1) I have an ADSL router for internet and RHL box sitting on the southside of the southside of the router with local IP configured.
I have to access the Linux box through the internet.
I have tried to port forward the SSH port on the ADSL router, that is not working.
Because of the configuration of my house, I need two routers.I have a DLink ADSL router as my main router and the Belkin N1 as my repeater.I have set up the IP address in the Belkin to be 10.1.1.10 - my DLink is 10.1.1.1. I have disable the dhcp in the Belkin and set the DNS as ISP provided. [URL]..I have set the channel to 11 and in the Ubuntu Network Manger I have set the IPV4 to Link Local Only. I can see the Belkin and connect with my PC.but it will not take me through to the internet.
View 9 Replies View RelatedI have a desktop PC running Ubuntu 9.10 and Windows 7, and a Eee PC 701 laptop running EasyPeasy Ubuntu 9.04. I'd like to connect the desktop to the laptop with a wired connection (eth0), then the laptop to my ADSL router using wireless (ath0).
I have a crossover ethernet cable (I bought on ebay). I have set up my laptop with a static IP address on my LAN and it uses OpenDNS.
I have added this to /etc/sysctl.conf on the laptop:
net.ipv4.ip_forward=1
Then I tried this on the laptop:
sudo iptables --table nat --append POSTROUTING --out-interface ath0 -j MASQUERADE
sudo iptables --append FORWARD --in-interface eth0 -j ACCEPT
This is a variation on what I found on other sites describing how to set up a router. I don't understand iptables very well, but I gather that the above two lines should set up forwarding so that traffic from my router to the laptop will be forwarded to the desktop, and vice versa.
But this doesn't work. The connection doesn't even establish between the laptop and the desktop.
I'm a beginner in Ubuntu, I'm using Ubuntu 9.10.
Currently using a Dlink GLB-802c router and using a ADSL connection. I try to connect to the Internet but it is unsuccessful. Ubuntu is not indicating my router when I connect to the PC.
My PC is P4 and using USB to connect to internet, PC haven't a Ethernet interface.
not *buntu related but what is the difference between an adsl router and an ethernet modem?
View 5 Replies View RelatedSince this is my first post, before i describe my problem, i'd like to say regrats to all of you for maintaining here such a good support community.
So, here we go: I have a headless Debian box and i want to set it up as a small office router/gateway. On the box i installed a regular NIC and a Viking Traverse ADSL+ Card which gets recognised by the OS as an 8139 ethernet card and has an embedded ADSL+ modem. The modem is accesible through the PHY interface once it gets assigned an IP. Having said that here is the actual setup:
eth0 : Viking Card
eth1 : NIC (this NIC is connected to a switch)
eth0 : 192.168.1.2 (internal modem is on 192.168.1.1)
eth1 : 192.168.1.3
/etc/network/interfaces
[Code]...
Does anyone have an opinion on the BELKIN F5Z0142uk Enhanced Wireless ADSL Router Network Kit, I want to setup a small home LAN and this kit caught my eye, it includes a usb Wi-Fi dongle for connectivity to a desktop computer, one of my pc's doesnt have a network card so this sounds like a good idea. Whats the build quality like and is it reliable. The link: [URL]
View 2 Replies View RelatedWhat are the pros and cons of various current model ADSL modem routers for use with DD-WRT, OpenWRT or Tomato? There are, of course, hardware compatibility lists (HCLs) for each of these (DD-WRT, OpenWRT and Tomato) but many of the models are no longer available and there are so many that researching them all would be onerous. Many pages on the Internet recommend the WRTG54L and that would be great but it is no longer an option except second user which is increasingly difficult. What are the pros and cons of the various chipsets: ADM5120, AR7, IXP4xx and BCM63xx?
View 4 Replies View RelatedI use a wired Dlink Adsl Router GLB502T with its inbuilt dialer configured. Problem is it will not connect while computer is running.When I try to ping the local ip of the modem this is what I get "ping: sendmsg: Operation not permitted" and "/etc/init.d/networking restart" has no effect either.I need to restart my computer every time i want to connect to the Internet.I switch on the modem when the grub bootloader appears and the modem connects without any problem.This problem appeared when i installed Ubuntu 9.04.There was no problem with Ubuntu 8.04.
OS:Ubuntu 9.04
Motherboard: Asus M2N68-AM
NVIDIA Geforce 7025/nForce 630a
RTL8211CL Phy Gigabit LAN
[code]....
I have 2 pcs at home. I dont have a switch so I can connect only one PC at a time to my adsl router/modem for internet access. In the past I had successfully connected the two PCs (NIC to NIC) to each other using the same ethernet cable which was supplied with my dlink adsl modem.
Recently the motherboard of on of my PC went bad so I replaced it with a new one. The problem is when I connect the two using the same Ethernet cable they won't connect. The lights on the Ethernet port won't light up. I can still connect both of them to the adsl router (NIC to Router) (one at a time).
