This is my third SLackware install. I installed 10,12, now 13. the Xorgsetup has changed I think, it does not display the screen to choose Horizontal and Vertical settings for the monitor. In addition, how can I set the Refresh rate?
View 2 Replies
Just a day ago I did a clean install of 10.04, after wiping the disk clean of 9.10. So far everything's working great. Except for my old dual-screen configuration. A year or two ago I badly wanted to have 2 monitors, where both would share the same desktop/workspace allowing me to drag windows back and forth between the two. After a lot of research, I finally was able to put together (although a probably quite sloppy) xorg.conf file that did the trick for me.
My case is somewhat unique in that my left monitor is horizontal, while my right monitor is rotated 90 degrees, and is vertical. In 10.04, my old xorg.conf file sort of works, but I have problems on my right, vertical screen:
- when I move my cursor onto the vertical screen, when I try to move it above where my left, horizontal screen's boundaries end, my cursor jumps down to the bottom of my vertical screen. I can't access anything with my cursor above this boundary on my vertical screen. Note that my vertical screen's bottom is in aligned with my horizontal screen's bottom, and that the vertical screen sticks up above the horizontal screen, as both have a 1680 x 1050 resolution/widescreen aspect ratio.
- however, it appears that only my cursor is having issues accessing the upper part of my vertical screen. When I maximize windows in this screen, they properly fill it up entirely like they should. (but I still can't access the top parts of these applications with my cursor).
So obviously there must be some boundary managing where my cursor is allowed to go, and another set of rules defining the boundaries that the windows themselves can be shown/take up. Also note that because of my right monitor being rotated vertically, I'm forced to use Xinerama. Can someone help me go through my xorg.conf file, below, to help me get this "simple" cursor issue fixed? I'm sure it's just one minor thing that has to be changed, but I'm not sure what:
Code:
# nvidia-settings: X configuration file generated by nvidia-settings
# nvidia-settings: version 1.0 (buildd@palmer) Sun Feb 1 20:21:04 UTC 2009
# nvidia-xconfig: X configuration file generated by nvidia-xconfig
# nvidia-xconfig: version 1.0 (buildmeister@builder57) Thu Jul 17 18:39:19 PDT 2008
# xorg.conf (X.Org X Window System server configuration file)
[Code]...
I installed Karmic on an older PC I had laying around, and the only trouble I am having is with screen resolution. It uses an old ATI chipset (onboard) for video, and it doesn't seem to do EDID correctly, so I can't display anything higher than 800x600. I have tried creating an xorg.conf, but it's still not working. How can I tell Xorg to ignore the fact it can't detect a widescreen monitor and display something larger than 800x600? I noticed the log says the sync's are out of range, but I am not sure how to fix it.
Here is my current xorg.conf.
Code:
Section "ServerLayout"
Identifier "X.org Configured"
Screen 0 "Screen0" 0 0
InputDevice "Mouse0" "CorePointer"
InputDevice "Keyboard0" "CoreKeyboard"
EndSection
[Code]....
Whenever I change my Display and Monitor settings. The settings keep getting reset every time I restart KDE. The changes work fine and as expected, they just keep getting wiped every time for some reason.Here is what the settings look like after each restart:And here is what I'm trying to modify them t
View 1 Replies View RelatedI have gpointing devices 1-4 installed on ubuntu 10.10. The vertical and horizontal scrol both used to work. I have the latest 1.1.1 dkms synaptics driver posted in that bug forum. But now the horizontal scroll using two fingers does not work at all. I have it checked under mouse settings AND in gpointing devices. Is this a known bug?
Apparently I can't delete this. It has been solved. Smooth scrolling in Chrome kills horizontal scrolling
I don't seem to have an "xorg.conf" file.
Gateway SB400a computer with Edubuntu Lucid installed. The problem first cropped up when I installed the Edubuntu packages on Ubuntu. I did a fresh install with Edubuntu and the problem persists. I don't want to go back to Ubuntu since this computer is for my Grandkids and I want to the Edubuntu stuff for them.
I don't have the specs handy, but I can get them. what I have to do to get them. (it happens when you get old)
EDIT: From my xorg.0.log: (--) PCI:*(0:0:2:0) 8086:2562:107b:4000 Intel Corporation 82845G/GL[Brookdale-G]/GE Chipset Integrated Graphics Device rev 3, Mem @ 0xf0000000/134217728, 0xffa80000/524288
I am using Linux 2.6.29-020629-generic #020629 SMP Tue Mar 24 12:03:21 UTC 2009 i686 GNU/Linux ubuntu.
