Networking :: Configuring DNS On Redhat 5?
Oct 21, 2010I have been trying to configure DNS using "bind", however i dont have a named.conf file in the vars and etc
View 1 Replies
ADVERTISEMENT
General :: Heartbeat Configuring In Redhat?
Oct 20, 2010I'm currently trying to configure Linux heartbeat on my two Linux servers(where SMPP service is running) my two machines are in two different location with different notworks (primary is in 192.168.x.x and secondary is in 10.48.x.x network)
I want to know whether is it possible to configure heartbeat between two such different networks (what i found by surfing internet is the way of configuring in same network) if possible, can i configure to listen to my primary server IP instead of having a secondary IP in primary server (since my SMPP service is running with my primary server's IP)
Software :: Configuring Openvpn-2.1.4 On Redhat As Client Server Using Key?
Mar 20, 2011I want to configuring openvpn-2.1.4 on linux redhat as client server using key, but there is some drawback
[Code]...
CentOS 5 :: Configuring Redhat 5 Enterprise Workstation To Point To 5 Repository Updates?
Apr 7, 2011If I have Redhat 5 Enterprise workstation, how can I configure it to point to Centos 5 so I can receive updates and fixes through Centos rather than paying for Redhat support ? I heard this can be done, but wasn't sure what the steps are in terms of configuring Redhat
View 4 Replies View RelatedGeneral :: Configuring Redhat As Domain Controller And Adding Windows Workstations As Clients
Feb 28, 2011i need to configure Redhat Linux as Domain Controller in my organisation, whee all of my clients PC's will be Windows XP or Windows 7 ( where i can login through Domain users ). what exactly i need to configure in Redhat Linux, i heard Configuring Samba as PDC is quite enough ? is that right ? then what is Open LDAP ? should i need to Configure Open LDAP also ?
View 2 Replies View RelatedRed Hat :: Redhat 5 Windows XP Dual Boot Boots Only Into Redhat?
Jan 11, 2011I had Windows XP working. I then put in a new hard disk and installed Redhat 5 on it. rom then i could only boot into Redhat. Further, everyting is very slow. Anothe rproblem is that Redhat does not see my netwrok so I cannot get onto the Internet. I need to have the choice of booting into XP or Redhat.
View 2 Replies View RelatedGeneral :: Cant Mount Redhat 5.0 From Redhat 4.0 Via Fstab?
May 5, 2011I cant mount a directory on red hat 5 from red hat 4 using fstab.I keep getting permission denied.I mount directories on the same red hat 5 sys from other red hat 5 and 2 old HPUX systems using fstab.When I try to telnet to it i get "no route to host."
View 3 Replies View RelatedNetworking :: Configuring With Two HW Interfaces?
Oct 16, 2010I have two interfaces, gprs0 and gprs1, both connected to the Internet from the same HW device, but through two different access points I just read another blog entry with a guy who had two network cards, using one as a back up - I guess this is a little similar, but should be much easier I am guessing - I am just lost Using ifconfig (IP address given by the network) and route to setup the connection,
ifconfig gprs0 10.20.30.40 up
route add default dev gprs0
ping 66.102.7.99 works fine
afterwards
[code]....
There is data being transmitted and received to device again, I guess the kernel just doesn't know where the incoming data should go without the correct routing tables? Or what exactly is going on?The question I have is how do I configure the device to do the correct routing, using only the ifconfig and route commands? Maybe too trivial for you guys, but I am getting tired of goofing around not knowing what is up and down anymore
Networking :: Usb Lan Card For Redhat 9
May 10, 2011We have Redhat 9 proxy server with 4 lan cards using 1 static and 3 internal private ips,as there is no pci slot in the pc for fifth lan card so i have to purchase usb lan card.
My question is that can the redhat9 will detect the usb lan card if it will detect the usb lan card then I will purchase the lan card
Ubuntu Networking :: Configuring New Wi-Fi Router?
