Fedora Installation :: 11 Boot - Error "Could Not Find Kernel Image: Linux" And The Boot: Prompt After That"
Jul 23, 2009
I have downloaded the i386-DVD.iso image and have burned it on a DVD using Nero Express 6, when it boots from the DVD, it give me an error message "Could not find kernel image: Linux" and the boot: prompt after that. I have burned another DVD using Infra Recorder with minimum write speed but with the same problem. I have Ubuntu already installed on the computer.
View 8 Replies
ADVERTISEMENT
Jan 26, 2009
I'm new to fedora and when I boot from a cd I get the message: could not find kernel image. I currently have windows xp and my motherboard is and ix38 quad gt if that helps.
View 2 Replies
View Related
Jan 28, 2010
basically put a new hard drive in my old computer and wanted to install fedora on it, downloaded fedora 12 dvd iso (3ish gb in size) have burnt it to a dvd disc, turned my laptop on and set it to boot from cd drive, restarted it, it reads the disc and displays the following message:
ISOLINUX 3.75 209-04-16 ETCD Copyright (C) 1994-2009 H.Peter Anvin et al
Could not find kernel image: Linux
boot:_
The uderscore is flashing and i can type stuff in but have no idea what to type in to find the kernel image, or why it cant find the kernel image.
View 2 Replies
View Related
Aug 25, 2010
It disappears too fast! I'm using the netinstall spin of the Fedora 13 x64 disk. As far as I know, I still need to tell it to load Anaconda from the network. Is that correct? Anaconda loads from the CD, but I would prefer to use the downloaded image. Should I just let Anaconda go through its paces then tell it where I downloaded the image to on my network?
The documentation is woefully inadequate when it comes to using the netinst spin (yes, I am already thinking about providing help on the install docs based upon my experiences).
View 9 Replies
View Related
Jan 5, 2010
's/ARCHTYPE=i386/ARCHTYPE=x86/'If your looking for a kernel image in /usr/src/linux/arch/i386/boot, your not likely to find one.
View 3 Replies
View Related
Sep 1, 2010
I had a a problem booting last night when my laptop battery came loose and caused a crash during boot.It ceased loading a daemon and I turned it off with the power switch, then I received the boot error,then i checked the linuxdrives directory and it was corrupt,I then, out of ignorance, ran wubi from within windows XP and said unistall believing that it would reinstall and fix itself.Thus you can see my green behaviour.I have been searching the threads and have tried many things but have had no success, I will suffer a great loss if I lose that load of Ubuntu as I have allot of work stored there, and in my Thunderbird accounts.
View 8 Replies
View Related
Sep 2, 2010
i used dual boot system (xp + ubuntu 10.04) and decided to replace them with jolicloud os and then it started In about 86% of jolicloud install it showed me error of hdd partition. I tried different versions of partion type, used also option to install on entire hdd - none of my tries actually worked (also with many hdd formating tries) so I was able to use only usb as live user for Jolicloud, and i burned ubuntu iso on disk - on boot up showed boot up error, i checked BIOS and everything seemed to be ok with boot order. So after many tries i took my old Gutsy Gibon 7.10 live cd. I first updated it with LTS version (8.04 Hardy Heron) and after that I updated it to 10.04 but it seemed to not finish when i saw some error in terminal and installer was exiting 13 minutes before finish then it had kernel panic - fuuuuck! After that i tried to download small versions of linux like Austrumi and puppy linux , but it showed me boot error or cd didnt even open install dialog without showing boot error.
