Hardware :: Digital Output (S/PDIF) For SoundBlaster Live! Not Working?
Feb 19, 2010
After many fruitless weeks of reading forums, newsgroups etc, I still fial to get digital output working my SoundBlaster Live Platinum. Ordinary PCM output is passed to the digital receiver witout a problem, but as soon as I try AC3 or DTS it's all silence. I have unmuted the IEC958 channel in alsamixer and added gain to them. However all still fails. find below the output of relevant commands:
uname -a
Code:
Linux Mediacenter 2.6.31-14-generic #48-Ubuntu SMP Fri Oct 16 14:04:26 UTC 2009 i686 GNU/Linux
aplay -L
Code:
default:CARD=Live
[Code]...
View 9 Replies
ADVERTISEMENT
May 6, 2010
I am trying to output all of my sound through the s/pdif output on my motherboard. It works fine in Windows 7, I just had to go under the sound properties and switch from the analog to the s/pdif. When I try to do the same in Ubuntu, theres nothing listed. Only "internal audio analog stereo" and "HDMI Audio" (from my graphics card) display under the output choices in Sound Preferences. Under hardware only the HDMI and Internal Analog show up as well. I tried looking at the Gnome-Alsa mixer but nothing in there either.
View 2 Replies
View Related
Jul 13, 2011
Mainboard is a Gigabyte GA-790FXTA-UD5, Audio Chip is shown by alsamixer as HDA-Intel - HDA ATI SB, Realtek ALC889. Analog Audio is working fine. Now i tried to use the digital output. And it did not work. AVR and cable are working fine. Software is Ubuntu 11.04.
View 1 Replies
View Related
Aug 15, 2011
I have a shared headphone/spdif jack on my ASUS B53J and am running Ubuntu 11.04 Natty. I am not able to get the digital spdif output to work. I have tested the spdif out under Windows 7 and it works perfectly.
aplay -L
Quote:
default
Playback/recording through the PulseAudio sound server
pulse
Playback/recording through the PulseAudio sound server
[code].....
View 1 Replies
View Related
Mar 21, 2011
I can't find any S/PDIF audio output options in System --> Preferences --> Sound. How do I enable S/PDIF audio output from my onboard audio?
View 4 Replies
View Related
Mar 29, 2010
I can not get any output from the digital optical S/PDIF jack on my on-board audio device. But I am getting an analog signal from the headphone jack. I don't have an RCA S/PDIF cable, so I haven't tested the RCA S/PDIF jack. Below are my system specs and hardware info.
According to my MOBO (DFI Blood-Iron P45) manual, the Audio device is:
Realtek ALC885 HDA CODEC
8-channel audio output
Optical S/PDIF-out and coaxial RCA S/PDIF interfaces
There are 6 phone jacks (including 1 mic), an RCA S/PDIF, and an Optical S/PDIF jack on the MOBO. The output of alsa-info.sh is here:[URL]... Note that I tried several model options (6stack-dig, 6stack-dig-demo, intel-alc889a, auto) for the snd-hda-intel module, but none worked,
View 2 Replies
View Related
Feb 12, 2011
I install a copy from an iso of Fedora 14 on a old Dell Computer with some upgrades not prepriatary hardware. One of the hardware problems I am having is getting my Creative Soundblaster 5.1 Live card to work with Fedora 14. I have been looking for a driver and as of yet have not found one that works well. Do you have any suggestions regarding this so I can do some site development on this machine.
View 3 Replies
View Related
Jul 24, 2010
My sound card (Soundblaster 24 live! USB) stopped working shortly after upgrading to 10.04. everything was fine until the upgrade as well a immediatly after, so I assume that an update was to blame. If I boot the PC off a live CD, all is well and the sound card works fine.
I've tried running
aplay -l
but it assured me that I do not have a sound card on the system to setup! how I find the broken config file or busted driver?
View 9 Replies
View Related
Dec 5, 2010
I migrated to 10.04 (clean install) from 9.10 recently. I have no problems with internal sound card playback but cannot get the USB Creative Audigy Optical port working. I have defined it as Digital Output in Pulse Audio and when an application plays audio I can see Pulse Audio showing output but no output from the Audigy.
