So I've tried some hours ago to install the new kernel 2.6.38 and when I did the reboot, it prompted this error: "Error 11: Unrecognize device strong
Press any key to continue..." I know this is such a general question but how to install the new kernel with Fedora 14? I think I did compiled and configured it ok and did something that wasn't recognized by grub or perhaps when I ran the command to make the new initrd.
I just installed say with
Code:
sudo apt-get install epos
and everything went fine, until I tried to use it.
When i do
Code:
say hello
it gives me
Quote:
he~lo######~T
Could not open localsound device, error 2 Client side error: Could not set up a stream
I am getting the same errors everytime I boot the server up:
Error: no such device {SOME-UUID}
Error: no suck disk
After that the system boots normally, but Im afraid ignoring this error can make my system crash in the future. I figured it was a grub error and I tried the update-grub2 command, it does detect all installed kernels no problem, but after I reboot I get the same error message.
I have a one problem when i mapped a SAN to the linux box RHEL 5.3 i show the following messeage Buffer IO error on Device /dev/sdband unable to find it in fdisk -l
View 2 Replies View RelatedI have installed Windows 7 followed by Fedora 11. Everytime I install Fedora 11 with Win 7, the first to boot, I get BOOTMGR missing. Later I used "df -h" command to see the disk file usage fdisk -l" to see the info regarding Disk Partitions. Went into the /boot/grub/menu.lst and modified the order. I set the partition where I find the bootmgr.exe.mui, there was another file named "memtest.exe.mui in the same file.
I navigated to the above said through Fedora 11. Located inside the Win 7 installed directory /boot/en-US/
When I changed the menu.lst file, I get a new error Error 12: Invalid device requested when I tried to boot Win 7. Does that mean that Fedora 11 GRUB is not getting the bootmgr.exe.mui since its 2 levels inside the boot directory ??
I tried to get 3d hardware support in my FC12 install. I grabbed the latest appropriate drivers from the nvidia website for my Geforce 6800 XT graphics card. I changed the inittab file to boot to command line, ran the .run file as root and ran into a couple errors doing so.
I then proceeded to use yum (which i do like but this is a bad scenario for me thus far) to update my drivers to the suggested kmod-nvidia drivers that exist out there. Once all of the installation was completed I rebooted and got the following error displayed at the top of my screen after the fedora loading bubble disappeared. The system just seems to hand at this point....
"usb 2-1: device descriptor read/64, error -62"
I did a hard boot on the machine and tried again, this time i pressed the esc key to watch the interactive startup screen and noticed that after "enabling local filesysem quotas: [ OK ]" i get a
***Warning -- SELinux targeted policy relabel is required.
*** Relabeling could take a very long time, depending on file
*** system size and speed of hard drives.
This will continue with asterisks across the screen until eventually it stops and then I am stuck as to what to do from here on out. What could possibly be causing all of this mayhem?I have tried to use the fedora core 12 install cd to launch it into "rescue mode" and from the bash command line proceed with modifying my grub.conf to not use the "newly installed kernel (2.6.32.11-99.fc12.i686)" that was installed with yum during my kmod-nvidia driver installation.
I have 2 hdds, with encrypted / and /home. Besides there are four other (encrypted ext4) partitions I use rarely. In Fedora 11 at boottime I gave the luks passphrase for / and home and the system booted as intended.
Whenever I needed those extra encrypted partitions I mounted them in Nautilus. Now, in Fedora 12 at boottime dracut tries to open all the encrypted partitions, / and /home are mounted fine, but opening all the other partitions gave the following messages in messages.log:
Quote:
dracut: luksOpen /dev/sdb6 luks-02a0e706-a26f-4019-a2a0-88a0366a994d
kernel: Buffer I/O error on device dm-0, logical block 124
kernel: device-mapper: ioctl: unable to remove open device temporary-cryptsetup-304
kernel: Buffer I/O error on device dm-0, logical block 124
kernel: Buffer I/O error on device dm-0, logical block 124
[code]....