View 1 Replies
View Related
Jul 5, 2009
I am currently running Fedora 10 XFCE on an Acer Aspire 1 (1.6ghz atom, 1.5gb ram, 8gb ssd). I am trying to install Fedora-11-i686-Live-XFCE via USB stick (Kingston 4gb) and am having no luck. I downloaded the .iso via bittorrent. If I use liveusb-creator: .iso passes checksum, installs boot image, installs syslinux, claims it's complete. When I try to boot, or simulate booting with qemu, I get the message "Could not find kernel image: linux" If I use
Code:
# livecd-iso-to-disk /home/jorge/downloads/Fedora-11-i686-Live-XFCE/Fedora-11-i686-Live-XFCE.iso /dev/sdb1
it says that the .iso passes checksum, installs live image, updates boot config file, and setup USB stick as a live image. Once again though, when I try to boot, or simulate booting with qemu, I get the same message "Could not find kernel image: linux"
View 2 Replies
View Related
Feb 17, 2010
Ive been trying to PXE boot a XEN kernel image in gzip format, and I was getting Invalid or corrupt kernel format error. Ive seen that other kernel images having a file type of Linux kernel x86 boot executable RO-rootFS are bootable. (both are bootable using grub anyhow).
Is there any way to convert the b/n the formats, or any other solution?
I was booting a Virtualbox instance, again I guess that shouldn't matter because pxelinux loads from tftp properly, but it doesn't even proceed to load the kernel. I think the issue here is with the image format itself rather than what it contains, or where it runs.
View 2 Replies
View Related
Sep 3, 2010
i am trying to install openSUSE from a usb pen. i have configured the BIOS to boot from Usb pen. i get "Could not find kernel image gfx boot".
View 5 Replies
View Related
Aug 7, 2010
I just built this computer with a bunch of old parts, and i put in a blank hard drive. There is no operating system on this computer yet. I put the Ubuntu Usb into the computer and made it boot from the Usb. Everything looked fine and good, until it said "boot:". It wanted me to type something in. So i clicked enter and it said "could not find kernel image: linux".
View 9 Replies
View Related
Nov 3, 2010
I wanted to Upgrade from Fedora 13 to 14 and downloaded the Upgrade Image using the Pre_Upgrade Installer. My system downloads the upgrade just fine but when it starts to perform the it asks for the location of the new Fedora 14 ISO and I have no idea where that is or what to enter as a possible location which I have no doubt is in the default area.
View 3 Replies
View Related
Apr 19, 2011
I have Ubuntu 10.10 installed on my laptop.Its a dual boot with XP, have been using ubuntu/xp for a while now..Till now i always used to remove older kernel images after ubuntu update, then update grub and do "sudo apt-get autoclean" never had any problem at all.i skipped the second step, i removed the old kernel image and did "Autoclean" on apt-get but forgot to update grub.
Now after i have reboot, when grub loads i can see only 2 "Memtest" lines in grub list and 1 "windows xp" line.the "Linux kernel generic" line is missing. I can boot in xp (have done just that to post this) but since there is no line in grub list to boot into Ubuntu, cant boot in Ubuntu.Is there any option, something i can do at "Grub" to boot into Ubuntu?
View 4 Replies
View Related
Jan 18, 2011
I had Ubuntu installed, i installed Debian and there was no dual boot. So i formated all the hard disk to install only Debian. It installed but at boot i get error: no such device and the grub rescue> prompt. i googled for a solution and nothing worked:
- i tryed reinstalling grub, not worked
- i did the windows cd fixmbr trick, not worked
- reinstalled debian with fixmbr the first step and nothing
- tryed deleting with dd the mbr, not worked
- reinstalled grub from debian rescue, not worked
what should i do? i can't access my computer? please tell me how should i fix it? the google guys will kill me because i put their servers on fire
View 14 Replies
View Related
Jan 21, 2010
I did the "yum update" today, the process was doing well but, the follow error appears:
Transaction Check Error:
installing package kernel-PAEdebug-2.6.31.12-174.2.3.fc12.i686 needs 9MB on the /boot filesystem
Look:
Code:
Transaction Summary
==================================
Install 10 Package(s)
Upgrade 33 Package(s)
Remove 1 Package(s)
[code]....
View 6 Replies
View Related
Jul 30, 2009
I'm trying to install F11 in my new laptop [URL] and I'm unfortunately about to give up, but I want to give this option. What I want to do is use the live cd (on a usb stick) to boot on a text-only session. Supposedly the way to do that is type "linux text" on the boot prompt but the problem is that I can't even get there. After booting I get the grub menu with two options: boot, and verify and boot. Hitting esc doesn't bring me to the boot prompt. I can get to the grub menu, but I'm not sure what to do from there. And I can edit the boot and kernel options, but I'm not sure whether that will allow me to log in a text-only session.
