i'm running suse 11.2 and using a ZTE mf627. thus far i can connect to the internet using usb_switcher/vwdial but i want to share it across a LAN. all the how-to's on connection sharing I've seen use the network manager/network settings, but the device doesn't show up in either
View 2 Replies
I know that this is easy, but I am confused.I have three computers all with a clean install of SUSE 11.2. Two of them use wifi with the internet and the third is wired.I would like to share files between them all of them.When I go to dolphin/network there is nothing there and I don't know how to set it up.
View 1 Replies View RelatedI just installed suse on this computer, and am wanting to allow other computers to store files on it as a file server. I was reading the online manual and in the personal file preferences, it shows an option to enable 'share public files over network'. The problem is I don't see that option when I open up file preferences. All I see is an option to allow sharing using bluetooth, nothing about sharing over the network. When I look in the network I can see the computer running suse, but when I try to connect to it, it says 'unable to mount drive: connection refused by server.'
View 3 Replies View RelatedI have two Suse un-firewalled computers connected via NFS. About a year ago I found instructions for a very SIMPLE way to share a CUPS connected printer using Yast. When I installed 11.4 I lost the instructions. It required no config file editing and took about two minutes. Google searches focus on complicated SMB-Linux connections like those suggested by swerdna.
View 6 Replies View RelatedWhat's the best program for filesharing? And could I share from opensuse to w7 starter?
View 4 Replies View RelatedI have an opensuse machine - 11.4, running KDE as my desktop. My wifes computer is a Windows 7 PC.
I have installed SAMBA and have configured it to load at each boot. I have set the domain name to WORKGROUP as this is domain name my wife has on her pc. I have shared the video folder within Dolphin in KDE. I'm uncertain about the meaning of the netbios setting (despite reading Chapter29.Samba) and whether I should adjust this setting. Basically, I'm able to see my wife's computer name within Linux, though within Windows, I'm unable to see my linux network. Is it due to the settings that I currently have on my linux pc. The documentation that I'm reading so far is confusing for me.
I want to know if you can make a share on Samba and if you access the file you need to put a username and password in and can you save that to the server. If you can give me a step by step guide how to do it or give me a link where I can go read up on it.
View 2 Replies View RelatedI have installed OpenSUSE 11.4 on my PC. Want to share my files with Win7 system. So far so good, I can access my files on Linux computer from my Windows PC. My problem starts when I want full access to my files, as you see on image it says directory is Public and Writable but still I can't delete or add files to that directory what did I missed ?
View 9 Replies View Relatedshare internet connections with clients on the above os
View 2 Replies View RelatedI have two ethernet cards eth0 and eth1:Where the internet is cable is conneted to eth0 I have another system i have connected a cable through eth1 to my second systems network cardnow i am able to access the internet on eth0 i.e.,on my first system ..ow can i share the internet which ius coming from eth0 to another system using eth1
View 4 Replies View RelatedI have bought a new USB modem from my service provider. The model they provided is "Huawei EC1260" Huawei Terminal. As usual the official support is for windows and mac.
I tried to install this device using two methods..
1) Set knetworkmanager settings to "traditional with ifup". Then in wireless setup there is a choice of having "usb" (A tick box). I selected that, and setup completed successfully but the knetworkmanager was not up(I did ifdown wlan0 (wlan0 was the wireless config name), ifup wlan0 and the rcnetwork restart.)
2) Again knetworkmanager was set to "traditional method with ifup. This times while adding the connection I specifically selected the type "USB", then clicked to finish the configuration. The configuration finished without any errors but when I checked the Network Configuration screen no USB device was added there.
Are there any specific steps to configure a USB modem
trying to make my 3G modem (a ZTE MF622) work with OpenSUSE 11.2. KNetworkManager is recognizing it (so I suppose it's not on Storage Mode), I can create the 3G connection and connect, but I can't navigate on any sites (ping gives "unknown host" for any IP). Also, the KNetworkManager applet doesn't show anything on fields "Name servers" and "Domains" (they are blank). Tried some instructions from the internet here and there, but didn't have any luck.
View 9 Replies View RelatedI'm trying a long time to configure my 3g modem to connect.I had tryied using the KDE Network manager and the modem stay in "Waiting authorization" for ever ^^.The KDE Network manager runs ok in Kubuntu.I had tryied download and install kppp, but kppp don't open my modem (/dev/ttyUSB01)Then how can I configure my modem?