I have a widescreen lcd laptop and the current resolution is set at 1280x768 pls see output of xrandr here for more information [url]
I want to change the resolution to 1024x768. I can do in ubuntu' display tool. The problem is that once I change it, the output does not take up the whole screen it has blank spots on the left and right side
For a better understanding please have a look at [url] and [url]
In open suse the system sets it at 1024x768 without any blanks on the left and right corner. You can have a look at it here [url].
My current xorg.conf is details is at [url].
Please also find my xorg.0.log at [url]
The lcd does not have any controls to tweak.
Been trying to setup my xorg.conf file to have a 1920x1200 screen.Strange behavior: when my X starts up, I see my mouse cursor, can move it around. It's small enough to suggest the 1920x1200 resolution took, is working.However, the rest of the screen remains black. No login prompt.I've looked at /var/log/xorg.conf, no errors.Is there something else I can look at?
View 1 Replies View RelatedI am Currently attempting to set up a Dual Screen setup at my work but seem to be having some strange results. For some reason the O/S is only recognising one of the monitors, it knows exactly what the Make and model of the monitor is but doesnt appear to know that there is another monitor plugged in. It constantly says that there is 2 screens plugged in but lists the second screen as "CRT-0" even if no DVI cable is plugged into the second screen. This has really troubled me and has really got me thinking. I have set-up other Dual-screen setups with exactly the same hardware previously and it has worked fine? I am using a Lenovo A58 Tower with an Nvidia Quadro FX-380 Graphics card that I know is capable of dual Dual-link DVI output! With 2 x LG W3000-H Monitors running Fedora 12.
View 1 Replies View RelatedI have never used Linux always windows so heres the problem the display only has 2 settings 640x480 and a smaller one and it say unknown monitor. I installed the drivers in hardware driver in systems I'm running Ubuntu v 9.10 if that matters and the video card is a Nvida mx440.
View 1 Replies View RelatedI'm trying to get my secondary display (DVI-Out) working on a laptop (built-in monitor & external display) and I'm afraid I made quite the mess of it installing the proprietary driver only to learn that my old ATI card is no longer supported and having to clean that up and reinstall the original distro driver!Anyways, I reverted back to the open source driver and all is ok. That is until I reboot. If I reboot with the DVI display connected then both displays are brought up in 640x480 res and look terrible.
What do I have to do to be able to leave my DVI display connected when I start up the machine and get it to render the way it does when I plug in the display after the machine is running?I suspect I need to create an xorg.conf file but these fancy modern Linuxes these days don't come with one (or maybe they no longer need it anymore).
I am wondering if there is a basic tool out there that will work with graphics card powered by FOSS drivers that allows to adjust resolution (and configure secondary monitors) and then save that configuration so it can automatically be restored next time the system starts up.
View 1 Replies View RelatedI am wondering if there is a basic tool out there that will work with graphics card powered by FOSS drivers that allows to adjust resolution (and configure secondary monitors) and then save that configuration so it can automatically be restored next time the system starts up
View 3 Replies View RelatedI'd like to solve a little problem that I have connecting my notebook with an external VGA monitor.Everything seems to work fine, but when I close the laptop monitor, also the external monitor shuts down.I've tried to find different energy-saving setting for laptop display and external monitor. with no luck...My video card is an ATI Radeon Xpress 200M. On the ATI website there is no catalist control center for linux. (It would be very useful). So, for now, I can only use the display options on the panel.
View 4 Replies View RelatedI want to be able to change the settings for my top down dual head display. Basically one monitor sits on top of another right now. How it was setup before was that they used to sit right next to each other so when you mouse over to the right it would go to the new screen. The problem is now when one sits on top of the other I want to be able to just mouse up instead of mousing over to the right. I don't want to use the gui to be able to do this. I want to find out what config file and specifically what setting in the config file would allow me to change this.
View 2 Replies View Relatedi have just put a Geforce 7300 GT graphic card into my machine the problem is the max resolution I can get is 1024x768 at 60 hz the screen is a benq fp71g+. also the screen goes blank when i click on the display icon in system settings. i know that the screen can be run at 1280x1024 so I don?t know where the problem is.
