same on my laptop. The modem connects fine, but the DNS'es ain't resolved. So skype etc will work, but no pages will open in Firefox for example.

What else should I need to do to make this work?

It's weird it works the SAME way on my PC, but doesn't on my laptop.

View 3 Replies View Related

OpenSUSE Hardware :: What Include Support A Driver For USB Modem Huawei E219 (HSDPA/UMTS) And Huawei EC226 (3G/EVDO)

Dec 23, 2009

What include support a driver for USB modem Huawei E219 (HSDPA/UMTS) and Huawei EC226 (3G/EVDO)?

View 1 Replies View Related

Ubuntu Networking :: 10.4 Can't Connect To Huawei E1550 Usb / Get It To Work?

Apr 22, 2010

I connect Huawei USB mobile connect to my laptop with ubuntu 10.4 64bit but I cant connect to it when I try to add Mobile Broadband connection .

I see it in lsusb

Code:
lsusb
Bus 002 Device 003: ID 12d1:1446 Huawei Technologies Co., Ltd.
but when I dont know what will i do to enable it and connect with it

I was able to use it normal with my old laptop and ubuntu 9.4 & 9.10 32bit

but with my new laptop I cant use Ubuntu 9.10 with it so that I used 10.4 beta version .

View 1 Replies View Related

Ubuntu Networking :: Low Browsing Speed Using USB 3G Huawei E1550?

Jun 2, 2010

USB 3G Huawei E1550 modem is used for connecting to the internet.When I'm connecting to the internet modem light is blue (it means that I'm connecting using 3G network)I have issues with speed when browsing internet (using Firefox and Google Chrome) or updating software using apt-get (download speed around 1.5 - 6 kB).At the same time I can download files using Transmission with 60 - 120 kB.

View 1 Replies View Related

Ubuntu :: USB E1550 Modem - Cannot Send Or Receive Messages

Jul 19, 2010

I have USB modem huawei1550 and it work nice but I have one problem that I cant send or Receive messages because my pc dont recognize my usb as usb modem.

View 2 Replies View Related

Ubuntu Networking :: Fonic UMTS USB-Stick Huawei E1550 Ubuntu 10.4 LTS Install

Jul 2, 2010

A few days ago I ordered a UMTS USB-stick from Fonic and I received a Huawei model E1550. Win and Mac install files are on the stick, but nothing for Linux. I found for the USB Modeswitch "drivers" at www.draisberghof.de/usb_modeswitsch/ (nothing about the program source on the producers web page - strange), but the install gave me a lot of errors, and after a while, I decide to find another "approach". I think you might find this useful. This is my approach for Ubuntu 10.4 LTS. Open your terminal and type:

# sudo apt-get install udev-extras

and add a new udev rule:

# gksu gedit /etc/udev/rules.d/15-huawei-e1550.rules

In the pop-up window make the rule like this:

SUBSYSTEM=="usb",
SYSFS{idProduct}=="1446",
SYSFS{idVendor}=="12d1",
RUN+="/lib/udev/modem-modeswitch --vendor 0x12d1 --product 0x1446 --type option-zerocd"

Save and close. To setup you mobile broadband connection go to System / Preferences / Network Connections, (or type in terminal ~$ nm-connection-editor) select the Mobile Broadband Tab, Add new and follow the assistent. The only changes I made, are the country of the provider, and the provider. (In my case Germany, Fonic) If you have to type in the settings yourself for Fonic, visit [URL] If the device is plugged, it will connect after a few seconds.

View 5 Replies View Related

OpenSUSE Hardware :: Huawei Usb Modem Not Reconnecting In NetworkManager?

Jul 9, 2011

I am running OpenSUSE 11.4 on an HP 625 laptop and uses a Huawei EC1260 USB modem to connect to the internet. The configuration on NetworkManager worked prefect and the there is no problem connecting. The problem is when I disconnect the modem manually, I am unable to reconnect it via NetworkManager. I have to physically unplug the modem and insert it again, then only I can connect to the internet again

View 3 Replies View Related

Ubuntu :: Installing Modem Huawei - Modem Can't Get Connected And Suddenly Remove From PC

Jun 10, 2010

with installing Modem Huawei E170. my modem can not connected and suddenly remove from my PC. i am using Ubuntu LTS 10.04.

View 1 Replies View Related

Ubuntu Networking :: Huawei E1552 Modem To Connect To The Internet, Everything Was Going Well When Suddenly Modem Stopped Working?

Feb 8, 2010

i'm running Kubuntu karmic and i've been using a 3G Huawei E1552 modem to connect to the internet, everything was going well when suddenly my modem stopped working. I've tried reconfiguring everything, i even reinstalled kubuntu from scratch with no success.Here's a part of my /var/log/debug

HTML Code:
Feb 8 17:14:01 alberto-laptop kernel: [ 1532.099883] usb-storage: device found at 7
Feb 8 17:14:01 alberto-laptop kernel: [ 1532.099888] usb-storage: waiting for device to

[code].....

