Hardware :: Installing RAID0 With Fedora6?

Mar 23, 2010

Im trying to set up two raptors (identical) with RAID-0 using Silicon Image.

The drives arent being detected by linux. I have the linux drivers on USB but unsure on where to install them. There is no option available...

The drives are being detected on computer start up..and were working with windows...

Havent tried a diff distro as can get my hands on one.

Motherboard is a A8N-Sli Deluxe.

View 5 Replies


ADVERTISEMENT

General :: Installing On An Existing Windows RAID0

Dec 19, 2010

I administer a small network of computers connected to a windows 2003 server. The machines Dual boot Windows XP and CentOS 5.

My question is this. The machines are being upgraded to HP Z800 workstations. These workstations come with 2 1TB drives setup on a hardware RAID0. Can I install Linux on these machines, using the RAID0? Can I do an install as if it was just one hard drive? The machines came with Windows7 and I'd like to keep it intact including the RAID0. Can I do the install where it resizes the partition, adding the linux partition to the "drive".

If I can't use the existing windows RAID0 to install CentOS I was thinking of just installing another hard drive in the machines for it. This brings up another question, what would happen if I moved my Linux drive from one of the old workstations and put it in the new workstation, would it boot? I know windows wont boot like this because of the hdd controller drivers and I have a sneaky work around for this anyway but am not wanting to transfer the windows installation.

View 5 Replies View Related

CentOS 5 :: Installing On A Existing Windows RAID0?

Dec 20, 2010

I administer a small network of computers connected to a windows 2003 server. The machines Dual boot Windows XP and CentOS 5. My question is this. The machines are being upgraded to HP Z800 workstations. These workstations come with 2 1TB drives setup on a hardware RAID0. Can I install Linux on these machines, using the RAID0? Can I do an install as if it was just one hard drive? The machines came with Windows7 and I'd like to keep it intact including the RAID0. Can I do the install where it resizes the partition, adding the linux partition to the "drive".

If I can't use the existing windows RAID0 to install CentOS I was thinking of just installing another hard drive in the machines for it. This brings up another question, what would happen if I moved my Linux drive from one of the old workstations and put it in the new workstation, would it boot? I know windows wont boot like this because of the hdd controller drivers and I have a sneaky work around for this anyway but am not wanting to transfer the windows installation.

View 2 Replies View Related

Ubuntu :: Data From Windows Raid0

Oct 21, 2010

I had windows and ubuntu for some time, the other day I had an issue with (msconfig). The easiest way to fix it is to fresh install windows. So I wanted to boot into ubuntu, take my windows files and toss them onto a external drive. So this is were I need help. I have 3 hard drives, 2 internal and 1 external. The 2 internal drives are 2 500 gig WD's in raid0. I can not find out how to retrieve my data from these drives at all. I can get the partition manager to tell me I have them, but I can not find them anywhere let alone get data off. And I have my work for my 10 page research paper on there and I should be working on it but have not been able to retrieve the work and put it on my laptop.

View 5 Replies View Related

General :: Where Is Uuid Of Partitions Of Raid0

Sep 4, 2010

where is uuid of partitions of raid0?

My box is centos 5.4 x86, and dual booting with windows 7. I need to make a ext3 partition between ntfs partition 2 and 3.

After making this ext prtition, I need uuid of this ext partition.

View 1 Replies View Related

Server :: Adding Raid0 To Slackware 13.1

Jul 1, 2011

I'm an experienced PC technician running a slackware 13.1 distro on a server at home. I've currently got 2x 1TB drives in the box allocated as raid1 for the OS and everything I want to run on the machine. I'd like to think my question/needs are fairly straight forward, I am buying 2x 2TB drives to add to this machine as it serves as a NAS box for one of its roles. I'd like these in raid0 as the data that would be going on it is not that important to me. The question is, after adding the new drives to the system, once I boot up, what do I need to do to the system to get the drives added and working sucessfully as a single raid0 volume that I can then samba share out to my network. To clarify, I understand a little of mdadm as I've used it to raid1 my existing setup when I installed, and I'm fine with the samba bit after.

