Ubuntu :: Eth0 Doesn't Exists For Firestarter - Eth0: Error Fetching Interface Information: Device Not Found
May 5, 2010
My network name is eth2 it was changed by some reason and now i got these errors... i installed, reinstalled, re re installed, tried to run the asistant but no luck :/
Code:
* Stopping the Firestarter firewall...
eth0: error fetching interface information: Device not found
eth0: error fetching interface information: Device not found
eth0: error fetching interface information: Device not found
[code]....
View 1 Replies
ADVERTISEMENT
Nov 15, 2009
I have 2 network cards eth0 and eth1, for eth0 i set a manual MACADDR in network scripts. Ok so every time i boot, if the cable is plugged in, my eth0 fails to mount or i don't know.. i get this after bood when i type ifoncifg eth0 (eth0: error fetching interface information:Device not found). So i have to unplug the cable when i boot, then plug it in and do a service network restart.
View 5 Replies
View Related
Dec 26, 2010
i install kernel rpm after i boot that kernel network not working kernel name : kernel-rt-trace-2.6.24.7-132.el5.centos.i686 [URL] error "Bringing up interface eth0: Device eth0 has different MAC address than expected, ignoring."
View 1 Replies
View Related
Apr 19, 2010
I have setup a dual boot machine which has OS of Windows Vista (32 Bit) / RHEL 5. The LAN Card details are - Atheros L2 Fast Ethernet 10/100 Base T - Controller. The said Network Card works fine with the ADSL Connection in Windows OS, but does not seem to initialise in Linux. When I run "ifconfig" in terminal window it gives away the prompt - "eth0 no such device exists".Although it shoes the loopback adapter (lo) device working fine. I forgot to mention over here, I have just started with Linux. So, I request "the" Linux Gurus to help me out with this one.
View 1 Replies
View Related
Mar 8, 2010
If I uncheck and recheck "Enable Networking" in the Network Manager Applet 0.7.996 I would expect the wired network to disconnect (which it does) and reconnect (which it does NOT). So I tried sudo ifdown eth0 and got
Quote:
Ignoring unknown interface eth0=eth0.
ifconfig tells me
Quote:
eth0 Link encap:Ethernet HWaddr 00:25:64:e8:18:2c
inet addr:192.168.0.112 Bcast:192.168.0.255 Mask:255.255.255.0
inet6 addr: fe80::225:64ff:fee8:182c/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
[code]....
so I am at a loss. How do I stop and restart the network interface short of rebooting the machine?
View 9 Replies
View Related
Dec 18, 2010
I'm running a dual boot Ubuntu 10.04/Backtrack 4 (Ubuntu 8.10) system. I can get internet in the BT4 side but not in the Lucid side. In Lucid I can ping my router, and the network manager says I'm good to go, but I can't get to any web sites. It all started when I tried to put my laptop on another network by mimicking the settings of a computer I had just unplugged from the network. MAC address and all.
ifconfig eth0:
Code:
eth0 Link encap:Ethernet HWaddr 00:1f:16:ba:4c:8c
inet addr:10.136.9.147 Bcast:10.136.9.159 Mask:255.255.255.240
inet6 addr: fe80::21f:16ff:feba:4c8c/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
[code]....
View 3 Replies
View Related
Aug 6, 2011
I have a Dell Vostro 3500, which has a Broadcom wifi card. It requires non free drivers. So far it has been working well. However, after updating the kernel (via yum update), my wifi card (it used to be eth1) is totally gone: $ ifconfig eth1 eth1: error fetching interface information: Device not found The wireless indicator does not light up either. The kernel version is
[code]...
View 3 Replies
View Related
Jul 19, 2011
I booted an OS from a live CD. The OS boots successfully but eth0 fails to start. I checked lspci, it outputs these Ethernet card details:
(Broadcom Netextreme II BCM5716 GBabyte ethernet)
ifconfig -a returns only the loopback interfaces lo and sit0. The output of dmesg | grep -I 'eth' is:
"Netfront : initializing network ethernet driver"
When I run service network restart I get:
"Obtaining IP for lo [FAILED]
WARNING: Deprecated config gile /etc/modprobe.conf , all config files belong into /etc/modprobe.d/
Device eth0 does not seem to be present, delaying initialization [FAILED]"
The output of MII-tool -v is:
No MII interface found.
I was also able to find the kernel module bnx2.ko. I did insmod and lsmod lists it.
View 1 Replies
View Related
Jul 13, 2009
On my machine (Desktop PC) I have 2 network card : wireless (rt61 802.11) and a wired card (BCM44). When I install debian 5.
The wired card is detected and logical name eth0 is assigned, while wireless is not assigned I install firmeware* software to configure the card. It is done in some way ( I used mnetwork from mepis, it works fine).
Now the problem: eth0 disapears, and no eth0 inteface found? ifconfig gives just wlan0.
Question: Why there is no eth0, it was before configuration of wlan0 ?