View 3 Replies View RelatedI am new to this forum. I am a both rhel5 and fedora user.I can not configure my Samsung syncmaster 632nw monitor to display full screen at 1360X768.There is huge blank space on left and right portion of the monitor.The maximun resolution is 1024*768 and minimum is 640*480.
I have tried many times to solve it using xorg.conf but still unable to do it.
Here is xorg.conf's content :
I've just installed OpenSUSE 11.2 on a new machine. Because I was still using another machine as my main box while building the new one, the monitor attached when it was installed has a resolution of 1280x1024 @ 77Hz. I've now moved it to be my main machine and the monitor is a widescreen 1680x1050 @ 60Hz model. When I boot it normally the screen fails to come up - even GDM doesn't show. If I boot in failsafe mode the system comes up fine, but in 1280x1024 mode. The 'Configure display settings' icon shows the monitor as 'Unknown'. Couple of things I tried:
1) Switched to runlevel 2 and logged in as root. Ran Xorg -configure and looked at the xorg.conf.new that was installed, but it just had generic info for the monitor:
[code]....
2) While still in runlevel 2 and logged in as root I did a startx. This brought up the X display in 1680x1050 ok, and clicking on the 'Configure display settings' icon showed it had correctly identified my monitor and had set the size and frequency correctly.
3) Given the results of (2), I then tried logging in as myself in runlevel 2, did startx again, but this time the display failed to come up again.
I installed the nvidia proprietary drivers with click-install and everything perfect, I have desktop effects working but the problem is that when you open the config. screen settings to make sure everything was really good, I get to screen unknown April.
The maximum resolution is the correct 1440 * 900 for 19 "but the refresh rate by not recognizing the monitor down to 50hz me and gives me the option to 60hz as it was before installing the nvidia drivers.
How can I fix the display settings?
A few months ago my monitor broke and began using an old one that does not have EDID.Since then i havent been able to configure my computer with a stable video configuration.I`ve tried a thousand times to edit xorg.conf and i actually got it let me use resolutions higher then 800x600, but when i reboot my computer my usuall setting 1024x768 gets switched back to a lower one - its a pain... my icons get scrambled, the gnome panels, etc.Do I need to edit any other file then xorg.conf?
And another thing I noticed today is that the gnome display manager does not recognise the higher resolution of nvidia-settings. Does it have a seperate settings file?
Can I copy the setting of the live cd in my current 10.10 build? If Not can I do a new clean install of 10.10 over my current upgraded 10.10 build? My display is screwed & I don't know how to fix it
View 3 Replies View RelatedI just installed Ubuntu 9.10 this evening. I have a Nvidia Geforce 8500GT video card with two monitors hooked up (one to the cards VGA, the other to the DVI). I installed Nvidia drivers and Ubuntu is working with both monitors fine.
The problem I am having is it chose the monitor plugged into VGA as the primary (uses that monitor for the toolbars) when I really want them to go on the monitor that is plugged into DVI. Is there anyway for me to switch which monitor Ubuntu treats as the primary?
I have a Radeon HD 5830, running 3 monitors on 10.10 64bit with the 10.6 video driver. The three monitors ( from left to right ) :
DFP1 : 1152x2048
DFP2 : 1920x1200
CRT1 : 1360x768
The problem I'm having is getting the middle monitor to be the primary one.
Running
xrandr --output DFP2 --primary
puts the panel on the middle screen but my docky and icons stay on the left screen. Flash videos also open up on the portrait left monitor which looks awful. Ideally I would like the icons on DFP1, docky on P2 and flash videos to open on P2. But I would definitely settle for everyone to be on the middle screen and drag it around as I please.
[Code]...
I have an Asus z9100 laptop with an Intel 855GM integrated graphics chip, which is running Karmic (the purpose of the laptop is to be a MythTV frontend so my understanding is that it needs to run 9.x in order to connect to the MythTV 0.22 backend - I have installed and configured this using the installable Mythbuntu package) and the laptop is subject to this bug which causes random freezes:
[URL]
So, following advice for similar freezes I've seen, I have added the following options to my grub menu.lst on the kernel line:
nolapic nomodeset
and I have edited xorg.conf so that it makes use of the vesa driver instead of the Intel driver. This results in no freezes and if I wanted to watch Myth on the laptop screen I'd be squared away. However, the laptop has a damaged screen so the point was always to output the signal to an external monitor via its VGA out.