...and these messages are repeated with the other partiitions, and the boot time takes very, very long. How can I tell dracut to ignore those extra encrypted partitions at boottime?
Since May 12,2009. Our system lifekeeper has the error log "lifekeeper error: DEVICE FAILURE on SCSI device '/dev/add'", but it ran normally. Until last week, it failover to the standby server. The disk still running, the error still come out.
View 3 Replies View RelatedCreate symlink /dev/root and then exit this to continue the boot sequence.
Buffer I/O error on device sr0, logical block *******
sr 4:0:0:0 [sr0] Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE,SUGGEST_OK
sr 4:0:0:0 [sr0] Sense Key : Medium Error [current]
sr 4:0:0:0 [sr0] ASC=0x10 <<vendor>> ASCQ=0x90
end_request: I/O error, dev sr0, sector 1395920
Clocksource tsc unstable (delta = -499902943 ns)
loops that during install. new hard drive fresh out of box. WD 320GB 7200 Toshiba Qosmio intell core duo i've installed with this same disk before previous hard drive died. installed over windows vista. this time im trying to install solo no windows disk to reinstall with, F10 only. I've tried other distros as well, Mandriva one 2009, Dreamlinux, and this one. i've suspected hard drive controller went out but i can format and partition the drive. also the cd/dvd drive is bad but im booting from cd fine. tried removing the cd drive and booting from an external usb cd rom, same errors.
im about to deploy and need my computer up and running ASAP. 7 months no entertainment is not good. when i use a linux boot disk from Ultimate Boot Disk (UBD) i get an error of - hda status no response and something about invalid heads dreamlinux pushes past the error till i get the error about cant start x server. about my graphics
I have recently installed Fedora11 and have managed to get the printer side of the above multifunction machine working but not the scanner . The computer recognises the scanner and sane, xsane, sanelib's etc are all installed . When I try to open it it gives the following:
Failed to open device 'brother3:bus5;dev1': Error during device I/O
i need to install vpnc in amazon ec2 fedor 8 instance. i have installed with yum install vpnc commaned. And i have placed config file in /etc/vpnc/some.conf. but it is not connecting and giving the following error.
vpnc: can't open /dev/net/tun, check that it is either device char 10 200 or (with DevFS) a symlink to ../misc/net/tun (not misc/net/tun): No such device.
So I cant seem to be able to install fedora 15. I think it is the disk. I have windows 7 already installed (and would like to keep it) It was installed on the end of the hard drive leaving a 100 GB chunk in the center of the drive open and unformatted (this may be the problem). Anyway I used the live cd and tried to format the unformatted partition to exf but it gives me this error
Code:
Error creating partition: helper exited with exit code 1: In part_add_partition: device_file=/dev/sda, start=105906176, size=104752742400, type=EBD0A0A2-B9E5-4433-87C0-68B6B72699C7
Entering MS-DOS parser (offset=0, size=500107862016)
MSDOS_MAGIC found
found partition type 0xee => protective MBR for GPT
Exiting MS-DOS parser
Entering EFI GPT parser
GPT magic found
partition_entry_lba=2
num_entries=128
size_of_entry=128
Leaving EFI GPT parser
EFI GPT partition table detected
containing partition table scheme = 3
got it
got disk
new partition
added partition start=105905664 size=512
committed to disk
Error doing BLKPG ioctl with BLKPG_ADD_PARTITION for partition 2 of size 105905664 at offset 512 on /dev/sda: Device or resource busy
Do I have to reinstall windows for this to work or is there something I can try to do.
Fedora
Release 12 (Constantine)
Kernel Linux 2.6.32.9-70.fc12.i1686
GNOME 2.28.2
[Code].....
OK so I installed Razertool but when I try to configure it, it says: There was an error communicating with the device: Operation not permitted You may need to change the permissions of the device (see the README)
and in the GUI it reads: FIrmware Version ?.?? (NO DEVICE) As for other things like CPU and Graphics, how can I confirm these are running properly? My computer seems to lag a bit. As for graphics, everytime I try to enable the desktop effects it errors and says: Accelerated 3D graphics is not available
I have a Feadora 12 Live CD. It booted up fine on my 700 Mhz computer. I've since then put a new HDD in with which I intended to install Fedora on. But now i get this message
Quote:
No root device found. Boot has failed, sleeping forever
What does this mean? How do get the Live CD to boot?
