Fedora Installation :: Error Creating Partition - Device Or Resource Busy

Jul 19, 2011

So I cant seem to be able to install fedora 15. I think it is the disk. I have windows 7 already installed (and would like to keep it) It was installed on the end of the hard drive leaving a 100 GB chunk in the center of the drive open and unformatted (this may be the problem). Anyway I used the live cd and tried to format the unformatted partition to exf but it gives me this error

Code:
Error creating partition: helper exited with exit code 1: In part_add_partition: device_file=/dev/sda, start=105906176, size=104752742400, type=EBD0A0A2-B9E5-4433-87C0-68B6B72699C7
Entering MS-DOS parser (offset=0, size=500107862016)
MSDOS_MAGIC found
found partition type 0xee => protective MBR for GPT
Exiting MS-DOS parser
Entering EFI GPT parser
GPT magic found
partition_entry_lba=2
num_entries=128
size_of_entry=128
Leaving EFI GPT parser
EFI GPT partition table detected
containing partition table scheme = 3
got it
got disk
new partition
added partition start=105905664 size=512
committed to disk
Error doing BLKPG ioctl with BLKPG_ADD_PARTITION for partition 2 of size 105905664 at offset 512 on /dev/sda: Device or resource busy

Do I have to reinstall windows for this to work or is there something I can try to do.

View 2 Replies


ADVERTISEMENT

Ubuntu Installation :: Cannot Create Partition: Device Or Resource Busy

May 11, 2010

When installing I am selecting the manual partitioning scheme( I have arch on another partition). After I have selected my custom partitions and their mount points it starts the installation but almost immediately it gives the error message that it cannot create a partition on the specified one, as it is used by the OS. I have also tried to create partitions through gparted in the live session but to no avail. I am sure that no partitions are mounted or in use by the system, I have checked this using the mount and fuser commands. I also tried the oem installation but the result the same.

View 3 Replies View Related

Fedora :: Error "Device Or Resource Busy" When Trying To Suspend RAM

Mar 1, 2010

When I try to suspend to RAM my Fedora 12 system (2.6.31.12-174.2.22.fc12.x86_64), Screen goes blank for about 15 seconds, and then comes back as if nothing happened. I see the following error in /var/log/pm-suspend.log

[Code]....

View 2 Replies View Related

Fedora :: XFS Mount Failed - Device Or Resource Busy

Sep 8, 2011

After upgrading to fedora 15, I have problems mounting XFS filesystem.

The short tale:
Code:
08:01:38 localhost root>mount -t xfs -vv /dev/sdb1 /data/disks/old
mount: /dev/sdb1 already mounted or /data/disks/old busy
08:01:39 localhost root>fuser /data/disks/old
08:01:41 localhost root>lsof /data/disks/old
08:01:44 localhost root>xfs_repair -t 1 /dev/sdb1
xfs_repair: cannot open /dev/sdb1: Device or resource busy
08:01:48 localhost root>fuser -mu /dev/sdb1
08:02:08 localhost root>dmesg | tail -n 5
[1655779.759764] SGI XFS Quota Management subsystem
[1659275.905756] SGI XFS with ACLs, security attributes, large block/inode numbers, no debug enabled
[1659275.908745] SGI XFS Quota Management subsystem
[1659389.154986] SGI XFS with ACLs, security attributes, large block/inode numbers, no debug enabled
[1659389.156519] SGI XFS Quota Management subsystem

Device is not mounted, and directory is not in use, it has just been created. There is nothing in log files that could remotely point the cause. After removing device (echo 1 > /sys/block/sdb/device/delete) and reattaching it, disk started working.

View 2 Replies View Related

OpenSUSE Hardware :: Mounting Encrypted Fs Error : Remove Ioctl Failed: Device Or Resource Busy

Dec 5, 2010

The error message I keep getting during mounting is:-

device-mapper: remove ioctl failed: Device or resource busy

This is from ane external USB HDD I use as a backup device. I've tried formatting it as ext4 ane encrypting it from the command line

# mkfs.ext4 /dev/sdc1
# cryptestup luksFormat /dev/sdc1

which run without errors but an attempt to mount throws up the above error as well as saying - you must specify the file type (tried that) - and fails to mount. I've tried using YaST to format and encrypt it which throws up the same error when I run mount but actually does actually mount the filesystem Googling around has brought up info saying that it's probably a race condition brought on by invalid udev rules. I've got a (mostly) working system and the udev rules documentation leaves more confused than when I started.

