Hardware :: SATA Error -> Sys Hard Reboot On Suse 11.3. Board + Hdd Changed - Error
Feb 1, 2011
i actually registered here because i'm done with my knowledge of linux, errors which cause my sys to hang and/or reboot randomly after some time. They occur while the system is under heavy cpu, heavy mem-read-write, mediocre mem fill, heavy hdd io (for ~20 seconds every ~5 minutes).
problem background we ordered two identical PCs (specs below), one of them brought those sata errors quoted below from /var/log/messages, the other one runs flawlessly. Same Hardware and Software Configuration. Faulty one brought reallocated sectors right at start, mass seek errors, read errors. 1st try: swap cables, change bios mode ata_piix <-> AHCI. Didn't work. Went away for repair. Stupid Techie did only swap hdd, so problems occured again. Shipping for repair again. Board AND hdd exchanged. no more seek/read errors, no more reallocated sectors. But similar sata problems right after 3 days of previously described workload. Following logs are from after the last repair.
[Code].....
View 7 Replies
ADVERTISEMENT
Sep 1, 2009
We have a server running suse 9. I had to do a reboot yesterday. the server dropped off the network, but did not reboot. It was attempting a connect, but I don't know why or to what. These are the lines that I saw on the screen:Connecting to (DESCRIPTION=(ADDRESS=(PROTOCOL=IPC)(KEY=EXTPROC1) ))
View 1 Replies
View Related
May 1, 2011
I keep getting this error in my log viewer every 2 seconds: Code: ata4: limiting SATA link speed to 1.5 Gbps I have a dual boot SSD and I have run many SMART tests in windows and linux, (using smartmon tools and the disk utility) and the reports are all 100% healthy..... My research shows that this error represents one of the following:
1. Problem with SATA controller
2. Changing BIOS to allow SATA
3. Changing SATA mode to PATA or AHCI
4. Replacing the SATA cable
5. Allowing the SSD to run at SATA II speeds, i.e. 3 Gbps
- Does anyone know how to try number 5, i.e. allowing the SSD to run at SATA II speeds? I am lost here and this problem has caused my machine to crash twice when watching a movie in linux/ ubuntu. (It is worth noting that the crashes have only occurred in linux and I have never had an issue in windows, so it does seem to be a linux setting somewhere, hence why I think it is a "allowing SATA II to run at correct speeds issue")
View 4 Replies
View Related
Jan 15, 2011
When I try to connect to my SUSE server from other one this appears: Remote host identification has changed. I deleted entry in know_hosts but it still working wrong, showing me this message. What could be the cause of this problem??
View 1 Replies
View Related
Aug 13, 2010
Can SATA 3 (SATA III) Hard disk be run on motherboard which only supports SATA II, except sacrificing the speed (throughput)?
View 2 Replies
View Related
May 4, 2011
I'm working with Linux 2.6.23 on an embedded device and am receiving the following error executing the reboot command.
View 2 Replies
View Related
Mar 8, 2010
I changed my keyboard language. Then restarted without changing it back to English. My user name and password is in English. I'm using a custom GDM theme. Now when i switch on my system my login screen keyboard language is not English. what can i do? Is there any way to change it back?
View 2 Replies
View Related
Oct 7, 2010
I am using sda1 as /, which is a bootable drive. I do not know if my problem is that I did not create a /boot drive. After removing the iso dvd, I tried to reboot and I get this back: -bash: /sbin/reboot: input/output error Then it returns me to the terminal prompt.
View 6 Replies
View Related
Aug 6, 2010
I'm looking for doing AOE (Ata over ethernet) inexpensively with single board computers, like Routerboard stuff, but is there anything with sata plugs. Hopefully I can get each board for hopefully around $50, but a little more would be ok. Non-x86 is fine, Debian is as good as Ubuntu.
View 3 Replies
View Related
Jul 22, 2010
I am running memory test on SUSE, Memory test is just writing some patterns into a memory and reading it back in all CPU threads. After a while, when memory test is running in the background , I am trying to reset the system by echo b> /proc/sysrq-trigger command, Upon SUSE warm reset , I am seeing some UNCORRECTABLE MEMORY ERROR in model specific register (MSR : 0x421),
I am seeing this behavior on one of my server which has huge amount of memory.,Have you ever seen this UCECC error when SUSE generates warm reset when memory test in the background ?
