General :: 4.0 - 5.0 - 5.2 - While Installing It Shows A Msg AHCI Adapter Drivers Not Available And System Halts
Jan 16, 2011
I had a problem while installing linux 4.0, 5.0 & 5.2
My system configuration is as follows:
MSI 785 GM E65 MotherBoard
AMD Phenom IIx2 550 processor
RAM 2GB Kingston DDR3 1033GHz
HDD 1TB
While Installing linux 4.0 it shows a msg AHCI adapter drivers not available and system halts
While installing linux 5.0 it shows a msg
KERNEL PANNIC and system halts
While intalling linux 5.2 it halts
View 7 Replies
ADVERTISEMENT
Oct 21, 2010
I have a old mac G4 and I just recently installed ubuntu 10.10 on it. It doesn't recognize my wireless adapter at all so I get no wireless on the computer. I've never used any linux distribution in my life so I don't have any idea how to install drivers for it.
View 1 Replies
View Related
Sep 1, 2011
im trying to install the RTL8192CU_linux_v3.0.2164.20110715 drivers so my new wireless adapter works, but I have hit a wall when trying to insert the drivers after makeing them its telling me
"-VGN-NS325J:~/wifi/driver/8188$ insmod 8192cu.ko
insmod: error inserting '8192cu.ko': -1 Operation not permitted
View 5 Replies
View Related
Jul 22, 2009
Just installed Ubuntu 9.04 last night. All seems perfect except on shutddown. It seems to go through all shutdown processes but right about the time you expect the computer to turn off a message says: "system halted [4027.514883]" Have Googled it but no matches. If I just push the on/off button at that point it shuts off immediately
View 4 Replies
View Related
May 18, 2011
I recently decided to install Ubuntu 11.04 on a 320gb hitachi sata hard drive. This is going into a new system with an Asus MB, AMD Proc, not sure if this matters. Anyway I can not set the bios to use ahci and see the sata drive. I can only use IDE mode with sata enabled. Asus support says to install ahci for os. If I boot into the USB install key and attempt to the install OS I receive a read/write error. I have another drive on IDE that has 11.04 on it and if I try to format the new drive and partition it with Disk Utility it fails with "Error formatting drive: error creating partition table: helper exited with exit code 1: error calling fsync(2) on /dev/sdb: Input/output error". I have tried to use dd and fdisk but I don't believe I need these until I do something else first just not sure how or where to look.
View 6 Replies
View Related
Apr 22, 2011
I am trying to start Damn Small Linux from a USB stick on a HP t5000 thin client. When starting in Default mode the system just stops. When starting i failsafe mode, the text rolls on the console until the message "RAMDISK: Compressed image found on block 0" and then hangs..What does that mean? What could be wrong? Can I run the image without using a ramdisk?
View 1 Replies
View Related
Jan 12, 2011
I have recently installed Linux Mint 10 on my laptop. When I look at the Device Manager in Windows 7, it says I have an Atheros AR9285 Wireless Network Adapter. Right now, I am unable to connect to wifi with Linux. What drivers am I able to install, and how would I install them?
View 3 Replies
View Related
Mar 24, 2011
In order for TRIM to work on an SSD with encryption, I need to make sure to "select the AHCI option before installing the operating system."Does anybody know how to do this? I have no idea what this is talking about. I'll be installing 11.04 with no dual-boot. Just Ubuntu alone.
View 9 Replies
View Related
Mar 17, 2011
intend to install Linux Mint on it. It comes with a BT Voyager 1065 network adapter. If I install Linux, are there software drivers for the adapter available?
View 1 Replies
View Related
Sep 9, 2010
Yesterday I was working on my laptop using the windows 7 partition. At some point it froze and I ended up just having to shutting it down by holding in the power button. When I started it up, it said something along the lines of "can't find bootable partition".
So I made myself a ubuntu flash-drive, and ran
Code:
sudo fdisk -l
This is my output.
Code:
Disk /dev/sda: 500.1 GB, 500107862016 bytes
255 heads, 63 sectors/track, 60801 cylinders
Units = cylinders of 16065 * 512 = 8225280 bytes
Sector size (logical/physical): 512 bytes / 512 bytes
I/O size (minimum/optimal): 512 bytes / 512 bytes
Disk identifier: 0x74836e35 .....
View 1 Replies
View Related
Nov 12, 2010
I have installed ubuntu 10.10 for a short time, now I meet a problem:I always leave for lunch and leave my computer without turning off. When I get back, it shows a window. after I input my password, I enter my system.Then It halts, the only thing what I can do is moving mouse. After halting for nearly one minute, it resumes to normal.I hope someone can tell me what happens.