How to active again eth0, or ho to create the logical eth0?
View 5 Replies
View Related
May 14, 2011
I am trying to connect my fresh new Ubuntu 10.10 to my router. However I am having a bit of difficulty. This is what I have done so far:
Code:
lspci
My devise is a Broadcom Corporation BCM4311 802.11b/g WLAN (rev 02). Then:
Code:
sudo ifconfig eth0 up
sudo iwlist eth0 scan
I get eth0 Interface doesn't support scanning.
View 10 Replies
View Related
Apr 22, 2011
im trying to setup eth0 with subdevice eth0.0 and eth0.99 to come up at boot
eth0 is dhcp clint
eth0:0 is static ip
eth0.99 is 802.1q vlan interface
/etc/network/interfaces
Code:
auto lo
[Code]....
View 1 Replies
View Related
Jan 14, 2010
solve this error "3c501 device eth0 does not seem to be present, delaying initialization".
View 3 Replies
View Related
Nov 18, 2010
I've looked today on my logs /var/log/message and I find device eth0 entered promiscuous mode I don't remember putting eth0 in promiscuous mode I'm connected to the net thru a router how do i turn that off ?
View 1 Replies
View Related
Jul 26, 2011
I am trying to run Firestarter firewall but keep getting the message ETH0 is not ready. This problem has been highlighted by others but is there a simple way of sorting this out, answers in other forums are wide and varied. but it's not clear if they have been successful.
View 7 Replies
View Related
Apr 14, 2011
I found multiple sites explaining how to add IPs to a network interface as virtual interface like eth0:0. However I can add IPs to an interface as well using the ip command: ip a a 192.168.2.2/24 dev eth0 What I want to know is how I can make this persistent on rhel/centos.
View 2 Replies
View Related
Feb 12, 2010
i want to know about eth0..that where information is saved from eth0?in which file? and how to take input from that file? what will be the script?
View 5 Replies
View Related
Aug 19, 2009
5.10 Breezy configured as machine controller. Works great eth0 is a fixed IP to communicate with controller comms board. Not easy at all to alter - the comms board is hard coded to listen on eth0 for commands.
I can use eth1 as the default gateway and ping google.com, etc. But when I now attempt to communicate with the controller with netcat, e.g.
Code: echo !HH | nc 192.168.1.6 80
I obviously never get an answer since the request is passed via eth1. Using the -g option with netcat doesn't work either. I had a look at iptables but it doesn't seem to be able to do what I want. How I can still use eth0 as my communication port to the controller whilst eth1 is the default gateway?
View 17 Replies
View Related
Jul 1, 2010
I have two servers on a vlan at my datacentre/colocation and previously both servers had public IPs on their eth0 interfaces. The servers are HP ProLiant DL360s - one is a G4 and one is a G5 The newer G5 is now the LAMP server and the G4 has been retired and I want to repurpose it as an iSCSI target using openfiler freenas or similar.
My G5 has public/static IPs lashed to the eth0 physical interface and the eth1 is not configured to do anything yet. The G4 will have both interfaces available - perhaps one for ssh access from one of my static public IPs and the other to be a private IP on the local vlan. Here is what I am trying to get my head around...
The G5
eth0 - Public IP - full LAMP services on two or three virtual interfaces
eth1 - Private IP 192.168.0.1
The G4
eth0 - Public IP for ssh
eth1 - Private IP 192.168.0.2
Because my traffic between eth1 on these boxes is via private IPs on the local private vlan it doesn't add to my quota for bandwidth. How do I go about configuring the routing and gateways and other aspects of this so that I can run a private IP space network between the eth1s and still serve the outside world from the eth0s...
I am afraid that if I assign the private IPs to the eth1 interfaces the routing may either not work or interfere with the access to the production internet facing interfaces (eth0s).
View 10 Replies
View Related
Mar 3, 2010
I got two IP's in my dedicated server. Both are external IP's. I would like to make connections using 2nd IP address under eth0:0 interface. For example: when using "lynx whatismyip.com" should display my 2nd IP. How to do this using iptables ?
View 1 Replies
View Related
Jun 29, 2010
Eth0 and Eth1 is bonded and works fine but when i reboot the OS eth0 and eth1 cant be up when i run command "ifup bond0", it gives me following message.
OS information:
Network Card :
I am using above card , it works perfectly fine and I have bonded but when I reboot , eth0 and eth1 looses this driver and also the RPMS I have installed , they are gone too.
View 7 Replies
View Related
Oct 7, 2009
I have been running into network issues lately with my CentOS 5 (installed on AMD Athlon X2 - 64 bit machine about 2 years ago). It was able to connect to the network fine until yesterday when I installed more memory into the machine restarted it.