Mar 18, 2010I am using Ubuntu 9.10. I just got a Linksys WRH54G wireless router. I want to protect my wireless connection by putting a password to it but when I enter the Router's default IP address (192.168.1.1) into my browser to open the 'Utility Welcome screen', the browser does not respond.
According to the Router's manual this is because PC' TCP-IP is not set to automatically obtain the IP address.
Ubuntu Networking :: Configuring Internet In 10.04
Jun 11, 2010I recently bought a dell inspiron 14 n4010 and i've installed windows and Ubuntu 10.04 in it. The problem is that i'm not able to access internet in my ubuntu. I'm using asianet broadband connection and i'm able to get internet in my desktop when i connect the cable to the system. But when i did the same with ubuntu 10.04 in my laptop, i'm not able to get internet access. I'm able to access internet in windows though. But i hate using windows.
View 9 Replies View RelatedUbuntu Networking :: Configuring BSNL In 10.10?
Nov 4, 2010way of life and am having trouble accessing the internet.
View 6 Replies View RelatedNetworking :: Configuring Ethernet Bridge?
Nov 3, 2010I am using 3 machines in a LAN connected through a hub. My intention is to have a end-to-end connection between 2 machines so that I can control delay/loss rate. For that purpose, I am using a 3rd machine with 2 NIC and intend to use a bridge and installing Dummynet in this machine to control the traffic between the other 2 machines.I have successfully installed Dummynet in the bridge machine. Now I require to configure Ethernet bridge in the machine. What is the process? Do I need a kernel compilation or can be done without it? read somewhere that recent kernels can be configured without recompilation.I am using Mandriva 2010 with 2.6.31.5-desktop-1mnb kernel.
View 1 Replies View RelatedNetworking :: Configuring 2 NIC's On Ubuntu Desktop 10.04
Apr 20, 2011I have 2 pc's at home, neither v flashy but both more than capable of running this. Previously I had them both running XP SP2. One pc has 2 NICs in it and the second only one. So, PC1 (now running Ubuntu desktop 10.04) has the 2 NICs installed ...
1) A realtek NIC which is on 'eth1' and from which I receive internet connectivity from the router of this shared house. (2 other people connect their PCs to the internet via this router.)
2) A 3com NIC on 'eth0' which I have connected (using a crossover cable) to the Intel 'PRO100 VM' NIC on PC2.
Admittedly this took me some time to get half working. Currently I can connect to the internet through 'eth1' OR to PC2 via 'eth0' BUT NOT AT THE SAME TIME. However, If I disconnect one (by left clicking on 'disconnect' under the top of screen menu bar, then the other one will immediately work ... and visa versa.
I had this working when both PC's were running windows XP but now in trying to educate myself further I have installed Ubuntu on PC1 and am attempting the same thing. I refuse to accept that as alot of these thread responses state, that it 'can't be done'. Quite clearly it can be done since the physical connections and hardware are no different, its just about ensuring that the protocols are all correct and that I haven't done something stupid.
I am very keen to learn more about computer networks and equally keen to educate myself in the ways of Linux, in fact I am studying to gain a network qualification as we speak but at this stage its still a little confusing. I have learned an awful lot about the fundamentals of networking but the 'hands on stuff' is where I really need to test myself.
Networking :: Configuring The D-Link DGE-528T
May 11, 2011I have just clean installed Ubuntu 11.04 on 3.06 GHz Dual core P4 with 2GB RAM
Code:
jim@venus:~$ uname -r
2.6.38-8-generic
At the same time I purchased a Gigabit NIC from D-Link, mostly because D-Link is a reputable brand and it said on the box compatible with 2.6.x linux kernal. The original NIC is still in the system and can be seen and is functioning as eth0. The system can see the new driver and the card, here is an extract from dmesg:
[ 1.401350] r8169 Gigabit Ethernet driver 2.3LK-NAPI loaded
[ 1.401390] r8169 0000:02:02.0: PCI INT A -> GSI 18 (level, low) -> IRQ 18
[ 1.401437] r8169 0000:02:02.0: (unregistered net_device): no PCI Express capability
[ 1.403219] r8169 0000:02:02.0: eth1: RTL8169sb/8110sb at 0xf8016c00, 5c:d9:98:45:8b:cc, XID 10000000 IRQ 18
and lspci:
02:02.0 Ethernet controller: D-Link System Inc DGE-528T Gigabit Ethernet Adapter (rev 10)
02:04.0 Ethernet controller: VIA Technologies, Inc. VT6105/VT6106S [Rhine-III] (rev 86)
and ifconfig:
eth0 Link encap:Ethernet HWaddr 00:1e:58:9a:1b:0e
inet addr:192.168.11.65 Bcast:192.168.11.255 Mask:255.255.255.0
inet6 addr: fe80::21e:58ff:fe9a:1b0e/64 Scope:Link
[code]...