View 2 Replies
View Related
Sep 28, 2009
Yesterday I was on my Windows computer doing homework. Once Football came on, I hit the Standby button on my keyboard and walked out of my room. Came back at halftime to discover that my system never went into Standby. I turned on my monitor and saw a bunch of code repeating. I don't remember it all, but it was something to this effect
Super Block not compatible with current BIOS
scanning for *insert system file here*.... not found
scanning for floppy drive... not found
scanning for cdrom1... not found
So I hit the restart button on my tower. When it restarted, I was brought back to the same screen. So I unplugged the power cord from my computer and counted to 10. I plugged it back in and this time I got my mobo logo screen and the system appeared to start up fine, until I got to the SATA drive scanning screen. When my computer would scan for my SATA hard drive, it would idle for several minutes, during which a series of periods (".") would show up until eventually I get a message that says: WARNING! - Something wrong with your hardware!
I have troubleshooted a number of things so far:
1) I took my SATA Hard Drive out of my computer and plugged it into my Linux computer and the system booted fine! I used the same SATA cord, so I know both the drive and the cord ARE WORKING!
2) I tested the power cord from the power supply that runs to my HD and it is working just fine.
3) I plugged the HD back into my Windows computer (the original one it was in when I started having this problem) and I ran GParted. When the GUI came on, I could not see any drives and there was a message at the bottom of the window saying that no devices could be found. This was no surprise to me because I watched the verbose mode as GParted booted and it gave error messages when it tried scanning for my hard drive.
4) I have also tried plugging it into the other SATA ports on my motherboard.
5) I tried flashing the mobo BIOS. The flash worked just fine (or at least it appeared so), but the HD is still not being found on the system boot scan.
Bottom line, I know the hard drive is fine because it worked in my Linux computer. So I am thinking it has to be the motherboard. But before I go out and buy a new Mobo and CPU (and possibly new RAM), I wanted to quickly jump on here.
View 1 Replies
View Related
Sep 1, 2011
I need to install wheezy nvidia-graphics-drivers because my video card (geforce GT 425m) isnt supported on the squeezy version. I downloaded the wheezy source code and built it on my squeezy system, some .deb files where created, the problem is I dont know which of those to install, these are the files:
libcuda1280.13-1amd64.deb
nvidia-glx-ia32280.13-1amd64.deb
libcuda1-ia32280.13-1amd64.deb
[code]....
View 7 Replies
View Related
Jan 29, 2010
I am trying to install wireless WiFi USB adapter LM-001 on to my machine. I downloaded the driver ZD1211LnxDrv_2_16_0_0 and followed the instruction rigorously. However, upon issuing the 'make' command, it stalled saying that that it cannot detect the /lib/modules/2.6.9-89.0.19.ELsmp/build directory. Here is the output:
[root@localhost ZD1211LnxDrv_2_16_0_0]# make
make both
make[1]: Entering directory `/root/LM001/LM001-2007/Linux/ZD1211LnxDrv_2_16_0_0'
make clean
make[2]: Entering directory `/root/LM001/LM001-2007/Linux/ZD1211LnxDrv_2_16_0_0'
rm -rf .tmp_versions .*.cmd *.ko *.mod.c *.mod.o *.o src/*.o src/.*.o.cmd menudbg apdbg winevl_iface
make[2]: Leaving directory `/root/LM001/LM001-2007/Linux/ZD1211LnxDrv_2_16_0_0'
make ZD1211REV_B=0
[Code].....
View 1 Replies
View Related
Feb 13, 2010
I have windows 7 and ubuntu karmic dual boot system.i can easily transfer files via bluetooth in windows 7 but in ubuntu it shows a message bluetooth adapter not connected while as i dont use any such adapter while working in windows .
View 4 Replies
View Related
Jan 20, 2011
The situation: computer based on Asus P6T motherboard. Two RAIDS:
- 'boot', on motherboard built-in RAID controller (CentOS 5.5 installed on this RAID)
- 'data' on 3dware RAID card
At one moment a CPU fan fails and the system halts. After the fan is replaced, BIOS informs it's reset and all the inner controller data are forgotten. After I switch it to 'RAID' mode, it remembers it was a mirror raid (RAID 1) installed, but the file system on it is completely trashed.
The 'data' RAID run by external controller isn't affected by the system failure. Three questions:
- is it worth trying to install OS on the rebuilt 'boot' RAID once again? Looks like if BIOS settings are lost for some reason, there's chance of completely losing RAID data
- has someone encountered similar problem with built-in RAID nd was it possible to recover data?
- will the software RAID be worth creating instead of using hardware RAID to replace the 'boot' drive?
View 2 Replies
View Related
Feb 23, 2011
I have a laptop which have vista,fedora 12. Today i have install another operating system ubuntu in my laptop. But when i restart it, it not boot up and show black screen. how to resolve this
View 1 Replies
View Related
Jul 30, 2010
Have you had to download drivers for GNU/Linux and install them when some device didn't work? Except nVidia/ATi drivers I mean. Just like in Windows. Or the only driver you can download for GNU/Linux is a driver for videocard and all other are in always in the system?
View 4 Replies
View Related
Mar 11, 2011
I have a Xerox printer, Phaser 3160. On the cd that comes with the printer i got a file for linux called "P3160.tar.gz".