When I attach the external monitor and boot with the setup as described, the external monitor is never detected. But I noticed that if I remove the "nolapic nomodeset" from the kernel boot line, it is detected. However, signal is only output to it during the earliest part of boot (when the Ubuntu logo is in the center of the screen before the full-screen graphic with the animated progress line), after which the external monitor goes black and all the display output goes to the laptop screen. The external monitor power button is still lit up green as if it has been detected and is receiving signal, but it's just a black screen.
get the signal out to the external monitor after the initial part of the boot process, using the vesa driver? Here is the current state of my xorg.conf:
Code:
Section "Device"
Identifier "Configured Video Device"
Driver "vesa"
EndSection
[Code].....
I have a netbook (Acer Aspire One) I'm running Slackware 13. and usually, I prefer to connect an external monitor. When I switch my machine on with the monitor connected, the display is duplicated on both screens and since I just want the netbook's screen to be off and only see the display on the external monitor, I can doxrandr --output LVDS --off
Great! However, it's a hassle to do this every time I log in and I'd like to automate the process if possible. I did some googling and I found that if you want to automate xrandr commands, you can put a script in /etc/X11/Xsession.d/ (see this). I wrote the following script to automate my xrandr commands and since the Xsession.d directory didn't exist, I tried creating it. The script was called 45custom-xrandr_settings, as the one on the RandR wiki is called the same.
Code:
#!/bin/bash
# Check whether the external monitor is connected
[code]...
I have Ubuntu (running Jolicloud) on my HP dv2000 laptop, connected to my Sony AV Receiver through HDMI to use the TV as an external monitor. However, the resolution seems to be slightly off as the outer edges of the screen are cut off. Is there a way to fix this by editing the xorg.conf file? My current setup is below. I tried adding the line "Virtual 1244 700" to the subsection "display", but when I restarted it threw me into low graphics mode. Is there anything else I can try?
I also tried setting up the resolution at 1920x1080 on the TV and kept the default resolution on the monitor as 1280x800, and as you would expect displays the entire desktop in a smaller version on part of the tv. However, the desktop is still offset, leaving the top and left margins cut off. So, perhaps I need a way to offset the screen? Is this possible in xorg.conf?
I have installed Ubuntu 10.4 on Virtual Box, I have installed it successfully, the only problem is when I check the display settings it only have 2 options : 600 X 400 and 800 X 600 and this makes it difficult to work on Ubuntu as 800 X 600 is half the size of my desktop. How I can increase / configure the display settings so that atleast I can fit ubuntu screen into my screen size.
I did install the addition application, restarted the OS but still I don't see any display resolution 1200 X 800, tried pressing ctrl+D nothing happens, after installing I saw it updated mouse cursor now i don't have to press ctrl key again n again to enter into the ubuntu OS but still struggling with the resolution as it's too small, please guide me (here is the screen shot of my screen after installing the addition app).
When I start my system its getting booted through LAN and it showing login screen after I login it shows only black screen. Whether is may by Video adapter problem?
This problem came after I run a Perl portscan program, this script just scan all the ports from 0 to 65535 and reports which port is open and closed.
I (very!) recently installed Mandriva (10.1) on my old-ish HP tx1000 laptop, and cannot connect it to my TV (via the usual external VGA connector) without considerable picture distortion: the image scrolls and wobbles, as if the vertical adjustment is faulty. (One used to get this effect with one's TV if the antenna wasn't properly adjusted.)
I can see both monitors in "Monitor Preferences" - and have tried playing with the parameters available there (there is a general refresh rate setting, but nothing to adjust vertical rate alone), without having any effect on the scrolling distorted image. I can drag windows back and forth between the two monitors, though only the laptop one is usable.
I have an Nvidia card and I am using ubuntu 10.04. Before installing the ubuntu nvidia restricted drivers, the boot screen with the ubuntu logo would cover the entire display area of the monitor. But now, after installing the Nvidia driver and fixing the display resolution of the boot screen with the Plymouth fix, the boot screen doesn't expand to fit the entirety of the monitor display area. How can I fix this? There is a good 2 inch off from either side of the display while booting.
View 3 Replies View Related