I would appreciate if anyone has come across this problem and if so could give some pointers to fix this issue.
View 2 Replies
View Related
Dec 4, 2010
Just installed this card. Can't figure out what I need to do to get it to work. It's a pci express card.
View 5 Replies
View Related
Sep 29, 2010
Sound comes out of my laptop speakers, but only when hardware is selected as "Analog Stereo". "Digital Stereo" does not function at all. I don't think this is a priority though.
More importantly, my headphones do not have sound unless it is only partway plugged into the headphone jack. However, this does not help as sound is still coming out of my speakers. The instant I plug it all the way in, the sound disappears from both speakers and headphones. I have not tested this with multiple headphones (no access), but these ones work just fine in Windows 7 plugged in all the way.
I have tried an amazing number of things back in '09 when I was running 9.10, but gave up as no one could provide the answer. The threads that are related are:
[URL] (Don't worry about read-only file stuff, that is all resolved) [URL]
I am now on a FRESH install of 10.04 Lucid Lynx, so any changes I made in attempt to fix it is gone.
Looking into alsamixer, I found that there is a headphones column, but no bar. It just says it's on. So headphones don't seem to have their own level of volume that's set too low.
Here are some outputs: lcat /proc/asound/card0/codec#* | grep Codec:
Code:
Codec: Realtek ALC663
Codec: Nvidia MCP78 HDMI
aplay -l:
[Code].....
View 1 Replies
View Related
Mar 10, 2011
Alright so I just upgraded my 11.3 x64 to 11.4 using zypper dup and have now lost the ability to play digital output 5.1. Before doing the upgrade I was running alsa rather than phonon but apparently the upgrade decided to enable phonon, and I no longer show digital surround output. The soundcard I have is a CM8738 and I am using the coaxial output on it hooked into my receiver. In system settings->multimedia->phonon->speaker setup the soundcard shows and I have the ability to select different profiles.
However the digital output settings only show stereo and the sound output device the only one listed is CM8738 Digital Stereo (IEC958). I have selections for analog 5.1 and analog 7.1 but neither put anything out of the digital connection. As I said I was running alsa before and was able to do straight digital pass through which allowed my receiver to do the decoding and use all of my channels. How can I setup phonon to use digital passthrough, or switch back to alsa and get that setup again.
View 9 Replies
View Related
Aug 18, 2010
Ubuntu seems to see my onboard audio card but I can't select it in the Sound options as my output. In Alsamixer I can adjust settings and have turned on SPIDIF. It's listed when I run the lspci command as
Code:
00:1b.0 Audio device: Intel Corporation 82801JI (ICH10 Family) HD Audio Controller
So what is the problem?
[code]...
View 1 Replies
View Related
Feb 10, 2010
I have Gateway P-7807u laptop with Ubuntu 9.10 installed, it has HDMI output and I use it to connect to my TV-set. The problem is - not working sound via HDMI, in sound preferences I've chosen duplex digital output, but no success, but picture works well.
View 14 Replies
View Related
Jun 5, 2010
My sound was working, but I got a new SPDIF cable, so I switched it to digital. It worked fine. But then I restarted and now it's gone.
aplay -l tells me I have no soundcard but lspci -v lists
00:14.2 Audio device: ATI Technologies Inc SBx00 Azalia (Intel HDA)
Subsystem: ASUSTeK Computer Inc. Device 836c
Flags: bus master, slow devsel, latency 64, IRQ 16
Memory at f9ff4000 (64-bit, non-prefetchable) [size=16K]
Capabilities: <access denied>
Kernel driver in use: HDA Intel
Kernel modules: snd-hda-intel
So my soundcard is there.
View 1 Replies
View Related
Jul 19, 2010
I've setup an HTPC with xbmc, and I'd like to output the audio from the system to both my digital and analog outputs on my mother board. How do I do it? Can their be a script that duplicates the output of one to the other? Here's what aplay -l said:
[Code]....
View 1 Replies
View Related
Jul 27, 2010
I've done a search on google and on here regarding my issue and I couldn't see anything.
