Fedora :: Nvidia Driver Locks Computer Up On Startup After Latest Kernel Update?
Oct 18, 2009
I seem unable to get an nvidia driver working properly after upgrading to the latest kernel with Fedora 11.Here is my laptop and its specs: http://h10025.www1.hp.com/ewfrf/wc/d...reg_R1002_USEN[URL]I've tried both the kmod and akmod unsuccessfully. Everytime it gives me a black screen on boot, I can fix the problem by popping in the LiveCD, and changing the xorg.conf file back to the backup.Here are the errors/warnings from my boot.log file:
Code:
WARNING: Deprecated config file /etc/modprobe.conf, all config files belong into /etc/modprobe.d/.
Checking for module nvidia.ko: [60G[[0;31mFAILED[0;39m]
[code].....
View 6 Replies
ADVERTISEMENT
Dec 26, 2009
i ran yum update which updated kernel to 2.6.31.9.174.fc12.i686.PAE. Now after logging in i get a blank white screen. With previous kernel updates i have had no such problem. Anyway, the boot messages are following:
Quote:
checking for module nvidia.ko [FAILED]
nvidia.ko for kernel 2.6.31.9-174.fc12.i686.PAE was not found [WARNING]
The nvidia driver will not be enabled until one is found [WARNING]
Driver already disabled
I have a GF 6600 video card.
View 14 Replies
View Related
May 11, 2011
I just updated to kernel 2.6.35.13-91.fc14.x86_64, and I'm now having a weird issue where my computer will hang during startup and shutdown unless I move the mouse around.
While moving the mouse, it will boot up or shut down normally. Once i stop moving the mouse around it will hang (until I begin to move the mouse again).Once fully booted it acts fine..
View 13 Replies
View Related
Oct 29, 2010
I'm running Fedora 13 x64 and updated the kernel to the latest version (2.6.34.7-56 to 2.6.34.7-61). I use the proprietary nvidia drivers (currently 260.19.12) so I had to compile the kernel module against the new kernel sources and reinstall the driver. The process was apparently successful, but when I try to start X nothing happens, it's as if the computer had been suspended, my monitor acts like it isn't receiving any input. I have full runlevel 3 access, and the system seems pretty much fine up to that point. Nvidia's own sanity tests which are built into the installer reported no problems with my driver.
View 14 Replies
View Related
Jun 26, 2011
Lately (F14 and F15), Nvidia's drivers have been making my system freeze unexpectedly when running X. The only work around I have is reverting to an older driver (173.14.30). Although no freezes occur when using the older one, I need the latest one to run a few games sometimes. The odd thing is that when running these games within Wine while having the latest driver installed prevents the system from its usual freeze. I'd just like to solve this problem so I don't have to consistently revert back and forth from the two. I have a Nvidia Geforce 8800m gts and I am running F15 x86_64.
View 14 Replies
View Related
Jun 15, 2010
Anyone know what happened here or what I need to do? I'm running Fedora 12 and had the nvidia video driver setup and working perfectly from rpmfusion repo ... I just did a yum update and now my display is stuck on 800X600 ....
View 14 Replies
View Related
Nov 19, 2009
I compiled the 2.6.31.6 kernel and <insert drumroll> it boots!(my first kernel roll, I'm kind of shocked actually) That's the good news. The bad news is that my NVIDIA drivers are gone in the wind. That's not entirely true as I can still boot into the old kernel and startx. Is there a way to download the driver using the command line for reinstall?
View 4 Replies
View Related
May 11, 2011
I have a Macbook Pro 5,5. I had Fedora 14 installed on it, updated to the latest version. I updated the kernel, and performed an update. Now, every time my system starts, it loads up the startup fedora bar, and it gets stuck at the bar being loaded 100%.I press ESC to see what is going on behind the scenes, and I notice that the problem is that atd cannot start up.
View 2 Replies
View Related
Jul 4, 2010
my problem is on installing nvidia driver on fc12 32bit but, first of all, as i understood the pae kernel requires more than 4gb of ram,i have a 2.2 ghz cpu with 2 gb ram,but when i run command:uname -r it answers: 2.6.31.5-127.PAE [i have fc12 32 bit] when we try to download linux we have a 32bit edition or 64bit edition,do we have an edition which is only for pae? or when we install for example the 32bit edition on a computer with more than 4gb of ram then the kernel automatically will change to be a pae kernel??