View 4 Replies
View Related
Oct 13, 2010
PackageKit Error repo-not-available: File '/repodata/repomd.xml' not found on medium 'http://download.opensuse.org/repositories/KDE:/KDE4:/Community/openSUSE_11.2/' My 11.2 won't update and gives this error. Anyone know how to fix it?
View 2 Replies
View Related
Feb 28, 2010
I have read others getting Grub error 2, but i cant fix the problem. I have 2 sata HDDs. I suspect the problem is something to do with RAID?
View 2 Replies
View Related
May 6, 2011
I experienced a strange random error that appears to have been my PC losing contact with the PC's 1.5 TB SATA drive.
This happened once (thus far only once - about two hours ago) on my Intel Core i7 920 PC with a Asus P6T Deluxe V2 mother board running openSUSE-11.4 with KDE-4.4.4. A reboot failed to fix the problem but a cold shut down restart did.
Some details ...
I had a zillion apps open, connected to my mother's PC in North America (from here in Europe) using vnc, had thunderbird, firefox, many konsole sessions, and various leafpad editor sessions.
Firefox appeared to hang, so I tried to close the Firefox page, but the PC appeared frozen (although the mouse would move). Then after about 60 seconds, the screen flashed, firefox closed (crashed may be more accurate) and I had my desktop back, ... sort of .... And I was able to go to the desktop area where vnc was running and access my mother's PC. But I was missing almost all the icons off my KDE destkop and most the icons off the panel at the bottom of the desktop.
I tried going to <CTRL><ALT><F1> and then <CTRL><ALT><F7> but that made no difference. I tried going to <CTRL><ALT><F1> to login but it would not let me login as a regular user, nor as root. Nor could I ssh into the PC. After <CTRL><ALT><F7> back at the crippled GUI, I typed 'shutdown -r now' (as root) but the command was not recognized. Neither was 'top' (as a regular user), nor 'fdisk' (as root). Dir was recognized as a regular user as was CD. But I did not believe the information those commands were giving me (it did not appear up to date).
Eventually I killed X with <CTRL><ALT><Backspace> (twice) and then forced a shutdown start with <CTRL><ALT><DELETE>, but then the PC hung during the shutdown, with the hard drive light on solid. That never happens. After a minute of that I decided to hit the 'hardware' reset. The PC restarted, but was incredibly slow to go through the motherboard boot menu's and it reported the hard drive not detected and would not boot. I did a <CTRL><ALT><DELETE> to restart, and pressed DEL to go to BIOS, and then noted in BIOS that the SATA drive was not detected.
I checked the temperature and the PC was a nominal cool temperature (38 to 40 deg c).
I then switched OFF the PC. I also turned the OFF switch on the back OFF for good measure. I waited a minute. And I turned ON again the PC.
The PC booted normally as if nothing had happened.
Most bizarre and a bit of a fright. My Linux is usually rock solid.
Anyway, ... no more investigation for now. I'm doing a massive backup of all data since my last backup. This will take a while as I have about 400 GB of home movies (at various stages of processing) from my home video camera to backup to an external hard drive.
I may pickup another 2TB external drive this weekend, just to ensure I have multiple backups.
View 5 Replies
View Related
Jul 29, 2009
I've installed CentOS 5.3 in a new machine....
But i got these errors when kernel is loading
The machine is a dual core 2.6 Ghz, mainboard is intel DG31PR, SATA disk SAMsung 500 GB, 4 GB RAM.
I've checked other errors in different distributions, but everyone has a different criteria about the problem.
View 5 Replies
View Related
Nov 19, 2010
I am having DM6446 board. I am trying to connect internet via this board. In this I am having some issues regarding this. Normally in terminal when I ping to particular site, I will use the following command
>> ping google.com
I will get proper response with the packets details. When I am trying the same thing in minicom terminal I am not getting anything even the proper error messages. If I use the same ping command in different way
>> ping 209.85.231.10(ip of google.com)
I am getting proper response. I don't know why the DNS name is not resolving in the board. Is there any documentation is available to do the internet connectivity with this board?
View 3 Replies
View Related
Feb 9, 2011
I don't know if this the right place to ask this question. If not excuse me.I installed apache server on my ubuntu and I've changed the www folder in etc/apache/.../default from /var/www to home/user/www but now i haveForbiddenYou don't have permission to access / on this server.
View 3 Replies
View Related
Aug 1, 2011
sudo still works, but every time I run it, it says it's unable to resolve the host. I tried to change stuff in visudo, but there wasn't anything about the host as far as I could tell.
