I have installed Open SUSE in my DELL server which has 2 broadcom NIC cards, it showing both the NIC cards in Network configuration in YAST ,but it showing as not configured and not connected . Kernel device eth0,wlan0 are not present. In device manager also 2 Broadcom nic cards are detected.
View 4 RepliesInstalled a TP-Link TG-3269 Gigabit card in a machine running OS 11.3 32 bit, when I go into Yast, Network Devices, Network to try configuring the card I get this errormsg: Unable to configure the network card because the kernel device (eth0, wlan0) is not present. This is mostly caused by missing firmware (for wlan devices). See dmesg output for details. Couldn't find any mention of the card in dmesg's output, (though the 8139 onboard card is in there) there is some stuff about pci host bridge but I don't know whether they would be relevant or not
The chip on the card says it's rtl8169sc but lspci lists it as being 00:07.0 Ethernet controller: Realtek Semiconductor Co., Ltd. Device 8369 (rev 10) Done some googling and there don't seem be any drivers for a Realtek 8639 and it returns no matches from a search on realtek's site, but there is a driver there for rtl8169sc chips, which I downloaded and installed, no errors when installing it Even after a reboot I still get the same error in Yast's Network Settings screen, lspci still lists it as 8369 and the device isn't listed at all if I run ifconfig
I'm new to this forum site and I was wondering how can I bridge a network between the eth0 and wlan0 connections?my eth0 NIC is a RealTek RTL8111B 10/100/1000 Ethernet Card (OnBoard) and my wlan0 NIC is a RealTek RTL8187B 802.11b/g WiFi USB Adapter Card.Are there any utilities, such as bridge-utils that I can use, except for Firestarter since Firestarter states that the eth0 connection is not established, or do I right-click on the network icon and select Edit Connections and go to Auto eth0 and under the IPv4 Address setting and select Shared to other computers and run a live connection there?The main reason is that I need an Internet connection for my Xbox 360, which is connected to my Linksys WRT54G 802.11b/g Wireless Router, that has DD-WRT firmware installed and 4 WiFi hotspots for any wireless device, such as my PSP, DS, DS Lite, Wii, Laptop(s), my brother's PC (needs a WiFi card), and my dad's PC (needs either a WiFi card or an Internet connection from my brother's computer to my dad's PC)
Here are my Computer Specs:
ECS nForce6m-a Motherboard
2GB DDR-800 PC6400 Memory
[code]....
I have installed Linux SuSE 10.3 on a PC (Lenovo Thinkstation A58). However, when I start the computer I get the following error message:
"No valid Host_ID or host-name found."
I then use YaST to set up the network. I get the following error message:
"Unable to configure the network card because the kernel device is not present."
The computer has Windows 7 installed and everything seems to work fine. The LED on the Ethernetplug is blinking when using Windows, but not when using Linux. I guess this means that there is no driver for the Ethernet card (Marvell Yukon 88E8057). I have not found any driver for the card and am considering buying a new one. Which PCI card works with SuSE Linux 10.3?
currently on an acer aspire 5532, and using mozilla and google chrome. webpages take about 10-12 seconds to load using the ethernet, wifi its about 2-3 seconds. using eth0 loading videos - broadcast yourself. in chrome, will sit at "resolving host" for about 10 seconds before bringing up the page. you would think eth0 is faster than wlan0, but for browsing the web its slower. i tested the speeds at speedtest.net - the global broadband speed test and both wlan0 and eth0 get the max speed my internet provides.i never downloaded drivers for the ethernet card or wifi, they worked so i didn't try to mess with them. but perhaps that is my problem?
code:
# lspci
00:00.0 host bridge: advanced micro devices [amd] rs780 host bridge
[code]....
I recently setup a new SUSE box for the purposes of acting as an ftp/sftp server. It's currently setup to run ProFTPD 1.3.3.rc3 and mod_sftp/0.9.7. The server has two internal network interfaces eth0 and eth1. eth0 is purely for internal use to accept ftp and ssh. eth1 is outward facing and receives connections from the WAN via SFTP over port 22. The problem I am facing is that after half hour to an hour eth1 stops accepting connections whenever there is no SSH connection present on eth0. I can't figure out why this is happening.
ProFTPD is setup as follows: SocketBindTight directive is on, default server and port are commented out.
[code]...
When the external interface is unreachable the proftpd and proftpd-sftp logs show no record of any connection attempt. I have noticed however if I leave eth0 down eth1 stays contactable without problem. Can anyone give me some pointers on what I can check to find out why this may be happening.