View 8 Replies View Related

Debian Installation :: Mount Root Filesystem Failed: Device Or Resource Busy

Jun 16, 2010

I've upgraded my squeeze box to linux kernel 2.6.32-5. But it shows mounting "here is the uuid of / " on /root failed: Device or resource busy while booting.Here is the menuentry of linux kernel 2.6.32-5.

[code]....

View 9 Replies View Related

Ubuntu Multimedia :: Unable To Open Device /dev/dsp - Device Or Resource Busy

Apr 13, 2010

All my music editing software programs say, "unable to open device /dev/dsp.Device or resource busy." How can I fix this?

View 3 Replies View Related

Ubuntu :: Mdadm: Cannot Open Device /dev/sdb1: Device Or Resource Busy

Jun 11, 2011

I rebooted my server and out of nowhere the RAID5 array won't assemble. I've tried everything I could think of to reassemble the thing. I fear that the array is ruined, but I can't imagine how. Here are various bits of information: The simplest failure (with and without partition numbers, which have not been needed in the past):

Code:

richard@nas:~$ sudo mdadm --assemble --verbose /dev/md0 /dev/sd[bcd]
mdadm: looking for devices for /dev/md0
mdadm: cannot open device /dev/sdb: Device or resource busy

[code]...

View 5 Replies View Related

Server :: CIFS Mounted Multiple Times / Error "Device Or Resource Busy"?

Feb 10, 2011

I have a little problem with my RHEL5.5 IA64. I mounted a Windows directory with 'mount -t cifs'. After a little while someone else mounted the same windows directory in the same mountpoint. The output from 'mount -v' shows me that the same directory is mounted twice in the same mountpoints. I cannot unmount it, not even with the force option. The error is "Device or resource busy". There are no open files in the shared directory and no one using the directory or subdirectories.

View 6 Replies View Related

Hardware :: Device Or Resource Busy ?

Jan 16, 2010

I am trying to set up a mdadm raid in a new machine that I am building as a home theatre PC. the machine boot just fine from /dev/sdc running ubuntu 9.10 However in gparted /dev/sda and dev/sdb show to be part of /devmapper/sil_ajbicfacbaej

Both dev/sda and /dev/sdb were drives that used to be part of a sil hardware raid on a previous machine. I would like to use them as a new mdadm raid on this new machine the old hardware card was really quite slow. the drives are now pluged into the MB and should be much faster there.

fdisk -l shows this

It produces no errors but does not remove it.

View 1 Replies View Related

Ubuntu :: Fsck On Busy Device Or Resource

Apr 4, 2011

I am dual-booting my Gateway laptop with Windows XP Media center Ed. and Ubuntu Notebook 10.10. Several weeks ago I was in the midst of downloading a program from the software center and my system starts running slow (this is in the Ubuntu kernel, not the Windows OS). So I decided to cold-boot the laptop in mid-download. When it boots back up, I get dropped to a grub-rescue menu that states the following:

Code:

Now, the only way I can even remotely use my laptop at the moment is to use my Live USB with the corresponding version of Ubuntu Netbook 10.10 or the Live CD I made with Ubuntu 10.04 on it (I'll explain why I made this below).

I read somewhere that I need to run fsck on my device to try to fix the partition, which btw my Ubuntu partition on my device is /dev/sda5, and before someone suggests it, I even tried using GParted and it doesn't work.

The reason I made a 10.04 CD is because I read somewhere that using the fsck from 10.04 might be more effective (for whatever reason) than the 10.10 fsck version.

I'd also like to add that I'm incapable of booting onto my Windows OS at all, yet I can access the partition from my Live CD/USB. the Ubuntu partition however, I can neither access or mount.

I tried running fsck on the entire device partition table, and I get the following:

Code:

This is me running fsck from the 10.04 version, I get a similar msg from the 10.10 Live USB but replace fsck.ext2 with fsck.ext4 in the message.

View 9 Replies View Related

Ubuntu :: E2fsck Fails Device Or Resource Busy

Mar 3, 2011

My son's netbook with 10.10 netbook remix failed to boot. Using the Live install CD and Gparted I couldn't repair the EXT4 filesytem. The error reported was:

e2fsck : Device or resource busy while trying to open ...

