when I first installed it on my IBM thinkpad, the eth0 was working correctly. I had someone try to install the network card for me, and something was changed to where now the wired connection is displaying "device not managed".
View 2 RepliesI use my T61 both wireless and in the dock, where I switch to the wired connection. After the latest round of updates, I seem to have lost the ability to switch to the wired network. When I turn the laptop on, I see it connect to the wireless network, but when I left click on the tray icon under Wired Network is says Device not managed. I have not made any changes to anything in the last couple weeks, besides some updates. How do I go about getting the wired network back in there?I tried to add eth0 back into System - Preferences - Network Connections, but whenever I try and add eth0, but it still says Device not managed.
View 2 Replies View RelatedYesterday I did an upgrade and today my box is unable to connect to the internet.
I have tried another cable, it didn't help.
Basically NetworkManager does not connect eth0 to the network, if I try to run ifup from the command line I get:
Code:
I can see in network configuration settings, that the device has been correctly detected and eth0 interface is correctly activated, yet when I try to uncheck the box manage by NetworkManager and start it manually, it tells me that the cable is disconnected... I've tried two different cables, different ports on my router - no help.
I use my T61 both wireless and in the dock, where I switch to the wired connection. After the latest round of updates, I seem to have lost the ability to switch to the wired network. When I turn the laptop on, I see it connect to the wireless network, but when I left click on the tray icon under Wired Network is says Device not managed.I have not made any changes to anything in the last couple weeks, besides some updates. How do I go about getting the wired network back in there?I tried to add eth0 back into System - Preferences - Network Connections, but whenever I try and add eth0, but it still says Device not managed.
View 2 Replies View RelatedCurrently my setup is a road runner cable modem connected to a desktop via a ethernet cable. The networkmanager lists "Broadcom BCM440-BO 100BaseTX" device not managed. I've turned off the power to both the cable modem and the computer. I then turned on the power to the cable modem and then the computer. If I try the firefox browser, it can not connect to the internet.
View 3 Replies View RelatedI'm getting rather fed up with this Network Manager applet on Ubuntu and its seemingly erratic behavior.I often use my laptop for things like dhcp server to do pxe boot on other machines for netboot installs and other stuff. Often I have to set static address on eth0 etc.I know how to set a static address for eth0 by editing /etc/network/interfaces and all that good stuff, but when I click on the Network Manager applet, it says 'Wired Network - not managed'.I may have deleted it for some reason, but why does it no longer appear, even though eth0 is working?I've also found in the past that changes to interfaces in the Network Manager, such as giving eth0 a static address, do not seem to stick?
View 6 Replies View RelatedI'm getting rather fed up with this Network Manager applet on Ubuntu and its seemingly erratic behaviour. I often use my laptop for things like dhcp server to do pxe boot on other machines for netboot installs and other stuff. Often I have to set static address on eth0 etc. I know how to set a static address for eth0 by editing /etc/network/interfaces and all that good stuff, but when I click on the Network Manager applet, it says 'Wired Network - not managed'. I may have deleted it for some reason, but why does it no longer appear, even though eth0 is working? I've also found in the past that changes to interfaces in the Network Manager, such as giving eth0 a static address, do not seem to stick? It seems the only thing this applet is useful for is connecting to a wireless network.....and only with dhcp !!
View 1 Replies View RelatedI've looked today on my logs /var/log/message and I find device eth0 entered promiscuous mode I don't remember putting eth0 in promiscuous mode I'm connected to the net thru a router how do i turn that off ?
View 1 Replies View RelatedMy network name is eth2 it was changed by some reason and now i got these errors... i installed, reinstalled, re re installed, tried to run the asistant but no luck :/
Code:
* Stopping the Firestarter firewall...
eth0: error fetching interface information: Device not found
eth0: error fetching interface information: Device not found
eth0: error fetching interface information: Device not found
[code]....
Seems everytime I upgrade wireless quites working.
Anyways, here's the info:-Acer Aspire One AOA150-1997
Quote:
kevin@ubuntu:~$ lspci
00:00.0 Host bridge: Intel Corporation Mobile 945GME Express Memory Controller Hub (rev 03)
00:02.0 VGA compatible controller: Intel Corporation Mobile 945GME Express Integrated Graphics Controller (rev 03)
00:02.1 Display controller: Intel Corporation Mobile 945GM/GMS/GME, 943/940GML Express Integrated Graphics Controller (rev 03)
[Code]...
