Ubuntu Installation :: Add Ahci Drivers For 11.04?
May 18, 2011
I recently decided to install Ubuntu 11.04 on a 320gb hitachi sata hard drive. This is going into a new system with an Asus MB, AMD Proc, not sure if this matters. Anyway I can not set the bios to use ahci and see the sata drive. I can only use IDE mode with sata enabled. Asus support says to install ahci for os. If I boot into the USB install key and attempt to the install OS I receive a read/write error. I have another drive on IDE that has 11.04 on it and if I try to format the new drive and partition it with Disk Utility it fails with "Error formatting drive: error creating partition table: helper exited with exit code 1: error calling fsync(2) on /dev/sdb: Input/output error". I have tried to use dd and fdisk but I don't believe I need these until I do something else first just not sure how or where to look.
View 6 Replies
ADVERTISEMENT
Jan 16, 2011
I had a problem while installing linux 4.0, 5.0 & 5.2
My system configuration is as follows:
MSI 785 GM E65 MotherBoard
AMD Phenom IIx2 550 processor
RAM 2GB Kingston DDR3 1033GHz
HDD 1TB
While Installing linux 4.0 it shows a msg AHCI adapter drivers not available and system halts
While installing linux 5.0 it shows a msg
KERNEL PANNIC and system halts
While intalling linux 5.2 it halts
View 7 Replies
View Related
Mar 10, 2010
I want to install Ubuntu x86_64 or x86 to my computer.
I used Dekstop and Server Editions on other machines, installed succesfully but i could not install Ubuntu to my computer.
My hardwares are;
AMD Phenom II X4
Gigabyte GA-MA790GP-DS4h [SB750 - AMD AHCI Compatible RAID Controller]
2 x 250GB Seagate ST3250410AS @ Raid0
I installed Windows succesfully and i created 50GB partition for Ubuntu.
I tried to install Ubuntu, but disks are not detected in partition managing screen.
how can i install ubuntu?
View 5 Replies
View Related
Mar 24, 2011
In order for TRIM to work on an SSD with encryption, I need to make sure to "select the AHCI option before installing the operating system."Does anybody know how to do this? I have no idea what this is talking about. I'll be installing 11.04 with no dual-boot. Just Ubuntu alone.
View 9 Replies
View Related
Aug 19, 2010
I am about to do a clean install of 10.04 (64-bit) on a ThinkPad X201. The machine will only be running Ubuntu (i.e., no dual-boot). Is there any reason to use compatibility mode for the SATA boot drive, or will AHCI work fine?
View 2 Replies
View Related
Jun 10, 2009
Server has DQ35JO board, 8GB memory, multiple SATA hard drives. It was happily running Fedora 10, and Fedora 9 before that. I downloaded and burned the F11 DVD, booted it, did an install which is:
-- delete the LVMs
-- create a 200 MB /boot on ext3, the rest of /dev/sda on ext3 as /
-- reformat the swap partition on /dev/sdb1
-- leave the other file systems alone (they are all ext3)
I chose no optional packages and let it install. It finished normally and got to the "click to reboot" screen. Now, my server is completely bricked. When I power it up I get a blank screen with a blinking cursor. I cannot even get to the BIOS, or boot my Fedora DVD, much less boot the boot drive.
View 6 Replies
View Related
May 7, 2010
Here is my problem: In short, it takes forever (6 min), and lots of prodding to get Ubuntu to boot. Im running a Toshiba NB305 netbook (Bios 1.40), set up for dual boot with 10.04 UNR. Windows partitions boot fine. Can boot 10.04 from USB stick.
Here how I try to boot: From grub menu select "Ubuntu, with Linux 2.6.32-22-generic" If it doesn't work, I run the recovery version, and then run the regular one again. Somehow that resets stuff.
[Code]...
View 1 Replies
View Related
Dec 1, 2010
If I change my sata mode from IDE to AHCI grub won't show (cursor goes to top left) when I power on my system. After that, I press the reset button and my grub shows ok.
So, to use AHCI I always have to use the reset switch button.
Using Ubuntu 10.10 with 2.6.35-23-generic - 64bits
View 5 Replies
View Related
Feb 28, 2011
I have been running a dual-boot, Windows 7 and Ubuntu 10.10 system with the disks set for IDE with no problems. I have just attempted to change the disk system to AHCI and, whilst I can boot into Windows 7, I am unable to boot into Linux and get the error: "Alert! /dev/disk/by-uuid/5d773307-a046-40fa-ba29-728611bc7eed does not exist" I am new to Linux so am unsure where to go from here. I have reverted to IDE for the moment and it boots Ok.
View 3 Replies
View Related
May 12, 2011
I'm doing a clean install on a new machine, and when I tried to boot the install DVD, ISOLinux gave me the following error:
Code:
Could not find kernel image: linux After some experimentation, I found that switching the SATA mode in the BIOS from AHCI to Native IDE solved the problem and installation is proceeding normally.
