got a new MoBo today. dropped it in and powered it up to find no network connection. when I dig though network manager I find no network devices, same with "network configuration" lspci gives:
03:00.0 Ethernet contoller [0200]: Atheros Communication Device [1969:1083] (rev c0)
ifconfig gives just the "lo" device. is there a hardware detection step I'm missing? I should mention this is a swap of one onboard NIC for another.
Cannot activate network device eth0!"device eth0 does not seem to be present, delaying initialization".i cannot find my network card while i set up network configuration Now I use dual boot window 7 and fedora 9,I cannot find my network card in select network adapter while network configuration ,i have a network card Atheros AR8132 PCI-E fast Ethernet controller NDIS(620)and for wired in Accer laptop .
View 1 Replies View RelatedI have been running F13 since it came out, with the wireless working fine since I got it working (using the RPM Fusion repository, broadcom-wl-5.60.48.36-1.fc13). Since I updated software (without reading what was to be updated), yesterday, I am unable to even find wireless networks, although I am, as you can see, able to access through eth0 It is not a hardware problem, as I can not only find them, but access them on Ubuntu 9.10 live disc. Below is my lspci
00:00.0 Host bridge: Intel Corporation Mobile 4 Series Chipset Memory Controller Hub (rev 07)
00:02.0 VGA compatible controller: Intel Corporation Mobile 4 Series Chipset Integrated Graphics Controller (rev 07)
00:02.1 Display controller: Intel Corporation Mobile 4 Series Chipset Integrated Graphics Controller (rev 07)
[code].....
I just want know, how two network card in one PC working on fedora. I want try setup router + firewall on my PC. And i need tutorial how is working
View 1 Replies View RelatedI have Lucent Technologies Orinoco Silver 11 Mbps PCMCIA wifi card. It worked perfectly in Fedora 10, but after updating to Fedora 11 it stopped finding any wireless networks. The updating were done with automatic updating utility. The card works perfectly in Windows, I tested it today.
My laptop is HP nx6110 if that matters.
Here is the situation:
When I plug-out the card, the Network Manager disables wireless networking as it should. When I plug-in the card, wireless networking is enabled, so the system seems to recognize the card in some way.
If I try to connect to "Hidden wireless network" (because there isn't any wireless networks listed in the Network Manager) system tries to connect for a couple of minutes, and then asks wireless settings again. Orinoco card's lights DOESN'T blink normally when connecting to the network (one light should blink rapidly and one should light continuously, but both are blinking rarely or doesn't blink at all).
In System->Administration->Network in tab Hardware (hope those names are correct, I use Finnish version of Fedora...) is:
It seems that the card is detected right.
Here is what I have done to get the problem solved: In System->Administration->Network I have tried to connect to the wireless network manually (disabling the Network Manager). I can't get the connection. It gives me random error messages, sometimes "Check the cable" or something like that, sometimes just timeouts IP determination.
I have tried to connect different wireless networks, no connection. All tested networks worked with another computer.
No matter if I reboot or service network restart or plug-out plug-in the card... the problem still appears.
Tried to find (and reinstall) drivers:
Code:
No Matches found
Code:
Here is the output of lspci. The output is the same if the wifi card is connected or not.
Code:
LAN connection is working just fine.
I am recently trying to get a steady wireless connection running. I am currently using the default settings/driver Fedora 13 is stocked with. As my internet browsing is somewhat up and down in load times, I decided to check in a video game which is generally a good test for me. haha I am harshly spiking and cannot find the source of my problem so my guess is a driver issue.
lspci | grep Network:
Code:
Code:
It is is seemingly right, my Windows 7 harddrive works just fine, this is just one last of the few issues I'm having from fully formatting my winblows HD to use as Linux storage.
I cannot find any native AR5008 Linux Drivers for my card and it has been a frustrating day. I guess I'm not cut to be a network analyst just yet.
System specs:
ASUS P5Q SE/R
Intel Core 2 Quad Q9550
4GB DDR2 667
Gigabyte GTX465 1G
TP LINK TL-WN851N Wireless card
I know that most people are using F12 and F13 but I just installed F10 on one of my machines. The Kernel is 2.6.27.5-117.fc10.i686 and the GUI is Gnome 2.24.1.I have a Trendnet wireless card already installed in the machine from when it ran XP which is in the tew-421pc/tew-423pi family. Is there a device manager/hardware installer that I can use to set up the wireless card or does anyone know of a driver install program for this card?
View 1 Replies View RelatedIssue: Using Fedora-14-x86_64-Live-Desktop.iso, I created a live usb and tried it on Dell M6400. I can boot into F14, see the internal hard-drive and other usb drives -- but F14 will not go on the network -- neither wired or wl networks.