View 4 Replies
View Related
Nov 22, 2009
i could manage to install fedora 12 on my laptop (asus f6a) using the iommu=off option, but when i try to boot it i just reboot without even seeing the fedora logo, i just see the the prompt for 5 seconds and then it reboots.
View 3 Replies
View Related
Feb 10, 2010
I seem to have determined a few other things about my "only gets as far as a GRUB command line" problem:To recap, sda3 (GRUB hd0,2) is the main Linux partition; sda9 (GRUB hd0,8) is the boot partition.GRUB is 0.92.Installation was from an 8.04LTS live CD (at least, that's what the envelope says it is)/"/boot/grub" (i.e., "/grub" on sd9/hd0,8) contains a "menu.lst" file. I modified it (had to do a "sudo gedit" from a command line!) to (1) comment out the line that hides the boot menu, (2) change the timeout from 3 seconds to 90, and (3) add a menu line based on my succesful manual IPL of DOS.
It still boots to a GRUB command line. If I do a "configfile /grub/menu.lst," a boot menu comes up. DOS will successfully IPL, but Linux still gets a "no setup signature found," (ditto for "recovery mode"), which suggests either a bad kernel, or a kernel that's too big for the GRUB to handle.Why would it be finding its way to grub, but not finding the boot menu file?Why would the live CD come up just fine, yet the GRUB and kernel it installs fail?
View 9 Replies
View Related
Oct 20, 2010
I downloaded the Fedora live dvd iso file, burned it to a dvd. I was wondering if I forgot to do something or did I do something wrong. When I try to install from the dvd I get this error message, isoLinux: Disk error 80 , AX = 42A7 , drive 9F Boot Failed: press key to retry When I press a key to retry I get the same error. I also tried to install virtual pc and get not boot disk found.
View 3 Replies
View Related
May 14, 2010
After using slackpkg to update to -current on a new slack(32) install I was greeted with kernel panic "can't mount root fs" on reboot.
It was looking in the wrong place. I thought I answered yes and slackpkg would run lilo for me when it was done with the upgrade but perhaps I misunderstood.
I had my handy dandy USB boot stick so I set the bios and booted from USB. OK fine, I pointed to the correct location (hda1) and voila.
a 64bit kernel... The machine in question is a 2004 vintage celeron notebook
To my question: Is there a way I can point the loader to another kernel?
One last piece of the puzzle, the dvd drive is bad and I don't (yet) have a PXE server or even another linux box.
View 2 Replies
View Related
Nov 9, 2010
My laptop can't boot from cdrom becouse it is broken and it can't boot from USB becouse it has never been able. Ubuntu 8.10 now run in my laptop withgrub 1.I've just try the following trick.1) I put grub4dos in /boot2) I put iso image in /boot3) I add the follwing entrt in source.list
Code:
# =========== GRUB4GOS ===================================
title == Use grub4dos for the following entries: ==
[code]....
View 3 Replies
View Related
Aug 7, 2010
Had an issue after update in the nvidia module was not loading, after much messing about i found that system had installed kernel 2.6.32-24 but this had been added to grub even after running update-grub even though kernel was in /boot ?
It was booting into 2.6.31-17 fine
i removed 2.6.32-24 with apt-get remove and then reinstalled.
Now on reboot i can menu entry for 2.6.32-22/24 and 2.6.31-17 but none will load, just error 15 file not found?
View 4 Replies
View Related
Oct 4, 2009
building an install cd or dvd media that will automatically install the Linux software on a client pc. There is no network connectivity so the client can only be loaded with Linux from CD or DVD media. The crux of the matter is that I can not automatically install the Linux software on client WITHOUT typing linux ks=cdrom:/ks.cfg at the boot prompt.
