Fedora :: Usb 2-1: Device Descriptor Read/64, Error -62
Apr 23, 2010
I tried to get 3d hardware support in my FC12 install. I grabbed the latest appropriate drivers from the nvidia website for my Geforce 6800 XT graphics card. I changed the inittab file to boot to command line, ran the .run file as root and ran into a couple errors doing so.
I then proceeded to use yum (which i do like but this is a bad scenario for me thus far) to update my drivers to the suggested kmod-nvidia drivers that exist out there. Once all of the installation was completed I rebooted and got the following error displayed at the top of my screen after the fedora loading bubble disappeared. The system just seems to hand at this point....
"usb 2-1: device descriptor read/64, error -62"
I did a hard boot on the machine and tried again, this time i pressed the esc key to watch the interactive startup screen and noticed that after "enabling local filesysem quotas: [ OK ]" i get a
***Warning -- SELinux targeted policy relabel is required.
*** Relabeling could take a very long time, depending on file
*** system size and speed of hard drives.
This will continue with asterisks across the screen until eventually it stops and then I am stuck as to what to do from here on out. What could possibly be causing all of this mayhem?I have tried to use the fedora core 12 install cd to launch it into "rescue mode" and from the bash command line proceed with modifying my grub.conf to not use the "newly installed kernel (2.6.32.11-99.fc12.i686)" that was installed with yum during my kmod-nvidia driver installation.
View 1 Replies
ADVERTISEMENT
Feb 2, 2011
I'm having issues with getting my USB ports to work on my server. USB keyboards, mice, drives, flash drives, card readers, etc. will not work on this server.
dmesg
Linux version 2.6.18-194.32.1.el5 (mockbuild@builder10.centos.org) (gcc version 4.1.2 20080704 (Red Hat 4.1.2-48)) #1 SMP Wed Jan 5 17:53:09 EST 2011
BIOS-provided physical RAM map:
[code]...
View 4 Replies
View Related
Sep 3, 2010
While I had the case open to swap out a network card I thought I would drop in an old USB card (previously used with no problems on a machine running Debian) however on boot I'm now getting some errors showing up. The card has been sitting around for a while so it could be an issue with the card.
[Code]....
View 2 Replies
View Related
Aug 20, 2010
I'm designing an embedded USB device. When I connect the device to the computer, I get the following messages:
usb 1-3: device descriptor read/64, error 2
usb 1-3: device descriptor read/64, error 2
usb 1-3: device descriptor read/64, error 2
usb 1-3: device descriptor read/8, error -71
usb 1-3: device descriptor read/8, error -71
usb 1-3: device descriptor read/8, error -71
Note that other USB devices work fine. I am fairly certain that the problem is with my hardware. I'd like info on what these error messages mean to help my debug. Searching Google I wasn't able to find any explanations about what these errors mean exactly.
I'm running Cent OS 5.4 with kernel 2.6.18-164.el5 on an i686
View 1 Replies
View Related
Apr 3, 2010
I have been using CentOS 5. for around 3 months. It was all fine and was having a pleasant experience using CentOS. Today when i turned on my computer and booted CentOS i am having the below error: Grub comes up, allows me to select CentOS 5.4 kernel image. and displays RedHat Nash version: and then the below error occurs:
[Code]....
View 9 Replies
View Related
Jan 4, 2010
I recently updated eclipse 3.5.1.-27 I am getting the following error. No editor descriptor for id org.eclipse.jdt.ui.CompilationUnitEditor I am using sun jdk. I reinstalled it and tried to start. Same problem. When I try to open projects its not showing any java related things.
View 2 Replies
View Related
Mar 2, 2011
I have a recent install of ubuntu 10.10 on a brand new rig, and everything appears to be working properly but I get these 2 errors during bootup that seem to make the book process take a bit longer than expected but haven't actually noticed a problem in performance.
[6.394416] hub 3-1:1.0: config failed, can't read hub descriptor (err -22)
[6.752860] hub 3-2:1.0: config failed, can't read hub descriptor (err -22)
I have been unable to find a site with information on what err -22 means. From what little I have found on the issue it seems to be something with the usb 3.0 hubs on the back of my motherboard?