I want to configure my ADSL but I don't know what should I do. Can you explain me How can I configure it?(I use fc10, ethernet cable <Asus Am608 ADSL modem)
View 9 Replies View RelatedAfter reinstall Ubuntu 10.04 LTS didn't recognize my ADSL router Billion 400 G.The Ethernet 1 led is off after booting.Search on web for help on this but no good results.You good people now are my last resort.I tried boot in live CD and result is the some.Check with sudo lshw.
View 9 Replies View RelatedI'm going to set up a new linux router for a company, and have to set up bandwidth throttling. They have an unlimited ADSL internet connection which will be shared between 2 businesses, one being them. I will need to set it up so their connection will never be slowed down by the other business. They will both be connected to the same NIC, but will be on different subnets. How would I go about doing this?
View 2 Replies View RelatedThe router should handle everything automatically and transparently. All you need to do is make sure that the wireless Ethernet adapters in the laptops can "talk" to the wireless router.
View 4 Replies View Relatedi need to connect to the internet with my huawei smartax mt880 adsl router from a linux redhat 9 box ,
- I can get into the router as user admin / admin at address 192.168.1.1
- I get missed in between pppd setup & my kernel modules insertion . . .
- can I find a clear step by step guide to get me connected to the internet ?
Using SuSE 11.2 can anybody suggest a decent compatible Ethernet / Network Colour Printer. Just a printer not a multifunction device. The printer will be connected to a Fast Ethernet Switch or directly into the ADSL Router.
View 4 Replies View RelatedMy router/adsl modem is not connected to a power supply so when power goes and comes the network will do a re-boot. Now the problem is my OpenSUSE network won't come back on! I set the static ip as Autoeth0 to eth0 however when network updates I losse eth0. Why is this happening? Why doesn't the PC simply re-connect? Can I do it via command line?
View 5 Replies View Relatedrecently I have installed a suse 10 sp2 on my computer. I have a big problem about connecting to my ADSL Router. The problem is that I can't ping the router at all and the Kinternet log is prompted that
status is: disconnected
trying to connect to smpppd
connect to smpppd
Status is: disconnected
error: cannot read real interface for eth-bus-pci-0000:04:00.0
I can easily open the web page of my router with windows OS but in the suse I can not do that with firefox.
I have an adsl modem acting as a bridge to my router my setup was working well for more than year now , but then the internet went slow . I set the modem back to PPPoE the problem was with the DNS server of the ISP so using ifup i set the dns t 8.8.8.8 (google) the connection is back , but when i set the modem back as a bridge slow internet does the router know that my dns is 8.8.8.8 or i should set the dns on the router ? I can't see an option to set the dns on the router ( i just enter my username and password from the isp to use PPPoE mode ) by the way i called the isp support they kept telling me to restart , i told them i did but i never restarted my pc . I'm sure if i tell them i'm running linux they will blame the os !
View 2 Replies View RelatedAt home, I have one pc and one laptop. The first one is working under Windows XP and connected to ADSL. The second one is under dual boot : xp and ubuntu. Some months ago, i've created an ad hoc network so that i can share the ADSL connexion with the laptop. When the laptop is working under XP, it works. But when i'm on ubuntu, the network is detected - i guess it is detected as a ad hoc network, cuz it's represented with two computers - but the ADSL is not shared. What do i need to change?
View 1 Replies View RelatedI just switched from windows to lucid lynx 10.4, but I am really frustrated because I have no idea about how to set up Internet (both adsl and wifi). I have checked the documentation and browsed for hours but the solutions out there never seem to apply to my case, so I beg for some personalized help on how to set up Internet. The only things I know are how to get to the terminal and that I am on an HP laptop. I beg you if you request information you give me a hand at how to find it, given my inexperienced level
View 3 Replies View RelatedI have an ADSL Internet connection with static IP.I connected through PPPOE from my modem to my ISP.I need to ssh from outside of my home to my home, But i don't know to use which connection between my computer and my modem.(dhcp ,static , bridge or ....)
View 1 Replies View Relatedis possible to use linux (especially slackware) to bond 2 (ethernet modems) adsl connections. For example if i have 2 connection of 24mbs download and 512 upload i will create achieve 48 mgps dowload and 1 mgps upload . something like that
adsl1 modem <------ eth1--- (slackbox router) --- eth0---> my server
adsl2 modem <------ eth2----
I have an ADSL line that allows me for maximum of 4 concurrent users with external IP addreses. The IP addresses are not static (they change every 3-4days).
My current setup is as follows:
* A-link Roudrunner 44B Modem connected to the main line
* D-Link DI524 Router (port 1) connected to the modem
* This leaves me with 3 ports and Wireless for my other machines
What I wish to do is:
* Have all my machines with static IP addresses for LAN
* still have internet connection
I've tried enabling DHCP on the D-Dlink Router with LAN IP 192.168.0.1 and IP range from 192.168.0.100 - 192.168.0.199. Then gave my machine static IP 192.168.0.101, subnet 255.255.255.0 and gateway 192.168.0.1....obviously it didn't work. I've tried the above with both the modem being connected to the router via port1 and WAN port... but I have the same results. I also tried to do the same without the router (direct connection between the PC and modem) still got the same results. Could it be that what I am trying to do is not technically not possible due to my ISP setup to ensure no more than4 concurrent users limit is in place.
