I have recently installed Linux Mint 10 on my laptop. When I look at the Device Manager in Windows 7, it says I have an Atheros AR9285 Wireless Network Adapter. Right now, I am unable to connect to wifi with Linux. What drivers am I able to install, and how would I install them?
I own an ASUS N61JV-X2 notebook PC. It has an Atheros Communication, Inc. AR9285 Wireless Network Adapter. 03:00.0 Network controller: Atheros Communications Inc. AR9285 Wireless Network Adapter (PCI-Express) (rev 01) 03:00.0 0280: 168c:002b (rev 01) I cannot see any SSIDs including my home Verizon FiOS 802.11 G WPA2-AES-TKIP encrypted network. I went to Starbucks to try to connect to their free Wi-Fi and I could not make a connection. How do I solve this problem so that I can connect to a SSID of my choice and make a wireless connection while using GNOME 3?
installing my wireless card Atheros AR9285.I have tried to get it working with both compat wireless - Ath9k driver but I dont know exactly how to do.I have also tried to get it to work with ndiswrapper, but it is really tricky because nothing is available in centos like precompiled ndiswrapper.I used to work with Arch Linux so everything in Centos is totally new to me and I don�t understand a thing:I need to get it to work as soon as possible.What I have read the should go to just "activate" the ath9k driver with my card and it would work,
I recently reformatted and dual partitioned to both Windows 7 as well as ubuntu 10.10. Loading works fine and Windows 7 is 100% operational. I cannot seem to get my wireless network adapter to be read by Ubuntus 'Windows Wireless Drivers' gui. Here are the steps that I have done THUS far, to make sure that we are all on the right path. Before I go any further, my wireless network adapter is an old school WUSB11 Linksys Wireless Network Adapter (running version 2.6).
1) Downloaded and installed "ndiswrapper" from ubuntu's main website. I downloaded the common, utils and ndisgtk files and installed them accordingly. 2) I extracted these three files to the desktop of Ubuntu and accessed the terminal page. 3) From terminal I typed "cd Desktop" to change the directory to the desktop. 4) Next, I typed in "Sudo dpkg -i ndiswrapper-common_1.54-2ubuntu1_all.deb Sudo dpkg -i ndiswrapper-utils-1.9_1.54-2ubuntu1_i386.deb Sudo dpkg -i ndisgtk_0.8.5-1_i386.deb" 5) This installed Windows Wireless Drivers gui successfully and I can access it. 6) I have downloaded the driver files for the adapter from the cisco website and searched them for the required files needed. 7) After extracting the .INF file from the "Drivers" directory named "NETUSB.SYS" (I wasn't sure if the other associated files within the same folder needed to be present together with NETUSB so I moved everything to the desktop) I typed in "sudo ndiswrapper -i NETUSB.inf". After accessing the Windows Wireless Drivers gui I have noticed that the 'netusb' driver is present yet under it, the system states "Hardware present: No". This leads me to believe that maybe I installed incorrectly or my "fireware?" is not present? I was reading through the installation guide posted on the ubuntu website that in addition to the .INF file we also need the BIN file(s)? and SYS file(s)?.. The folder with the drivers for my adapter contains a BIN file but it is not within the "Drivers" section of the folder. 9) Upon mousing over the network Icon naturally my hardware is still not present. 10) From what I gather after the system finds the hardware I am to write into the terminal
I'm facing problems with Fedora13 and the AR9285 wifi card... the connection is just too slow, and the wired connection works fine. I just figured out that a lot of VAIO users (so am I) were in the same situation, and solved their problem by downloading ath9k drivers from linuxwireless.org. Fine, I did it! That's what I found :
Building and installing cd /path/to/compat-wireless-2.6.32-rc5 ./scripts/driver-select <driver-name> make sudo make install
...but make is looking for source files in /usr/src/kernels/2.6.34-7-61.fc13.x86_64/build/ , which doesn't exist! The /usr/src/kernels/ folder is just empty. I also found something about the fact that Fedora13 didn't came with kernel's source files... So how can I install that driver? (I didn't find the package via yum...)