View 4 Replies View Related

General :: Install Huwawi E1550 Usb Modem And Configure It With "nagios"

Jun 28, 2010

im using Centos 4.8 server system.. i want to install huwawi e1550 usb modem and configure it with "nagios". Can anyone help me to install huwawi e1550 modem.

View 1 Replies View Related

OpenSUSE Network :: Huawei E169 Not Working

Feb 7, 2010

I've just installed openSUSE 11.2 (KDE 4.3) on my Dell 1720 lapcrusher (a fresh install - had no space to install next to my old openSUSE 11.0, so had to wipe that). I have a huawei e169 (e620) that worked fine in 11.0 (after some initial trouble/configuring, details of which I cannot remember) using knetworkmanager, but try what I might in 11.2 I cannot get this HSDPA modem to connect to my ISP (Virgin Mobile Broadband in Brisbane Australia).

I'm looking for some advice on where to start - first up the modem is detected fine in KDE 4.3, I can setup a profile with the correct APN "VirginBroadband" and "blank" inserted for username/password, and PAP enabled and CHAP disabled - thats pretty much how it was setup under openSUSE 11.0, and it will try to connect but always will not authenticate - I'm not sure at which stage of authentication the process goes pear shaped. I've tried different combos of turning on/off compression/echo options etc, turning on/off MSCHAP/MSCHAP2, but to no avail.

View 9 Replies View Related

OpenSUSE Network :: Huawei E200 Usb Stick Is Not Working In 11.3

Sep 3, 2010

Although my Huawei e200 usb stick is working well under ubuntu, its not working in openSUSE. I think the udev rule provided by the vendor is suited for a debian system and not for openSUSE. When i see the dmesg output, it adds driver for ttyUSB0 and as soon as it adds it also removes it. This sequence goes on continuing till i unplug my usb stick from my computer. The udev file(78-haier.rules) provided by the vendor is as follows:

ACTION=="add", SUBSYSTEMS=="usb",
ATTRS{idVendor}=="201e", ATTRS{idProduct}=="1008",
ATTRS{bNumInterfaces}==" 1",
RUN:="/usr/sbin/haier.sh 201e 1008"
ACTION=="add", SUBSYSTEMS=="usb",
DRIVERS=="option",
ATTRS{bInterfaceNumber}=="00",
SYMLINK="ttyMODEM"

The haier.sh script that the udev runs is as follows:

[Code]...

# may not use this driver if the product id is already compiled into another driver modprobe -a option echo "0x${VID} 0x${PID}" > /sys/bus/usb-serial/drivers/option1/new_id

View 2 Replies View Related

OpenSUSE Network :: Make Huawei E173-s Work In 11.3?

Mar 26, 2011

I have a 3G modem Huawei e173s-6, the usb id is 12d1:1c0b. It's only detected as storage, not as modem. According to some tutorials I've found, I had to use usb_modeswitch and udev rules to make it automatically switch to modem mode, and usb id 12d1:1c05. I followed the tutorials, and the usb changes the id, but after the switch it is still recognized only as storage.

I have the suspicion that I have to add the driver to the kernel, since this is 11.3, but I haven't the slightest clue what to do. Does someone have experience making this modem work in 11.3? tutorial: USB_ModeSwitch ~ View topic - Huawei E173s working config

View 4 Replies View Related

Fedora :: Huawei 3g Modem E153 On F14 ?

Apr 5, 2011

How can I get Huawei 3g modem E153 connects on F14 ? I've tried settings in network manager applet to set it with no success.

View 3 Replies View Related

Ubuntu Networking :: Huawei Modem In 9.10

Mar 22, 2010

I moved from Debian to Ubuntu a few months ago, with everything working fine, except my 3G modem (which worked with wvdial and umtsmon in Debian).

The packaging claims that it is a Huawei E160, but lsusb says different: E220 (12d1:1003).

I've followed various instructions from these forums and the wiki, and it seems to be being recognised as a modem (I can set up an O2 prepaid (UK) connection), but it refuses to connect.

View 8 Replies View Related

Ubuntu :: Sms Software For Huawei Modem?

Jan 29, 2011

I use a Huawei modem, a good software / a method to send and read sms from my modem phone number ...

View 2 Replies View Related

OpenSUSE Network :: Serial Response Timeout With Huawei E169

Jan 4, 2009

I would like to get my Huawei E169 (aka. Vodafone Mobile Connect K3520, E620 etc.) USB UMTS/3G modem running with my openSUSE 11.1 x86 installation on my MSI Wind U100. The GPRS/UMTS connection works perfectly fine with the stand-alone application Vodafone Mobile Connect for Linux. However, there's the drawback that this app overwrites /etc/resolv.conf (leads to DNS issues if I would like to connect via NetworkManager again) and doesn't disable the off-line mode for Firefox automatically. Consequently, I would like to use NetworkManager for the GPRS/UMTS connection, too.

