On my HP i7 based laptop the latest kernel 2.6.33-147 and possibly Nouveau/X.org seems to have broken suspend. ie If the laptop is suspended then when woke, the screen is dead and networking does not work and I cannot change to a different console.If I boot the previous kernel this behaviour does not occur.
View 6 Replies
I just updated my kernel to the latest version (2.6.35-24). Now my suspend function on my Thinkpad SL510 no longer works. The system simply hangs with a solid cursor in the corner of a black screen. USB devices remain powered on, HDD keeps spinning, and all indicator lights remain lit. When this happens, the only thing I can do is hold the power button down for a hard power off.My first thought would be to troubleshoot this with dmesg, but I don't know how to record dmesg after a power off. The message buffer is reset when I reboot.
View 1 Replies View RelatedMy system with kernel-2.6.35.10-74.fc14.x86_64, NVIDIA 3800 + Samsung 2233 and 3Dvision kit works fine, but upon upgrading to kernel-2.6.35.13-92.fc14.x86_64 the system won't go past the blue->white bar along the screen. The modprobe.d directory has the file blacklisting nouveau and there is the grub entry rdblacklist=nouveau, but do I need to re-run the nvidia installer. If so I think I need to reset the init level to stop X11 trying to load. and will I need to keep doing this everytime I upgrade the kernel if I have nvidia drivers installed?
Leigh123linux desired code output is below
***
abrt-addon-kerneloops-1.1.18-1.fc14.x86_64
kernel-2.6.35.10-74.fc14.x86_64
kernel-2.6.35.13-91.fc14.x86_64
[Code]....
I just wanted to check, I'm using nouveau on Fedora 12 with the latest updates and each time I wake the machine from suspend, the fan on my XFX 8800GT goes to full speed and stays there. I've read some nouveau stuff and they say that nouveau doesn't control the fan speed, so I think the card is running in a safety mode after wake up where it runs the fan at full speed to be safe. The only suggestion I saw for fan speed and nouveau was to use nvclock to manually adjust the fan but that sounds dangerous to me. I think I'll just go to the closed rpmfusion driver then if this is the case.
View 3 Replies View RelatedI installed Chromium via a repo generously maintained by Tom "Spot" Callaway. Since it's his repo I thought I'd contact him, but I don't really know how - so I'm brining my issue to the forum to see if anyone has a possible solution.I've been using Tom's Chromium fine for the past couple months. After a "yum update", Flash no longer works in Chromium. It works in Firefox. If I try to play any Flash videos it's just a blank box.
View 3 Replies View RelatedI have sometimes use my PC for games, thus i need EAX support from this. Linux X-Fi drivers works well, exept it's prevent my system to go S3 standby. If i do blacklist snd_ctxfi suspend works after reboot.
View 5 Replies View RelatedI have Lenovo T410 with NVIDIA NVS 3100m running nouveau driver/F13. When I updated to the latest kernel, the display goes blank when booting and remains blank. I can ssh to the machine, so - it appears to be an X/display issue. All else seems to be working normally, and I didn't spot anything of interest in the logs - but perhaps I don't know what to look for.
Also, it appears to be an issue in the kernel package rather than in the nouveau driver package. I can still boot the former kernel successfully - even with the new driver files.
The previous kernel version was the version of the kernel that is provided with the initial F13 install.
[URL]
I'm not sure what changed but when I recently upgraded via yum to Kernel 2.6.34 none of my uPnP or DLNA apps show up on my tvs (Sony TV and PS3). Booting an older version, i.e. 2.6.33 solves the problem with no other changes. I use MediaTomb, MythTV uPNP server and Serviio. All work fine except with the newest kernel.
View 8 Replies View RelatedI run an Aspire One 522 with a Broadcom BCM4313-Wlan-Card and Fedora 15. To run the card, I had to install der broadcom-wl-Driver, as described here: [URL]... It worked okay. (Althought not perfect. It crushed everytime the whole system, when it tried to connect to a WLAN-Net, unless I first started the Windows on the computer, then shut it down and restarted Fedora. But maybe thats some strange Dual-Boot-thing.) Anyway. After I updated the Kernel to 2.6.40 it seems to be broken. I deleted the driver, reinstalled it, tried the B43-driver. But no mater what: It seems like the NetworkManager doesn't find the card at all. lsmod shows that a modul "wl" is running. And - as mentioned - I installed the Kernel and the two other packages fresh form the repositories.
View 3 Replies View RelatedAnyone knows the easiest way to switch from the nvidia drivers to teh nouveau drivers in the latest kernel?
View 2 Replies View RelatedI have installed the latest virtualbox 4.1 on my desktop and laptop. It hosed suspend and hibernate.
The laptop is A Dell D630 with Intel Core2 Duo CPU, the desktop is an AMD based ASUS M3N78-VM mobo with Athlon II x2 250 CPU. Debian Testing 32-bit (same results with the 2.6.39 and the 3.0 kernels). Both have nvidia cards though - the desktop an integrated 8200, the laptop a NVS 135M. But suspend/hibernate was working before with the 4.0 series virtualbox.