I want to avoid any user prompts and just have the software install with the RPMS that I need for this client pc at the boot prompt. Actually, when the boot prompt commences, I would like the software install to start with no user intervention. I've tried several different methods in isolinux.cfg, but the OS always wants boot prompt for the cdrom. Can the boot prompt information be read automatically from the isolinux.cfg with out user intervention? I'm looking for the same behavior as a LIVE CD that kicks off with no boot prompts after a few seconds. Here's a copy of my isolinux.cfg
default linux
prompt 1
timeout 600
display boot.msg
F1 boot.msg
F2 options.msg
F3 general.msg
F4 param.msg
[Code]....
View 1 Replies
View Related
Jul 8, 2011
I already download Fedora 15 from website As ISO Image , How I can create Bootable CD Image? and it possible but it in USB as bootable
View 3 Replies
View Related
May 4, 2011
I switched over from Ubuntu because I realized Ubuntu sucks now (lol), but anyways... Now I'm trying to get Grub2 to boot up properly, but this "xputs" error pops up and drops me to the recovery prompt. I tried the grub-install dev/sda and all it did was recognize my Windows 7 OS (as Vista) and added it to the bootloader list and didn't fix the "xputs" issue.
I heard that doing a chroot is the most effective solution. Forgive me, but I don't know what "chroot" means or how effective it is. I can specify more information about where the OS is if needed. I have the boot flag set to the Debian OS at the hd(0,5) or sda5 I think, and Windows is at sda1 (I think). I just want to make sure I can fix this without damaging Windows, and I'll try to get more information.
Right now, I can only get into Windows or Debian with UBCD and Grub2 Super Disk and I know that sometimes Parted Magic could orderly mount the disks differently, so I don't know if it was sdaX or sdbX, but probably sdaX. I'll check again.
View 1 Replies
View Related
Aug 4, 2010
I ran the update through yum (replicated results twice) and whenever I boot to the new kernel it either freezes on the F logo or screen goes black right after f logo. No commands work whatsoever (tried em all). I can boot to an older kernel (2.6.33.3-85.fc13.x86_64). the ones that fail are: 2.6.33.6-147.fc13.x86_64 and 2.6.33.6-147.2.4.fc13.x86_64.
The Fedora error system gave me a bug report I submitted, here's what I got:
Package: kernel
Latest Crash:Tue 03 Aug 2010 09:46:33 PM
Command: not_applicable
Reason: BUG: unable to handle kernel NULL pointer dereference at 00000000000005b8
Bug Reports:Kernel oops report was uploaded
View 14 Replies
View Related
Nov 19, 2009
I am using Centos 5 with an old kernel. I want to build the latest version for atheros 5K wireless drivers. So i downloaded, and compiled with the ".config" which is already in /boot , and made it ready to run.
However, whenever i try to boot with new kernel, after choosing it from the grub menu, i got the following error. I tried many many .config files but the result was the same.
Here is the screen capture of the error;
I'm trying this process for a week without any success...
View 5 Replies
View Related
Feb 11, 2010
I use a pretty fresh installed RHEL 5.4, which should be very similar to Fedora. After the basic installation I installed xen and xen-kernel via yum with no errors. I can select the xen-kernel at boot time. But after booting the normal kernel shows up.
[root@noname boot]# uname -r
2.6.18-164.11.1.el5
My /boot/grub/menu.lst looks like:
default=1
timeout=5
splashimage=(hd0,0)/grub/splash.xpm.gz
[code]....
I can't see anything wrong and I did not change/try anything.
View 11 Replies
View Related
Jun 11, 2009
Yesterday, i just got my Fedora live DVD. When i tried to boot it from my CD/DVD ROM drive, it seems to hang when it's just about to finish loading. From one of the prevous threads, one of the members said that i had to have 2 partitions on my HD. Currently, i already have 2 partitions. Can someone give me advice on what to do??
View 3 Replies
View Related
Mar 27, 2011
I Installed Fedora 14 about 2 weeks ago and was just settling into using it more or les permanantly and had to turn of the power to do some maintenanace. When I rebooted I got the grub> prompt. As I have already shut down and rebooted several times over the last couple of weeks, I could not se why this happened, so I rebooted and stiull got the same problem. Things I have tried:
[code]...
I am currently using a 64 bit ASUS P75P55-M motherboard.
View 1 Replies
View Related