After trying many solutions and web searching I decided to try a different live CD and tried Knoppix 6.4.4

Using the command interface I typed e2fsck -v -f -y /dev/xxxx (xxxx = your device). This worked first time and the machine rebooted without hesitation.

View 1 Replies View Related

Debian Multimedia :: Alsa Just Returns With Device Or Resource Busy

Mar 31, 2015

Using debian testing.

Pulseaudio got installed by default here during installtion. Since I don't want it I first ran "systemctl disable pulseaudio", "pulseaudio --kill", then without rebooting I use mpd with alsa alone and it worked fine.

But then i rebooted, and now all applications, mpd, mpv, chromium etc just says that alsa returns with "Device or resource busy", tried rebooting again with no effect.

The soundcard appears as card 1 according to the output of "aplay -l", and defined that card 1is suposed to be default with this in "/etc/asound.conf":

Code: Select allpcm.!default {
    type hw
    card 1
}

ctl.!default {
    type hw
    card 1
}

It occurred to me that there might be an issue with permissions to the soundcard so I ran "ls -l /dev/snd"

Code: Select alldrwxr-xr-x  2 root root       80 Mar 31 03:27 by-path
crw-rw----+ 1 root audio 116,  8 Mar 31 03:27 controlC0
crw-rw----+ 1 root audio 116,  2 Mar 31 03:27 controlC1
crw-rw----+ 1 root audio 116, 12 Mar 31 03:27 hwC0D0
crw-rw----+ 1 root audio 116,  7 Mar 31 03:27 hwC1D0

[Code] ....

My user is a part of the audio group:

Code: Select alluid=1000(roberth) gid=1000(roberth) groups=1000(roberth),24(cdrom),25(floppy),29(audio),30(dip),44(video),46(plugdev),108(netdev),111(scanner)

As far as I can tell, that looks fine unless I am missing something?

View 1 Replies View Related

CentOS 5 :: Mdadm: Cannot Open /dev/sda2: Device Or Resource Busy

Dec 5, 2010

Trying to complete a RAID 1 mirror on a running system and have run into a wall at the last part. I can't add the active physical disk to the mirror. This is on a Centos 5.6 x86_64 system. Anybody know where to go from here? I've tried adding the nodmraid line to the kernel boot line with no luck. Tried removing the logical volumes from LVM, but it won't let me. Not a Linux newbie, but haven't set up a RAID in a long time.

[root@blackbox-0-2-e3-23-72-c5 ~]# mdadm /dev/md1 --add /dev/sda2
mdadm: Cannot open /dev/sda2: Device or resource busy

Here's output from fdisk -l:

[root@blackbox-0-2-e3-23-72-c5 ~]# fdisk -l
Disk /dev/sda: 320.0 GB, 320072933376 bytes
255 heads, 63 sectors/track, 38913 cylinders

[code]....

Here's mdadm.conf:

[root@blackbox-0-2-e3-23-72-c5 ~]# cat /etc/mdadm.conf
ARRAY /dev/md0 level=raid1 num-devices=2 UUID=3c6f7354:b9bfc86a:aa9d0dfb:cdd51bd8
ARRAY /dev/md1 level=raid1 num-devices=2 UUID=31ee55ba:be3b3606:974ac87d:627435a9

View 9 Replies View Related

Ubuntu Servers :: RAID5 Failed - MDADM (Device Or Resource Busy)

Feb 2, 2010

Something weird happened last night and my raid5 failed. I am trying to re activate it and see if my data is dead or what. When I run mdadm -Asv /dev/md0 I get

Code:
mdadm: looking for devices for /dev/md0
mdadm: cannot open device /dev/dm-1: Device or resource busy
mdadm: /dev/dm-1 has wrong uuid.
mdadm: cannot open device /dev/dm-0: Device or resource busy
mdadm: /dev/dm-0 has wrong uuid.
mdadm: cannot open device /dev/sde2: Device or resource busy
mdadm: /dev/sde2 has wrong uuid.
mdadm: cannot open device /dev/sde1: Device or resource busy
mdadm: /dev/sde1 has wrong uuid.
mdadm: cannot open device /dev/sde: Device or resource busy
mdadm: /dev/sde has wrong uuid.
mdadm: cannot open device /dev/sdd: Device or resource busy
mdadm: /dev/sdd has wrong uuid.
mdadm: cannot open device /dev/sdc: Device or resource busy
mdadm: /dev/sdc has wrong uuid.
mdadm: cannot open device /dev/sdb: Device or resource busy
mdadm: /dev/sdb has wrong uuid.
mdadm: cannot open device /dev/sda: Device or resource busy
mdadm: /dev/sda has wrong uuid.