I think that's all that would be needed to help diagnose the issue. I'm kinda new to linux, and this is primarily a music machine.
I have a problem with my internet connection this is the picture the device is Realtek RTL8187. i didn't know how can i manage this device to work so could you help me i don't have an internet connection in ubuntu right know and i really wanna move to ubntu my verison is 9.10
View 9 Replies View RelatedI installed Linux 6, configured the network during the install with a static IP and when I do an ifconfig command it doesn't show an IP Address. Can't get out to the Internet because I don't think I have an IP/Address. I restarted network, went into preferences-network connections and everything looks fine, ran system-config-network and everything looks fine. When I do an ipup ifcfg-eth0 and get the message "Connection activation failed: Device not managed by NetworkManager". Is there an option I failed to load at install or I need to install now?
View 2 Replies View RelatedI just finished installing Fedora 12 on a rack mount server. I was modifying the /etc/sysconfig/network-scripts/ifcfg-eth0 file to use a static IP address, but now nothing works. The device does not boot on start up or anything.Currently, ifcfg-eth0 looks like:
Quote:
DEVICE=eth0
ONBOOT=yes
BOOTPROTO=none[code].....
The eth0 device does not start on boot; the server does not get the IP address, is not reachable over the network, and will not connect to the internet....
When i wan to activate device in network configuration, it pop out with "CANNOT ACTIVATE NETWORK DEVICE ETH0". There is a sentence after this also : "rlt8129 device eth0 does not seem to be present, delaying initialization."
View 14 Replies View RelatedAfter the use of pppoeconf, the network manager does not recognise neither the wired nor the wireless connection anymore. (It nicely did it before that) I tried to replace the etc/network manager folder with that of a different machine. Still the same. What else can I do to reset Network Manager ?
View 1 Replies View RelatedI'm having trouble getting onto the internet with ubuntu 9.04. I have just moved house and have just got the internet set up here (typing this on windows laptop with wireless). My ubuntu desktop is plugged in to the network, but in the top right hand corner when I click on the network icon I get: "Wired network device not managed"
In my old house I had a static IP. Is this anything to do with it?
i install kernel rpm after i boot that kernel network not working kernel name : kernel-rt-trace-2.6.24.7-132.el5.centos.i686 [URL] error "Bringing up interface eth0: Device eth0 has different MAC address than expected, ignoring."
View 1 Replies View RelatedMy wireless connection has been giving me some problems, so I decided to try a wired connection directly to the router. However, when I try to do that, it doesn't work. When I click the network manager icon, it says that the wired device is not managed.
ifconfig gives this:
Link encap:Ethernet HWaddr 00:13:d3:dd:12:79
inet addr:192.168.1.100 Bcast:192.168.1.255 Mask:255.255.255.0
inet6 addr: fe80::213:d3ff:fedd:1279/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
[Code]...
I ran sudo dhclient to try release and renew my IP, in case that was the problem. It released and renewed successfully, but still didn't connect to the Internet.
I'm running Squeeze and I'm looking 3 days now for a solution in some weird problem. The NetworkManager Applet shows that there isn't connection although I am connected. The icon has this small "x" and when mouseover it says "No network conncection". Moreover when left clicking it, it says
"Wired Network Device not managed"
While I was looking for the solution a came across this post by an Ubuntu developer who says:network-manager-applet displays the connectivity state of network-manager's managed interfaces not every interface. So the title "network manager says disconnected but is connected and working" is actually misleading. The interface is connected and working but not from network-manager's point of view since it is not managing the interface. Additionally, in Lucid now network-manager applet displays nothing now for non-managed interfaces so is less misleading. You can check to see whether or not an interface is managed by network-manager by using the command line too nm-tool. You'll see "State: unmanaged" for unmanaged interfaces.
I have used the information available at wiki.debian.org/iwlagn to install firmware etc for my Intel Pro Wireless 4965 card.According to the network applet the connection is good, but it only seems to work when my ethernet cable is plugged in.I get no connection without the cable in, even though clicking on "edit connections" showshat ethernet is shown as "device not managed".With the cable plugged in I can get emails. Iceweasel will connect to the internet, but Epiphany will not.Without the cable I get no internet connection at all
View 9 Replies View RelatedI have to do a project on network security.For that i have to capture the packets from the device. I installed libpcap tool in ubuntu. If I give ifconfig -a it lists out eth0, wlan0, lo. I am able to connect to the internet via eth0. But when I give
#include <stdio.h>
#include <pcap.h>
int main()
{
char *dev, errbuf[PCAP_ERRBUF_SIZE];
[Code]...
