General :: Broadcom BCM4328 Wireless Adapter Not Supporting Monitor Mode Using WL And B44?
Feb 8, 2009
A friend of mine has a Dell XPS1530 lappy that has a broadcom bcm4328 wireless adapter. I tried installing kismet on it so I can scan for wireless network in range. I configured it with the source driver as bcm43xx in kismet.conf and complained that the driver didn't support monitor mode. It uses the proprietary 'wl' kernel module to operate but kismet can't use the 'wl' module and it says the same error. I tried unloding the wl and b44 modules and loding the b43 driver but then the adapter stoped working. I searched on the net a bit and found out that kisment doesn't work with the prorpietary drivers for that card.
View 14 Replies
ADVERTISEMENT
Dec 31, 2009
I have a dell mp1210 xps laptop. I just recently installed installed Ubuntu 9.10 and am very green. With difficulty I managed to install the drivers for the wireless card and now have wireless on the laptop. In order to get the wireless working I had to restart my computer, and once it booted up again the wireless works, but there is no trace of eth0-my wired network device (Broadcom BCM4401-B0) which was working fine before I got the wireless adapter working. Lspci still shows the device as it did when it was functioning, but ifconfig only shows my local loopback and wlan0 (my wireless device). I am not sure how eth0 got deleted, I am wondering if maybe I have to set up some sort of switching between the wired and wireless adapters so they are not both active at the same time. Any suggestions would be really nice, I have been digging through the forums, but I am unsure of what went wrong or what to do about it.
View 14 Replies
View Related
Feb 3, 2010
I have been trying to get my Broadcom BCM4328 to work properly on openSUSE 11.2 (kernel 2.6.31.5). Finally, after installing the wl kernel module, I managed to get it working when a run the following commands after a reboot:
sudo /sbin/modprobe -r b43 b44 ssb wl
sudo /sbin/modprobe wl
sudo /sbin/modprobe b44
sudo /etc/init.d/network restart
My question is how can I automate the above commands, i.e. create a startup script to initialise the wireless adapter properly without the need to manually reload the kernel modules?
View 3 Replies
View Related
Mar 2, 2011
I want to do some pen-testing using aircrack-ng on my local network and currently the only wireless adapter I have is the WNA 1100 netgear adapter. I am using the ath9k_htc driver.
View 7 Replies
View Related
Apr 3, 2010
First of all, this tutorial will use NDISWRAPPER, not b43, not wl (Broadcom STA). So, hooray for new method (actually, the only method ). Now, I don't want anyone to get scared because of bad experiences with Ndiswrapper or whatever, it's actually quite easy. I did not come up with any of this info. I'm just putting this guide together from Kacper Szczesniak's info (who came up with this method), WifiDocsDriverbcm43xxFeisty_No-Fluff from the Ubuntu Wiki, and my experience. The Broadcom STA (wl) driver has references to monitor mode in it's code, but does not have that functionality in reality. The Broadcom Windows driver on the other hand does have this capability. So, for monitor mode to work, you will need a patched version of ndiswrapper.
1) Install the Linux kernel headers:
Code:
sudo apt-get install linux-headers-$(uname -r)
2) Install the tools required to compile Ndiswrapper:
Code:
sudo apt-get install checkinstall dh-make fakeroot gcc build-essential
3) Unload current Ndiswrapper module, if running:
Code:
sudo rmmod ndiswrapper
[code]....
View 9 Replies
View Related
Jan 18, 2011
How do I install Broadcom Wi-Fi on Arch Linux in command line mode on an Acer eMachines EM350?
I assume that Broadcom STA should be the driver used and my USB key the way to install it with the help of another PC, assuming that I can't use a RJ45 ethernet connection on LAN.