I bought this new computer with an Atheros AR9285 wireless adapter, signal dropped out after a couple of minutes, sometimes reconnected, I looked up different posts on [URL] and [URL].
First I installed linux-backports and linux-backports-wireless, still dropped. Then I installed compat-wireless-2.6.33 and it still dropped. Finalley I blacklisted the driver with gksu gedit /etc/modprobe.d/blacklist-ath_pci.conf and it still drops. What should I do, it seems to pick it up again after 30 sec or so, but it a bit frustrating.
P.S.: It seems to be getting much better now that I have the torrent program shut down.
I've a big trouble that curses me for months. I've an Asus K52Jc laptop with wireless card Atheros AR9285, Ubuntu 10.10 and this network set-up: a WDSL (so an antenna on my house) wired to a switch; the switch shares connection through 2 ethernets cables: one to my uncle house, one to my router Netgear DG834v5.If I connect my laptop via ethernet, internet works good, if I connect to my router, wireless works (I can ping my router), but no internet. I've been helped a lot in official ubuntu chat: after some tries we understood that the problem aren't drivers, isn't Netgear, but probably it's something messed up in routes or arp cache.Anyway note that I have also some difficulties to ping my router, on 3 tries he often loses 1 or 2 packets.
I have a Belkin Enhanced Wireless USB Network Adapter Model # F6D4050 v2. The drivers are for windows but the windows wireless drivers app doesnt work. I see a tutorial for a linksys that appears to have the same chipset, but I am not sure if any of the steps need to be modified, also my kernel is a bit different. Here is my kernel:
I have a Toshiba MX35 laptop it's a little old but does the job. I'm have a problem getting the wireless to work. I can boot a live CD either Ubuntu 10.10 or Fedora 14 and they will see the wireless card. The card is Atheros Communications Inc. Atheros AR5001X+ Wireless Network Adapter (rev 01).
I have Ubuntu 9.10 installed and that is the OS that is having the problem seeing the wireless. The computer will not handle Ubuntu 10.10 (at least it won't handle the desktop effects under Ubuntu 10.10) but handles them just fine under 9.10 and that's why I have 9.10 installed. I really need the Wifi to work because I'm going to travel in a few days.
I have a Samsung N150 netbook with Atheros AR 9285 WiFi card. I installed Ubuntu 9.10 on it, although this problem happens on other distros too (Network Remix 9.10, OpenSuse 11.2) My wifi card and networks get detected. The problem is when I try to connect to my network, which is protected by WPA key (I don't know if it matters whether it's WPA or not). After I input my network key, the network manager is trying to connect, but obviously cannot, because just prompts me for password again. I can connect without problems to this network from my other computer running WinXP
I recently switched from Windows XP to a clean install Ubuntu Karmic Koala 9.10 but it seems to be quite a problem to get the wifi up and running. In Windows the nearby network all appeared in network connections but the same section in Ubuntu is empty. So I decided to go with the ndiswrapper guide to solve the problem with an unclaimed driver. After an entire day messing with my computer I'm still not close... Below follows excerpts taken from the Ndiswrapper guide with posted results from my computer. "ndiswrapper won't work until it thinks that your Windows drivers have been properly installed and that they are the appropriate ones for your wireless card. You can run the command: ndiswrapper -l"
WARNING: All config files need .conf: /etc/modprobe.d/blacklist, it will be ignored in a future release. WARNING: All config files need .conf: /etc/modprobe.d/ndiswrapper, it will be ignored in a future release. net5211 : driver installed device (168C:0013) present (alternate driver: ath5k)
So I've posted the result the name of my wireless card below: lspci -nn
00:00.0 Host bridge : VIA Technologies, Inc. CN333/CN400/PM880 Host Bridge [1106:0259] 00:00.1 Host bridge : VIA Technologies, Inc. CN333/CN400/PM880 Host Bridge [1106:1259]
It seems like the network is disabled or unclaimed or both. What to do? I'm stuck after spending an entire day trying to install the wifi. I had no problems in Windows XP but it seems to be quite impossible in Ubuntu.
I had U10.10 installed prior to running U10.10 Desktop, and the wlan worked flawlessly on that.My understanding is that the packages are the same and so this should be installed with Desktop, however it will not action the final connection. The wlan is finding networks and prompts for the Key when connecting, but it never actually connects.
