We have Redhat 9 proxy server with 4 lan cards using 1 static and 3 internal private ips,as there is no pci slot in the pc for fifth lan card so i have to purchase usb lan card.
My question is that can the redhat9 will detect the usb lan card if it will detect the usb lan card then I will purchase the lan card
I am facing problem with onboard lan card. i think its not detecting. when i type ifconfig command it shows below details
I have installed red hat. but not able to give ip.
The existing sound card that I have, has a connector for this.
It is an "HD audio", or an AC 97 connector. There two rows of
five pins, with one pin blocked up, so that the connector is
inserted in the correct manner. The cord is hard wired to the case.
Here are the requirements:
- gets instantly recognized by Linux (Redhat 5) 64 bit, and plays sound
with the standard Linux drivers. I believe I have all of the drivers installed,
because a few cards do play with them automatically.
- no installation of special Linux drivers required.
- the other big requirment is that the card have output to an HD Audio,
or AC 97 connector, and will play music through the headphone jack.
(Believe it or not, I have one card that works fine out the back,
but won't work through the HD Audio. But it works fine in Windows)
- will also work with Windows 64 bit.
Any good sound card recommendations that will meet these requirements?
The message I get when I try and activate is "3c501 device eth0 does not seem to be present. delaying initialization."
Does anybody know what cards are compatible without downloading drivers and other such exercises?
how to configure squid in linux redhat & also how to fid out n/w card driver
View 2 Replies View Relatedplease anybody tell me how to check the availability of ethernet card in redhat 5.2 without using screw driver.
View 3 Replies View RelatedI had Windows XP working. I then put in a new hard disk and installed Redhat 5 on it. rom then i could only boot into Redhat. Further, everyting is very slow. Anothe rproblem is that Redhat does not see my netwrok so I cannot get onto the Internet. I need to have the choice of booting into XP or Redhat.
View 2 Replies View RelatedI cant mount a directory on red hat 5 from red hat 4 using fstab.I keep getting permission denied.I mount directories on the same red hat 5 sys from other red hat 5 and 2 old HPUX systems using fstab.When I try to telnet to it i get "no route to host."
View 3 Replies View RelatedI have been trying to configure DNS using "bind", however i dont have a named.conf file in the vars and etc
View 1 Replies View RelatedI'm running Ubuntu 10.04 Server. I can't get my Wireless Card & Wired Card to work at the same time. My interfaces file is incorrect, when I comment out 1 of the interfaces the other works. I have attached my interfaces file.
View 2 Replies View RelatedI recently installed Xubuntu on my old P3 laptop (Compaq Armada E500 if anyone is familiar). The laptop is a bit old, so both wired and wireless networking is done via PCMCIA cards. I have 2 cards installed, one for each purpose. I can't find the dongle for the wired card right now, so I am trying to use the wireless card. I am able to find the network I want to connect to, and type in the password since the network is secured. It tries to connect but then pops up again asking for the password (I know it is correct). Is this card supported by linux/compatible? I tried finding drivers online but the sites that had drivers were down.
View 1 Replies View RelatedJust installed Fedora 14 from the Live CD i686 on my Dell Inspiron 1521. I can't connect to the SpeedTouch 585 on either wireless broadcom card or the wired Ethernet card.
I can connect to it from the same Laptop on the Vista which is on dual boot on the same laptop.
Further confusing is that I ran Fedora 14 and connected to another SpeedTouch today.
Already checked the Channel on the wireless nic and it's on the same one as the SpeedTouch.
i m kapil sharma, i want to know about linux server configration in redhat linux 5.0? how i configure ICS service in rdhat linux 5.0? i have two lan cards in the system and one ip address assigned by ISP.I want to configure linux sever to share this ip address in network approx 100 pc's of widow's xp.
View 4 Replies View Relatedi ve installed RH-5,xp in my desktop(dual boot), my xp internet works well, recently i installed RH & want to setup internet conn in RH.
View 3 Replies View RelatedI'm an it student and a newbie in linux OS.
We have this final project that we have to set-up
a firewall in a linux redhat OS which i totally have no idea ..
i did some research but haven't found the right one.
I have installed redhat linux5.I have wireless internet connection at home. wireless internet connection working fine in window 7 but not in redhat linux . Also wireless LED is not lighting in redhat . I have inbuilt intel wifi 5100 AGN card which is not detecting in redhat.rehat comman output which will help you
*****************************lspci -v *********************
[root@localhost ~]# lspci -v
00:00.0 Host bridge: Intel Corporation Mobile Memory Controller Hub (rev 07)
Subsystem: Dell Unknown device 02bb
[Code]....
How to do PTCL broadband settings in redhat.in windows i just do followingRight Click My Network Places on desktop and select Properties Right Click Local Area Connections andselect Properties.In the General Tab; double click on Internet Protocol (TCP/IP) and made the following settings:
ip: 192.168.1.2
subnet: 255.255.255.0
gateway: 192.168.1.1
preffered dns: 203.135.0.70
alternate dns: 203.135.1.117
How to set up DHCP server in Redhat Linux 6
View 1 Replies View Relatedhad a box lose it's virtual IP address on the eth0 card. I rebooted the box but it just would not give the card the second IP address. We rebooted several times in fact.Today admin ran 'ifup ifcfg-eth0:1' and the virtual IP was there. Nothing was changed, just that command was ran.I thought there might be a problem with the automagical stuff so I rebooted the box again, virtual IP is there and happy.Anyone know why it would not have come back on reboot and why it now does?