View 9 Replies
View Related
Jul 31, 2010
We have a Wipro Net Power 8552 server on RAID 5 with Linux Advanced Server. The Databse is Oracle . Every time the reocovery is made the block corruption error gets changed. There are four hardisk in the Raid with 18 GB capacity of Quantum make. I want to make sure if any Utility is there in Linux to check the Harddisk if any Block corruption is there or Not.
View 1 Replies
View Related
May 28, 2011
ubuntu 8.04 server can not detect seagate sata hard drive 2tb or sata Lg dvdrw x22 sata drive .is it possible to install it without buying a pci ide sata card?is it possible to get a driver for sata driver and sata drive that can be recognise by ubunto 8.04 server ?or to get the files for 1.44 floppy diskdoes the late edition of unbutu recognise sate hdd and sata cdrw drive automaticly during the installation of the unbutu?
View 1 Replies
View Related
Nov 9, 2010
I've installed debian squeezy recently and for some reason I have problems with mounting /home partition during startup.
There's an error:Mounting local filesystems...mount: special device /dev/mapper/isw_bbfedcffgi_Volume0p6 does not exist. failed
I've tried using fsck - no result the file system is healthy, I've tried formatting it once again (fresh copy, no user data) and it's not working. What is more mounting the partition manually goes well - I can read the data and write to it. All other partitions are ok.
I have no idea what's going on and why mounting /home fails. I've written this post on Polish debian users forum, but no response - only to give more info, so I'll put it here also:
ls -al /dev/mapper
crw------- 1 root root 10, 59 Nov 9 19:34 control
lrwxrwxrwx 1 root root 7 Nov 9 19:34 isw_bbfedcffgi_Volume0 -> ../dm-0
lrwxrwxrwx 1 root root 7 Nov 9 19:34 isw_bbfedcffgi_Volume01 -> ../dm-2
lrwxrwxrwx 1 root root 7 Nov 9 19:34 isw_bbfedcffgi_Volume05 -> ../dm-3
lrwxrwxrwx 1 root root 7 Nov 9 19:34 isw_bbfedcffgi_Volume06 -> ../dm-4
code....
View 2 Replies
View Related
Apr 2, 2010
I installed debian 5.0.4 server on a PC that has both IDE and SATA controllers. I used an IDE HD to install the OS. The input device was a USB DVD unit. The IDE drive showed as /dev/hda and the 4 SATA HDs showed as /dev/sda1, /dev/sda2, /dev/sda3 and /dev/sda4. After the OS was installed the reboot started which brought up an error: GRUB GRUB Read Error
I then disconnected the SATA HDs and rebooted successfully. So no PROBLEMS with just the IDE drive connected, grub works fine. If I reconnect the SATA HDs though grub fails with:
GRUB GRUB Read Error
The problem originated when the installation got to the GRUB implementation. Here the installer engine asked me If I wanted GRUB to be installed on the MBR, to which I said YES. The installer had listed the IDE drive (/dev/hda) before the SATA drives (/dev/sda, /dev/sdb, /dev/sdc, /dev/sdd). After the installation finished and the machine was restarted, BIOS looked at the SATA drives first could not find the grub stages and it displayed an "Read Error".
After realising what was happening I looked at the BIOS settings to see if the HD booting sequence could be altered. The BIOS did indeed list the 4 SATA drives first and the IDE HD last. BUT it would not let me alter the booting sequence. So I was stuck with what the BIOS doing. So I decided I take the IDE drive out and create a 20G partition on the first SATA to accommodate the OS. So now everything works OK.
View 2 Replies
View Related
Mar 3, 2010
It seems I can't burn any kind of disc (cd/dvd, audio/video/data) usgin my internal sata burner (sr0). I treied googling around and reinstalling everything from dvd+rw-tools up but the error is still there. the burner works fine with windows on the very same pc (dual boot). I tried different media and different speeds. when using an usb burner everything's fine...
[Code]....
View 5 Replies
View Related
Sep 19, 2009
I am using Fedora core 10. I have changed my partition size of Linux from windows. After I finished resizing the partition, I rebooted my system to the Linux platform. While booting it gave me an
error: repair filesytem #1:
I don't know what to do?
View 5 Replies
View Related
Mar 1, 2010
I want to stop using Windows because it sucks so i have downloaded all kind of distibutions from Linux. They give all the same error because it seems Linux has problems with Fakeraid. Now i have running OpenSuse in VmWare 7.0.1 but i want it as the only OS.
The installation goes fine but in the end it gives a Grub error because it cannot create the bootloader. It seems to be a common problem and i have done all the steps that i could find on Google.