I have the following audio device;
Code:
00:10.1 Audio device: nVidia Corporation MCP51 High Definition Audio (rev a2)
At the moment I have it playing through Analog Stereo Output. (See attached image)
The sound is mostly flawless and I haven't been having troubles with it.
But, because I play audio through my logitech speakers (2 speakers, 1 subwoofer) I should be able to get digital stereo sound shouldn't I?
From the drop down box of the attached image there are two options for Digital Stereo;
Digital Stereo Duplex IEC958
Digital Stereo IEC958 Output + Analog Stereo Input
None of them work for me. Even if I do a restart, I get no sound from Rhythmbox or Firefox.
I use the pulseaudio sound server and I have the PulseAudio device chooser installed. When I had the Digital Stereo Duplex IEC958 selected I used the Volume Meter playback to see if there was any sound coming through. Both left and right showed activity but nothing came through the speakers.
View 6 Replies
View Related
Apr 12, 2010
After some fudging around, I managed to get my 64-bit karmic install to output sound digitally to my amplifier. So far, so good. The amplifier indicates a sample rate of 44.1KHz, while it is capable of 48KHz (higher sample rate would be better, i assume). Also, more annoying, it indicates no signal when no applications are producing sounds, causing it to miss the first second of output when I unpause my music. Windows 7 outputs everything as 48KHz, apparently also outputting silence as the light doesn't blink when i pause a media player.
The question then being: How do I override the default sample rate of digital audio output (if this is even possible, googling suggested that this might be overridden by applications); How do I make my sound driver output silence when no application is outputting sound.
Additional info:
- Ubuntu Karmic x64 (dist-upgraded from jaunty)
- Exaile media player with Normal playback engine and Automatic audio sink
- Asus P5Q-E motherboard
- Philips DFA888 amplifier
View 3 Replies
View Related
May 27, 2010
I just installed Ubuntu 10.4 64bit and cant figure out how to get my digital audio working. I got sound using the 3.5mm jack.
View 7 Replies
View Related
Oct 10, 2010
For no conceivable reason, pulseaudio will no longer output via the spdif connection on my onboard sound card.Up until now, various applications could output digitally (mostly using via the alsa plugin) fine. DVD playback would passthrough DD/dts bitstreams if the application was set to communicate with alsa directly. The sound profile in Ubuntu's audio applet would have to be set to Analog Stereo Output for this to work, no idea why.
Now, all the works is digital passthrough via alsa (i.e DVDs). So definitely not a hardware issue. Regular audio either via the alsa plugin or using pulse directly does not work so no music/system sounds/flash etc. All sliders are unmuted (see pics linked below) and the volume meters all show movement with sound activity. Changing the Profile setting does nothing, I thought maybe it had been fixed so digital actually meant digital.This has happened before (sometimes triggered by DVD playback and DD passthrough) but usually fiddling with the mute toggles fixed it.Possibly this has been caused by a recent update.
View 1 Replies
View Related
Oct 24, 2010
I'm running ubuntu 10.04 and suddenly when plugging my cameras or usb sticks, they don't automount anymore, but they did before. What changed is last days I tried to build and install nautilus-sendto manually from source, and it required dependencies including GTK+3.0 (unstable), I don't know what happened exactly or if my system is broken, because some of this packages built and installed fine and others failed. If someone wants to help with that to get my installation to its original state it would be awesome.I could mount my usb stick installing usbmount, it worked, but I didn't need this before.What I want now is to mount my cameras: here is the output for:
Code:
lsusb
gvfs-mount -l
[code]....
View 2 Replies
View Related
Nov 9, 2010
I can't seem to find this anywhere. I have burned Debian 5.06 for i386 and trying to login when running the live cd. What is the username and password to get in?
edit....
I found 'user' and 'live' but they don't work.
View 10 Replies
View Related
Apr 28, 2011
Live CD: I dowloaded the ISO, burned it to CD, booted from this CD. It starts to load and I can see the purple background with the loading icons. Everything seems normal. But instead of ending up with the login screen, it ends up with a screen that says 'Please remove all bootup media and hit ENTER' or something like this. So I hit enter and then it shuts off my computer. That's it.