View 7 Replies View Related1. im working on several distros, sometimes i dont remember the syntax of the ethernet settings (i.e those directives in /etc/sysconfig/network-scripts/ifcfg-eth0,or /etc/network/interfaces ) in redhat its IPADDR,NETMASK etc..
in ubunto its:
iface eth0 inet static
address 192.168.1.5
netmask 255.255.255.0
gateway 192.168.1.254
so,where exactly is the man page for this information, i tried (in centos) to type man -k "IPADDR" to find some reference but i come up with nothing.
2. sometimes im logged as user "user1" and then i do "su user2" and then again "su user3",
i would like to know how far the nesting is and who was first.. i.e is there any command to give me this output: "user1->user2->user3"?
How To Enable networking in redhat i have tried all the possible way to enable it but it doesnt work..it shows my localhost name and details but it cant connect to it.i have tried system-config-network command but blue screen splashes.
View 1 Replies View RelatedI'm using a program on a group of servers which contact each other using SSH. I've got the authentication keys setup with no password but when one box tries to connect to another it wants the password for the user it's trying to communicate with. So the main problem is there is a lot of communicating within this program so it's important to allow each box communicate with each other without the use of a password. I'm using OpenSSH 4.3 with OpenSSL 0.9.8 on Red Hat Enterprise Linux Server 5.3 (Tikanga). I'm also using SSH on Ubuntu(Intrepid) to connect to these servers at the mo as i don't have direct access to the boxes.
View 4 Replies View Relatedhow to add redhat linux5 client to windows domain
View 1 Replies View RelatedI am using RHEL 5.2. I want to configure Dynamic DNS on it. Can anyone tell me how to configure Dynamic DNS on RHEL 5.2
View 1 Replies View RelatedWe are using Broadband 2 Mbps (India) connection in Redhat Linux 5.In Server there are two network card.ne is connected to Broadband another one is connected to LANthat meansEth0 Address : 192.168.0.5/255.255.255.0 gateway 192.168.0.1Eth1 Address : 10.0.0.5 /255.0.0.0How to configure NAT in Linux Machine#iptables -t nat -A POSTROUTING -o eth0 -j SNAT --to 192.168.0.5#echo 1 > /proc/sys/net/ipv4/ip_forward
View 2 Replies View RelatedI've read there is a way to communicate without tradtional TCP/IP programming on Redhat Linux and Nehalem CPU with ethernet. I've tried to collect some related information with sample program codes, but failed to collect useful information.
View 1 Replies View RelatedWe have 20+ Redhat servers on our network and every so often our DHCP server goes down. When it comes back up we have to go around to all of our RedHat servers and restart networking manually. Other OS's (Ubuntu, Windows, etc..) will continually try to get a DHCP lease so that when our DHCP does come back up it requires no work from us for them to get back on the network. But it seems that Redhat only tries once and if it fails it never tries again. Have to go around to 20 different servers (some of them are at remote locations) is less then ideal when this happens. how we can get Redhat to continually try to get a DHCP lease like other OS's?
View 1 Replies View RelatedI installed Redhat nash version 5.1.19.6 with kernel 2.6.18-128.el5-xen-i686 on a Dell Inspiron 1300 with Broadcom BCM4401 (eth0/LAN) and BCM4318 (eth1/WLAN). eth0 is working fine, but eth1 was causing trouble. After some difficulties with missing packages I managed to install ndiswrapper, blacklisted module bcm43xx in /etc/modprobe.d/blacklist and removed it, loaded module ndiswrapper and had connection. But after reboot module bcm43xx was again loaded. So blacklisting does not seem to work.And additionally strange to me, I cannot unload module bcm43xx anymore. And if I load ndiswrapper driver bcm43xx is still used as the terminal command 'dmesg' is showing me in the system log, while ndiswrapper was used when the connection was once and only once established
View 13 Replies View RelatedRecently I installed RedHat Enterprise 5 on a windows machine. The machine is configured to use DHCP, but I have been seeing some strange behavior if I do nslookup on the machine's IP:
[someuser@lin01 mydir]$ nslookup 10.5.x.x
Server: 10.10.x.xx
Address: 10.10.x.xx#53
x.x.5.10.in-addr.arpa name = xyz.something.
x.x.5.10.in-addr.arpa name = lenovo-d1690047.
x.x.5.10.in-addr.arpa name = pqdlds.
x.x.5.10.in-addr.arpa name = lin01.mydomain.com.
Where only the last entry of [URL] is actually correct, how can remove the other entries? I spoke to my IT Manager and he cannot see these stale entries in the DNS (we are using windows AD)
I m using redhat enterprise linux 5 desktop
i hav a broadband connection through bsnl dna-a211-1 modem
how to activate the connection into my laptop with redhat enterprise linux5?