I am not sure what additional information I need to provide to help resolve this issue. Perhaps some background info would help?: I am trying to move from XP to linux on the M6400. The latest Ubuntu live CD would not boot, the latest CentOS live CD could not find the internal drive; I got best results with the latest Fedora (and I am more comfortable with the F14 gnome interface than the F14 KDE, the Ubuntu, and the CentOS interfaces). I do not know how to investigate the inability of F14 to detect the ethernet cabled network. I was unsuccessful in my attempts to get the wireless to work: "lspci -nn" shows BCM4322 802.11a/b/g/n 14e4:4326 (rev01). I read [URL]../docs/linux_sta/README.txt and used what I learned in my attempts. Installing broadcom-wl-5.60.48.36-1.fc13.noarch.rpm, kmod-wl-2.6.35.6-48.fc14.x86_64-5.60.48.36-2.fc14.2.x86_64.rpm, and kmod-wl-5.60.48.36-2.fc14.2.x86_64.rpm (found at rpmfusion) did not help. I tried to build and install the sources from http://www.broadcom.com/support/802.11/linux_sta.php; the machines I had for building were 2.6.28-18-generic Ubuntu, fc5, and rhel5 -- attempts with these builds failed too.
I have a Netgear WG511GE PCMCIA card, and a driver from the original installation disk. I used an ndiswrapper-utils gui called ndisgtk to install the driver. I then do the following to verify an installation:
[Code]....
Unfortunately, when I put the PCMCIA card in, nothing happens. On Windows, a green light flashes even if the card is not connected to any network. At first I thought this might be a hardware issue, so I did #lspci and got:
[Code]....
Lo and behold, when I put a different unbranded Wireless PC Card in it works. I'm no expert in Networks, but to me this suggests a driver problem (i.e. the card is physically detected it just won't work). However, the correct driver was installed with ndisgtk and this was verified with #ndiswrapper -l, hence the confusion.
I'd be grateful if anyone else has had this problem/knows of this problem and is willing to share the solution with me/point me in the right direction. So far, Google has returned a few posts from a few years ago talking about patching kernels and manually building files etc (just before Prism54 became integrated into the Linux kernel).
I have downloaded and installed Fedora 10.Now I am setting up the network and in the 'network configuration' it finds the wireless device (ralink) in the 'hardware' section of the configuration - I set this to eth0 (it originally set itself to wan0 and I still had the same problems, now it doesn't give me the option to put it back to wan0).Now I goto the devices tab and try to set up the device with eth0 - which it seems to find.But when I goto activate the device it tells me that eth0 cannot be found
View 2 Replies View RelatedI just installed x64 Fedora, and as the title says, NM fails to detect my WiFi card. It's an Encore ENLWI-N with a RaLink RT2800 chipset. The card does show up when I run lspci, although iwconfig yields nothing.Not sure if this helps, but when Ias running Karmic Koala, Ubuntu detected the card immediately and required no configuration
View 2 Replies View RelatedI normally connect to a free wireless project, and did have a Windows box until yesterday when I installed Fedora 10. When I was using Windows, I was able to connect to the unsecured wireless network. Now on Fedora 10, the wireless card is working and is able to pick up signals but the signal strengths are markedly decreased and I am unable to see the network which I usually connected to.I really don't want to go back to Windows.
View 12 Replies View RelatedIm just after installing fedora 12 dual boot with windows 7. When I try to find my wireless network the laptop doesn't seem to picking it up. It works perfectly when I connect with a LAN cable.
View 2 Replies View RelatedI have installed open suse 11.3 with no issue, but I can't find the dirvers for the wireless network card/
Wireless, Half Mini-Card, DW1520
I need to test network card throughput and speed between two computers, one is running Fedora and other running Windows 7. Usually I would use netperf to perform this task, however I can't find Windows build of netperf. Can anyone recommend any network evaluation tool, similar to netperf (clien/server) which has both Windows and Linux versions.
View 2 Replies View RelatedI am unable to access wireless network from my notebook. My configuration is Dell i5, 4GB RAM and 1397 W-LAN and I have F13. I can still access Internet through Ethernet using a LAN cable but the network monitor doesn't show list of Wireless networks which my room mate's windows 7 machine easily detects.
If anyone needs more info please provide me the steps to perform to find that out
I cant get openSuse to find my wifi adapter or it does not have the driver installed.
My wifi adapter is the Realtek RTL8191SE 902.11b/g/n
I found a linux driver on the internet, but it asked me to run make in the console and when I did so it said that it couldn't find make.
how to install make from openSuse without the internet (I'm using my windows partition).
I am trying to install Debian Lenny via Hyper-V. I get to the point where it asks for the network card. For some reason it can not find my network card. I have a RealTek (RTL8112L PCIe Gigabit LAN controller featuring AI NET 2 built on motherboard).