View 5 Replies View Related

Debian Hardware :: LVM - Performance Between A Raid1 And A Raid0 The Same

Mar 21, 2010

I just have a few questions about LVM and RAIDs. It seems they are basically the same thing. Is this correct? I can add two drives together on both of them and it appears as a larger drive, along with other setups like raid1 and raid5, etc.. And is there a difference in performance between them?

And my second question.. I know one is stripped and one is not, but is the performance between a raid1 and a raid0 the same? I've been told that raid1 is faster than raid0 because the data is written twice.. and therefore can be read from two different disks which equals faster read speed, but slower write speed since it writes to the two.

View 1 Replies View Related

Fedora Installation :: 11 Can't Install On Software Raid0

Aug 31, 2009

Because of all the trouble with the asrock 939SLi-eSATA2 (see my previous unsolved thread) I have bought a new MSI 790FX-GD70 mobo + processor +ram3 memory and shifted my MSI K9N2-platinum to the asrock box and mothballed the asrock mobo. A rigorous way to solve the problem, but it turned out to be the beginning of more severe trouble. When I try to install Fedora on the striped disks at first everything looks good. Both gparted and the installer see the linux device mapper partitions on the raid config + the unused space.But if I tell the installer to use the unused space, a mere 150 gig, then it tells me:

Could not allocate requested partitions: not enough free space on the disks. The same happens if I try the custom layout. When I start with a small 200 mB ext3 boot partition the same message appears.The ubuntu live cd with dmraid installed and the ubuntu alternate cd do not even see the devmapper partitions. Is the AMD-ATI chip on this new mobo not properly supported by Fedora/Ubuntu?

View 2 Replies View Related

Fedora :: Run 12 X86_64 On 2x500GB RAID0 Setup?

Apr 13, 2010

I want to run Fedora 12 x86_64 on my 2x500GB RAID0 setup, how would I do this via the BIOS method (I want to dual boot Win7 off the same RAID array) with an AMD SB750 southbridge? I'd prefer not to go software, but if I have to I can and just use the 1TB for 7. (I'd prefer not to as the 1TB is a hotswap drive, mostly from PC to External case)

Note: I don't actually have the 1TB Hard Drive or BluRay drive yet, they're still on order)

I searched, but all the results were for Intel's ICH10R or SB600, computer specs are in sig, if there's anything else just say.

View 6 Replies View Related

Fedora Installation :: 13 - Raid0 - Graphic Card Or Something Else

Oct 11, 2010

I've already got two installs without much problems.. one on my laptop and another fedora13 install on an older comp just to test it a bit before installing it on my main comp. But now I've got a problem. Both those install went without problems but when I started installation on my main comp first I've noticed some graphic problems when there is installation started and there is mouse and fedora 13 welcome installation screen. there are some like glitches or something no idea how to describe them.. like bad pixels in small upper part of the screen. But ignoring that everything went OK up to the part where I can choose a standard discs or non starts like sans and stuff..

When I choose standard disc installation just freeze there. No idea what is happening. Only this that came across my mind is that there is a problem with raid maybe? There are 2x640Gb HDD in raid0, there is win7 installed, and another 1Tb HDD, non-raid member disk, where I would like to install Fedora and have a dual boot. Still got programs that I need win for I'm afraid. Installation went smooth on laptop and another comp but there is no raid so I'm guessing that could be a problem. This comp where installation froze is in short:

[Code]....

View 2 Replies View Related

Ubuntu :: Setup A RAID0 Arry Using The Beta Of 10.04?

May 8, 2010

I used Palimpset to set up a RAID0 arry using the beta of 10.04. I, being the neat freak that I am, like to do a clean install between betas and final releases. So I backed up all my photos and such to that RAID array (this is on my home server/desktop, by the way) and reinstalled (using the final Ubuntu Server 10.04 disk). When I was re-installing, I stupidly created (but didn't format) a new RAID array over the one with my data on it. Now I'm back on the final Ubuntu Server 10.04, and palimpset recognizes that theres a RAID array, but says its unformatted.

View 4 Replies View Related

Ubuntu :: Btrfs Raid0 Won't Mount At Boot?