so as you can see dead as a door nail, no lights on the card and not picked up by the switch. How do I make this operate?
Networking :: Configuring Internet In Ubantu?
Mar 26, 2011I am using ubantu 10 and broadband where userid and passwd has been configured in router box. So when I connect this from windows its automatically connected (using ppp0e and dhcp), whereas in linux it could not connect.
View 2 Replies View RelatedNetworking :: Configuring IP Address Fails?
Jul 22, 2010I have an ARM based linux machine with kernel 2.6.10 .On reset it automatically gets the IP address 192.168.1.2 . I want it to wake up with address 192.168.35.133 .In /etc/network/interfaces was only an interface for loopback:auto loiface lo inet loopbackI have added:auto eth0iface eth0 inet staticaddress 192.168.35.133netmask 255.255.255.0But on next reset the IP was still 192.168.1.2
View 4 Replies View RelatedNetworking :: Configuring Router From Internet?
Apr 21, 2010is there a possibility to connect to my router admin zone from internet using wan ip? from lan I can do that using 192.168.x.x IP but when Im in work and something go wrong at home how can I check configuration of my router from outer world instead of lan?
View 7 Replies View RelatedNetworking :: Configuring Two Ethernet Ports?
Apr 16, 2010I have a system with one (sometimes two) ethernet ports, that works happily in an old Fedora 5 build. But I can't get it to work on a new Centos 5.4 build. Original system: One dedicated ethernet port on card always connected to the systems dedicated equipment and no external access (the system is the DHCP master for that network). An optional second USB dongle that is a second ethernet port, used for debugging and development. (This is a DHCP client with full conectivity. In /etc/sysconfig/network-scripts I have ifcfg-eth0, ifcfg-eth1 and a route-eth0. Neither of the ifcfg files needs an explicit HWADDR, which means the same ones work for all boxes. And when one needs to be connected to the network all is fine.
The system is being moved to Centos 5.4, most is working with minimal change, but I am having problems with the ethernet ports. If it only has the on board ethernet connected, all is fine. If you have the USB dongle connected things go wrong: This system brings up the USB ethernet first, and tries to assign it to eth0 (which fails), and then brings up the on board ethernet as eth1 (which also fails). I have tried forcing the behaviour of the network by setting the HWADDR(s), but this does not result in the on board coming up as eth0, it comes up as __tmpxxxx as follows:
ifconfig -a
__tmp226406138 Link encap:Ethernet HWaddr 00:80:66:07:A8:63
BROADCAST MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
[Code]...
Currently the only solution is to unplug the USB dongle through restart and plug in afterwards, and this wont work when the unit is remote and in the field.
Networking :: Configuring IPtables Security Of CPU
Mar 3, 2009I new in Linux, I have a Centos5 since sunday and well I have to configure the iptables security of this cpu, I read a lot of examples of iptables in the internet and also another Thread from here but Really a don't know what to do, I saw lots of codes but first of all I don't know where I have to write that and my teacher don't want to help me in this homework. I tried to write the codes in applications --> accessories --> Terminal
View 3 Replies View RelatedNetworking :: Configuring Pause Settings For NIC?