However, I want AHCI enabled. (I think, unless someone has a compelling reason why I shouldn't.) My web-searching suggests that if the system is installed in IDE mode, it won't boot if I switch to AHCI afterwards. Is this a common problem? Is there a workaround? Is it a motherboard issue?
View 3 Replies
View Related
Apr 23, 2010
/sbin/udevd --daemon eats about 10-15% of cpu which is quite high. I found out that it is caused by AHCI. If I turn it off in bios, udev takes only about 0-1% of cpu (which I consider normal). However turning AHCI off is deadly for Windows Vista (I have dual boot) - it always ends up with BSOD. Actually, I don't even know what AHCI does. Of course I found some information on the net but I didn't found whether there are some advantages for me. Is it worth 10-15% of cpu (consequently shorter battery life)? On the other hand, I have no interest in changing my bios settings every time I boot to Windows so it would be much confortable to have it turned on all the time. The best solution would be to find out why AHCI does this and how to configure udev to avoid it. And I don't know how.I have OpenSuse 11.2, kernel 2.6.31.12
View 1 Replies
View Related
Jan 20, 2010
How can I force my kernel to use the ahci driver when both the ahci & sata_nv are built into the kernel.?
My MSI board bios doesn't have an option for "AHCI MODE". The only sata option that it has is "called "On Chip Sata" & is located under "Integrated Peripherals. Also, the only values available for "On Chip Sata" are enabled or disabled. If I choose the disabled option, the sata drives arn't found & bootup fails.
I tried to tell the kernel to use the ahci driver by appending kernel options to my Grub2 bootloader but they all failed.
(eg.) ahci, scsi=ahci, ata=ahci, ahci.=0 sd=ahci
sata_nv=no, sata_nv=0, sata_nv=none
The only thing I can think of that is left to do is to re-build my kernel with CONFIG_SATA_NV as a loadable module & CONFIG_AHCI as a build-in driver. With only the ahci driver available at boot, the kernel will have to use it or fail to boot.
One more thing I want to say is that my other computer with the ASUS motherboard uses the ahci driver & I have both the sata_via & the ahci drivers built into the kernel. However, it has a bios option for AHCI MODE.
(eg.) Southbridge VT8251
Serial ATA IDE Controller <AHCI>
View 8 Replies
View Related
Nov 12, 2010
One of my 2 harddisks, a Hitachi HDS72101, is very slow, the driver is ahci.
Output of "hdparm -t /dev/sda":
/dev/sda:
Timing buffered disk reads: 8 MB in 3.20 seconds = 2.50 MB/sec
No problem with the other one, a Hitachi HDS72161, the driver is pata_ali.
Output of "hdparm -t /dev/sdb":
/dev/sdb:
Timing buffered disk reads: 224 MB in 3.00 seconds = 74.63 MB/sec
How could I get better performance for /dev/sda ?
My system: openSUSE-11.3 on amd64
View 9 Replies
View Related
Apr 29, 2011
Do I need to add any special options to mkinitrd for AHCI configuration?
mkinitrd -c -k 2.6.37.6-smp -m ext4
Does it know I'm not in legacy PATA mode or do I have to add something to load AHCI module with it?
View 3 Replies
View Related
Nov 30, 2009
I am using openSuSE 11.2 on a VGN-AR41L. I have also erased the preinstalled Home Vista (what a pleasure). Now to my problem. My system boots correctly but if I press the <ESC> key while booting I can see the following messages:
"Doing fast boot
FATAL: mbcache module not found
FATAL: ahci module not found
"
and the boot process continues normally.
Why this happens? Does this mean that I have a problem that I haven't discovered yet? Is it something that I can ignore? I am using SUSE Linux from version SUSE Linux 8 personal and although I am not a power user I have done my two desertions on this system and I am very happy with SUSE. I have bought SUSE Linux 8 Personal and SUSE Linux 10 all the other versions until today have been downloaded.
View 6 Replies
View Related
Apr 16, 2010
I have a HP Pavilion dv7-2230sa During boot I get a series of errors about ACPI and AHCI Conflicts, the result of which I have to dissable ACPI with acpi=off. However when acpi=off my wireless Broadcom b43 series refuses to enable the wifi. I just can't press the button that would enable / dissable the wifi.
The wifi is detected, the drivers and firmware are installed, however the light remains firmly in the RED.the ethernet works, sound works fine, There also seems to be an issue with the ATi/Radeon Driver being missing which is causing fatal errors at boot time and also some memory conflicts again causing fatal errors.
I have tried this laptop under opensuse 11.2 and now under opensuse 11.3M5 without sucsess - however to my dislike Ubuntu have managed to resolve this by accident between 9.4 and 9.10 but i wanna use opensuse not ubuntu i have asked them to tell me how they fixed it to share it with you but I am still plowing my way through their forum!