I've had 11.4/KDE working pretty well on dual boot Asus G73SW for a few weeks now. Only issues were the FN-* functions that control keyboard lights and whatnot but no biggie since the essential worked.The last couple of days the update notification was indicating 1,201 updates to be made. Yeah it seemed extreme but I googled around and checked the forums and there was nothing related. I figured I might be missing some packages since I installed from the live KDE CD (still 1202 updates!!!???). So I updated. Big mistake!!!!! Ever since NetworkManager cannot connect to the internet, be it wired or wireless.
Initially it could not even see my home network but it picked it up after I removed the plasmoid from the panel and reinstalled it. However it doesn't respond when I click the network icon and still no connection.I managed to get eth0 working with ifup but not wifi. The last part of network manager log file is quoted below. I can send the whole thing to whoever is interested. I can't make sense of it but maybe someone on the forums can.
Code:
Jul 13 11:09:08 linux-yy10 NetworkManager[1649]: <info> NetworkManager (version 0.8.9997) is starting...
[code]....
Installed Centos 5 on IBM T60P laptop. Intel 82573L Gigabit ethernet controller. Keep getting this erro message, "e1000 device eth0 does not seem to be present, delaying initialization."
View 3 Replies View Relatedsolve this error "3c501 device eth0 does not seem to be present, delaying initialization".
View 3 Replies View RelatedI have swapped out four known working, different bran network cards. Each one I get the same error as in the subject. If I boot to a Live CD such as CentOs 5.3 LiveCD both Nics are given an IP. This seems to only be happening with my CentOs 5.3 server install.I noticed the CentOS Live CD the Nics were reversed from eth0 to eth1 and eth1 to eth0.
At the moment as of the output of the commands, I am running two identical Nics, since the first one has always worked. I have previously used an rtl8139, 3com c3905-TX, onboard Rhine III based (now disabled) Here are steps I have done to try and figure this out:
Quote:
[root@centos ~]# lspci | grep -i eth
00:0a.0 Ethernet controller: VIA Technologies, Inc. VT6105/VT6106S [Rhine-III] (rev 86)
00:0e.0 Ethernet controller: VIA Technologies, Inc. VT6105/VT6106S [Rhine-III] (rev 86)
Quote:
[root@centos ~]# cat /var/log/dmesg | grep -i eth
eth0: VIA Rhine III at 0xee800000, 00:1b:11:bb:17:7d, IRQ 177.
eth0: MII PHY found at address 1, status 0x786d advertising 05e1 Link 45e1.
[code]....
I went through the system-config-network-tui. I copied /etc/sysconfig/network-scripts/ifcfg-eth1 to the ifcfg-eth0 and edited for sanity. and as stated earlier, have swapped out four different nics for eth0, and booted to two different LiveCD's. Both LiveCD's work fine.
I am very new to linux.I have a network camera which only has an Ethernet port but no WiFi. Sadly no Ethernet port is available close to the camera.
Therefore I now bought a raspberry pi and installed raspbian to create a bridge into the wireless network, for connecting the camera to the internet.I now played around with the interface- and bridge configuration but I have problems with it.This is how my interfaces file looks like:
(The WiFi is secured with WPA2 Enterprise)
Code: Select all# interfaces(5) file used by ifup(8) and ifdown(8)
# Please note that this file is written to be used with dhcpcd
# For static IP, consult /etc/dhcpcd.conf and 'man dhcpcd.conf'
# Include files from /etc/network/interfaces.d:
source-directory /etc/network/interfaces.d
[code]....
The WiFi is connection works fine and I am in the internet using the WiFi.But I am wondering about eth0. The network parameters I specified are not the same as the parameters ifconfig tells me.Ip, Broadcast, Mask, nothing is as specified.It would be nice to give the camera a static IP that I can access it always with the same IP from the RaspberryPi.The Raspberry Pi itself gets always a new IP from the WiFi network. How do I get the camera into the internet using the existing connection of the Pi?
I just installed Fedora 13 on a new Dell XPS desktop and some of the networking files are not created/missing. The computer has Broadcom Gigabit wired card and Asus PCE-N13 wireless card. When I type lspci, I see that Network conroller: RaLink RT2860 and Ethernet controller: Broadcom BCM57780 Gigabit Ethernet. So, somehow they are being detected by the OS, but I am not sure if the drivers are installed or why some of the network files are missng.
View 1 Replies View Relatedi install kernel rpm after i boot that kernel network not working kernel name : kernel-rt-trace-2.6.24.7-132.el5.centos.i686 [URL] error "Bringing up interface eth0: Device eth0 has different MAC address than expected, ignoring."