The workaround is to clear the vboxpci vboxnetadp vboxnetflt vboxdrv modules from the memory before suspend/hibernate. I added the
service vboxdrv stop
rmmod vboxpci vboxnetadp vboxnetflt vboxdrv
lines to my sleep script (i dont use power managers, just the acpi powerbutton/lid scripts modified). Everything is ok now.
The updated Kernel 2.6.32.26.175.fc12 (i686) broke nVidia 96xx drivers (nVidia MX-4000 card).Resulted in a quickly flashing cursor in the upper left corner, with no X startup.I removed the driver and let it rebuild using akmod. Still have the same problem.When I revert back to the previous kernel 2.6.32.23-170.fc12.i686, all is well.At this point, wonder what the chances are of this being fixed? Seems the last set of updates before EOL of a release always breaks something critical.
View 6 Replies View Relatedkernel-2.6.32.10-90.fc12 seems to break 802.11n with my intel 4965 chip on my thinkpad t61p. Anyone else seeing the same thing? iwconfig shows extremely low bit rate. dmesg doesn't show anything at all unusual.
View 10 Replies View RelatedI'm on 10.04.I was curious to see the new features implemented (mainly geo-location) in Empathy, so I added their PPA and did an update. After updating, the notifications for Empathy become separated from the MeMenu (separate icons, no 'Chat' option is specified when I click the MeMenu), although I can still update my status by clicking on my user name.Does anyone know how to integrate the new Empathy back into MeMenu? If not, how can I roll back to the previous Empathy version that works with MeMenu?
View 5 Replies View RelatedI'm running Virtualbox from the Sun website (need the USB support) and it breaks after each kernel update.The problem is that I installed a lot of Ubuntu systems for transitioning windows users with Windows in virtualbox to ease the migration but I have to rerun vboxdrv setup after each kernel patch.
View 2 Replies View RelatedI've noticed a bad behaviour with the latest 2 Fedora kernel releases:
- it happens with 2.6.31.12-174.2.19.fc12.x86_64 and 2.6.31.12-174.2.3.fc12.x86_64
- but 2.6.31.9-174.fc12.x86_64 is OK
The problem is as follows: Any kind of terminal application (any X based terminal and the console itself) hangs on certain operations involving colors from what I've seen
E.g. 'ls -F --color' as predefined in Fedora works but 'ls -F --color -a' hangs. Midnight Commander also hangs but works on black and white.
My terminal is xterm-256color under X and linux under console.
Other observations:
- it happens on a AMD machine but not on an Intel i.e. not all hardware is affected (couldn't narrow it more)
- same machine, same software stack but with kernel 2.6.31.9-174.fc12.x86_64 works OK
The latest kernel(2.6.32.9-67) is causing problems for my laptop.What are the best practices for safely removing a kernel?( Yum wants to remove gcc and friends also...)How can one prevent Software Update from relisting the bad boy?
View 6 Replies View RelatedAnyone know what happened here or what I need to do? I'm running Fedora 12 and had the nvidia video driver setup and working perfectly from rpmfusion repo ... I just did a yum update and now my display is stuck on 800X600 ....
View 14 Replies View RelatedI have a Macbook Pro 5,5. I had Fedora 14 installed on it, updated to the latest version. I updated the kernel, and performed an update. Now, every time my system starts, it loads up the startup fedora bar, and it gets stuck at the bar being loaded 100%.I press ESC to see what is going on behind the scenes, and I notice that the problem is that atd cannot start up.
View 2 Replies View RelatedI need to download a latest kernel for my fedora ..and reconfigure it with some options.
Where can i download latest fedora kernel source code from ..
I am relatively new to the Linux System (8 months). I am having issues after upgrading the Scientific Linux 6 kernel from its current 2.6.x version to the latest version that SL6 has available. The issue is that once I install the upgrade and reboot, the internet becomes extremely laggy when scrolling on web pages, so much so that you get a ripple like effect as your scrolling. Which doesn't occur in the current kernel i am using.
Current Kernel is: 2.6.32-71.18.2.el6
New Kernel RPM update is: 2.6.32-71.29.1.el6
I wish I could figure out the problem but I am having trouble identifying what exactly the current kernel has that the new one doesn't that would cause the internet lag. I have read other topics with similar kernel update problems, but none have expressed an internet problem & only an internet problem from a kernel update.
I am running the 64-bit version of Fedora 12 on an MacBookPro5,1 Intel Core 2 Duo with 4 Gigabytes or RAM.
I updated my system to use kernel 2.6.32.16-141.fc12.x86_64. Now when I try to boot the machine to that kernel, I'm left with a blank screen except for a blinking underscore cursor in the upper left corner after going through the load progress bar animation that appears at the bottom of the scene when Fedora is booting up.