Jul 15, 2010

I upgraded my 9.10 installation to 10.04 and decided to try out btrfs on a some spare drives in the system.sudo mkfs.btrfs -m raid0 /dev/sdb /dev/sdc /dev/sddthe only way the system sees the btrfs array is by running btrfsctl -a and then mounting /dev/sdc. but that has to be done in userland, not at boot. if i try to mount it via fstab, ubuntu won't load because it can't find the mount point./dev/sdc /Images atasum,thread_pool=128,compress,rw,user 0 0so where am i going wrong? I tried mounting via the UUID also but that didn't seem to work for me either.

View 1 Replies View Related

Ubuntu :: Accessing NTFS Raid0 In Kubuntu

Jul 15, 2010

I just encountered a huge problem with my PC. It's a Sony VAIO VGC-RC210G with the first two HDDs in a RAID0 configuration. Windows Vista is installed on the RAID and Kubuntu on another HDD.We had a power outage yesterday and the PC was powered on. Vista wouldn't boot, something which I traced to crcdisk.sys (stupid f***ing CRC check)

View 1 Replies View Related

Ubuntu Installation :: Wubi On Windows With RAID0

Feb 1, 2011

I am trying to install Ubuntu 10.10 using Wibu inside Windows and installation looks good without any problems but when I select Ubuntu in Boot POST menu after I see Ubuntu Desktop I see error it's saying that Root directory is not specified and there is OK button and if I press it I see same message. only way to get out is to click restart in top right corner. My Windows installation is on RAID0 SSDs and I actually tried to install it on same partition as windows and even tried to install on NEW unallocated and freshly formatted partition. Nothing works. I am thinking to install it from Live CD however in advance formatting on let's say 20gb of space what do i assign ? Like how do I partition it like root directory and swap and other partition i ll need. Like can you specify all I think 3 different partitions I'll need and how much space to allocate for each on let's say 20GB of space.

I remember I had a choice "Use all free space" and it was soo simple I could have windows and some unallocated space on hard drive and Ubuntu would of use it . Now I don't see this option. I see use entire disk ...or advanced where You have to create on unallocated space all parts of partitions needed that's

EDITED: My System info if u need it.

Mobo: Asus P6T Deluxe
CPU: i7 920
RAM: 6GB G.Skill PC1333 cards
BOOT HDD: OCZ Vertex 2 64gb x 2 in RAID0

[Code]....

View 9 Replies View Related

Ubuntu :: Create A Raid0 Array Of Drives?

Feb 20, 2011

Just got 3 extra drives for my machine.

2x160Gb sata
1x 165Gb sata

How do i create a raid0 array of these drives? On each drive i have got a partition whose size is 160GB and formatted to type fd (Raid Autodetect) i have tried the following:

Code:
mdadm --create /dev/md0 --level=0 --raid-devices=3 /dev/sdb1 /dev/sdc1 /dev/sda1
mkfs.ext4 /dev/md0
mount /dev/md0 /media/raid
but for some reason it doesnt work.

[Code]...

View 5 Replies View Related

Software :: Mdadm - Raid0 Array Appear With Only One Disk

Dec 1, 2010

When I set up Ubuntu 10.10 I had only one hdd around so I installed my system with the idea that I will add the 2nd hdd for raid1 later on. Last weekend I wanted to add the hdd, but discovered, that ubuntu created a raid0 array. So I went on and tried different things: removing the 1st hdd from the raid0 array, create a raid1 with two disks, and so on... I finally could syncronize both disks but after a reboot the raid0 array appeared again with only one disk. Now I know, I should have written the mdadm.conf and fstab files... My last tries resulted in a missing superblock. Here is the story:

[Code].....

View 1 Replies View Related

CentOS 5 Server :: RAID0+1 Or Other Setup For 4 Drives?

Mar 30, 2011

I tore down my old ftp server running FreeNAS because it had some issues. I decided to add a couple more drives and install CentOS on it instead. So now I have 4x 2TB drives that I set up yesterday.OS is installed on a usb flash drive exclusively while I chose to set up the 2TB drives in two stripes and then mirrored, for RAID0+1 instead of RAID1+0.