Q: How can I use at the same time two ADSL USB modems with pppd and pppoatm.so plugin?
I have the following scenario:
- Two ADSL USB modem correctly recognized by Linux.
- pppd configured with two different files, one for each ADSL (even if the two ADSL have the same parameters). Those files are /etc/ppp/peers/adsl1 and /etc/ppp/peers/adsl2
If I attach only one modem and then launch "pppd debug call adsl1" or "pppd debug call adsl2" everything works fine.
If instead I attach both modem in order to have two ppp interfaces, ppp0 and ppp1 I get the following behaviour:
- When launching "pppd debug call adsl1" the first modem connects correctly.
- When launching "pppd debug call adsl2" I get:
connect(8.35): Address already in use
That's because either adsl1 and adsl2 are trying to use the same modem.
So the question more specific question is: How can I specify which USB modem to use in pppoa ADSL connections?
With dialup modem it is possible to specify /dev/ttySx in peers files, but what about ADSL USB modems?
I want to set up a Linux box as a wireless router to replace our existing Netgear WNR1000 router, as I believe the Netgear does not support the coming IPv6 protocol. Unfortunately, it is not flashable with OpenWRT or DD-WRT presently.
As we have Comcast, our cable modem acts as a dumb modem according to the customer support guy I talked to, and our router is the one that asks for the IP address from DHCP. Thus, when Comcast switches over to IPv6, I don't believe my existing router would work, correct?
My idea is to take a Linux box and put two NICs and a wireless adapter in it, using IPCop or Smoothwall to set up a router. I could then enable IPv6 support for when we have IPv6 with Comcast. Is that possible? Would there be a way to get BIND to hand out private IP addresses in the same subnet on the both the LAN NIC and the wireless card?
I'm having trouble getting my network set up the way that I want it/had it. You see, when I first set up my network, I just had my cable modem going directly to my standard wired router (A D-Link DI-604), which had DHCP,and was connected to all of the computers on my network. I had one switch hooked up to one of the ports of the router, but this was a regular switch, and it would not try to assign IP addresses, it would just pass through the DHCP info as I wanted.
Now however, my network setup has changed. My room mate and I both got laptops, and we decided that we wanted to have wireless access so we didn't have to constantly plug in to the router.
Now my network is set up like this: The modem is hooked up to the router(DI-604), which is hooked up on the LAN side to our computers, our switch (which is hooked up to 3 more computers), and to a wireless router card (A Gigabyte GN-BC01).
The wireless router card has two jacks for ethernet. One for WAN, and one for LAN. The LAN side we have plugged only into the computer in which the card is installed.
Now the problem is this: The wireless router card comes with DHCP by default, and it's assigning addresses to the laptops and to the computer hat it's in, and worse, the IP addresses are on a different subnet than that of the main dlink router. The Main (dlink) router assigns addresses from 192.168.0.1 (itself) to 192.168.0.254, while the wireless router card assigns addresses from 192.168.1.1 to 192.168.1.254 (itself).
Because of this, I cannot access services on the wireless network from my wired network or vice versa. The first thing I tried was setting the card to assign addresses from 192.168.0.12 to 192.168.0.253, however it just said "internal error" when I tried to do this. I decided that this may be because it sees that it was being assigned an address on it's WAN side on the same subnet. So the next thing I tried was disabling DHCP and setting the "LAN IP Address" to 192.168.0.12, hoping that the DHCP would just go through the card, like a switch. I would have set the LAN IP address to be assigned by DHCP, but this was not an option, so I decided that'd be the best thing to set it to.
Once again however, setting the LAN ip address to an address on the same subnet as that of the IP assigned to it's WAN side caused it to report an "internal error". I verified that this was the issue by setting the LAN address to several other private IP addresses to test (I.E. 10.0.0.1, 192.168.3.1, 192.168.5.12).
My question then really is: How do I set up both routers so that I can access services and computers from each network from the other network. Should I set them with different subnets and set the gateway on the wireless network to the main router? To the wireless router card? Should I put them on the same subnet? Will it know how to communicate?
Here is a link to (picture) my network diagram. Network Diagram
I'm using ADSL connection as a way to access internet.All of us know that in windows we can get configed easily.But it is a little more difficult in Fedora.How can we config ADSL connection in Fedora 10?My modem uses dynamic ip.
View 14 Replies View RelatedI have an valid account,and I used pppoe-setup to set the dial correctly.After the configuration,I typed "ifup ppp0",nothing wrong happens(no news is good news?).Then I typed "pppoe-status",it said I've connected to the internet . I opened firefox,updated my system through yum ,they all said I haven't connected to the network!!!I've formated my harddisk and reinstall my system,but the problem is still.
View 4 Replies View Relatedis there any problems with making adsl connection in ubuntu 10.10. Recently I've had ubuntu 10.04 and there was a problem with making adsl connectio so I was forced to you terminal in order to connect to internet. I'm asking you this because I'm planing to install Ubuntu again but if there is still connection problems then I wouldn't install ubuntu
View 5 Replies View Related