View 4 Replies View Related

Ubuntu :: Mdadm Device Or Resource Busy Using Drives From Old Hardware Raid?

Jan 16, 2010

I am trying to set up a mdadm raid in a new PC that I am building for home theatre. the machine boot just fine from /dev/sdc running ubuntu 9.10 However in gparted /dev/sda and dev/sdb show to be part of /devmapper/sil_ajbicfacbaej Both dev/sda and /dev/sdb were drives that used to be part of a sil hardware raid on a previous machine. I would like to use them as a new mdadm raid on this new machine the old hardware card was really quite slow. the drives are now pluged into the MB and should bw much faster there.

fdisk -l shows this
*********************************************** ~$ sudo fdisk -l
Disk /dev/sda: 1500.3 GB, 1500301910016 bytes
255 heads, 63 sectors/track, 182401 cylinders

[code]....

View 6 Replies View Related

Ubuntu :: Fatsort - Sort_fs: Device Or Resource Busy - Cannot Read Boot Sector Or Headers

Feb 14, 2011

I have an audio recorder that doubles as a music player. It can play WAV files. So I put in some WAV files and they are out of order, even if they are named numerically. Read somewhere about a little CLI software called fatsort so I installed. The device is located at /dev/sdc. So naturally I write fatsort /dev/sdc, it says something about permission. So sudo fatsort /dev/sdc. Thing is, it says:

Code: sort_fs: Device or resource busy! If I "eject" it (unmount) then it says something about cannot read boot sector or headers. On Windows there is FAT Sorter. It does not work in WINE. So every time I put something in, I have to get to a Windows computer to sort it. It seems like fatsort is the only program that sorts FAT systems in Ubuntu/Linux.

View 1 Replies View Related

Ubuntu :: Claim Interfaced Failed: Could Not Claim Interface 0: Device Or Resource Busy

Apr 10, 2011

I'm currently running Ubuntu Maverick - 2.6.32-30-generic. I recently bought a Garmin eTrex Vista H, which connects via usb (from my reading, it looks like older versions connected over serial). Well, like so many before me, I can't seem to write to or read from the device via gpsbabel.Originally tried to read anything from the device (I have one waypoint in there) via:

Code:

gpsbabel -i garmin -f usb:

It returned "Found no Garmin USB devices." I then tried turning on the eTrex. Doing the same while locating satellites just does nothing - I have to escape from the command in terminal. Trying again produces the error:

Quote:

Claim interfaced failed: could not claim interface 0: Device or resource busy

After doing some research, I unblacklisted and then reblacklisted garmin_gps. I also went into

Code:

/etc/udev/rules.d/51-garmin.rules

to verify that the contents were:

Quote:

SYSFS{idVendor}=="091e", SYSFS{idProduct}=="0003", MODE="666"

as directed in this . Everything seemed to be correct.I then followed some other advice found here and created the policy under /etc/hal/... Still no luck!

View 5 Replies View Related

Debian :: Debian 5 Mdadm "device Or Resource Busy" Raid?

Dec 26, 2010

I installed mdadm fine and all and proceeded to run:mdadm --create --verbose /dev/md0 --level=stripe --raid-devices=2 /dev/sda /dev/sdbWith sda being my primary hard drive, and sdb being the secondary.I get this error message upon running the command"mdadm: chunk size defaults to 64Kmdadm: Cannot open /dev/sda: Device or resource busymdadm: create aborted"I don't know what's wrong!

mdstat says:
"Personalities : [linear] [raid0] [raid1] [raid10] [raid6] [raid5] [raid4] [multipath] [faulty]
unused devices: <none>"

View 1 Replies View Related

Fedora :: Cannot Unmount Because Device Is Busy

Feb 26, 2011

Code:
HP 210 Mini
Fedora 14 xfce
2.6.35.11-83.fc14.x86_64

I have inserted my handy drive. However, when I right click and select unmount I get the following message:

Code:
An application is preventing the volume "New Volume" from being unmounted

So I try from the command line:

Code:
umount /dev/sdb1
And I get the following message:

Code:
umount: /media/New Volume: device is busy. All I have done is copied some files to my handy drive. So I am not sure what process is keeping my handy drive busy.