View 1 Replies View RelatedI have a devolo MicroLink 56k Fun LAN modem, which I could configure in openSuse 11.2 as an DSL device. With 11.2 it worked fine. But it isn't possible in 11.3 to configure it, because I cannot set the dial up internet provider phone number for this DSL device.I also tried it to configure it as a modem, but then it used the /dev/modem device, which is the wrong device for this LAN modem.
View 3 Replies View RelatedI have a box with 1 ethernet card and Huawei E160 USB modem. So, I have configured eth0 interface with IP 192.168.1.1 and modem0 interface with dynamically assigned IP. Now, I'd like to share Internet from modem0 to eth0 and so to the rest of home local network.
I need your advice on how to do it. All the manuals I've read deal with two ethernet cards that have static IPs. It seems that YAST lacks the GUI for it, too. Also, I need the configuration to work even with no user logged in so I'm using ifup instead of NetworkManager.
I am using 11.4 gnome desktop on hp elitebook 8440w. I have a reliance netconnect plus usb modem. (ZTE AC 2726).
Initially it was recognized but didn't work. But now system is not recognizing it. What should i do. Please suggest.
I want to share files between my desktop box and my laptop either by my mains-LAN or by ethernet cable and cannot find anything on the forum to point me in the right direction. There is plenty of information to help with the installation of Apache/LAMP and the like. But is this what I need? Will I need to create logon IDs to the desktop to share files (and even the printer?).
View 9 Replies View RelatedI am running a 3-G wireless USB broadband modem, and connecting with Network Manager, but I keep getting disconnected when idle after 5-6 minutes. I am used to using Kinternet to connect with my 3-G wireless USB broadband modem, and setting it up in Yast / Network / Modems, but was not able to configure my modem there (for some mysterious reason) so ended up using Network Manager instead.
What's going on here regarding YAST being unable to configure my modem (even when Network Manger is disabled). But my main problem at this point is that my connection times out after about 6 minutes if I'm idle. This is a big problem for me because I type slow and frequently get disconnected while posting on message boards. Where are the idle time out settings are for Network Manager? I can't seem to find them.
I just loaded 11.2 & Kde 4.3. Installed both Kinternet and Kppp. My modem is a USR PCI HW modem 2976. Hardware Info shows it connected to /dev/ttyS4. I configured the modem with Yast as modem0. The user access box is checked for Kinternet Both Kppp and and Kinternet will dial out.
The connect response comes back from the ISP and either of the dialers will hang and the dial tone comes back. The firewall is showing modem0 in the External section. Nothing changes if I shut the firewall off.There's nothing in the dmesg I could find. Could this be a pppd permission problem?
My machine is running on a dual-boot Windows Vista/openSUSE 11.2 scenario. I have been trying to get my Huawei E1550 to work on Linux for the past few days trying numerous methods suggested in other forums from people with the same problem, but I have not produced any fruitful results.
Plugging in the USB modem results in Linux detecting it as a CD-ROM. I have installed usb_modeswitch in attempt to switch it to a modem, but Linux still fails to recognize it. Windows Device Manager and lsusb both give ProductID=1001 and VendorID=12d1 connected to USB1. I'm guessing since Windows detects the correct IDs, the Linux versions should also be correct. In any case, I ran usb_modeswitch with the Default IDs for /etc/usb_modeswitch.conf, which gave 0x1446 as the ProductID, not 0x1001. Upon running usb_modeswitch, the product ID could not be found so the program fails and quits asking if it's connected (and it is).
Just to test, I also ran wvdial which unsurprisingly did not detect the modem and could not send the init strings. All commands were done using root privileges. Also note that when after usb_modeswitch is run and upon plugging in the USB, NetworkManager pops up near the tray saying "attached" but still shows the device as a CD-ROM.
I have an external usb dial up modem. lsusb shows: Bus 001 Device 002: ID 2001:f10d D-Link Corp. [hex] Accent Communications Modem How do I set this up? It probably needs a driver, how do I check it, or better yet, can I get yast to tell me if it recognizes the modem or needs firmware? I know linux and dial up is like the seventh circle of hell. Just wondering if there was a snowball's chances of getting this working. Sorry if this is the wrong section to ask in. Seemed like as good as any when I checked.
View 9 Replies View RelatedI have a US Robotics serial modem, and I have smpppd enabled in system services, with wvdial and kppp installed. When I try to set the modem up using yast, I keep getting hung up by the different screens. First a screen that asks if I need to dial a number to get out. I have to dial 9, so I have that entered. Then a screen that asks for "country" and "provider."