View 10 Replies
View Related
Mar 14, 2010
Dual Boot: Fedora 12 and XP Dell 505I've had trouble with the latest kernel update.I updated a bunch of packages recently (including Xorg and kernel), and noticed a severe flickering after the update on my center monitor (Samsung T260 - the laptop display did not exhibit the flickering behavior). I backed out all the changes and started updating package by package. After I updated the kernel (again) I rebooted and here's where the fun part is -
I no longer get anything, except the cursor. No grub menu, no grub prompt. I rebooted and ran the rescue disk and followed the procedurery and point grub at the right boot partition - see here. However (obviously or I wouldn't be posting) that failed to work. I still get a blinking cursor and dead system on boot up.
View 9 Replies
View Related
Sep 27, 2010
Having just updated various files including the kernel using Package Manager I no longer seem to have the correct version of the Nvidia graphics driver. On previous updates this has been done automatically by the "kmod Nvidia" Metapackage. My last kernel was 2.6.32.19-163 fc12.i686.PAE and the Nvidia driver for that did get downloaded correctly. Looking on Yumex I cannot see a driver for this latest kernel listed.
View 10 Replies
View Related
Mar 10, 2010
What is the best way to begin troubleshooting startup problems after kernel update to 2.6.31.12-174.22.fc12.x86-64? Since updating, I am experiencing frequent system hangs at startup.
View 5 Replies
View Related
Oct 30, 2010
[URL]. I now have both monitor working and noticed my drivers are not current. I have the older ones installed. The 260.19.06 one. I installed via the suggested restricted driver utility in ubuntu 10.10. I don't have full use of the graphics and would like to install the latest driver.
Question:
1. Do I uninstall nouvea and nv drivers (still installed)
2. Do I uninstall the current nvidia driver, then do a manual install of the latest driver from nvidia?
View 5 Replies
View Related
Apr 12, 2011
I just responded to a (packagekit?) prompt to update packages, which included new kernel 2.6.35.12-88.fc14.x86_64. I use nVidia on my notebook and usually the new driver is installed automatically. This time, the computer would not boot to the stage that the nVidia logo appears, indicating the driver is not present. I edited grub.conf to take me back a version and I am now running under the previous kernel 2.6.35.11-83.fc14.x86_64. I tried a yum search for kmod-nvidia-2.6.35.12-88.fc14.x86_64 and nothing was found. I have enabled these repos:
[Code]...
View 4 Replies
View Related
Mar 11, 2010
I updated my fedora 12 GNOME installation. Now Compiz fusion is not working. It says Accelerated 3D support not found. Though Nvidia drivers are already installed. Now I can't even ALT+TAB between open applications.
I tried "metacity -- replace" but then windows wore a weird look with only a minimize button. No sign of maximise & close buttons.
View 14 Replies
View Related
Jan 30, 2011
I had a working ubuntu 10.10 system two days ago with kernel 2.6.35-24. I have a gtx 460 card so I have the driver from Jockey/Additional Drivers installed.
Two days ago update manager prompted me to install 2.6.35-25. I've never had problems updating kernels so I did. I Rebooted my machine and gdm/gnome no longer starts. I always get stuck on the tty1 screen. I did some troubleshooting and figured out that my current NVidia drivers seems to be messing it up. So I booted into my older kernel (2.6.35-24) and removed my NVidia driver.
I used these steps to switch from nvidia to nouveau:
NvidiaDriverSwitching
I can now boot into my latest kernel (2.6.35-25) but now I'm having problems trying to reinstall the nvidia drivers.
jockey sometimes doesn't list any available drivers. and when it does, it gives me an "System InstallArchive() error" when trying to install.
I tried installing nvidia-current via apt-get and I get these errors:
Code:
Setting up nvidia-current (260.19.06-0ubuntu1) ...
Removing old nvidia-current-260.19.06 DKMS files...
dkms.conf: Error! No 'DEST_MODULE_LOCATION' directive specified.
dkms.conf: Error! No 'PACKAGE_NAME' directive specified.
dkms.conf: Error! No 'PACKAGE_VERSION' directive specified.
View 7 Replies
View Related
Nov 18, 2010
I used to have FC11 installed with the nvidia supplied binary driver. Worked fine, very stable. Trying FC12 and FC13 live CDs caused a hang, so I stuck with FC11. FC14 live CD did boot so I backed up my own files and did a clean FC14 install. Upgraded to get kernel 2.6.35.6-48, installed the nvidia driver from RPMFusion (260.19.21) and had a working system! Now, after a cold boot, the kernel always hangs during boot. Tried a number of kernel boot option (apci=off, noapic and a few others too). The hang is not always at the same place. The earliest it has hung is after:Disabling lock debugging due to kernel taint
Sometimes its a few lines later at:NVRM: loading NVIDIA UNIX x86_64 Kernel Module 260.19.12 ...(which would seem to imply that the hang can even occur a step or two before the actual driver is loaded!)