View 1 Replies View RelatedThe computer and system in question is the laptop from my description and openSUSE 11.3 with a different kernel from this repository :[URL]..free to move this thread if it should reside in the beta/prerelease forums section. The IMHO relevant information about my hardware and system is shown below.
The kernel I'm using :
Code:
grzes@opensuse:~> Linux opensuse.local 2.6.37.2-1-desktop #1 SMP PREEMPT 2011-02-25 19:59:41 +0100 i686 i686 i386 GNU/Linux
The hardware and drivers I'm using :
Code:
02:00.0 Network controller [0280]: Atheros Communications Inc. AR9285 Wireless Network Adapter (PCI-Express) [168c:002b] (rev 01)
[Code]...
Having trouble with wireless and FC11, eth0 is ok. When I try to activate wlan0 through system-config-network 1.5.97, I get msg: Error for wireless request "Set Mode" (8B06) : SET failed on device wlan0 ; Invalid argument. Determining IP information for wlan0... failed. This is a compaq laptop.
<uname -r>
2.6.29.6-213.fc11.i686.PAE #1 SMP Tue Jul 7 20:59:29 EDT 2009 i686 athlon i386 GNU/Linux
<lspci>
The wireless card is Atheros Communications Inc. AR242x 802.11abg Wireless PCI Express Adapter
(rev 01)
When i wan to activate device in network configuration, it pop out with "CANNOT ACTIVATE NETWORK DEVICE ETH0". There is a sentence after this also : "rlt8129 device eth0 does not seem to be present, delaying initialization."
View 14 Replies View RelatedI have setup a dual boot machine which has OS of Windows Vista (32 Bit) / RHEL 5. The LAN Card details are - Atheros L2 Fast Ethernet 10/100 Base T - Controller. The said Network Card works fine with the ADSL Connection in Windows OS, but does not seem to initialise in Linux. When I run "ifconfig" in terminal window it gives away the prompt - "eth0 no such device exists".Although it shoes the loopback adapter (lo) device working fine. I forgot to mention over here, I have just started with Linux. So, I request "the" Linux Gurus to help me out with this one.
View 1 Replies View RelatedI tried to install suse 11.4 on the new gnome desktop 3. everything seems to work except the network manager. Is not present in the bar and I can not restore it. tried to reinstall network manager but to no avail.Does anyone know how I could solve this problem
View 1 Replies View RelatedI just switched from Fedora 13 to openSUSE 11.3 on my laptop and so far love it...well...not quite. I'm having some major network issues. As in...no networks.
I installed everything and booted up for the first time. Everything worked great, I had wireless through wlan0 and could connect directly to my home router via eth0 with no problems. Installed a few applications and ran into some problems with hibernating/suspend modes. I rebooted and like magic, NetworkManager said networking was diabled. My WiFi light was off. Network switch on the computer didn't do anything.
I thought alright, I'll connect my ethernet cord and can go from there....problem is that won't work either. I tried searching for drivers online on my desktop, found some and transferred them via USB with no luck. They won't install. I have no idea why, or whats going on but I really need my laptop for school on Monday so it would be AWESOME to have it working by then.
Here is what I have:
Intel 5150 WiFi card
Dell Studio XPS M1640 laptop
OpenSUSE 11.3
On a new Dell Lattitude e6400, I have installed both arch and Ubuntu. Ubuntu recognized wifi and ethernet right away and connected and is working fine, but in arch, I am having more problems then I usually do when using arch. From the output of lspci the ethernet is a intel device 1502, I have researched this and found it to need the e1000e module as its driver. I modprobed this module sucessfully, but no ethernet. With wlan, i have found that the card is a DW1501 Wireless-N WLAN Half-Mini Card that has a broadcom 4727 chip in it. I downloaded the windows driver for this chip and isntalled it with ndiswrapper but this did not help. What I think is the root of the problem is the error message that restarting networking creates.
Quote:
Dell only supplies drivers for ubuntu, but it should still be possible to get this to work. I have tried booting various live distros that I had drives for and I found that the parted magic boot disk saw the ethernet port and was able to connect to ethernet, and that the ubuntu live disk was able to connect to both wifi and ethernet. Somehow they must be seeing the prescense of the hardware in a way that I have not tried with arch. Please help, I really need to get this computer workign with arch.
Is there a way to get conky to show only eth0 or wlan0? My configuration only shows the wireless bit when wifi is switched on but shows eth0 all the time.
Temperature: I have nvidia card with drivers from rpm fusion, can conky give me the temperature of the card and the cpu?