It says device is null. I'm not able to run sniffex.c program also. All I want to do is to capture the live network level packets and analyse them.
While i am configuring network setting on backtrack4. i was running my backtrack on vmware workstation and NAT is bridged to physical mem like it was said on the tutorial that watched. i typed ifconfig eth0 up, and hit enter, as well as dhclient eth0 up, but resulted in different output. it says "no such device" is written and i would like to configre this problem.
View 2 Replies View RelatedI am trying to perform VM cloning using KVM in a centos 5.6 machines. I copy the memory contents of a running vm to an external state file and try to use that to start another VM in a different machine. While starting the cloned VM I provide a different mac address but once it resumes it has the old one . I tried changing the mac address in ifcfg-eth0 but I get the error: Device eth0 has a mac address xx:xx instead of configured xx:xx.Ignoring .
Is there some way to change the ip/mac of the cloned vm without the need to restart the VM ( Then the purpose of cloning will be defeated). Thanks a lot for the info.
i have 5.4 installed on a super-micro server motherboard (has two gigabit ether ports). when i boot while its initializing everything it gets to the "starting eth0" and just stays there?
right before it boots up and says press any key for options i press a key and choose "centos (2.6.18-164.el5)" and it boots up fine but when i choose "centos (2,6,18-164.el5xen)" the problem occurs. and that is the default boot option.
Installed Centos 5 on IBM T60P laptop. Intel 82573L Gigabit ethernet controller. Keep getting this erro message, "e1000 device eth0 does not seem to be present, delaying initialization."
View 3 Replies View Relatedsolve this error "3c501 device eth0 does not seem to be present, delaying initialization".
View 3 Replies View RelatedI have swapped out four known working, different bran network cards. Each one I get the same error as in the subject. If I boot to a Live CD such as CentOs 5.3 LiveCD both Nics are given an IP. This seems to only be happening with my CentOs 5.3 server install.I noticed the CentOS Live CD the Nics were reversed from eth0 to eth1 and eth1 to eth0.
At the moment as of the output of the commands, I am running two identical Nics, since the first one has always worked. I have previously used an rtl8139, 3com c3905-TX, onboard Rhine III based (now disabled) Here are steps I have done to try and figure this out:
Quote:
[root@centos ~]# lspci | grep -i eth
00:0a.0 Ethernet controller: VIA Technologies, Inc. VT6105/VT6106S [Rhine-III] (rev 86)
00:0e.0 Ethernet controller: VIA Technologies, Inc. VT6105/VT6106S [Rhine-III] (rev 86)
Quote:
[root@centos ~]# cat /var/log/dmesg | grep -i eth
eth0: VIA Rhine III at 0xee800000, 00:1b:11:bb:17:7d, IRQ 177.
eth0: MII PHY found at address 1, status 0x786d advertising 05e1 Link 45e1.
[code]....
I went through the system-config-network-tui. I copied /etc/sysconfig/network-scripts/ifcfg-eth1 to the ifcfg-eth0 and edited for sanity. and as stated earlier, have swapped out four different nics for eth0, and booted to two different LiveCD's. Both LiveCD's work fine.
I am running a CentOS 5.6 as a Virtual Machine on my Laptop. And, to connect to internet I am using a datacard (usb modem) device (Tata Photon +).
Now, internet is working well on my VM through interface ppp0
The problem is that when I start my interface eth0, internet (running through ppp0) stops.
Quote:
[root@kick ~]# ip route show
172.29.242.9 dev ppp0 proto kernel scope link src 14.99.211.189
default dev ppp0 scope link
[root@kick ~]# ip addr sh
1: lo: <LOOPBACK> mtu 16436 qdisc noop
[Code]....
im trying to setup eth0 with subdevice eth0.0 and eth0.99 to come up at boot
eth0 is dhcp clint
eth0:0 is static ip
eth0.99 is 802.1q vlan interface
/etc/network/interfaces
Code:
auto lo
[Code]....
I have installed Open SUSE in my DELL server which has 2 broadcom NIC cards, it showing both the NIC cards in Network configuration in YAST ,but it showing as not configured and not connected . Kernel device eth0,wlan0 are not present. In device manager also 2 Broadcom nic cards are detected.
View 4 Replies View Related