View 1 Replies
View Related
Feb 21, 2010
I tried Ubuntu before and because the wireless kept giving me error i stopped using linux for a while and now i'm back to give it another try and hopefully stay with linux, so help me out please. thanks in advance.
lspci & lsusb
Code:
ahmad@ubuntu:~$ lspci -nn | grep Broadcom
0b:00.0 Network controller [0280]: Broadcom Corporation BCM4328 802.11a/b/g/n [14e4:4328] (rev 03)
ahmad@ubuntu:~$ lsusb
Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
[Code]...
View 4 Replies
View Related
Feb 7, 2010
I'm installing Squeeze on on a Dell Latitude D830 laptop with a Broadcom BCM4328 wireless network card, and I'm stuck on getting wireless internet to work. I have the 2.6.32-trunk-686-bigmem kernel. I run KDE and I have knetworkmanager installed to sort the network connections out. Unfortunately, knetworkmanager cannot find any wireless networks for eth2 (the wireless adapter). There is a wireless network, as other equipment can still connect to it.
I've installed the broadcom-sta drivers according to http://wiki.debian.org/wl. When I run iwconfig, I receive the following output: eth2 IEEEE 802.11abgn ESSID:"" Mode:Managed Frequency: 2.412 GHz Access Point: Not-Associated Bit Rate: 14 Mb/s Tx-Power:off Retry min limit: 7 RTS thr:off Fragment thr:off Power ManagementMode: All packages received Link Quality=5/5 Signal level=0 dBm Noise Level=0 dBm Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 Tx excessive retries:0 Invalid misc:0 missed beacon:0
[Code]...
View 5 Replies
View Related
Mar 28, 2011
i am using fedora 14 in my lenovo z560 laptop. It contains broadcom wifi card. The configuration is.Network controller [0280]: Broadcom Corporation BCM4313 802.11b/g LP-PHY [14e4:4727] (rev 01) Subsystem: Broadcom Corporation Device [14e4:0510] I want to inject monitor mode in my laptop to run kismet . But i can't. I installed broadcom-wl driver in my laptop but i think its not compatible to run monitor mode..
when i run kismet it show me error that :------ try some other open source kernel driver And the other is :- kismet find only binary value eth1 port. It isn't detecting wlan0 port
View 10 Replies
View Related
Dec 14, 2009
I'm having some issues with openSUSE 11.2 recognizing my Broadcom adapter. Following the instructions in the two stickied topics, I can find the adapter both under YaST's Hardware Summary and using the console command /sbin/lspci. I cannot, however, find it with /sbin/lspci -n, and the boot log (viewed with dmesg | less) makes no mention of it either.
Do I need to turn it on or something? This is a dual boot machine, and it works fine under Windows, so I don't think there's a hardware failure at play here.
View 9 Replies
View Related
Jul 20, 2010
I am running Lucid Lynx, kernel 2.6.32.23 generic, I have a card with the Broadcom BCM4311, with the STA Linux Wireless driver. I have no idea how to get monitor mode to work with the Aircrack-ng suite's Airmon-ng command. I use the command: sudo airmon-ng start eth1
And I get this output: Found 5 processes that could cause trouble. If airodump-ng, aireplay-ng or airtun-ng stops working after a short period of time, you may want to kill (some of) them!
PID Name
883 NetworkManager
893 avahi-daemon
896 avahi-daemon
931 wpa_supplicant
[Code].....
View 4 Replies
View Related
Apr 7, 2010
I have a macbook pro here that I have loaded OPensuse 11.2 onto.
The main problem is that it wont recognise my wireless adaptor.
I have installed the packman repository and installed the broadcom-wl driver.
View 9 Replies
View Related
Mar 20, 2010
I am having problems with the refresh rate if the screen. In the refresh mode of the monitor in the monitor options have only one option 60Hz. I have LG 24 + ATI Radon 3870, and have already installed the ATI driver via Ubuntu download center.