Code:
[0.864023] PCI: Using ACPI for IRQ routing
[0.864024] PCI: pci_cache_line_size set to 64 bytes
[0.864081] reserve RAM buffer: 000000000009dc00 - 000000000009ffff
[0.864082] reserve RAM buffer: 00000000df7e0000 - 00000000dfffffff
[0.864083] reserve RAM buffer: 000000021f800000 - 000000021fffffff
[0.864120] NetLabel: Initializing
[0.864121] NetLabel: domain hash size = 128
[0.864122] NetLabel: protocols = UNLABELED CIPSOv4
[0.864127] NetLabel: unlabeled traffic allowed by default ....
View 1 Replies
View Related
Apr 11, 2011
For the record, I'm having the same issue as the OP with Lucid with a backported 2.6.35-28 kernel and a Samsung scx-4623fw printer hooked up via USB. Same symptoms - lsusb hangs until the printer is unplugged, devices aren't recognized, etc. Dmesg output includes a bunch of device descriptor errors:
[603.091961] usb 7-1: new full speed USB device using ohci_hcd and address 9
[618.241335] usb 7-1: device descriptor read/64, error -110
[633.521986] usb 7-1: device descriptor read/64, error -110
I suddenly started having a bunch of USB issues (including complete system locks whenever I plugged in a logitech USB mic) around early march with the stock lucid kernel. Everything was fine before that.
View 4 Replies
View Related
Dec 20, 2010
I have an FC13 x86_64 server and having trouble building RPMs, but I don't think it's specifically an RPM problem. I think it's a tty management or other type of problem.
When spec files have a "%files -f filelist.txt", which contains the list of files for the RPM, it calls the /usr/lib/check-files script, which sorts the files that are supposed to be in the RPM and compares them with the files that are in the built RPM before they are packaged.
The trouble is that the sort fails.
Here's the trace from the check-files script:
The above doesn't show that the output from sort is redirected into those /tmp files. The first sort succeeds because it reads data sent by the "find" in the same shell. The second sort fails because (I think) it cannot read data from stdin for some reason.
What could possibly cause this? I've checked various permissions, libraries, even used strace extensively, all of which is inconclusive.
This is one of my test server boxes, so this problem is something that I've caused, but I have no idea what.
libc controls input and output, correct? Could it somehow be a glibc problem, or a devpts problem? I can run a simple command and pipe it to sort with no problem. It appears to only be related to sub-shells.
I also replaced sort with cat and just tried to redirect stdin in that file to a temporary file, and that also fails.
I've tried running it with selinux disabled and that has no effect.
View 7 Replies
View Related
Mar 25, 2010
I decided to take an old Gateway that I bought off a guy cheaply and turn it into a file and web server.I purchased copies of Debian 5.0.4 i386 disks (31 in all) on the advice of a friend, the disks weren't expensive, but now that Ive installed all the disks, I'm having a variety of errors
[443.110940 end request: I/O error, dev hde, sector 76021855
[443.111074] EXT3-fs error (device hde1): ext3_get_inode_loc: unable to read inode block - inode=2375715, block=9502724
INIT: cannot execute "/sbin/getty"
[Code]..
View 2 Replies
View Related
Apr 26, 2010
After a motherboard failure and replacement a Dell PE 6850, during the first restart, we receive this on running RHEL 4.5: Loading PBR for descriptor 3...done. Bad PBR Sig. Also, I have determined PBR to mean "Partition Boot Record." I have not been able to determine what "descriptor 3" is.
View 3 Replies
View Related
Mar 17, 2011
So I've tried some hours ago to install the new kernel 2.6.38 and when I did the reboot, it prompted this error: "Error 11: Unrecognize device strong
Press any key to continue..." I know this is such a general question but how to install the new kernel with Fedora 14? I think I did compiled and configured it ok and did something that wasn't recognized by grub or perhaps when I ran the command to make the new initrd.