[Code]...
View 9 Replies
View Related
May 9, 2010
I want to run my Debian install in AHCI mode on my computer. It runs perfectly fine, all drivers etc work perfectly also. The computer itself is in RAID mode but with all 4 RAID channels disabled (I refuse to use any RAID arrays because I simply don't like them). However, my computer (Acer Aspire m3640/m5640, motherboard MCP73PV/630i) has greyed out the option for me to change the option from RAID mode to either IDE or AHCI. Since I do not use RAID at all, I want to change to AHCI but it is greyed out in the BIOS. This option wasn't greyed out before as far as I remember.
I also have Vista x64 installed on a SATA drive along with Debian all partitioned. I also have an empty IDE drive attached which will be used for another operating system AFTER I have changed to AHCI mode. The SATA drive has the boot flag. I use GRUB to boot the operating system. My BIOS version from American Megatrends is R01-A3 (not the latest one, but the one I need to use). My question is this, how could one possibly go about as to changing it to AHCI mode from RAID with the BIOS greying the option out. how to make the BIOS ungrey the option (if there is another option preventing it from being changed or if the harddrives need configuring etc). I am not particularly concerned if the drives need to be wiped.
View 8 Replies
View Related
Apr 7, 2010
I realized after spending some time performance tuning my mini Linux server that the hard drive is stuck in IDE mode, and I can't get the controller to be discovered in AHCI mode.EDIT: I should add that I'm running Vector Linux 6.0 Lite, which is based on Slackware 13.0. The Kernel version is 2.6.27.12.
The mobo in question is actually a small mini-ITX board from Foxconn. Here is a links to the specs:url.I use it for a media server, and so far the drive I'm using (Hitachi HDE721010SLA330) is working fine in IDE mode (apparently).
I have a strong suspicion that the crappy Foxconn BIOS supplied with the board is not initializing the Intel 945GC controller in AHCI mode. There is a BIOS entry for setting the controller to "Advanced", but I don't think it's doing the job.
Here is an "lspci -vvnn" of my system:
Code:
00:00.0 Host bridge [0600]: Intel Corporation 82945G/GZ/P/PL Memory Controller Hub [8086:2770] (rev 02)
Subsystem: Foxconn International, Inc. Unknown device [105b:0d4d]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ >SERR- <PERR- INTx-
Latency: 0
code....
Is there anything I can do to get the drive/controller in ahci mode, or is the BIOS screwing me?
View 3 Replies
View Related
Nov 26, 2009
I am using Centos 5.4 on an Intel DG451D Main Board. Two SATA drives in RAID1 mode via the main board's built in AHCI controller. It seems to work just fine but I would like to be able to monitor the state of my drives and controller, especially during a re-build and make configuration changes etc if possible, so new drives can be added etc from within the OS. Is there a way to do this within Centos or am I stuck with using just the BIOS configuration system? Apologies if this is a stupid question - I am pretty new to this and have spent several hours trying to find a solution to my question but to no avail.
View 1 Replies
View Related
Sep 28, 2009
Yesterday I was on my Windows computer doing homework. Once Football came on, I hit the Standby button on my keyboard and walked out of my room. Came back at halftime to discover that my system never went into Standby. I turned on my monitor and saw a bunch of code repeating. I don't remember it all, but it was something to this effect
Super Block not compatible with current BIOS
scanning for *insert system file here*.... not found
scanning for floppy drive... not found
scanning for cdrom1... not found
So I hit the restart button on my tower. When it restarted, I was brought back to the same screen. So I unplugged the power cord from my computer and counted to 10. I plugged it back in and this time I got my mobo logo screen and the system appeared to start up fine, until I got to the SATA drive scanning screen. When my computer would scan for my SATA hard drive, it would idle for several minutes, during which a series of periods (".") would show up until eventually I get a message that says: WARNING! - Something wrong with your hardware!
I have troubleshooted a number of things so far:
1) I took my SATA Hard Drive out of my computer and plugged it into my Linux computer and the system booted fine! I used the same SATA cord, so I know both the drive and the cord ARE WORKING!
2) I tested the power cord from the power supply that runs to my HD and it is working just fine.
3) I plugged the HD back into my Windows computer (the original one it was in when I started having this problem) and I ran GParted. When the GUI came on, I could not see any drives and there was a message at the bottom of the window saying that no devices could be found. This was no surprise to me because I watched the verbose mode as GParted booted and it gave error messages when it tried scanning for my hard drive.
4) I have also tried plugging it into the other SATA ports on my motherboard.
5) I tried flashing the mobo BIOS. The flash worked just fine (or at least it appeared so), but the HD is still not being found on the system boot scan.
