Fedora Networking :: Wlan Via Belkin Usb Not Working?
May 2, 2011
Installed F14 on my daughters HP Pavilion a131On. I rebooted multiple times. Do I need to activate something? I'm new to all of this but read through many threads to do as much as I could myself. I used the GUI to load the rt3070 drivers rather than rpm. The GUI is easier I think and should be equivalent. Please let me know what else I need to do. Fedora has been great on my Lenovo but this usb wlan stuff has been a pain.
I'm running Fedora 15 KDE on a Sony Vaio VPCS13V9E. No problems in connecting to the wlan. Today I upgraded the system. There was an upgrade for Network Manager. After the upgrade the system is not able to connect to the modem - router (Linksys WAG320N) any more. Network manager keeps on crashing and sends messages like "network disabled" or "connection failed". Kde demon is reporting errors too. I guess the new version of Network Manager is bugged, because before the upgrade it did work well ... (unbelievable!).
I have a Dell XPS M1330. I installed Fedora 10 on a separate partition and left Vista on the first. It was working just fine and for some reason all of the sudden it is not recognizing the Wireless controller. Vista is still working fine although I did get a couple of "WLAN controller has stopped working" errors. I suspect I may have a physical problem with the controller but I'm confused as to why Vista is still using it but Linux is not. The actual physicall "WIFI" light on the laptop does not even illuminate when I boot Linux. No wireless networks appear in the network list under Linux. Particularly since it WAS working fine for months...
I have an HP Pavilion notebook with a Broadcom WLANcard that had been working very nicely in Fedora Core 10 until this evening, when I took my notebook to a conference room where there was no internet access. (I tried to connect to wireless networks, but there were none in the area, as I discovered.) am now unable to connect to my local (home) wireless network as the device is now non-existent . Can someone please walk me through the steps to fix this or re-install it (I have tried reinstalling broadcom-wl, but that didn't help). My lspci listing is reproduced below:
Code: 00:00.0 Host bridge: Intel Corporation Mobile 945GM/PM/GMS, 943/940GML and 945GT Express Memory Controller Hub (rev 03)
I've got an old IBM Thinkpad T41 that I just play around with Ubuntu on. The internal Wireless card is broken, so I bought a Belkin F5D8013 PCMCIA Wireless N card a while ago. It worked fine with Ubuntu 8.04-9.10, but it will not work with 10.04. It sees the networks just fine and will let me type in the network password, but it will not connect. Everything else in my house connects without a hitch, so I know it is Ubuntu causing the problem.
I have a Compaq AMD64 that has ubuntu 9.04 on one HD that works great. I've installed 10.04 on a separate HD and had problems installing it. I have 10.04 running now but I can't get my wireless card to work. During installation I skipped setting up the wireless network. Now when I boot into the 10.04 partition I cannot get the nm-applet to work. I can't get it onto the task bar and I don't see it anywhere else.
I checked to see what drivers are installed, and since I have no connection with that OS I can't update or DL drivers for it. I'm pretty sure that it is because I skipped setting it up during installation. What do I need to do to get the wireless working now? I checked other threads and none seem to pertain to my situation. Since I have to log into the 9.04 partition, I can't copy/paste outputs very easily.
i am complitly new in Ubuntu and the world of Linux in general, so i said to my self its better late then never, i installed the last one 10.10. but i am having trouble with my wifi usb adapter (BelkinF5D7050 v 1000), the same adapter works perfect under XP in the same PC. when i go to NM i dont see it in the list of network cards "i see just my two other normal network cards + loopback" and i have permanent small "x" on the icon of NM up in the task bar, even if check or uncheck "Enable Networking", it alwayes show a info bubble "you are now offline", here is the result of all the command line that can help getting better view on my problem
I have just installed Ubuntu 9.10 alongside Windows 7 and it is not picking up my Belkin N wireless adapter?? So I went to go and download the Windows Wireless Drivers (ndiswrapper) software so I can install my adapter and the download center just says "Not available in the current data" and wont let me download it? Also I tried to download my nVidia drivers from software center and it said the same thing?
Never before have I had a problem with Ubuntu until now So can anyone point me in any directions as to how to get these installed???
I'm trying to get internet set up on my grandad's laptop (sony pcg-f590), which has a fairly old pcmcia belkin 54g wireless card. I've installed the relevant bcmwl5a.inf driver through ndiswrapper, and for a time wireless worked so I installed updates through update manager. however after restarting the network manager menu comes up with "wireless networks disconnected" and no list of networks (I know there are because my laptop works and his is sitting next to the router!). The light is on on the network card so I know the laptop is talking to it. Unplugging and replugging the card does nothing, and neither does restarting again.