View 6 Replies
View Related
Sep 14, 2009
error message when I ran my program that I couldn't open my local file. I have two files first one is called client, second one is called server I am using named pipes to sent a message from client to the other file called server in client I used mknod() to create the two named pipes,one for read,one for write and created new thread in client using fork() spawned a child process that executed the server file both named pipes are opened the client file got the message from the user and sent it through the named pipes to the server file when the server receives the message , it needs to verfify it is correct in the server file, a local file descriptor is created to read and send this verifing message when it is not correct but I am getting an OPEN() error when I tried to open this shared local array buff and attach it to a file descriptor where the message is kept why do I get this error in server file
int main()
{
/*both named pipes are open*/
rfd=open(IFIO1,0);
wfd=open(IFIO2,1);
[code]....
View 1 Replies
View Related
Feb 23, 2011
I tend to get constant crashes when using internet browsers ( Google Chrome and Firefox ) basically the application hangs not moving in any way, then eventually completely freezes up, the system then locks up and finally crashes.
Upon system re-start I get "Read Error" at boot ( No further information, it literally just says "Read Error" ).
It is sometimes fixed by going into the BIOS and select "Hold on No Error".
I tried installing OpenBios to see if using different BIOS firmware would resolve the issue, but the OpenBios install failed ....so no dice there either.
I am trying to work out if it is a hard drive problem or if it is purely a problem with Fedora.
It was working fine for a couple of months and when it does boot up ... the system works fine, ( Until another crash ).
It seems like the internet browsers crash the system and then the system crashes and can then no longer remember how to boot up.
what this could be that could be software based....if not it looks like I will need a new hard-drive.
View 5 Replies
View Related
Jul 20, 2010
I have a one problem when i mapped a SAN to the linux box RHEL 5.3 i show the following messeage Buffer IO error on Device /dev/sdband unable to find it in fdisk -l
View 2 Replies
View Related
Jan 20, 2010
This is weird, today I updated my system and while trying to visudo from single user mode got
"cannot read /etc/shadow: Permission denied"
which kept me from doing anything until I switched to file permissions of 400 on shadow, then back. Is this being experienced by anyone else or just me? /etc/security/limits.conf doesn't seem like it wants to change in enforcing mode either and I can't find any alerts to provide clues on the situation.
View 8 Replies
View Related
Apr 5, 2010
I'm playing with Fedora 12 and can't get GRUB to work. To boot, I've been using GRUB4DOS. While that works fine, I'd like to figure out what's wrong with regular GRUB 0.97. After the initial installation, GRUB came up on reboot, but it was broken -- it couldn't read the config file apparently, and no commands would work correctly. So I attempted to reinstall grub via the grub prompt. No matter what I do, or which hard disk I install GRUB on, I get "Error 18". I tried using the "grub-install" command as well as the prompt, and that did the same thing.
My system here is an ASUS M4A785TD-M EVO mo/bo. I've got four hard drives. Two 1TB SATA drives and a couple of PATA drives (300 and 500GB) on a Si608 controller card. Using the BIOS "BBS" boot menu, I can boot NTLDR and BOOTMGR off active partitions on any of the drives (with proper Boot.ini modifications to handle the change in drive order). GRUB4DOS works as well, and will boot Fedora 12 correctly off any of them (with proper menu.lst ministrations). But GRUB 0.97 that comes with Fedora just refuses to do anything other than say "Error 18".
View 4 Replies
View Related
Dec 4, 2009
I have installed Windows 7 followed by Fedora 11. Everytime I install Fedora 11 with Win 7, the first to boot, I get BOOTMGR missing. Later I used "df -h" command to see the disk file usage fdisk -l" to see the info regarding Disk Partitions. Went into the /boot/grub/menu.lst and modified the order. I set the partition where I find the bootmgr.exe.mui, there was another file named "memtest.exe.mui in the same file.
I navigated to the above said through Fedora 11. Located inside the Win 7 installed directory /boot/en-US/
When I changed the menu.lst file, I get a new error Error 12: Invalid device requested when I tried to boot Win 7. Does that mean that Fedora 11 GRUB is not getting the bootmgr.exe.mui since its 2 levels inside the boot directory ??