Sometimes it keeps going for a few more seconds and randomly hangs during some other driver load.
Without a specific nvidia driver the system always boots ok, so I'm pretty sure its the nvidia driver but I just can't seem to get a handle on this in a reproducible way. Sometimes, when I have make some other change, it will boot and work ok, but a reboot locks it up again (for example, in case it was SELinux, I disabled it and on the next reboot it booted and worked ok. Then, next boot, it wasn't working again). When I make changes, I reboot using the previous kernel, make the changes and reboot, with an occasional success. Once I start rebooting using the latest kernel, it always hangs.
I'd love to get a solution to this, but even some advice on debugging this would be appreciated!
I'm using 8600GT, 256Mb, PCIe card in a MA69VM motherboard with 3Gb of RAM.
View 2 Replies
View Related
Jun 17, 2010
I read somewhere that when updating Fedora I might want ttemporarily disable userdefined repos like RPMfusion.I tried that with
Code:
yum upgrade --disablerepo=rpmfusion-free-updates
It updated, I rebooted, and now my nvidia driver is not found.
[code]...
View 2 Replies
View Related
Oct 30, 2010
a little while ago the file from nv stopped being able to run.. I cant update the driver and now always get this error
4: warning: comparison between signed and unsigned integer expressions
/tmp/selfgz2718/NVIDIA-Linux-x86_64-260.19.12/kernel/nv.c: In function �nv
_kern_read_registry�:
[code]....
View 2 Replies
View Related
Jun 21, 2011
Lately I tried to update my nvidia drivers from RPFMFusion repos. There was a new version 275 available, so I installed it. After a reboot I would repeatedly see the Nviia Logo followed by black followed by a glimpse at the CLI with some error message. This process continues over and over again and it is so fast that the only thing I could make out from the error message is the following:
at-spi-bus-laun[some-number] segfault at 980 ...
in libx11.so.6.3.0 ...
I tried completely removing the driver then updating my system (there were no updates) then booting with nouveau to see that that actually works. Then I tried reinstalling the nvidia driver following leigh's guide [URL]. Same error.
This is where I'm stuck at the moment. Booting to runlevel 3 I had a look into the messages and Xorg.0.log, but I didn't see anything. Maybe I can get the log files uploaded.
I will boot from live media and provide them later on.
Hardware specs:
Samsung P480
Intel corei3 330
nvidia GT330M 1024mb
8gb Ram
120gb SSD OZC Vertex 2 with /tmp mounted as tmpfs
Software specs:
Using F15 x64
kernel 2.6.38.8-32 (from the top of my head, please don't shoot me)
added repos:
RPMFusion
adobe (flash)
playonlinux
There is one addition I can make. Before, when I was using the 270 driver, I tried playing some games via wine and that also segfaulted on me (most of the time - 1 worked), so I think there is a general issue with the nvidia drivers on my system. But back then It was only wine, not X.
View 9 Replies
View Related
Jun 17, 2011
I updated FC14 which included the kernel and also the nvidia drivers kmod. Then after a reboot the video driver wouldn't load. From another terminal I tried different things to fix it and didn't managed. I eventually erased all nvidia drivers so that I can get the default one. Now every time it boots I get a really low light. I can login, but can't see. It seems that the whole screens has about 5% light and I can't see to do anything. I managed now to boot into FC live CD for FC15 and I have light. For FC14 live CD it's the same no light problem.
I tried all older kernels to boot but I have the same problem. I am using PAE kernel and that's why I installed the kmod drivers. But now, since they are not anymore and I can't see anything, even though I am logged in I don't know what to do next. Is there something I can do from FC15 live cd? How can I go using the terminal to my harddisk and how to add the driver or any low graphic driver so that I can have light? After I did yum erase *nvidia* the light went almost off.
View 2 Replies
View Related
Oct 24, 2010
The first thing I do is press ctrl-alt-f1. Then I do this:
Code: sudo su
init 3
./NVIDIA-linux-x86-260.19.12.run Then it comes up with the error that I have X-server running.