Is there any command that I can use to see what process of anything else is using the handy drive?

View 3 Replies View Related

Fedora Installation :: Installation - Creating A Swap Partition Or A Boot Partition?

Jul 27, 2009

I have a brand new thinkpad X301 with 4GB of RAM and thinking of getting fedora 11 on it. The plan is to have it triple boot with vista/seven and hopefully OSx86. I am aware of the 4 primary partitions limit on an MBR disk. I was thinking of having a swap file instead of swap partition and not creating a boot partition as well. If I install the boot loader(GRUB?) on the root partition will I be able to boot it without any problems by using vista's boot loader?

Or Maybe I should install GRUB on the MBR and add all the other operating systems on it? Does anyone have any objections for not creating a swap partition or a boot partition? When comes to desktop environment I've been using KDE in the past, is there any major advantage of using Gnome over it? KDE seems to look really nice on fedora where Gnome is maybe more stable?

View 4 Replies View Related

Ubuntu :: External Hard Drives - Error "Cannot Unmount Because File System On Device Is Busy"

May 19, 2011

Having problems with external hard drives. I may be wrong, but I suspect they originated with an upgrade to 10.04 last Christmas. Around that time I also started using Amazon's S3 storage system, and, as a consequence, I stopped using my WD 80G external drive, previously used to backup my important files.

A week or so ago I decided to start using the WD drive again. I can't remember exactly what I did, but it wasn't happy - never caused any problems before. When I plug it in, the on-off light as the front keeps flashing on and off, and when I try to remove the drive I get the message: Error unmounting volumne An error occured while performing an operation on "My Book" (Partition 1 of WD 800BB External): The device is busy

Details: Cannot unmount because file system on device is busy Assuming the device had died - it's about 5 years old - I bought a 160G Samsung S-Series drive - my but they do look neat! Unfortunately, this doesn't seem to have solved my problem. I plugged the new drive in, and it happily appeared on my desktop. It seemed a good idea at the time, but I then started to format the drive - using the default option of FAT. All went well at first, but then the format process stopped.

My new Samsung drive now seems to be operating pretty much as the WD device, I can't copy to the drive, and attempts to unmount it generate a response similar to what's happening with the WD drive. Currently, although plugged in, I can't see the drive on my desktop, although it appears under Places. However, when I try to mount the drive, I get the message: Unable to mount SAMSUNG A job is pending on /dev/sdb1

View 1 Replies View Related

Ubuntu Installation :: Error While Installing, Retval=1, Device Partition=H?

Jul 7, 2011

I have a HP Pavilion dm4-1177 (640GB HDD, 6GB RAM, Windows 7 Home Premium 64 bit os, Intel core i5 2,4GHz).I tried to install Ubuntu 11.04 (both 32 bit and 64 bit) using the wubi, on a separate partition I keptexclusively for linux (10GB). During the mid-way of installation, it said:

An error ocurred:
Error executing command
>>command=C:Windowssysnativecdedit.exe/set{c644fa11-0e.......................} device partition=H:

[code]....

View 5 Replies View Related

Ubuntu Installation :: Locked Out Of Windows Partition With Grub - Error: No Such Device: 2e3857fb3857c08f

Apr 5, 2011

I have two partitions on my HDD. A Windows XP (hd0,2) and an Ubuntu 9.10 (hd0,1).I have been using the Windows mainly and ran a program that changes the HDD's serial number. Now when I boot up and Grub loads, I try to access the Windows partition and get the following error:

Error: No Such Device: 2e3857fb3857c08f

I am still able to boot the Ubuntu partition but can not seem to get grub to point to the Windows partition any more. This is very frustrating as I really need to get back into that partition soon.

View 9 Replies View Related

Fedora Installation :: Shrinking A Ntfs Partition - Free Up Space In Creating Custom Layout?