View 2 Replies
View Related
Apr 25, 2010
I switched back to Fedora after a long time and wow a lot of things have changed! Fedora 12 is looking amazing and the best part is I could install it on my USB so easily. And then I found I couldnt open any PDF files on Fedora - I tried installing AdobeReader, xpdf and openoffice. All of them are just throwing some file format errors.... <I cant push a screenshot now since i removed the packages>
Initally i thought it might be some version conflict but it turned out I couldnt open any pdf's including docs from 5 years back to docs with embedded media content. I know I havent put any info here. I am looking for a little info on what is needed to get Acrobat/Xpdf working in Fedora 12... And I couldn't get any errors logged so I'd like a little help there if I need to share some debug messages...
that gave these messages [root@localhost Presentations]# evince module-development.mgp.pdf
** (evince:5768): WARNING **: Failed to create dbus proxy for org.gnome.SettingsDaemon: Could not get owner of name 'org.gnome.SettingsDaemon': no such name
Error: May not be a PDF file (continuing anyway)
Error: PDF file is damaged - attempting to reconstruct xref table...
Error: Couldn't find trailer dictionary
Error: Couldn't read xref table
View 2 Replies
View Related
Sep 17, 2009
Since May 12,2009. Our system lifekeeper has the error log "lifekeeper error: DEVICE FAILURE on SCSI device '/dev/add'", but it ran normally. Until last week, it failover to the standby server. The disk still running, the error still come out.
View 3 Replies
View Related
Oct 5, 2009
i studied the program chardev.c from 'The kernel module programming guide'. The text tells me that by doing a :
1. 'cat' the character device is opened.
2. hi > /dev/hello the character device is written into.
now i wanted to know how to 'read' from the character device !
View 3 Replies
View Related
Nov 28, 2009
I have 2 hdds, with encrypted / and /home. Besides there are four other (encrypted ext4) partitions I use rarely. In Fedora 11 at boottime I gave the luks passphrase for / and home and the system booted as intended.
Whenever I needed those extra encrypted partitions I mounted them in Nautilus. Now, in Fedora 12 at boottime dracut tries to open all the encrypted partitions, / and /home are mounted fine, but opening all the other partitions gave the following messages in messages.log:
Quote:
dracut: luksOpen /dev/sdb6 luks-02a0e706-a26f-4019-a2a0-88a0366a994d
kernel: Buffer I/O error on device dm-0, logical block 124
kernel: device-mapper: ioctl: unable to remove open device temporary-cryptsetup-304
kernel: Buffer I/O error on device dm-0, logical block 124
kernel: Buffer I/O error on device dm-0, logical block 124
[code]....
...and these messages are repeated with the other partiitions, and the boot time takes very, very long. How can I tell dracut to ignore those extra encrypted partitions at boottime?
View 8 Replies
View Related
Apr 13, 2011
I need programmer a timer of 10 ms for read/write a USB device
View 4 Replies
View Related
Jan 29, 2009
Create symlink /dev/root and then exit this to continue the boot sequence.
Buffer I/O error on device sr0, logical block *******
sr 4:0:0:0 [sr0] Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE,SUGGEST_OK
sr 4:0:0:0 [sr0] Sense Key : Medium Error [current]
sr 4:0:0:0 [sr0] ASC=0x10 <<vendor>> ASCQ=0x90
end_request: I/O error, dev sr0, sector 1395920
Clocksource tsc unstable (delta = -499902943 ns)
loops that during install. new hard drive fresh out of box. WD 320GB 7200 Toshiba Qosmio intell core duo i've installed with this same disk before previous hard drive died. installed over windows vista. this time im trying to install solo no windows disk to reinstall with, F10 only. I've tried other distros as well, Mandriva one 2009, Dreamlinux, and this one. i've suspected hard drive controller went out but i can format and partition the drive. also the cd/dvd drive is bad but im booting from cd fine. tried removing the cd drive and booting from an external usb cd rom, same errors.