I tried getting a Belkin USB Wireless adapter:N150 to work in a fresh installation of 10.4 with no success. After reading several forum posts I tried both solutions with ndiswrapper and the XP driver and with the Ralink native driver with no luck.
Code: lsusb Bus 005 Device 008: ID 050d:935a Belkin Components Bus 005 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
very new to using fedora and trying to install my belkin wireless adaptor is not working at all. It reads the disk but says there is an error.it still works fine on windows so i'm not sure how to fix this.
I have a Thinkpad T400 notebook that dual boots windows 7 and Ubuntu 9.04. My wireless has worked both in windows and ubuntu for the past several months. However 2 days ago, the wireless in ubuntu stopped working. I think this may be a result of trying to set up a static eth0 connection between my laptop and an embedded board, but I dont see how messing with eth0 would stop the wlan from working.
Symptoms: When I left click on the network connections icon in the tray, all it lists under "Wireless networks" is "device not ready". Needless to say, there are no networks available to connect to. Also the wireless is working fine under windows.
I'm a new user of Ubuntu and I think I need some help but let me mention before that I got this up working on a Debian system.My current kernel version is $ uname -r 2.6.32-27-generic.The problem is that my wlan card is not working any more such that my system freezes every time I enable networking with the hardware switch on my laptop.Therefore I bought a USB - WLAN stick and try to get this working.
Network Manager has the option "enable wireless" greyed out if I disable the hardware switch.If I enable the hardware switch and remove the module of my wlan CARD before (modprobe -r iwl3945) it says "wireless disconnected" for all networks.
I have just installed Ubuntu 9.10 on an Acer TravelMate 290E. I've got internet connection through the Ehternet Cable, but when I plug in the D-Link WLAN USB device, although the system recognises it, it is disconnected. How can I connect the WLAN USB device adn get it to work?
I have a desktop and laptop both running ubuntu 10.04. I have them going through a wireless router, the desktop is wired of coarse. I installed just about all the samba packages in synaptic that have the little ubuntu symbol next to them on both desktop and laptop except the Kde and document packages. I installed the two necessary packages to enable personal file sharing to work. But I can't seem to access files back and forth from these computers.
Am all of 2 days old on Opensuse 11.0 having just installed it on my old PC. All my experience has been with XP/Vista and Macs and it took some courage to finally try this out. My Belkin F5D9050 wireless(g+ MIMO) usb network card is recognised in yast but does not connect to the internet. On reading through forums I understand that this adaptor uses RAlinks RT73 chipset and support for should already be available in the OS. Is this correct ? If not, where do I get the driver for this and how do I install this. As per the Belkin site, Opensuse driver support isnt listed. Am struggling due to the unfamiliar environment and am not aware of terminal commands.
I'm using Ubuntu 9.10 on a Lenovo ThinkPad T61 using an Intel PRO/Wireless 3945ABG. My laptop's ability to connect to a wireless network stopped last night, and I'm not sure why. It's definitely something on my end, as my roommate can connect to the internet on a Windows box. I can wire in without a problem, but that's a pain and my Ethernet cable got lost in the shuffle when I moved back to school. I've been able to get into this network before and nothing about it has changed. I've been able to hibernate and restart and such and nothing has ever needed to be reset.
The router's a D-Link WBR-2310. Wicd and Network Manager see the network (I'm back to using wicd) , but wicd appears to get stuck at "Obtaining IP address..." and says "Unable to connect: Cannot obtain IP address". I know my password is correct (I set up the router and I'm the CS undergrad in the apartment so I manage it), lspci sees the wireless card, ifconfig and iwconfig return information about the interface, dmesg|grep wlan0 doesn't seem to have anything terribly out of the ordinary, but here's that output:
Code: allyanncah@taliesin:~% dmesg | grep wlan0 [ 23.514202] ADDRCONF(NETDEV_UP): wlan0: link is not ready [ 36.609016] ADDRCONF(NETDEV_UP): wlan0: link is not ready [ 38.756143] wlan0: direct probe to AP 00:24:01:cb:4e:7e (try 1) [ 38.758791] wlan0: direct probe responded [ 38.758796] wlan0: authenticate with AP 00:24:01:cb:4e:7e (try 1) [ 38.760587] wlan0: authenticated [ 38.760609] wlan0: associate with AP 00:24:01:cb:4e:7e (try 1) [ 38.763318] wlan0: RX AssocResp from 00:24:01:cb:4e:7e (capab=0x431 status=0 aid=1) [ 38.763322] wlan0: associated [ 38.765502] ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready .....