Having extracted this file I found the content as listed below:
These are the files in the linux dir,nothing in the other dirs
Below are dirs
As there is no ./configure file, what do i have to do to install the drivers for the printer
I am using Suse 11.3
View 1 Replies
View Related
Nov 5, 2010
I can't seem to get my adapter to work on my Debian Squeeze system. I have the wpc54g linksys notebook adapter and disk... but the disk will not autorun...I have gotten as far as to the adapter being activated, shows connection 97%, but I can't surf!
View 6 Replies
View Related
Feb 24, 2010
I'm booting from disc on a compaq presario F700. Somehow, I messed everything up and now it's not reading that I have an OS. Which was previously vista. Now, when I boot from disc and try to install no partitions come up. I did open the blasted thing to clean it not too long but as far as I know, nothing dislodged. It is a laptop, btw. So, my kneejerk reaction is that the hard-drive got damaged or knocked loose. I also tried using kill-drive to erase it so I could start fresh, also no Hard drive detected. So, I'm going to try that. In the meantime I have another issue. When booting from disc I can't seem to get the drivers for my wireless adapter to install. I have them. Madwifi for AR5001X but I don't know where to put them via terminal.
View 9 Replies
View Related
Mar 2, 2009
i have just installed Fedora 10 and now my wireless adapter doesn't work and i think it's because i need to install drivers for it.. I have been using Ubuntu for the last few weeks and it worked fine in ubuntu probably because ubuntu comes with drivers for my adapter already installed.. Now, i'm kind of newbie so i don't know where to look and what to do.I did lspci and here is my adapter.. Ethernet controller: Atheros Communications Inc. AR242x 802.11abg Wireless PCI Express Adapter (rev 01)
View 1 Replies
View Related
Mar 18, 2010
I can't seem to find drivers for my wireless adapter, TL-WN722NC, so that it can work on Linux (Ubuntu). I have already emailed the company, TP-Link, and they said that it does not support Linux yet.Is there a way that I might be able to get drivers for it somewhere else?
View 5 Replies
View Related
Feb 27, 2010
How to establish a VPN connection,The details I get to connect the VPN are ipaddreess ,username/password How to install WiFi drivers on RHEL5
View 1 Replies
View Related
Jun 10, 2011
We have the need to install an older Linux distribution (Suse 10) on a brand new laptop. The kernel that comes with Suse 10 doesn't have new enough drivers for the NIC and the drive controller. We've been able to find the source code for the NIC and build a working NIC kernel module however, we can not find the source code for the drive controller outside the kernel tree. Newer kernels see the drive fine; the controller is the Intel ATA_PIIX. Its included in the kernel, the hardware we have it just newer than the version in the old suse 10 kernel supports. I've crawled all over the intel site looking for the code outside the kernel source and have been unable to do so. Is it possible to lift the code from a newer kernel source tree? Is it available for download anywhere?
Edit: (from a comment below) SLED-10-SP2-x86 is the OS. The installation of these systems in an automated process, trying to change the process to include a VM (if we had the memory) or install a different base OS; while doable- can't be done in the time allowed. To get through process development, testing, UAT, staging and deployment takes much longer than the time we have. The old laptop had this same issue and the fix by my predecessor was building the NIC and drive modules by hand. We need to simply update those modules for this new laptop
View 3 Replies
View Related
Aug 9, 2010
I have a DWA-130C (external wireless) and am trying to install the drivers for us in Linux Mint, I'm assuming this is done with ndiswrapper, but I have no idea what I'm doing. I am a begginer to Linux though I know the basics of using the console, packages and such.
View 2 Replies
View Related
Jul 20, 2011
I have two devices (a usb modem and a camera) permanently hard-wired into my system. When linux boots, it automatically inserts their drivers. However, I would like this to be under my control to insert as and when needed. Can anyone give any pointers as to how I might disable auto-insertion, whilst still allowing manual insertion via insmod or modprobe? I understand the usual method would be to use modules.conf, however in my modules.conf file, there is no entries at all.
View 1 Replies
View Related
May 2, 2010
I am new to Linux and actually just finished my install about 30 minutes ago. Ubuntu 10.04 isn't recognizing my wireless adapter, so I need to install the drivers. I know where the drivers are, I just don't know how to install them on a Linux system.
Here is the driver page. I don't know how to download the .inf file (necessary?) but I have ndiswrapper, bcmwl5.sys, and sp33008.exe all in the downloads folder.
Apparently just double clicking the files does nothing, so what do I do now?
View 3 Replies
View Related
Jun 30, 2010
I've installed it and it looks great. my problem is that I cant connect to the net since I could not find the driver for my onboard network adapter. it is a Gigabyte GA 945 GCM S2L board. of coarse I searched their site but it says that Linux driver I have to achieve from 3rd party. the adapter's chipset is a Realtek RTL 8111C but I could not find the driver for it. the only one that I've found - doesn't work. I must point out that when I've searched driver for my Nvidia display adapter- I've found it on Nvidia's site and it works great.
View 2 Replies
View Related
Jul 14, 2010
i was given a new DLink DWA-130 REV E draft N usb wireless adapter and was wondering if there are linux drivers for it?
View 2 Replies
View Related