im about to deploy and need my computer up and running ASAP. 7 months no entertainment is not good. when i use a linux boot disk from Ultimate Boot Disk (UBD) i get an error of - hda status no response and something about invalid heads dreamlinux pushes past the error till i get the error about cant start x server. about my graphics
View 1 Replies
View Related
Sep 1, 2009
I have recently installed Fedora11 and have managed to get the printer side of the above multifunction machine working but not the scanner . The computer recognises the scanner and sane, xsane, sanelib's etc are all installed . When I try to open it it gives the following:
Failed to open device 'brother3:bus5;dev1': Error during device I/O
View 6 Replies
View Related
May 30, 2011
i need to install vpnc in amazon ec2 fedor 8 instance. i have installed with yum install vpnc commaned. And i have placed config file in /etc/vpnc/some.conf. but it is not connecting and giving the following error.
vpnc: can't open /dev/net/tun, check that it is either device char 10 200 or (with DevFS) a symlink to ../misc/net/tun (not misc/net/tun): No such device.
View 6 Replies
View Related
Jul 19, 2011
So I cant seem to be able to install fedora 15. I think it is the disk. I have windows 7 already installed (and would like to keep it) It was installed on the end of the hard drive leaving a 100 GB chunk in the center of the drive open and unformatted (this may be the problem). Anyway I used the live cd and tried to format the unformatted partition to exf but it gives me this error
Code:
Error creating partition: helper exited with exit code 1: In part_add_partition: device_file=/dev/sda, start=105906176, size=104752742400, type=EBD0A0A2-B9E5-4433-87C0-68B6B72699C7
Entering MS-DOS parser (offset=0, size=500107862016)
MSDOS_MAGIC found
found partition type 0xee => protective MBR for GPT
Exiting MS-DOS parser
Entering EFI GPT parser
GPT magic found
partition_entry_lba=2
num_entries=128
size_of_entry=128
Leaving EFI GPT parser
EFI GPT partition table detected
containing partition table scheme = 3
got it
got disk
new partition
added partition start=105905664 size=512
committed to disk
Error doing BLKPG ioctl with BLKPG_ADD_PARTITION for partition 2 of size 105905664 at offset 512 on /dev/sda: Device or resource busy
Do I have to reinstall windows for this to work or is there something I can try to do.
View 2 Replies
View Related
Dec 18, 2010
I am trying to add/delete files from my HTC Evo through ubuntu via enabling file sharing on the device. Ubuntu detects the drive, and mounts it up so that I can browse/read files off the device. However, I am not able to do any writing to the device because it is mounted as "read-only". The only wierd thing is that it worked last week, and I have not changed any settings on my system. Where should I start? Is the auto-mount for USB drives located in "/etc/fstab"? because here is the contents of that file, and I dont see anything for usb mounts:
Code:
# /etc/fstab: static file system information.
#
# Use 'blkid -o value -s UUID' to print the universally unique identifier
# for a device; this may be used with UUID= as a more robust way to name
[Code]....
View 1 Replies
View Related
Aug 13, 2009
I'm playing a little bit with OpenCV but the webcam that i have on my desktop isn't app-friendly... so i could not get it working with OpenCV, it's a 0ac8:301b Z-Star Microelectronics Corp. ZC0301 WebCam and it worked out of the box with Cheese and after a little bit of tweak i get it working with camorama also.But some apps, like Skype and OpenCV demos doesn't work, believe me, i tried everything to get it working, i tried even upgrading to a very new kernel.
So i had the idea to create a "virtual" video device and using some app that can read the wcam i could print the wcam's output on such device, which should be compatible and app-friendly, so i would use that device always.
View 1 Replies
View Related
Mar 4, 2011
I need to change a filename but when I boot up I get the message root device is read-only. Is there a way of changing this so that I can change the filename. I have a Mac Pro running Leopard OSX. The graphics card an NVIDIA 7500GT or driver has failed. It was suggested elsewhere that I change the relevant kext files to filename.kext.old, which I did, now when I try to boot start in OSX I get a message in various languages telling me to restart. I have tried booting in safe mode and from original Installation CD. In Safe Mode I get the same multi language splash screen, from CD I still have the graphic card problem, screen freezes and artifacts appear. So I boot up straight into CLI by holding down CMD-S hoping to be able to change filenames back but it says device read-only.
View 2 Replies
View Related