Nov 22, 2010

Im trying to shrink a 80 Gb ntfs partition. but when i clicked the shrink option the partition is like this:

"sda1(ntfs,0 mb)".

how to free up space in creating custom layout.

View 1 Replies View Related

Ubuntu Networking :: Error While Creating Wireless Network - Set Failed On Device?

Jan 16, 2010

I have been working on this for a while now and am absolutely stumped. Basically, what i am attempting to do is make my ubuntu box into a gateway for my network. I have everything working thru hard wire, but I simply cant get the wireless to work. No matter what I do, I cannot get my wireless card to transmit an essid and allow nodes to connect. I have tried assigning it in the interfaces file (shown below), and I have also tried manually modifying it using the iwconfig command. Here is the topology:

eth1: internet WAN
eth2: ethernet out to LAN
ra0: wireless out to LAN
Here is a copy of my /etc/network/interfaces file:
[CODE]
auto lo

[Code]...

View 2 Replies View Related

Ubuntu Installation :: Device Busy Using Image Scan - Reports Could Not Send Command To Scanner Check The Scanner Status

Apr 9, 2010

Have Karmic 9.10 ,Changed from Epson RX595 all in 1 (uses a ton of ink)Got the Lexmark Pro 805 3 in 1 because it says it supports Linux and the ink cartridge only cost $5 downloaded drivers and printer works but using Xsane Image Scanner error reports

'Lexmark_1_0_0:libsub/001/009': Device busy Using Image Scan - reports Could not send command to scanner Check the scanner status. The RX595's scanner drivers had to been manually instatlled,, in the Printer box the Lexmark shows available..

View 3 Replies View Related

Ubuntu :: Error While Creating A New Partition?

Dec 28, 2010

I'm trying to install XP Sp 3 on my comp which is running Ubuntu atm. But when I tried to create a partition after I clicked "Apply" I get this error :

GParted 0.6.2 Libparted 2.3 Create Primary Partition #1 (ntfs, 74.50 GiB) on /dev/sda 00:00:01( ERROR ) create empty partition 00:00:01( ERROR )libparted messages( INFO ) Partition(s) 1, 5 on /dev/sda have been written, but we have been unable to inform the kernel of the change, probably because it/they are in use. As a result, the old partition(s) will remain in use. You should reboot now before making further changes.

View 2 Replies View Related

Ubuntu :: Device Is Busy - Can't Format

Feb 17, 2011

I have a 250gb External HD and wanted to format it using the disk utility but every time I try Ubuntu tells me that the drive is busy.

How is it busy? I have nothing opened and haven't used it in anyway other than plugging it in. It doesn't even tell me what's using it.

View 4 Replies View Related

Ubuntu Installation :: Dual Boot - "error: No Such Device" After Reformatting/reloaded XP Partition

Feb 12, 2010

XP and Ubuntu are on different drives and they were booting ok prior the the reformatting. With the Ubuntu drive selected as the 1st hd boot device in Bios: I can boot into Ubuntu ok if I select it in the Grub2 menu If I select XP in the Grub menu I get:

"error:no such device c8e4918ce4917cfe"

If I select the XP drive as the 1st hd boot device in Bios I can boot straight into XP.So that is ok. This thread: [URL] has given me a clue that: "The UUID listed in grub.cfg is wrong In some cases the UUID in the above search line in grub.cfg is wrong. This can for example happen if the UUID has changed due to formatting or partitioning. Bugs The "search" function is plagued by various bugs (see [1], [2]), causing the search to fail."

However the fix in that thread gives me this result: "At the grub menu at boot up (you might have to hold the "shift" key or press "Esc" to get to the Grub menu) select the OS you are trying to boot. But do not press "enter", press "e" instead to edit the menuentry. Delete the line

search --no-floppy --fs-uuid --set 86d32ee3-aec6-490b-8dab-e5cfff9c7af9

and then press "Ctrl+X". This should boot your OS. If you were not able to boot into you OS, you are infected by a different problem and should not continue this howto." My Boot info script results are:

Code:

============================= Boot Info Summary: ==============================
=> Windows is installed in the MBR of /dev/sda
=> Grub 2 is installed in the MBR of /dev/sdb and looks on the same drive in

[code]....

View 9 Replies View Related







Copyrights 2005-15 www.BigResource.com, All rights reserved