I've also tried Code: /etc/init.d/gdm stop but that command wasn't recognised. I've also tried Code: killall -9 X but there are no processes called X
View 2 Replies
View Related
May 4, 2011
I've been trying to install the latest NVIDIA driver for my 7800GS card. dl the driver from NVIDIA. ctrl+alt+F1. stop gdm3, after I hit agree I get an error. The CC version check failed: The compiler used to compile the kernel (gcc4.3) dows not match the current compiler (gcc4.4). The Linux 2.6 kernel module loader rejects kernel module built with a..
View 3 Replies
View Related
Oct 13, 2009
I have been running F11 for some time now. I install updates regularly and to this time have had no issues. Now it comes up with error.
Code:
[root@red 2305 ~]
$ yum update
Loaded plugins: protectbase, refresh-packagekit
0 packages excluded due to repository protections
Setting up Update Process
Resolving Dependencies
--> Running transaction check .....
--> xorg-x11-drv-nvidia conflicts with xorg-x11-drv-catalyst
Error: xorg-x11-drv-nvidia conflicts with xorg-x11-drv-catalyst
Error: xorg-x11-drv-catalyst conflicts with xorg-x11-drv-nvidia
You could try using --skip-broken to work around the problem
You could try running: package-cleanup --problems
package-cleanup --dupes
rpm -Va --nofiles --nodigest
[root@red 2306 ~]
I do not believe that I even have the 'xorg-x11-drv-catalyst' mentioned here installed:
Code:
[root@red 2315 ~]
$ yum list all | grep installed | grep catalyst
[root@red 2316 ~]
This returns nothing so why the error?
View 5 Replies
View Related
Jul 12, 2011
I have just updated my kernel to version 2.6.38.8-35 in Fedora 15, it now refuses to boot that kernel. I just get a lot of text on the screen and nothing happens. I can ctrl-alt-fn to get to a prompt, but I do not know how to fix the nvidia problem.
When I edit Xorg.conf and replace 'nvidia' with 'nv' the new kernel boots but only to fallback mode, trying to then re-install the nvidia drivers shows them to be already installed and I can get no further.
View 13 Replies
View Related
Apr 12, 2011
After the latest update of testing, Debian started to reboot at at startup, after just few messages shown (that's all after GRUB choice is made). If I pick up older kernel it boots OK. What should I look for to determine the cause? (I.e. what log etc.).
View 4 Replies
View Related
Sep 1, 2010
Fedora (2.6.34.6-47.fc13.x86_64) I installed that update, during the installation process it said that it had to remove three packages, one of them was kmod nvidia for the old kernel (Fedora (2.6.33.8-149.fc13.x86_64))After the update finished installing the new kernel, I restarted the system and Nvidia did not load. (I assume because Update manager removed the old nvidia? But I also assumed that a new version would be installed automatically?)I received the following Boot messages:
Code:
Entering non-interactive startup
Starting monitoring for VG vg_user1: 3 logical volume(s) in volume group "vg_user1" monitored
[code]....
I'm confused, if Update Manager removed kmod nvidia, then why does yum say it is installed? And why doesn't the new kernel update work with that version? Or should I install a driver version for that particular kernel? I've read while searching that I need to install a kmod-nvidia for that particual kernel version and that I should login to my previous kernel until that happens, is that the problem I'm having?
Why don't rpmfusion and fedoraproject release the kmod-nvidia and kernel updates at the same time to avoid problems such as this? Does anyone know how long does it usually take for rpmfusion to release the new kmod-nvidia driver for the latest kernel?
View 5 Replies
View Related
Jan 28, 2009
I have Fedora 10 installed. I've just made an update of my system. Things that were updated were a new kernel version with devel and also something with NVIDIA (which is my video card).
After restart of my system, compiz fusion no longer works.
I have a NVIDIA-Linux-x86-177.82-pkg1.run -file to manually install the NVIDIA-driver so the advanced features of Compiz can be utilized.
After install, the bootup screen tells me that loading the NVIDIA driver has failed. I also receive a WARNING-message.
View 14 Replies
View Related
Apr 22, 2010
I've manually installed the latest NVIDIA display drivers from the website (newer than the restricted driver package that came with 9.10). When there is a new Linux kernel, or a newer Ubuntu version, will I need to uninstall that driver before upgrading? Will having this driver cause any special installation issues during upgrade (such as the need to reinstall the driver after upgrading)? I am using 9.10 through Wubi.
View 1 Replies
View Related
Jul 6, 2010
I am running kernel 2.6.32-23-generic-pae and since updating nvidia drivers do not work. I go into hardware drivers and activate but I get dropping to low resolution desktop or VGA not supported.
View 2 Replies
View Related