When I try to enter anything, nothing shows in the boxes, so I go to a screen that asks for the phone number, provider, user name and password. When I enter those, it goes to a screen that wants "Connection Parameters", with default settings and the "buttons" at the bottom of the screen "muted," or flattened out, i.e. unusable. That makes it impossible for me to set the information as saved, so it's back to the beginning and sart over, with the same results over and over. How do I get the modem so it dials out?
I have a Zoom 2920 internal hardware modem that worked well with Suse 10.0. In Suse 11.3 the modem config. overview lists 2 modems for this one board; #1- AT Modem and #2- Venus Modem (v90, 56K Flex). With #1 "edit" brings up modem parameters and the modem device line is blank. With #2 the device line shows /dev/ttys4.
When the provider parameters are entered, for either #1 or #2, the modem overview continues to list them as not configured but a third line "modem 0" is configured with the provider information at /dev/ttys4. The modem will not function.
I got a new cable modem so I could get rid of the one I've been leasing from the cable company. It is a Motorola sb6120. Everything is fine with the ISP, it's approved for operation on their network, the only hitch was I had to use my Windows laptop to run their activation software.
At any rate, with the new modem installed, I hop on my Linux box and go to work. I'm seeing some terrible delays in looking up names. When I look with firebug, all the dns lookups for new names are taking 15+ seconds. First I just think maybe the names aren't cached or something is weird for a minute and it will get better, but no. After several restarts and then a couple days persevering with the new cable modem, all DNS queries are still terribly slow (including zypper, mail client, web client).
Suddenly I remember an issue I was having with, I believe version 11.1 when I first installed it. For just the computer on my network with a fixed IP address, DNS resolution was slow like this and if I disabled IPv6 then all was well. I believe there was even a patch issued back then for gethostbyname() that was supposed to fix the issue? So, when I disable IPv6, DNS lookup is back to normal. The two Linux computers on my network had been working fine with IPv6 and the old modem, though, and the Windows box is still working fine even with the new modem.
I can disable IPv6 and make it fast again, but really why should I have to?
My computer is already connected to a 100Mbps LAN. I can use wvdial to connect to internet using a modem when I have my LAN disconnected. Now, I want to share this modem internet to one of the IP addresses available on LAN. Say 10.100.99.56 for example.
View 3 Replies View RelatedHave followed swerdna's guide as in the past and my wife from her win7 computer can see and has read write access to all the shares & can print to the shared printer attached to the Opensuse computer etc. However, when I try to access her Win7 shares from my opensuse computer I am presented with a username / password prompt. Here is my smb.conf
[code]...
have followed swerdna's guide (as mentioned previously) and set 'password protected sharing' to off on the win7 computer.
If I connect with a 3g modem or with wireless sometimes the resolving does not work. This happens on opensuse 11.2. nslookup and dig works but nor ping nor ssh nor any other network application does work If I modify the /etc/resolv.conf after connecting to a wireless network for example it does not work even the dns are known And more strange if the resolver works and I modify /etc/resolv.conf with known dns the resolver does not work anymore. BTW: the dns entry from the wireless is 192.168.1.1 and I do not have any idea how the wireless ap is configured... so it could be in this case that dns is not forwared only allowed to use 192.168.1.1 but the other case is a 3g modem which not even the propagated dns entries works in the bad case
View 9 Replies View Relatedkppp frozen in initializing modem.I wait for many second but no dialup, in configure panel set /dev/modem on modem , Query properly working , but when connect , in initializing modem kppp stoped.
View 1 Replies View RelatedI'm using OpenSuse 10.3. I have a stick modem of Zain (Sudan), I use it for the internet. I need help on how to configure OpensUSE 10.3 so I can use it for the internet.
View 7 Replies View RelatedI am trying to connect my huawei e160 usb modem but it keeps failing and does not show on the Network Manager, checking on /var/log/messages this it what I get:
Oct 5 15:31:30 LPKENBITD002 modem-manager: (ttyUSB1): re-checking support...
Oct 5 15:31:30 LPKENBITD002 modem-manager: (Huawei): (ttyUSB1) deferring support check
Oct 5 15:31:33 LPKENBITD002 modem-manager: (ttyUSB1): re-checking support...
Oct 5 15:31:33 LPKENBITD002 modem-manager: (Huawei): (ttyUSB1) deferring support check
Oct 5 15:31:36 LPKENBITD002 modem-manager: (ttyUSB1): re-checking support...
Oct 5 15:31:36 LPKENBITD002 modem-manager: (Huawei): (ttyUSB1) deferring support check