I have my system configured to use the nVidia drivers for OpenGL 3D acceleration
I have to boot to previous kernel to have a usable system.
What can I do so that the system will boot up properly with the latest kernel?
I'm running 10.10 on a Lenovo x200. I have been running, happily, with 10.10. Yesterday, the update manager installed:
PHP Code:
After this update I am unable to Suspend. The screen goes black, the harddisk spins, the moon blinks a couple of time and then I'm presented with the Lock Screen.
I have:
Kernel Linux 2.6.35-25-generic-pae
3.6 Gib of Memory
Availabe disk space of 75.6 GB
Dual Boot: Fedora 12 and XP Dell 505I've had trouble with the latest kernel update.I updated a bunch of packages recently (including Xorg and kernel), and noticed a severe flickering after the update on my center monitor (Samsung T260 - the laptop display did not exhibit the flickering behavior). I backed out all the changes and started updating package by package. After I updated the kernel (again) I rebooted and here's where the fun part is -
I no longer get anything, except the cursor. No grub menu, no grub prompt. I rebooted and ran the rescue disk and followed the procedurery and point grub at the right boot partition - see here. However (obviously or I wouldn't be posting) that failed to work. I still get a blinking cursor and dead system on boot up.
Last night I installed F12 x86_64 from a liveUSB in my laptop with Atheros wireless. During the install process and after the first boot I was able to surf the web connected to the wireless network (signal was good and all). After I updated the whole system, however, the wireless network is no longer available (Network Manager does not even show the Wireless interface or the network list).
Obviously a laptop without wireless is mostly worthless. What am I supposed to do to get my (perfectly working*) wireless network back?
[Code]...
I have install windows XP and Fedora-14-X86_64 on dual boot, I want to run other OS on fedora by using Virtual machine. I have download and installed VirtaulBox-4.0.0 successfully but I cannot able to start it. I got error about Vbox driver not installed [error code:1908]. I have also installed DKMS package, but also didn't work.
Finally I found the actual problem was kernel not compatible with latest version of vbox and I need to update my kernel-headers. I also meet that solution by using command: yum install binutils gcc make patch libgomp glibc-headers glibc-devel kernel-headers kernel-devel and its work fine, this command download and install the kernel compatible VirtualBox-3.2.* and now its works fine.
But problem is that when I booting my PC, it shows 3 options for entering OS rather then 2.
1. Fedora-14 (2.6.35.10.74.X86_64) [which is new one/updated after using that command]
2. Fedora-14 (2.6.35.6.45fc14.X86_64) [which is new one/updated after using that command]
3. Other [windows XP]
How can i delete that old version- No.2?
The latest installed kernel stopped working. ( 2.6.35.13-92.fc14.i686) It won't boot. I just get black screen with blinking cursor in top left corner. How do I, or can I, remove and reinstall?
View 4 Replies View RelatedI seem unable to get an nvidia driver working properly after upgrading to the latest kernel with Fedora 11.Here is my laptop and its specs: http://h10025.www1.hp.com/ewfrf/wc/d...reg_R1002_USEN[URL]I've tried both the kmod and akmod unsuccessfully. Everytime it gives me a black screen on boot, I can fix the problem by popping in the LiveCD, and changing the xorg.conf file back to the backup.Here are the errors/warnings from my boot.log file:
Code:
WARNING: Deprecated config file /etc/modprobe.conf, all config files belong into /etc/modprobe.d/.
Checking for module nvidia.ko: [60G[[0;31mFAILED[0;39m]
[code].....
I'd like to run a real-time kernel with the latest linux-rt patch, for 2.6.33. Incidentally, the .33 kernel was the first to include the Nouveau driver, and seeing that I cannot get the proprietary NVidia driver to compile --the RT patch really messes things up and the patches for nv-linux.h out there all seem incomplete-- I thought it would be a good idea to switch to Nouveau and save me from additional headaches.
I'm running sid, and as you certainly know, the Nouveau driver has been backported to the stock Debian kernel, 2.6.32-5-686. It works very well, all I had to do was change my xorg.conf with this line : Driver "nouveau".
However, when I boot my new 2.6.33-rt kernel, Xorg stops here :
[skipping a lot of stuff that seems to work ok]
(II) LoadModule: "nouveau"
(II) Loading /usr/lib/xorg/modules/drivers/nouveau_drv.so
(II) Module nouveau: vendor="X.Org Foundation"
compiled for 1.7.7, module version = 0.0.15
[Code]....
So what is so different about the backport to 2.6.32 ? How come the DRM lib, or whatever it is, doesn't work with 2.6.33 ?
I just thought of something, I'll try compiling my 2.6.33 kernel without the -rt patch and I'll let you know.
It seems that updating the Kernel breaks my installation. I've tried it twice, and both times it disabled my gui desktop. I'm posting this with links2 in my terminal. The terminal works perfectly.
This is really annoying, as I can't even use my computer. What do you think is the problem?