Feb 11, 2010i am trying to configure my NIC to support pause frames(rx on tx on)but it returns error:
ethtool -a eth0 returns error : Operation not supported I need to enable pause settings so as to make my point to point link lossless
CentOS 5 Networking :: Configuring 5 To Use Gateway?
Mar 22, 2010Recently my motherboard went out, I replaced it and booted centos 5. All went well except sound, video tuners and netoworking. The sound I re-configured, and have gotten tuners working but I am running into trouble with the new network card. The networking setup is;
DSL wireless router/modem IP 192.168.0.1 connected to XP computer through WIFI IP 192.168.0.3. all set to subnetmask 255.255.255.0 and with DNS servers 192.168.0.1 and 205.171.3.25 the XP computer is the only one that supports my wifi card. On wired LAN I share that connection to 4 devices. 3/4 work well, my cent os 5 box will not connect. here are the lan settings:
win xp: IP 192.168.0.60 255.255.255.0
mac 8.6: IP 192.168.0.34 255.255.255.0
blueray: IP 192.168.0.65 255.255.255.0
[code]....
Networking :: Configure Ics In Redhat 5.0 Verson?
Aug 11, 2010i m kapil sharma, i want to know about linux server configration in redhat linux 5.0? how i configure ICS service in rdhat linux 5.0? i have two lan cards in the system and one ip address assigned by ISP.I want to configure linux sever to share this ip address in network approx 100 pc's of widow's xp.
View 4 Replies View RelatedNetworking :: Set Up Internet Connection In Redhat 5?
Feb 22, 2011i ve installed RH-5,xp in my desktop(dual boot), my xp internet works well, recently i installed RH & want to setup internet conn in RH.
View 3 Replies View RelatedNetworking :: Setup Firewall In Redhat V5+?
Mar 4, 2009I'm an it student and a newbie in linux OS.
We have this final project that we have to set-up
a firewall in a linux redhat OS which i totally have no idea ..
i did some research but haven't found the right one.
Networking :: Internet Not Working In Redhat?
Jul 3, 2010I have installed redhat linux5.I have wireless internet connection at home. wireless internet connection working fine in window 7 but not in redhat linux . Also wireless LED is not lighting in redhat . I have inbuilt intel wifi 5100 AGN card which is not detecting in redhat.rehat comman output which will help you
*****************************lspci -v *********************
[root@localhost ~]# lspci -v
00:00.0 Host bridge: Intel Corporation Mobile Memory Controller Hub (rev 07)
Subsystem: Dell Unknown device 02bb
[Code]....
Fedora Networking :: Configuring A VPN From Home To Work
Feb 1, 2009i have to work at my home in my office. For that purpose i use a laptop with Windows (i really don't know why) XP. As i moved to Fedora 10 i want to make the same thing in Fedora.. Really don't know how. i have a cable connection and a router at my home ( i posted another message mentioning the fact of my wireless connection).
At my office i have a router , a firewall and 2 servers that i am allowed to use and i have to work on them (one is an AS/400 from IBM).
Fedora Networking :: Configuring IPTables To Allow Traffic Out
Apr 26, 2009I've tried both the firewall interface that comes with Fedora and Firestarter, neither can configure as I want. So I think I'm going to have to do it by hand. In this laptop I have one 10/100 Nic and one wifi connection, at times either of them can be connected to the network. How can I configure IPtables so that any traffic is allowed out, nothing is allowed in (other than std stateful firewall replies), no icmp and that the fw logs any attempts to connect to the laptop?
View 5 Replies View RelatedFedora Networking :: Configuring A Gig NIC For 1000/full?
Sep 10, 2009I have a Broadcom NetXtreme BCM5754 NIC and I cannot seem to get the NIC to auto link at Gig speeds. It will only link @ 100/full.
View 1 Replies View RelatedFedora Networking :: Configuring Yum To Use The Socks Proxy?
Jul 22, 2010I have an internet connection through socks4 proxy form a server nearby to my laptop(fedora 12) i need to update and install sofwares. How to configure yum to use the socks proxy?
View 2 Replies View Related