View 1 Replies
View Related
Mar 22, 2010
I can't get my wireless into monitor mode. I;m running ubuntu 9.1 karmic It connects fine to wireless networks. But when i do: sudo iwconfig wlan0 mode monitor. I get: Error for wireless request "Set Mode" (8B06) :SET failed on device wlan0 ; Device or resource busy. I can only see wlan0 (wmaster0, eth0), not ath0 or wifi0 mentioned elsewhere, in wireshark. I only see my own ip and packets coming to and from that. my system tells me i have an atheros ar9285 chipset in place.
View 2 Replies
View Related
Sep 10, 2010
I wants to ask if there is any method to configure bcm4313 wireless adaptor to monitor mode.
I need to do this for my graduate project
till this moment, what I'm sure of is that ndiswrapper doesn't support monitor mode.
Is there any way to use monitor mode on this adaptor?
View 14 Replies
View Related
Mar 25, 2009
I like to test my network often. Until recently, I've been doing so on my old Ubuntu 6.06 laptop... the problem is It's too slow (1.06 GHz single Core ), and old, (designed for Win 2000) to really be effective any more. So, recently I bought a new laptop...one with a Dual core Processor, and twice the speed. Anyway, I'm running Fedora Core 10 X86_64 on it. My problem is as follows:
Although I do have MadWifi installed, for some reason, I still can't put my Atheros based Netgear WPN511 into monitor mode. (in the Network configuration window, it says "Atheros Communications Inc. Atheros AR5001X+" I'm not sure what it means but I'll put it in in case it helps) does MadWifi not work with Fedora? if not, is there a Fedora 10 (X86_64) alternative?
View 8 Replies
View Related
Dec 9, 2010
Running Ubuntu 10.10 on Hp Mini 1030nr My wireless card is a Broadcom BCM4312. I have the b43 driver installed. When I disable networking I can change to monitor mode but then it changes back to manage mode when I enable networking again. I tried using airmonNG but it;s not working.
View 1 Replies
View Related
Feb 9, 2011
I'm a student who is working on a wireless research project. I have a madwifi driver for Atheros chipset on Debian Linux. With having the wireless interface get into monitor mode, I want to forward the captured packets from the wireless interface to the other Ethernet interface so that a different computer which is connected to this machine via Ethernet receives those packets. I checked that alll packets are received in the wireless interface using TCPDUMP. I tried to forward those packets with IPTABLES like 'iptables -p FORWARD -i ath0 -o eth2 -j ACCEPT' However, I couldn't see any packets forwarded to eth2 using TCPDUMP.
View 5 Replies
View Related
Feb 23, 2011
I am having some issues getting the broadcom sta driver installed on Kernels 2.6.36 up through 2.6.38.
Before I continue, I'll list my specs
Release: Xubuntu 10.04.2 LTS (64-Bit)
Wireless Card: Broadcom BCM4328
Kernel: 2.6.38-x (Any version), and 2.6.36 and above
EDIT: Yes! Yes! I got it to work, for those that are having issues, install this packages. Disregard that it says that there is an older version available in a software. The bcmwl-kernel-source for Natty works on Lucid![URL]... Install one of these and check your Hardware Drivers, they will probably say that the Broadcom STA driver is installed but not in use. If you then proceed to restart it should be up and running, this way you can use kernels 2.6.36+ and still use the Broadcom STA driver!
View 1 Replies
View Related
Jul 16, 2011
However I am having some issues with drivers. I need to install a Patriot Wireless N USB wireless adapter in Crunchbang but when I follow the directions for installing the drivers and am using the command "make" I get an error that says '*** /lib/modules/2.6.32-5-amd64/build: No such file or directory. Stop . *** [modules] Error 2"
View 1 Replies
View Related
Feb 2, 2010
I have freshly installed RHEL 5.4 on a Dell Inspiron with WLAN adapter Broadcom 4318. The original driver bcm43xx did not work. So I installed ndiswrapper for using the windows driver.Now I can connect via DHCP, but when I try to assign a static IP address, it still uses the IP address provided by the router (AVM Fritzbox 7270). I always did ifdown/ifup and the static IP and everything else is present in /etc/sysconfig/network-scripts/ifcfg-eth1. But ifconfig always shows the IP address assigned by the router. When I switch off the DHCP server of the router I can't connect to the network anymore. The LAN adapter Broadcom 4400 is working well with a static IP address.