I have FC6 system with kernel 2.6.22.14-72.fc6 When I rebooted my system, I got error message "unable to access resume device (LABEL=SWAP-sda8) then it went to fsck automatically to all the partition and then stop (failed)
Checking filesystems
/1:clean, 10543/2560864 files, 204494/2560359 blocks
fsck.ext3: unable to resolve 'LABEL=/backup'
/boot: clean, 155076/19546112 files, 13456168/39072080 blocks
[Code]...
I tried to install OpenSuse 11.3 on my brand new pc, which already had Windows 7 proffessional in it, and I went step by step through the installation without changing anything. It didn't work. I tried for a second time and this error message kept popping up: "Creating device modes with udev 2.0436224] [drm: i915_diver_load]*ERROR*Detected broken BIOS with 262140/2644kb of video memory stolen. 2.0436224] [drm: i915_diver_load]*ERROR*Disabling GEM(try reducing stolen memory or updating the BIOS to fix)"
And then a lot of letters and numbers wich make no sense to me. Now the only way I can initiate OpenSuse is with the OSuse boot dvd and on failsafe mode.
Make: Fujitsu-Siemens
Model: LifeBook P7120
For some reason (hardware - I am guessing) the LiveCD does not boot on some laptops. The LiveCD worked well on my Dell Inspiron 1525 without any problems but my Fujitsu-Siemens refused to boot up. If you are trying to install or use F12 with the LiveCD ISO image burnt onto a CD on a laptop and fails with the following error:[drm:drm_mode_rmfb] *ERROR* tried to remove a fb that we didn't own Boot has failed, sleeping foreverthis workaround may work for you. Sometimes it will come up with another error about 'Root Device Not Found'
The workaround only works on a bootable USB key for some other reason, created with 'live-usb creator' and not a CD nor a LiveCD image on a USB created on a windows machine. I have tried them all.
[Code]...
i've just burned a livecd (fedora 11), but it doesn't work correctly.it says after i hit boot:
BUFFER I/O error on device sr0 logical block 352328
and then something else, which is similar so i didn't write it down.i read on bugzilla, that is should try to append the boot command with pci=nomsi, but it doesn't work for me
I just compiled my first own kernel (I'm using Arch Linux), following the tutorial on the german site. Now I tried to boot it, I ended up failing with this message: Code: Waiting 10 seconds for device /dev/sda1 ... Root device '/dev/sda1' doesn't exist, Attempting to create it. ERROR: Unable to determine major/minor number of root device '/dev/sda1' Here is the important part of my menu.lst:
[Code]....
I simply copy&pasted the Arch-entry, i.e. I also had the disk by uuid there. The failure message was the same, just the root device name was the different name Also, at first I did not have the initrd line in my menu.lst (as written in my tutorial that I may not need it). In this case I had this error message:
[Code]....
When I try to suspend to RAM my Fedora 12 system (2.6.31.12-174.2.22.fc12.x86_64), Screen goes blank for about 15 seconds, and then comes back as if nothing happened. I see the following error in /var/log/pm-suspend.log
[Code]....
I've got the F13 LiveCD that I was able to boot and use using the "nomodeset" boot option. From the desktop I'm trying to perform an Install to Hard Drive. I've read the Install from LiveCD post regarding the creation of a /boot partition and a / root partition. I've tried creating them without the LVM group and with. But every time I appempt to install I get...
An error occurred mounting device proc as /proc: mount failed: (9, None). This is a fatal error and the install cannot continue.