I've tried: - reinstalling wicd - uninstalling wicd and installing network-manager - restarting - shutting down and booting back up - restarting the router - sudo /etc/init.d/networking restart - taking the interface down and back up with ifconfig
I haven't changed anything recently in regards to my wireless card, and all the fixes I've tried are things I've done before without an issue. The only thing I'm wondering about is if doing a hard reset might have broken something (I know this is a cardinal sin, but there's a whole 'nother problem I haven't been able to fix with the OS hanging every once in a while over a VPN daemon when it tries to shut down or restart -- I've left it for hours to see if it actually gets anywhere and no luck, won't do a soft reset). I'm nervous about reinstalling the driver just because I've never had to do it and drivers are a finicky business. I imagine there's a config error somewhere?
My problem with UBUNTU is that I can not use acer-wmi because I get this ERROR :
Code:
... so I can not use the acer_wmi . But this is not my only Problem :
It is most likely caused of the missing " Firmware " / Driver for my WLAN Card ( Internal ) . Currently I use Ubuntu 10.10 but I tested 10.04 too before 10.10 and it found my Card but not the Button .
So I want to know if there is any solution for my problem .
If it is important :
I use an Acer eMachines e525 with Windows Vista Home Basic ( Pimped up ) and Wubi . I saw a lot of people with simmilar problems they have it as only boot option .
I updated Ubuntu to 10.04 after which I noticed the wireless indicator lights on my HP laptop were continually flashing between blue and orange and network performance seemed slow. I did some searching and found and implemented the following change to stop the flashing:
gksudo gedit /etc/modprobe.d/wlan.conf
Copy and paste the below line:
options iwlcore led_mode=1
Since making this change the wireless connection is shut off and I can;t get it to work at all. I first tried simply to remove the change to get back wher I was, but I can;t do that. Can sopmebopdy toell me at least how to get rid of this wlan,conf file ( it was created by the above command) so I can start over?
Coincidentally since making this change my Windows Vista OS fails to start because of errors attributed to a software or hardware change, of which there were none other than the Ubuntu wlan.conf change. . It may be unrelated but I am suspicious of the coincidence. I am running Vista and Ubuntu in a dual boot configuration and all ha run very well until I did the Ubuntu wlan.conf change.
I am now attempting a complete recovery of my Vista system, since it seems irreparably broken. Again coincidence or not?
(For the record, I have already read the other threads. Either they don't work for me or are too difficult.) My laptop is an Acer TravelMate 250. I have installed Ubuntu 10.10 (2.6.35-28 generic i686) after erasing Windows 7. At first, the usb wireless adapter worked. Then, I restarted the PC because of some updates and it didn't work anymore. In "edit connections" I find "Auto SpeedTouch8350DB" which is the wireless connection (on my sis's computer it works). When it tries to connect, I'm asked the password but it doesn't work.
My PC has a broadcom wlan adapter. When I clean installed Fedora 15 about two weeks back, the wifi wasn't working on its own. I searched the internet and found out that installing broadcom-wl and akmod-wl would solve the problem. I tried it, and the wifi started working after that.
Wifi not working means there is no wireless option in the network settings and the wifi indicator light is off.. when wifi started working both of these got fixed
Now i did a yum update yesterday, after which my wifi has stopped working again. No use of reinstalling broadcom-wl, akmod-wl, or even kmod-wl...
I have a Dell Inspiron 1525 laptop using Dell Wireless 1395 WLAN Mini-card (This is what Windows Vista says I have). I have installed Ubuntu as dual boot with existing Windows Vista. Wireless is not working in Ubuntu but working flawlessly in Windows.