I have two raid controllers. One is integrated in the mainboard from Asrock ALiveNF7G-HD720p R5.0 and OpenSuse sees it as a Jmicron controller.I have bought also a EM2001 2 Poorts PCI Controller SATA card with two harddisks in Raid 0 because Linux failed to install on the JMicron. On the EM2001 2 Poorts PCI Controller SATA it also fails with the same error.
I want OpenSuse 11.2 working on Raid 0. I know it must be some simple commands in the terminal through a live cd to correct the bootloader and do it manualy by Linux users but i'm a Windows user.
Can somewhone please tell me the exact steps and commands to install Linux on Raid 0 Fakeraid?
View 4 Replies
View Related
Mar 18, 2010
I have an SD-VIA-1A2S PCI card with 2 sata ports (and one ATA-133 that isn't used). Two new Western Digital Caviar Green drives (WD10EARS 1TB) throw repeated errors in kern.log (removed date/time/host info for brevity):
[ 7.376475] ata2.00: exception Emask 0x12 SAct 0x0 SErr 0x1000500 action 0x6
[ 7.376480] ata2.00: BMDMA stat 0x5
[ 7.376483] ata2: SError: { UnrecovData Proto TrStaTrns }[code]....
I'm using Ubuntu 9.04 - 2.6.28-18-generic, though I have tried live cds of Ubuntu 9.10, Fedora 12 and OpenSUSE 11.2 - all running various 2.6.31 kernels - and all received the same error.Based on testing these drives and this card in two other machines and combos of connecting the drives directly to the motherboard or the add-in card, I'm relatively convinced that it's the VIA chipset that is the problem.Another computer that also has an onboard VIA SATA chipset (like the add-in card) produces the same errors when the drives are directly on that motherboard. I have been able to verify that the drives are perfectly good, and I tried everything I can think of in terms of swapping cables, psu isn't overloaded, etc.
The error happens on boot once or twice, after using fdisk on the drive once or twice, and constantly when attempting to sync a new mdadm raid 1 array created on the two drives.I'm completely open to buying a new PCI add-in card if someone can recommend one with 2 internal sata ports that works well in Debian/Ubuntu.
View 2 Replies
View Related
Mar 20, 2011
I tried installing Red Hat linux on my Sata hard disk . As soon as the hardware detection phase starts it generates the error "No hardware detected".roblem? (I have also tested RHLE 5, CentOS 5.4, but none of them detect the hard disk and I can not install anyone).I have installed Windows 7 on one of my disks and I have not any problem with it.I also changed storage configuration in Bios as AHCI, IDE,
My Hardware config is as below:
Mainboard: ASUS P6X58D premium,
CPU: core i7 950,
HDD: two 1 TB WD SATA3
Ram: 6 GB (3*2 GB cruciall[/U][/U][/B]
View 4 Replies
View Related
Nov 4, 2010
I have a disturbing problem with my monitor which goes to sleep (or ??) after few minutes if my comp is not used and most of the time I have to restart my comp.I disabled everything in Powersave , but nothing. I did have that problem in previous versions of SUSE, but somehow, I solved that. I cant remember what I did then.
View 4 Replies
View Related
Mar 17, 2010
I am having following problem. If I try to change my SMB password, it throws following error >
Quote:
~>smbpasswd
Old SMB password:
New SMB password:
Retype new SMB password:
Server did not provide 'target information', required for NTLMv2
rpc_pipe_bind: rpc_send_auth_reply failed.
machine 127.0.0.1 does not support SAMR connections, but LANMAN password changed are disabled
Failed to change password for user1
View 1 Replies
View Related
Feb 4, 2011
We have an external raid box connected to a debian squeeze server.Every new volume set I have created will be detected (as /dev/sdx) after a reboot. As this is our file-server I cannot reboot the server every-time a new volume set is created.Is there a way to make this new device visible.I tried already 'partprobe' and restarting udev didn't work eather.What is a good way to do this?
View 3 Replies
View Related
Jun 6, 2010
Just done my first ubuntu 10.04 install on a hp pavilion a320a, the install seems to have went well, though while it is shutting down and before rebooting the following error appears across the screen:
[16866.760778 end_request: I/O error dev sr0 sector 504392]
Before this error appears at the bottom of the screen the error scrolls on the screen with a different number at the beginning of the error where 16866 etc (different number each line) remainder of the error remains the same maybe different sector number but not sure, there is way too many to write down in the time they are on the screen.
View 7 Replies
View Related