View 3 Replies
View Related
Jan 3, 2010
Basically a few weeks ago I decided to try Linux, in particular Ubuntu. I have it installed in my Windows 7 partition but now I am willing to take the full plunge and switch to it all the way. The only issue is I cannot connect to wireless internet. It states "device not ready". Wireless is turned on on my laptop, I am very near the source, have tried making a manual connection with the network setup. I tried the hardware tester and it found my ethernet and wireless hardware (Broadcom 802.11g Network Adapter).
I went to the package thing and looked for Broadcam. I found a package but it was already installed. I tried it manually with:
sudo apt-get install bcmwl-modaliases
E: Could not get lock /var/lib/dpkg/lock - open (11: Resource temporarily unavailable)
E: Unable to lock the administration directory (/var/lib/dpkg/), is another process using it?
I then heard to try "sudo apt-get install bcm43xx-fwcutter" and did but it couldnt find it.As stated before I am new to linux so I'm probably missing something easy I just beg your patiance as I learn this new operating system.
View 4 Replies
View Related
Feb 8, 2011
When I first installed ubuntu 10.10, the display was for some reason tinted green and shifted a few inches to the right. After experimenting with the resolution preferences, I eventually got it to a large resolution (1280x720 ... or something like that) yet is was quite blurry. I found out that the problem was with my monitor after I switched it to TV mode, then back to PC mode. It became perfectly clear! All I had to do then was adjust the screen positioning by shifting it left a bit.
Even though I have made the resolution I figured out to be default, whenever I turn the PC on after shutting down, it goes back to the "green-and-to-the-side" mode. :/ Ain't really a big problem, until I tried to fiddle with the resolution preferences s'more.
Somehow, I have set it to be twice as wide of the maximum my monitor can display, went back to being green tinted for some reason, and is completely shifted left (yet the right side is still visible) This means that I cannot see what is going on the left side, and cannot adjust the resolution preferences, nor can I click blindly cuz the border is only around my visible side of the screen. Now it is stuck like this.
I've researched many hours and eventually found the terminal command for the resolution preferences. it popped up on the visible side. Although it was to no avail cuz I HAVE TRIED EVERY SETTING AND OPTION and absolutely nothing changed. I assume a system restore would simply revert it back to the previous satisfactory settings, but the thing is I want to FIX it. I am new to this terminal stuff, so I want to learn it and all that. To put it simply, here's what I want:
Learn how to manually adjust resolution without depending on a simple dialog box. Make the satisfactory resolution default and consistent through turning it on and off. Link that could teach me the essential commands, all this googling is stressful. D:
View 3 Replies
View Related
May 25, 2011
Can you "split" a network interface in Ubuntu, similar to how airmon-ng lets you use your wireless card in managed and monitor mode, by making another interface out of the same hardware? I know it'd be slower, but I'd still like to do it.
View 4 Replies
View Related
Jun 19, 2011
i have a broadcom BCM4311 802.11b/g WLAN [14e4:4311] (rev 01) wireless adapter on a dell 1501 run by ubuntu 10.10.this particular model and revision is suppose to be absolutely supported by linux and indeed it did work perfectly before the user ran a upgrade from ubuntu 10.10 to 11.04.subsequently i have reinstalled 10.10. as i recall when i installed ubuntu 10.10 the first time i simply ran the System>Admin>Additional Driver installation tool to make the wireless work. i cannot recall if i ran the b43 or the sta driver but i have tried both this time and had no luck.
i am aware that the broadcom adapters are notoriously troublesome and i have tried the two workarounds here URL... as well as their third alternate workaround with no success.
View 3 Replies
View Related
Feb 22, 2010
I just got a Samsung SyncMaster T260HD monitor. It works straight out of the box with Windows but I can't seem to get it to work with Linux, which is my primary OS for day to day work.