Quote: sudo lshw -C network gives the following: Quote: *-network
I have been running FC8 on this IBM T23 with a D-Link wireless adapter. Using MadWifi this has worked fine with Network Manager disabled. But now I have nuked that installation and replaced it with FC10. Network Manager is nice, and I would like to use it. And it kind-of works. Network Manager recognizes my router and all my neighbor's routers, but I can't connect.
I have a old mac G4 and I just recently installed ubuntu 10.10 on it. It doesn't recognize my wireless adapter at all so I get no wireless on the computer. I've never used any linux distribution in my life so I don't have any idea how to install drivers for it.
I can't post messages, I think something is wring with my internet.Anyway, I'm gonna copy paste what I've been trying to say...I just bought the TP-LINK Model No. TL-WN821N. It's an atheros. And I was wondering where can I find the drivers for Linux. It only includes drivers for Windows.
I don't have much experience with networks,I found this website,
I got stuck in the patch section, I don't know what they are trying to say. They are using
I have Fedora11 running in my machine and it has no LAN port (RJ-45). I have a wireless PCMCIA card.The model of the wireless card is NL-2511CD EXT2(ETSI).When I insert that card to the PCMCIA slot a window pops up and ask for a WEP key. My wireless router is configured with WPA but above pop-up has no WPA option. I suspect my fedora installation does not have the necessary driver for my wireless card.I want to install that driver. I can transfer that file to the machine via thumb drive since it has no network connection yet. How do I install this? Please refer below images as I'm still a newbie at linux.
I installed the b43 drivers to enable the monitor mode for using kismet. but after installing, it shows "Device not Ready".
The dmesg | grep b43 output shows: [ 86.449430] b43 ssb0:0: firmware: requesting b43/ucode15.fw [ 146.449335] b43 ssb0:0: firmware: requesting b43-open/ucode15.fw [ 206.448146] b43-phy0 ERROR: Firmware file "b43/ucode15.fw" not found [ 206.448153] b43-phy0 ERROR: Firmware file "b43-open/ucode15.fw" not found [ 206.448158] b43-phy0 ERROR: You must go to [URL] and download the correct firmware for this driver version. Please carefully read all instructions on this website. How to re-enable my wireless connection.
I'm booting from disc on a compaq presario F700. Somehow, I messed everything up and now it's not reading that I have an OS. Which was previously vista. Now, when I boot from disc and try to install no partitions come up. I did open the blasted thing to clean it not too long but as far as I know, nothing dislodged. It is a laptop, btw. So, my kneejerk reaction is that the hard-drive got damaged or knocked loose. I also tried using kill-drive to erase it so I could start fresh, also no Hard drive detected. So, I'm going to try that. In the meantime I have another issue. When booting from disc I can't seem to get the drivers for my wireless adapter to install. I have them. Madwifi for AR5001X but I don't know where to put them via terminal.
i have just installed Fedora 10 and now my wireless adapter doesn't work and i think it's because i need to install drivers for it.. I have been using Ubuntu for the last few weeks and it worked fine in ubuntu probably because ubuntu comes with drivers for my adapter already installed.. Now, i'm kind of newbie so i don't know where to look and what to do.I did lspci and here is my adapter.. Ethernet controller: Atheros Communications Inc. AR242x 802.11abg Wireless PCI Express Adapter (rev 01)
I can't seem to find drivers for my wireless adapter, TL-WN722NC, so that it can work on Linux (Ubuntu). I have already emailed the company, TP-Link, and they said that it does not support Linux yet.Is there a way that I might be able to get drivers for it somewhere else?
I am new to Linux and actually just finished my install about 30 minutes ago. Ubuntu 10.04 isn't recognizing my wireless adapter, so I need to install the drivers. I know where the drivers are, I just don't know how to install them on a Linux system.
Here is the driver page. I don't know how to download the .inf file (necessary?) but I have ndiswrapper, bcmwl5.sys, and sp33008.exe all in the downloads folder.
Apparently just double clicking the files does nothing, so what do I do now?