Live Stick: So I tried another option and created a stick with 'usb-creator.exe' that is on the CD. Then I start from that stick, but all I end up is a line of 'Syslinux bla bla copyright 20xx-2011'. That's it. Then it does nothing anymore. The cursor is blinking, but no prompt or whatsoever and keyboard input doesn't do anything.
Now something weird: When I insert Live CD and Live Stick at the same time and then boot my computer, then it boots into Ubuntu. Obviously it loads the first parts from CD and then the rest from stick. Because when I'm then in Ubuntu and try to format the stick, it says it can't do so, because there's system files from that stick in use.
View 5 Replies
View Related
Jun 12, 2010
Digital Persona Fingerprint reader is not working on dell 1535. I am using fedora 13 64 bit edition. I have tried using lsusb |grep -i finger but nothing has come up. I have installed all the fprintd packages but still no luck.
View 2 Replies
View Related
Feb 17, 2011
My motherboard has an optical S/PDIF output that I wish to use. When I browse through my Desktop Kickoff | System Settings | Multimedia, I see this: My digital audio output Furthermore, selecting "Test", results in the test track being heard. I can also see and use this output port in the Amaroc media player (don't know how many other - see later).
However, when I try and see this S/PDIF interface from a "system" view point - YaST | Hardware | Sound, this is all I see: My sound configuration
The issue I'm trying to solve, is that there is no audio output on the S/PDIF for general "system" activities - logon fanfares, Firefox media (Flash), alerts etc.?
View 9 Replies
View Related
Jun 30, 2010
I build a HTPC from an old computer and installed Ubuntu 10.04LTS. I'm new to Linux and have spent a few weeks tracking down and fixing a few problems.t the moment I've exhausted my ideas as to why I have no S/PDIF output, I'm trying to use the onboard audio from my motherboard. I get sound from the analog output to my computer speakers, but when I connect the coaxial S/PDIF output to my amplifier I get no sound. tried removing and reinstalling ALSA, muting and unmuting outputs in ALSA, checked my amplifier settings and inputs, and probably a few other things I've forgotten. I also tried to follow the troubleshooting and howto guides to the best of my abilityHere's a list of what I have:OS: Ubuntu 10.04LTS
Motherboard: P4C800-Deluxe
Onboard Audio: SoundMAX AD1985 AC '97 audio CODEC supports 6-channel 5.1
CPU: P4 2.60GHz overclocked to 3.12GHz
Memory: 3gigs Dual DDR PC3200
GPU: GeForce 7800GS
HDD: 2, 160GB SATA HDD and 1TB SATA HDD
View 1 Replies
View Related
Aug 25, 2010
i'm using optical s/pdif output, called "hda intel, ad198x digital (iec958 (s/pdif) digital audio output)" in phonon preferences. sounds works just fine -- except i can't use multiple audio sources simultaneously: for example amarok+videos is a no-no. only the first audio source plays, so i have to close amarok in order to listen to any flash videos. i had this problem already with opensuse 11.2, but couldn't figure it out (using 11.3 now).
i just recently got a hunch that it might have something to do with mixing and the s/pdif, and i tried using analog output ("hda intel (ad198x analog)"). lo and behold, it works! amarok+flash that isash still doesn't still consider this a major leap forward.however, i'd like to keep using my optical output.
View 1 Replies
View Related
Oct 8, 2010
I have a system with an on-board S/PDIF output (the one I want to use) and a ATI graphics card that has an HDMI output and therefore an own audio device./proc/asound/cards shows me the following:
Code:
0 [SB ]: HDA-Intel - HDA ATI SB
HDA ATI SB at 0xfe7f8000 irq 16
[code]....
View 4 Replies
View Related
Jun 14, 2010
if Soundblaster 5.1 will work on opensuse 11.2,need it for 5.1 sound.
View 4 Replies
View Related
Oct 21, 2009
I am trying to play music on Fedora 11, the sound plays, but its very fast, skips and clips. Soundcard is a soundblaster 5.1
View 2 Replies
View Related