Hardware is a Sager 8887 (P4, 3.06HT, 60GB HDD, Radeon 9000 graphics adapter)
I've got the b43 driver and firmware installed, and the system comes up fine, but the max throughput on the wlan0 is about 100Kb/s. My laptop and iwl do about 2.5Mbps from the same location in the house. The signal is plenty strong:
wlan0
IEEE 802.11bg ESSID:"sar2"
Mode: Managed Frequency:2.422 GHz Access Point: 00:23:69:22:5C:00
Bit Rate=36 Mb/s Tx-Power=20 dBm
Retry min limit:7 RTS thr:off Fragment thr:off
Power Management:off
Link Quality=61/70 Signal level=-49 dBm Noise level=-57 dBm
Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0
Tx excessive retries:0 Invalid misc:0 Missed beacon:0
Is this expected from the b43 driver and a bcm4318? I was hoping for much better throughput. Also, I tried the broadcom-wl driver, but it doesn't seem to recognize the card. It looks like it's not supported from their site, only the 4311,12,21,22 were listed, although I see posts where other people claim they are using it with a 4318?
How should we install Samba printers in Fedora 15? The Gnome GUI fails. When trying through CUPS web interface, it spits out this error:Bad device-uri scheme "smb"!
EDIT: The default installation doesn't come with SAMBA installed.
Code:
yum install samba-client solved it for me. Maybe just "samba-common" also solves it.
when ever i give yum update am geting this error. failed to use search generator: failure:repodata/318b9912817ec3309c6defc47d79e878c52a21fd1457d191bb ff060fdb7f7f8d-primary.sqlite.bz2 from rpmfusion-free-updates: [Errno 256] No more mirrors to try. I was trying to install tomcat using yum. Is there any way i can install tomcat other than yum utility. I downloaded he zip folder for tomcat which i downloaded from apace tomcat site.
View 2 Replies View RelatedI have been trying to install MATLAB 2008b as a standalone version; however, every time when the process runs to 18% it shows an error as follows: "There was an error extracting the archives for MATLAB compiler. Chceck that you have enough disk space and rerun the installer."
I did have checked the disk space which is much more than enough. I have also changed few different disks that are way more than enough as well, about 5GB at least, but this error still popped out when it runs to 18%.
I tried to install Fedora 12 on my machine using the Fedora-12-i386-DVD and get the following error: /sbin/load_policy:error while loading shared libraries: lib/libsepol.so.1: cannot read the file data:input/output error exec of anaconda failed install exited abnormally [1/1]
View 2 Replies View RelatedI open an ODS file and edit it and save, fine. But sometimes and for no readily apparent reason it refuses to save the document with the error message:"Error saving the document <filename>: Write error. The file could not be written". I have upgraded my version of OpenOffice but the issue remains. Once it starts with that error the only way to save the file is to actually abandon my change and restart OOffice. Today I lost an hours stuff as the auto save was also failing but not giving me any warning it was failing. I'm not sure if this is an OpenOffice, file system, Fedora or permissions issue though I've not noticed anything similar with other applications. Have set permissions to 777 but still get the error.
View 3 Replies View Related[code]...
How do I fix this?
I am facing some strange problem of mysql replication with ssl, my replications which working fine from more than 6 months currently stopped working after i upgrade mysql in to newver version mysql-5.1.41-2, i create new ssl self singed certs but still no sucess, when client try to connect the master using ssl its gives error SSL connection error ERROR 2026 (HY000), with out ssl its working f9.
Platform --> Fedora-11 + mysql-5.1.41-2 (both master/client)
I can seeking the problem on net, and i found the below bugzilla url related to that.
[url]
I read it but not get , either new version support x509 ssl certs or not or either new version support ssl replication or not, here below my server configuration for ssl serts
And for client
Both server and clients certs are signed with same ca but still its currently not working after the mysql upgrade first 5.1.41 and then 5.1.41-2
Either as above bugzilla url, currently mysql support ssl replication or not, or either some need to do special for working with ssl. or i wait for newver version of mysql to fix if its bug or not.
I'm unable to change the setting of the actual printer on my system, cant even delete itthe system ask me the root password, after i enter it, i always get this message "There was an error during the CUPS operation:'client-error-not-authorized'."
View 8 Replies View Related