/dev/md0 = drive 1+2 in RAID0
/dev/md1 = drive 3+4 in RAID0
/dev/md2 = md0+md1 in RAID1

Well, the sync time for these two mirrors of blank drives is almost done, having taken some 15+ hours.I chose this setup to have a single 3.6TB file system mirrored to another 3.6TB for "backup". As this is only going to be a headless ftp server, I don't need massive redundancy/backup. A mirror should suffice if I need to pull some files.So now I'm second guessing myself. I'm wondering if it is even worth it to stripe 2 drives into a single volume with such large sync times. Since data xfer will be over internet, I don't require the massive file writing capacity that would be preferable if it were in my home as a NAS. So, the "performance" increase of RAID0 is not strictly mandatory.

I'm wondering if I should just wipe the drives and set them up in JBOD or LVM instead of RAID0 arrays.In case of boot drive failure, I'd be booting a livecd to xfer files elsewhere or recover the boot drive. So, what difference would I see if I were livebooting to md0, md1, md2 for data viewing as opposed to livebooting to an LVM or JBOD array?As an aside, the drives are WD20EARS, which are 4k sectors which I aligned to start at sector 2048 in fdisk.

View 8 Replies View Related

Debian Installation :: Partition Alignment On SSDs In MD RAID0?

Feb 15, 2015

I have two SSDs on which I have configured md RAID 0, with a 16 KB chunk size. My understanding is that Wheezy (and later) installations are smart enough to align partitions on block boundaries, even in md RAID configurations, but to satisfy my own natural distrust, how do I go about actually confirming that it has done the right thing? I have a single root logical volume within an LVM partition, but neither the logical volume nor the LVM partition occupy all available space, and the LVM partition is offset from the end of the disk.

My concern arises from the fact that, when I look at the sysfs entry for my root partition:

# cat /sys/devices/virtual/block/md126/md126p4/start
804818048

This number is not evenly divisible by 4096.

View 2 Replies View Related

Debian :: Make A Boot RAID0 LVM On A Pair Of SSDs

Aug 20, 2015

I would like to make a boot RAID0 LVM on a pair of SSDs (sdc and sdd). The system is already running off of a HDD. I built the RAID0 through the Asus BIOS on the Intel controller. I see:

# cat /proc/mdstat
Personalities : [raid0]
md124 : active raid0 sdc[1] sdd[0]
59346944 blocks super external:/md126/0 32k chunks
md125 : active raid0 sda[1] sdb[0]
222715904 blocks super external:/md127/0 32k chunks

[code]....

My challenge is that when I open Gparted, it only show one disk at a time. I would like to learn how to use Gparted to partition this RAID0 with a UEFI sector and LVM for the rest.

View 2 Replies View Related

Ubuntu Installation :: Grub Not Detecting Win7 On RAID0?

Mar 26, 2010

Looks like Grub2 on my new installation of Ubuntu 9.10 is not picking up a Windows 7 installation on a RAID0 array (using the built-in RAID software from my Asus P5Q-Deluxe)

Here are the results of the boot info script:

Code:
Boot Info Script 0.55 dated February 15th, 2010
============================= Boot Info Summary: ==============================
=> Grub 2 is installed in the MBR of /dev/sda and looks for
(UUID=43b4cb20-dfea-4513-80e9-54d066107c71)/boot/grub.
=> No boot loader is installed in the MBR of /dev/sdb

[Code].....

View 9 Replies View Related

Ubuntu Installation :: Getting 10.04 To RAID Drive With Root On RAID0?

Mar 21, 2011

I ran into this and found a non-trivial solution so I thought I'd share in case anyone else ran into it.I have two 200GB drives so I thought I'd install my system with RAIDed partitions for /boot, / and /home. I would use RAID1 for /boot and /home because GRUB2 can load the kernel from a RAID1 and I thought the extra reliability for /home would be nice. (I may second guess /home on RAID1 once I get to test performance.) I chose RAID0 for / to provide faster application loading.I prepared the drives using a Live CD because I'm not confident that I can do what needs to be done during installation.First I partitioned the drives as:

Code:

hbarta@olive:~$ sudo fdisk -luc /dev/sda
Disk /dev/sda: 200.0 GB, 200049647616 bytes
255 heads, 63 sectors/track, 24321 cylinders, total 390721968 sectors
Units = sectors of 1 * 512 = 512 bytes

[code]....