The NetworkManager configuration dialogue (I'm using the GNOME applet) seems to recognize the plugged USB stick without any issues (I get a radio button for "Huawei E620 USB Modem" in the respective add connection wizard). So I've created the configuration for my provider and saved it. After that I've tried to connect via the applet. However, approx. 2 seconds after I selected the connection, the applet says "Network disconnected" (German: Netzwerkverbindung getrennt) and the stick also obviously doesn't get connected (visible via LED). I created several new connections with different names, replugged the stick, rebooted with and without the stick plugged, but without any success. I also installed the special RPM package which is recommended in Huawei UMTS USB Stick - openSUSE, but - of course - the corresponding 11.1 package. I also used the application manually and got the following result: Looking up for HUAWEI modem and switching modem to BBO 06

[Code]....

Can this time out of the serial command be the reason for the unsuccessful connection? And if yes, how can I force the system to wait longer here? Moreover, I'm wondering, that the GNOME NetworkManager applet doesn't allow me to enter the DNS entries for my GPRS/UMTS connection. Where can I add these entries manually or is that not needed?

View 9 Replies View Related

OpenSUSE Network :: Huawei E122 HSPA USB Stick Not Working Under 11.3

Aug 31, 2010

I upgraded from 11.2 to 11.3 and with great disappointment I discovered that my HSPA modem, that worked out of the box under 11.2, work no more. At the first attempt NetworkManager is able to build the connection, I am able to use Yast to download new packages and online updating but at the first use of firefox the internet connection hangs up. Any attempt to disconnecting/reconnceting the usb stick gives the following error in the kernel echo:

[Code]....

View 2 Replies View Related

Fedora :: Configuring The Huawei E220 Modem?

Aug 23, 2009

I want to configure the Huawei E220 modem I recently bought in Fedora 10. I read lot of detail documents in the internet. All were interesting and explaining the wvdial.conf file. The problem I have is that, the file asks for the phone # to dial, username & a password. I don't have these information since my ISP didn't provide those. It works perfectly in Windows, in which above information are not needed, because when plugged in Windows, a software installation launches, which does the job to connect to the internet. So, is there a way to configure the modem to connect to the internet without those information. Because my ISP refuses to provide those, when I called there customer services.

View 3 Replies View Related

Ubuntu Networking :: Can Not Use A Wireless Modem Huawei 160

Jan 15, 2010

ubuntu I can not use a wireless modem huawei 160.type can only be used in windows.well to be used in my ubuntu linux? whether there is a script that used.

View 2 Replies View Related

Ubuntu Networking :: USB Modem Huawei E180v With 8.04?

Sep 9, 2010

Apparently it works with >Ubuntu 9.04, but I need 8.04..I'd had an older modem working on the same system, so its really something to do with this newer ones.

Symptoms:

lsusb shows little, no /dev/ttyUSB* devices
lsusb
Bus 004 Device 001: ID 0000:0000
Bus 003 Device 001: ID 0000:0000

[code]....

View 1 Replies View Related

General :: How To Install HUAWEI EG162G Modem

Nov 24, 2010

How to install HUAWEI EG162G modem?

View 3 Replies View Related

OpenSUSE Network :: Huawei SmartAX MT810 Connection At Boot (arnet)

Feb 5, 2010

I was absolutely dazzled, but my wife made me drop it after 20 days of not being able to get an internet connection.

I thought of trying again after so long to see if things had become easier for every Argentina user who has a Huawei connection (more than half of the country).
Unfortunately not.

The problem is the following:

I have a Huawei SmartAX MT810 usb-modem/router. In order to establish a connection, I need to run the following commands AS ROOT (which is why I cannot use a simple kde autostart bash script)

Code:
modprobe br2684 ; br2684ctl -c 0 -b -a 0.33 ; ifconfig nas0 up ; pppd call adsl

What's more, these commands cannot be run before the modem is operational, since they will end with an error.

In other distros I used to place these commands in /etc/rc.local. I tried placing them in /etc/rc.d/boot.local , but with no success: they are executed before the modem is operational.

In my complete ignorance of all things computer-related I thought it would be a good idea to place a caveat before the execution of the commands:

Code:
READYorNOT=$(dmesg | grep "modem operational") ; while [ "$READYorNOT" = "" ] ; do echo "Modem not operational" ; done

As a result the whole boot sequence gets stuck until I hit ctrl-c.

View 8 Replies View Related

OpenSUSE Network :: Huawei E 1750 - Connect In Live Cd - Recognize The Device

Oct 16, 2010

i tried to connect whit this key on opensuse 11.3 but i can't the device is recognized i start to connect it and the system show me "activating" but the light never comes blue , it's always green and it's impossible go to internet i use kde..

View 1 Replies View Related







Copyrights 2005-15 www.BigResource.com, All rights reserved