Bottom line, I know the hard drive is fine because it worked in my Linux computer. So I am thinking it has to be the motherboard. But before I go out and buy a new Mobo and CPU (and possibly new RAM), I wanted to quickly jump on here.
View 1 Replies
View Related
Dec 15, 2010
I have successfully installed a dual boot system with Fedora 14 on drive sdb and WIN7 on drive sda, with Fedora 14 being the major (default) OS. The system is an AM3 with a quad core CPU and all SATA drives. The drives are set to IDE mode, and I am wondering:-
1. What are the benefits of AHCI - will it improve the speed and responsiveness of my system? And
2. If it is worth installing, do I have to do a complete re-install of the OS, or is there some way of updating the installed Fedora to include and operate with AHCI mode drives?
I'm quite happy with the system as it is now, but if there is a way to squeeze extra speed out of it I'm willing to give it a go. And never having been involved with SATA drives and Linux previously, I'm completely ignorant on the subject.
View 2 Replies
View Related
Apr 8, 2010
I have been using ubuntu for quite a long time, and for the first time, I am now unable to set nvidia drivers to work. I have just install ubuntu 9.10 amd64 on an AMD 64 athlong X2 with a GEForce 6500 nvidia card.
The only reason I need the proprietary drivers is to use two monitors.
I am going crazy, I have tested everything I have found on the web. I have tried all the nvidia drivers version, I have tried envyng, ... but nvidia do not work!!
I am trying Xinerama with nv, but it does not work either!!!
Here is my xorg.conf file in which I have tried to use nv driver to set dual monitor. X fails to load and it says that screen 0 is deleted, that devices are found but there are no matches in the config file. Any clue?
Section "Files"
ModulePath "/usr/lib/xorg/modules"
FontPath "/usr/share/fonts/X11/misc"
FontPath "/usr/share/fonts/X11/cyrillic"
FontPath "/usr/share/fonts/X11/100dpi/:unscaled"
FontPath "/usr/share/fonts/X11/75dpi/:unscaled"
[Code]....
View 3 Replies
View Related
May 8, 2010
I know i know, some will say "eww Proprietary Drivers" but hey, ubunt is all about having more control of the OS. Is there an easy way to install Proprietary Drivers thats not through the hardware drivers option on system?
View 2 Replies
View Related
Jul 13, 2010
I installed Xubuntu the other night (completely wiped machine) and started doing all the updates on it. After a couple of reboots, I changed from the proprietary drivers, to the regular nVidia drivers. After doing this, the startup logo is displayed at a really low resolution. Is there a simple fix to change this and use the nVidia drivers as well?
View 1 Replies
View Related
Jun 27, 2010
I've installed Ubuntu Netbook 10.04 on my HP DV2000 laptop and now I want to get my wireless to work by installing the proprietary broadcom drivers (4311, I think). But my internet doesn't work yet obviously, so I need to download the drivers to my thumb drive on my desktop and install them on my non-networked laptop.My issue is that I don't know:a) Where to get the driversb) How to install them from a local drive
View 2 Replies
View Related
Oct 24, 2009
I just installed Karmic beta and I'm having issues with getting my wireless driver to work. When I was using 9.04 and when I booted 9.10 from a CD, I could just go to System > Administration > Hardware Drivers and activate a wireless driver and everything would be just peachy. The problem is that, in the install of 9.10 beta, no drivers appear when I load the Hardware Drivers GUI, so I can't get wireless internet.
Is there anything I can do besides wait a few days for the full release of 9.10 and hope that solves the issue?
View 5 Replies
View Related
Jan 17, 2010
I need VGA drivers for ubuntu 8.10. System configuration as follows-
INTEL DG102Ggc2 (945) board.
dual core 2.67ghz.
512DDR2 RAM.
View 2 Replies
View Related
Feb 6, 2010
HOW TO GET 3d with the XF86-ati-driver
install from source the 2.6.32-r2 kernel
upgrade Xorg-server to 2.17.999
install from git libDRM-2.4.17
install from git mesa-7.7
install from git the xf86-ati-driver-9999
unless you KNOW what you are doing dont do this, you will also have to recompile KDE/gnome ( so I guess you have to install that from git as well )ooo I forgot the reason why I posted this. Doing this is NOT worth it, I did it and when I went to play a 3d game it renders shadows poorly and some reflections are rendered upside down.If you want 3d accelleration with an ATI card, you MUST install the FGLRX proprietary driver.
View 1 Replies
View Related
May 14, 2010
download the newest 64 bit driver via gui? as after my upgrade from 9.10 i am stuck with gui..i found codes for installing it in gui so that should be ok, but ive not found any codes for downloading it..although from what ive seen it should not be too hard..
View 4 Replies
View Related
Sep 2, 2010
i have a atheros ar5b93 card and i was wondering were you got the driver i asked around and none knew where its located
View 2 Replies
View Related