At this point I could restart and boot from the system hard drives and proceed with configuring my system. I'm not positive that it is necessary to add the modules to /etc/initramfs-tools/modules but I do know that alone is not sufficient. An earlier attempt was to install grub (install-grub /dev/sda; install-grub /dev/sdb) within the chroot and I found that also was not sufficient. I have not listed it above because I think it was not necessary. But on these two issues, I'm not going to reinstall again from scratch just try...

[URL]

Another possibility is to install using the Alternate CD. I did not try that but it may provide better RAID handling. Last week I installed 10.04.2 LTS Server to a RAID1 and it did not experience this problem. However I do not know if it is RAID in general or RAID0 that led to the issues I encountered.

View 1 Replies View Related

Red Hat / Fedora :: RAID0 Setup - Running Out Of Storage Space

Feb 3, 2011

I have a Fedora NAS (not built by me) there is a 1 Tera of storage 2x 500 set at raid 0. The server runs Fedora 7/8 I believe which, runs flawlessly. Sadly, I am running out of storage space and would like to add more. Can I just put another drive in the box? If so, what do I need to do and what impact does it have on the existing raid 0 setup. Ideally I would like to put two additional in but I am not confident how to configure them. Is this just a case of mapping them in Windows 7.

View 2 Replies View Related

Hardware :: Mdadm Raid0 And Ubuntu Server Boot

Mar 27, 2010

I have ubuntu server 8.04 installed. It uses software raid0 (mdadm, two hard disks: sda and sdb). The server crashed after power failure. When trying to boot I get the following messages:

[Code].....

View 3 Replies View Related

Ubuntu Installation :: Lynx X64 On RAID0 Ich10r (dual Boot)

Jun 9, 2010

I've planed to install Ubuntu Lucid Lynx 10.04 x64 on my rig. dual boot setup windows 7 preinstalled Intel ICH10R RAID0 manual partition setup 200mb ext3 /boot 2gb swap 100gb ext4 / GUI installer can see my RAID and allows me to create this partitions manually. But when install begins i'm getting error :

Quote: The ext3 file system creation in partition #5 of Serial ATA RAID isw_dgaehbbiig_RAID_0 (stripe) failed

[Code]...

fdisk -l from Live cd shows me separated HDDs without RAID0 wrap (sda and sdb) Also in advanced section where i can configure boot loader default is /dev/sda, which is part of RAId_0. I'm checking isw_dgaehbbiig_RAID_0 as location for loader, assuming that this would be MBR. am i doing this step right?

View 4 Replies View Related

Ubuntu :: Udevd-work Random Error On Boot On Raid0

Oct 12, 2010

I have a Raid0 setup (see below for details) connected to the ICH10R raid chip on my Gigabyte EX58-UD4P motherboard. On every second og third boot I get the following error:

Code:
udevd-work[157]: inotify_add_watch(6, /dev/dm-1, 10) failed: no such file or directory
udevd-work[179]: inotify_add_watch(6, /dev/dm-1, 10) failed: no such file or directory
The system halts for a seconds or two and then boots on like nothing has happend.

My setup is as follows:

Two 500gb discs in Raid0 on the ICH10R. The first partition 100 mb is a Windows 7 system partition (gaming etc.) and then a 300gb partition for the actual Windos install. Then Ubuntu 10.10 with /, /home, /swap and then five data partitions. Grub is on the Windows system partition.

Ubuntu 10.10 x64 installed via USB. No problems during install. Besides that I have 2x300gb dics on the Gigabyte built in raid controller. Installed with a Hackintos setup using Mac software raid.My fstab looks like this:

Code:
# /etc/fstab: static file system information.
#
# Use 'blkid -o value -s UUID' to print the universally unique identifier
# for a device; this may be used with UUID= as a more robust way to name
# devices that works even if disks are added and removed. See fstab(5).