Here is the output using CODE: lspci. hai@ubuntu:~$ lspci 00:00.0 Host bridge: Intel Corporation Mobile PM965/GM965/GL960 Memory Controller Hub (rev 0c) 00:02.0 VGA compatible controller: Intel Corporation Mobile GM965/GL960 Integrated Graphics Controller (rev 0c) 00:02.1 Display controller: Intel Corporation Mobile GM965/GL960 Integrated Graphics Controller (rev 0c) 00:1a.0 USB Controller: Intel Corporation 82801H (ICH8 Family) USB UHCI Controller #4 (rev 02) 00:1a.1 USB Controller: Intel Corporation 82801H (ICH8 Family) USB UHCI Controller #5 (rev 02) 00:1a.7 USB Controller: Intel Corporation 82801H (ICH8 Family) USB2 EHCI Controller #2 (rev 02) 00:1b.0 Audio device: Intel Corporation 82801H (ICH8 Family) HD Audio Controller (rev 02) 00:1c.0 PCI bridge: Intel Corporation 82801H (ICH8 Family) PCI Express Port 1 (rev 02) 00:1c.1 PCI bridge: Intel Corporation 82801H (ICH8 Family) PCI Express Port 2 (rev 02) 00:1c.4 PCI bridge: Intel Corporation 82801H (ICH8 Family) PCI Express Port 5 (rev 02) 00:1d.0 USB Controller: Intel Corporation 82801H (ICH8 Family) USB UHCI Controller #1 (rev 02) 00:1d.1 USB Controller: Intel Corporation 82801H (ICH8 Family) USB UHCI Controller #2 (rev 02) 00:1d.2 USB Controller: Intel Corporation 82801H (ICH8 Family) USB UHCI Controller #3 (rev 02) 00:1d.7 USB Controller: Intel Corporation 82801H (ICH8 Family) USB2 EHCI Controller #1 (rev 02) 00:1e.0 PCI bridge: Intel Corporation 82801 Mobile PCI Bridge (rev f2) 00:1f.0 ISA bridge: Intel Corporation 82801HEM (ICH8M) LPC Interface Controller (rev 02) 00:1f.1 IDE interface: Intel Corporation 82801HBM/HEM (ICH8M/ICH8M-E) IDE Controller (rev 02) 00:1f.2 SATA controller: Intel Corporation 82801HBM/HEM (ICH8M/ICH8M-E) SATA AHCI Controller (rev 02) 00:1f.3 SMBus: Intel Corporation 82801H (ICH8 Family) SMBus Controller (rev 02) 02:09.0 FireWire (IEEE 1394): Ricoh Co Ltd R5C832 IEEE 1394 Controller (rev 05) 02:09.1 SD Host controller: Ricoh Co Ltd R5C822 SD/SDIO/MMC/MS/MSPro Host Adapter (rev 22) 02:09.2 System peripheral: Ricoh Co Ltd R5C592 Memory Stick Bus Host Adapter (rev 12) 02:09.3 System peripheral: Ricoh Co Ltd xD-Picture Card Controller (rev 12) 09:00.0 Ethernet controller: Marvell Technology Group Ltd. 88E8040 PCI-E Fast Ethernet Controller (rev 12) 0b:00.0 Network controller: Broadcom Corporation BCM4312 802.11b/g (rev 01) hai@ubuntu:~$
I patched my wireless driver in order to support packet injection. Using this tutorial:
- Install the Firmware:
Code:
- Create new directory:
Code:
- Now disconnect Internet and unload all your driver (use rmmod command)
- Move/copy the Compat-Wireless patched in /usr/src/drivers directory and unpack the drivers:
Code:
Blacklist the wl driver: (STA driver)
Code:
Currently I'm running Ubuntu 10.10, Kernel 2.5.35-29-generic. I have a Broadcom 4318 for my WLAN and a Broadcom 4401-B0 for my ethernet. I followed the tutorial and I managed to get packet injection working on my WLAN; however, my ethernet connection isn't working. I tried sudo modeprobe b44, but I get the following message:
1) Has anyone had any luck using the above wireless adapter with any of the Fedora releases and ndiswrapper? On the ndiswrapper wiki it says it is supported but I would like to know if anyone has had any personal experience under Fedora.
2) If I install F11 from the live CD, will everything that I need to install and run ndiswrapper be included in the installation, or would I have to download and install via the full DVD? The reason I ask is because the only way this computer has internet is by using said wireless card, so I would not be able to update F11 until after setting it up.
3) If the live CD does not have everything that I need, would it be possible to download whatever it is I need prior to the F11 installation, save it to my external hard drive, and then install it after I install Fedora?
I installed Fedara 15 yesterday. I was running Fedora 13 before. Since I did the fresh install, my wireless network runs really really slow, i.e. a few KBs every 30 seconds whereas it ran at full speed in F13. I couldn't find the reason for it. I now tried the live-CD for Fedora 14 and it runs at full speed out of the box (whereas F15 is slow even with all updates installed). Does somebody know a solution?
Laptop: Lenovo X201 Network Card: Ultimate-N 6300
I gathered uname, iwconfig, lspci and dmesg output for both, Fedara 15 and Fedora 14. But as the number of links is limited here in the forum they're all linked here: [URL]
I am newbie to linux, I am dealing with Fedora core 13. I have already succeedded in building an ad hoc network and a WLAN network. My next step is to get some networking statistics such delay, throughput, etc. So, I need traffic to flow through the network for both multimedia traffic and bulk data traffic. How to send files between nodes on the network (I found commands ftp, rcp but do not know whether they are the correct choice for this). ID their any application to perform this?
Also, I want to perform some video streaming between two nodes to study the behavior of real time data transfer. Is thier any application to perform this?