The computer boots up but when going into graphical mode on Linux the monitor gives me a "Mode not supported" error and doesn't display anything.
I booted up windows and, using PowerStrip, grabbed the exact ModeLine that should be used to get the equivalent setting in Linux and added it to my xorg config file but it doesn't seem to help. the ModeLine is:
ModeLine "1920x1200" 153.9 1920 1984 2016 2080 1200 1203 1209 1235 +hsync -vsync
This is the modeline for the working display settings in windows but it doesn't seem to work in Linux My complete entry in the xorg.conf file for the monitor is
Section "Monitor"
Identifier "Monitor0"
ModelName "SyncMaster"
DisplaySize 518 324
[Code]....
I'm running Scientific Linux 5.4 (clone of Redhat Enterprise Linux 5.4) but I've tried booting with a recent Linux Mint Distro as well as Ubuntu 9.04 and had the same problem.
View 1 Replies
View Related
Sep 10, 2010
"Broadcom would like to announce the initial release of a fully-open Linux driver for it's latest generation of 11n chipsets. The driver, while still a work in progress, is released as full source and uses the native mac80211 stack. "
View 4 Replies
View Related
May 26, 2011
how to use my alpha awus036nh wireless adapter in bt3 that i am running from cd, whenever i try to scan for aps the built in adapter kicks in.
View 1 Replies
View Related
May 18, 2011
Yet another Linux newbie with wireless problems I'm afraid. I saw some postings that appear very similar but I don't have any Linux experience and don'h to make uncontrolled changes to the environment without expert advice.Background: I have an old laptop (HP Pavilion dv9000) with Vista installed and a troubled history (overheating motherboard failure), so I put it on the shelf and replaced it with a new Windows 7 laptop (Dell Studio 1555). But I have been intrigued by the Ubuntu reviews and thought I would dig out the old laptop and install Kubuntu 11.04 (replacing the 2 Vista partitions with a single Kubuntu partition).
Kubuntu installation was easy and I am impressed by the Kubuntu interface, but I soon noticed that it was not detecting my wireless router, which works fine for everything else (Dell, Sony Bravia TV and also an internet radio). The wired connection is okay (using it now) so I guessed the problem was Kubuntu notognising the Broadcom BCM4311.The network interface tool shows the wired connection but the Wireless tab is greyed out.I also installed Wicd Network Manager but that just confirmed what I knew.I noticed other threads have asked for the lspci and lsusb details so here they are:
lspci
00:00.0 RAM memory: nVidia Corporation C51 Host Bridge (rev a2)
00:00.1 RAM memory: nVidia Corporation C51 Memory Controller 0 (rev a2)
[code]...
View 4 Replies
View Related
Nov 3, 2010
How to configure Linux text console to automatically turn of the monitor after some time? And by "text console" I mean that thing that you get on ctrl+alt+F[1-6], which is what you get whenever X11 is not running. And, no, I'm not using any framebuffer console (it's a plain, good and old 80x25 text-mode). Many years ago, I was using Slackware Linux, and it used to boot up in text-mode. Then you would manually run startx after the login. Anyway, the main login "screen" was the plain text-mode console, and I remember that the monitor used to turn off (energy saving mode, indicated by a blinking LED) after some time. Now I'm using Gentoo, and I have a similar setup.
The machine boots up in text-mode, and only rarely I need to run startx. I say this because this is mostly my personal Linux server, and there is no need to keep X11 running all the time. (which means: I don't want to use GDM/KDM or any other graphical login screen). But now, in this Gentoo text-mode console, the screen goes black after a while, but the monitor does not enter any energy-saving mode (the LED is always lit). Yes, I've waited long enough to verify this. Thus, my question is: how can I configure my current system to behave like the old one? In other words, how to make the text console trigger energy-saving mode of the monitor?
View 1 Replies
View Related