I have a wired connection going to my router, which is encrypted with WPA2-PSK. That works fine. I hooked up a WUSB54G v4 (Linksys USB Wireless Adapter), and used ndiswrapper to install the drivers from Vista to make it compatible with WPA2. Also configured the /etc/network/interfaces with the wpasupplicant lingo to make it all work. So if I do that, my eth0 will not work anymore. Also on a side note my network manager stops with displaying in the top panel. Not a problem I can run /etc/init.d/networking (re)start and dhclient eth0 (wlan0) and all the other commands that are necessary to make it work.
Back to the problem, so I hook up wlan0 with the settings and eth0 stops working. I want to use the wlan0 solely for the purpose of my media server. The eth0 is there for my internet and that is it .
How can I keep 'em separated?
I'm running Ubuntu Server 10.10 on a 64 bit laptop (also have GNOME installed just for convenience), and have a website up using apache2. I am wondering if it is possible to configure both eth0 and wlan0 to the same local static IP address? I would like to walk around my house and do stuff when I want and still have the website accessible, but also be able to jack my laptop back into the router when I am away, just for peace of mind.
Is this possible? If it is, do I need to do some configuring in apache2 to tell it to use another device? Is this even a smart way to get what I want done?
In an attempt to set up wireless so I could connect to the university network, which I think I probably should have just downloaded network manager or something but I didn't, I tried to put things in /etc/conf.d/net and some other places and I am afraid I'm not sure exactly what (and I have learned my lesson! I will pay attention to what I am doing so I can undo it next time I mess around with stuff!)
Anyway, the long and the short of it is now, when the computer is starting up and its doing the init stuff net.lo doesn't start. Later try and start net.lo or net.eth0 you get told "not enough arguments"
My network name is eth2 it was changed by some reason and now i got these errors... i installed, reinstalled, re re installed, tried to run the asistant but no luck :/
Code:
* Stopping the Firestarter firewall...
eth0: error fetching interface information: Device not found
eth0: error fetching interface information: Device not found
eth0: error fetching interface information: Device not found
[code]....
when I try logging on to my OpenSuse 11.1 Server.I get this error:rdpx11 channel not present
View 4 Replies View RelatedWhen I type ifconfig,
I see wlan0 and eth0. I want to somehow bind these two together into one device.
How would I go about doing this?
I'm running Linux Mint 10 . I have a wireless PCMCIA card (Linksys WPC 11 ver.3) that I've put into master mode, and I'm trying to set up my laptop as a wireless hotspot. I am very confident that I want to do this and have no interest in using a wireless router....I say that because that topic inevitably comes up with posts like this. The problem I'm having is I don't understand how to get wlan0 and eth0 to "talk" to each other...That is, I don't know how to set it up so that traffic from wlan0 goes through eth0, so that devices that connect to my hotspot can access the internet.I've seen a few guides about this, but they were either much broader in scope (i.e. much more complex), or for other distributions, etc, and it's too much for me to follow as a linux .
View 6 Replies View Relatedjust wondering if I could get a hand with bridging my eth0 and wlan0 connection. I'm using Ubuntu 11.04 if that helps at all.
View 1 Replies View RelatedI would like to pose is very specific to a system I'm assembling. I have ask for assistance from other forums and people, however the answers receive were too vague to implement.
As for my background, I am a network user able to write TCP Linux client/server applications quite easily. At a Linux system level I do not understand the necessary combination of applications and services to affect the following;
Network components;
- WiFi access point/router with four ethernet ports
- Laptop (user computer) cabled directly into the access point via a physical cable
- Second computer running Ubuntu 10.04, with one WiFi (wlan0) and one ethernet (eth0) interface. Eth0 is configured as a DHCP server with the following;
IPaddress 192.168.252.1
broadcast 255.255.255.0
Eth0 is physically connected to an IP camera via a Cross-over cable. The camera is configured as a DHCP client. This connection works perfectly from the Linux box with a KVM attached.
Wlan0 is connected wirelessly to the access point and the Laptop can access the Linux box and vice versa.
My objective is to have the
- Laptop via the access point/router connect directly to the IP camera on the Linux box via the wireless link.
- I would prefer not to make any configuration or routing changes/entries on the access point/router.
The type of response I'm looking for;
- is this possible at a macro level
- what facilities/server are required on the Linux box (I would like all configuration applied to this computer only)
- what commands need to be executed and in what order. If possible a brief explanation of why the command is needed and where it fits in the grand scheme of the solution.
This is probably a gigantic request outside what the forum usual activity.