[Code]...

View 3 Replies View Related

Ubuntu :: Temporarily Copy Data Before Growing RAID0 Array?

Feb 1, 2011

I currently have two hard drives, with my root partition configured in RAID0. I'd like to add two additional hard drives, and include them in my RAID0 array. I need to recreate the array to do this, so I'd like to copy everything off of the existing array, add the drives, build the new array, and copy everything back. I have an external hard drive with four times the capacity of my current array. What would be the best way to copy this data so that nothing is missed, so I can just copy everything back and boot back up? dd, image the entire root partition, mount it after creating the new array, copy everything back (at the filesystem level) dd, image the entire root partition, write it back out to the new array, I'm not sure how this would work, because the partition will be the wrong size, I don't know much about dd. rsync, just rsync everything on root over to the external something else? I plan on booting to a live CD and mounting my current array there, so I won't be working on a live filesystem.

View 1 Replies View Related

Ubuntu / Apple :: Read Files On Software Raid0 Mac Drives?

Mar 21, 2011

I have a set of Mac software RAID 0 drives that my friend gave me for spring break. I need to access a file on the drive in the Extra folder on one of the drives. It contains some startup settings that need to be changed before I can boot it properly. I loaded up ubuntu and tried to access the drive but only the top level files are readable and when I try to access the Extra folder it says "permission denied." The info on the folder permissions tab is User ID: 501 and Group ID: dialout. Owner permissions = r/w, all other groups/users = none. How can I make Ubuntu read/write to this Extra folder?

View 1 Replies View Related

General :: Mount Hard RAID5 Array With Software RAID0 And GPT?

Aug 8, 2009

I couldn't post in General. It said I had insufficient permissions to post there, so, this post does have to do with Windows slightly. Sorry that it's here, but I DID read the rules (I searched, and couldn't find an answer to my problem either)

Anyways, I have a RAID5 array 2.72TB (4x1TB drives) which I used in my windows installation, initialized as GPT, and I used "span" to make the single 2TB partition, and 720GB partition into one partition. I believe that Windows created a software RAID0. Ok, so now I've made the leap away from windows, and am going 100% into Linux (Debian, to be exact) and I'm trying to figure out how to mount this array. I've only done basic web/ftp/ircd server management on Linux before, and never anything with mounting drives. I'm a complete n00b at this stuff.

View 9 Replies View Related

OpenSUSE Install :: How Installer Of 11.3 Deals With INTEL ICH10R Fake RAID0

Jul 15, 2010

I have two 150GB WD Raptors stripped in an INTEL ICH10R RAID0 array. Windows 7 is installed on it in a 100GB partition, there is a 150GB secondary partition, a 100MB system reserved partition created by Windows 7 and there is about 25GB unallocated space to install a linux distribution.My problem is the fake ICH10R RAID which does work only at the moment for me with Fedora Core 13 : Ubuntu 10.04 breaks it but i do not like FC13 very much. So i Googled and Googled for installation problems on this fakeraid and dmraid is involved there is a bug in it at least in Ubuntu 10.04 and openSUSE 11.2, with 11.3 my RAID is detected -> i have a MD RAID popup.

My question is : How to install properly 11.3 on the space left on my fake RAID array without breaking anything although i have a full backup of my system. I don't understand anything of the partitioning part of openSUSE in general. Do i must activate MD RAID, i tried once and my NTFS partitions were not displayed but RAID was detected with the correct size. I am totally lost with this installer.

View 8 Replies View Related

Ubuntu :: 10.10 Installed With WISE In Windows7 RAID0 - Root Filesystem Not Defined

Oct 25, 2010

i have a M1730 with 2 HD in RAID 0. Windows 7 64bit installed. I tried to install Ubuntu 10.10 with WUBI, all ok the installation in Windows. Restarted the system I have 2 multiboot options with the new Ubuntu... it starts but in graphic mode it tries to finish the installation and stops with an error message like that: "root filesystem not defined...".The problem is the raid0 of my disks or other?

View 5 Replies View Related







Copyrights 2005-15 www.BigResource.com, All rights reserved