For some reason it doesn't see it. My issue is if I continue without the network how am I getting the drivers? Unfortunately Hyper-V doesn't support USB. I guess I can try to burn to CD but not looking to waste a cd for 480k and not sure that will work as I only see a auto.sh and a couple other files under scr directory. If anyone has any ideas please let me know. This is a fairly new Motherboard/NIC so I do not understand why it isn't recognized. I know it cant have everything but Realtek is a fairly common nic.
I installed the driver for my network card. iwconfig and ifconfig are all responsive to connecting to the network, I'm given an access point address. Then, I try to connect to a website and no dice. ping www.google.com yields no result. What gives?
View 2 Replies View Relatedmy wireless home network is not recognized by my network card (RealTek RTL8190 mini PCI). The post was as follows: "I am using a new computer with Windows 7 , Athlon quad core 2.60 64 bit, 8GB RAM. Internet conection works fine with ethernet but ubuntu does not see my wireless network. card (RealTek RTL 8190 ID: 10ec:8190). Have searched this forum but unable to come up with a fix. I was looking for windows XP drivers to use Ndiswrapper but could not find a list of .inf files. My network is OK and works perfectly in windows and with my 2 laptops. Can anyone point me in the right direction? Additional info: install was done within Windows using WUBI to a separate partition on my HDD. I am new to this and thouroughly confused as to the procedure for installing the drivers if they are in fact available."
I am very frustrated in that I would like to use Ubuntu 10.04 but it is useless without internet connectability. I am new to linux and do not understand where to get the appropriate drivers or how to install them. I wish someone would answer this post and either give me a clue what to do or just say "give up" and uninstall ubunutu.
ubuntu wont find a at&t 3G sim card..it doesent even show up as hardware on the network manager.what can i do to fix this?
View 3 Replies View Relatedi can not find the network storage drive on my MS network using Ubuntu.i can find other computer using xSMBrowser but not the hard drive connected to my router (LAN)i have tried samba and a few others
View 5 Replies View RelatedI have a Broadcom Corporation NetXtreme BCM5721 network card on my server at work.Everything works fine for a few weeks, then randomly the network connection on the server will stop working. After it stops working, I will try to reconnect with the network manager, it shows a wired connection available, it shows the "connection in progress"animation, then the "connection disabled" icon.
I uninstalled the network manager and used manual configuration, but do you think the network manager was the issue? I can't have the server disconnecting randomly every few weeks with no way to know what the real problem is. Was there an issue with the network manager with 10.04?
Ubuntu 9.04 running on a Dell C640 with a Dell TrueMobile 1150 wireless card. Works perfectly under XP. Ubuntu can't find it. Wired networking finds the internet perfectly (though I'm still working on getting samba set up correctly for file/print sharing on my XP LAN).
I'm thinking I need a driver, maybe? Can't seem to locate one.
Mandirva cant find my internet card.or is it just me?
View 5 Replies View RelatedI have a laptop connected to the the net thru an adsl modem, when I switch off the laptop network interface,(thru system-config-network) the light of the laptop network card plugged in the router stays on ( green) where as in my pc, when i do the same thing , the light of my pc network card goes off in the modem
View 5 Replies View RelatedI know some wireless card can work in Master Mode but it seems use madwifi driver. I know madwifi doesn't support usb dongles find a usb wireless card which can work as AP under Ubuntu. I have check this list [URL] I am not sure if ar9170usb.ko and its device support Master MOde.
View 6 Replies View Relatedive just installed the aircrack package in my dell vostro 1310 which i bought with its ordinary wireless card ( hell knows what it is. couldn't find..).At the very first time while trying to reach my wireless internet i was using backtrack 4 and i was not sucesfull.. that would be good normally, but it was not. because i couldnt do it cuz my wireless card wasnt being recognized by airmon..so i tought..i can use my wireless with ubuntu... then i got ubuntu again.. and intalled the aircrack.. as i run it i found ou t that still it wont find my wireless card...do i need any further config. to make it work with aircrack ??i can only find eth0, which is my wired network device....
View 1 Replies View RelatedI'm new to Ubuntu. Today, I took my old Compaq Presario V3010US and gave it life with Ubuntu 10.04. The hard drive was erased and replaced with the Linux OS stuff. Ubuntu recognizes most of the hardware except my Broadcom wireless card. I find this to be a pain because i'm a newbie to linux stuff. Anyway, can anyone help me fix this? I thank you for your time reading this.
View 1 Replies View RelatedI have in my ubuntu 3 eth?
eth0
eth1
eth2
just eth1 has an IP address...
I just have remote access to the server via ssh.
How do I find out which eth0 is a fiber nic ? Because I know one of them are.. but I cannot assign any IP address to them..
which eth? belongs to this fiber nic ?