Upon restart, the boot up was paused at 'Determining IP information for eth0' step for a while and booted with out connecting to the network. I tried restarting the network (/sbin/service network restart), but this is the error message I continuously get: Determining IP information for eth0...PING xxx.1.226.1 (xxx.1.226.1) from xxx.1.226.83 eth0: 56(84) bytes of data
[Code]...
View 2 Replies
View Related
Apr 1, 2010
I've seen this pop up a few times on the forum but my setup is slightly different. I have a PC with an ASUS P5N32-SLI Premium motherboard. I've just installed CentOS 5.1. Yes, I know this is ancient, but this is what they're developing on at work. I'm trying to get connected either via ethernet or wireless and neither one works. When I boot the computer to Window XP it does connect on ethernet. Ethernet should be easy so I'm concentrating on that. But I get "Determining IP information for eth0... failed." after a 'service network start'.Here is some other information that was asked on similar threads:
> uname -rmi
2.6.18-53.el5 x86_64 x86_64
> grep eth0 /etc/modprobe.conf
[code]....
View 4 Replies
View Related
Mar 16, 2011
I have already tried reloading the drivers, restarting the interface (which is missing) and every other solution I found on this forum (well... not exactly all of them but many of them) uname -a gives Linux hostname 2.6.35-27-generic #48-Ubuntu SMP Tue Feb 22 20:25:46 UTC 2011 x86_64 GNU/Linux
[Code]....
View 3 Replies
View Related
Aug 13, 2010
I'm having the same Harker2010 's problem.Running 10.04 LTS on a Dell latitude D-820, and switching between lan and wifi worked OK until last upgrade.Harker2010's screenshots are also valid for my problem. I've tried everything I see on this post but the problem still there.
View 1 Replies
View Related
Mar 2, 2011
I'm not sure how long ago this happened but eth0 seems to have vanished from my computer. wlan0 works fine and when I plug into the switch there is carrier detect.
Code:
21:35:43 ~:$ ifconfig eth0 up eth0: ERROR while getting interface flags: No such device
21:55:49 ~:$ lspci 05:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8101E/RTL8102E PCI Express Fast Ethernet controller (rev 05) 07:00.0 Network controller: Intel Corporation Ultimate N WiFi Link 5300 After that i have no idea where to search for problems next, any ideas would be greatly appriciated (can't spell) ubuntu 10.10
View 11 Replies
View Related
Jun 7, 2010
I have a question regarding the configuration of Network Connection. My wired connection is fine right now and when I check the network connection applet, it display active information of eth0. However, when I click the Configure button, the Network Connection window appears but there's nothing in the Wired panel. Should there be a eth0 in that panel? I remember I had one before, but after I messed with some configuration of VPN, my network became unstable and I remove the Network Manager to try to solve the problem. Since then, there's nothing in my Network Connection window, though I can still connect to my router with eth0. Now even after I reinstalled the Network Manager, I still don't get anything.
View 7 Replies
View Related
Jan 31, 2010
I have two network interfaces on my computer but only one of them is connected to an Ethernet cable. Until now on every Fedora release, the activated primary interface has been named as eth0 and everything has always worked well without any problem. Recently I switched to Fedora Core 12 and surprisingly I observed that for the first time, my primary interface has been considered by the system to be eth1 instead of eth0. I tried to replace the content of ifcfg-eth0 by ifcfg-eth1, yet system gave me an error that there was MAC address mismatching. I conserved their MAC addresses in their files and just replaced other connection parameters ( such as IP ADDR, NETWORK, NETMASK, etc.) but it did't work. When I do "server network restart", the command blocks.
As I try to install oracle on this system, regarding the fact that oracle requires static network configuration on the primary network interface, I don't know how to proceed in order to set eth0 as my primary interface (or rather set the current eth1 to eth0 because it is actually eth1 that refers to my activated primary network card).Just one more time, I would like to remark, that with previous versions of the Fedora Core, on the same computer (with the very same two network cards) I never had problem and I had installed oracle on the system with success, having the statically configured eth0 correctly detected by the system.
View 2 Replies
View Related
Nov 6, 2010
I'm using CENTOS 5.5 and I want to connect to internet using 2 pppoe accounts same ISP and i have a sigle NIC eth0.I used adsl-setup to create pppoe connections, 1 is ppp0 and second is ppp1. When i use /sbin/ifup ppp0 it works, i can use the internet, but when i try to use /sbin/ifup ppp1 while ppp0 is connected, nothing happens, i did ifconfig and there is only ppp0 showing.I'm a BIG NEWBIE of linux, i need to know step by step how to make this work, i heard something about a virtual network... but nothing clear.
View 5 Replies
View Related
Jul 19, 2010
I have followed th given site for HA configuration in my virtualbox but heartbeat is not assigning virtual IP for interface eth0 [URL]...
View 1 Replies
View Related
Nov 6, 2010
I'm using CENTOS 5.5 and I want to connect to internet using 2 pppoe accounts same ISP and i have a sigle NIC eth0.I used adsl-setup to create pppoe connections, 1 is ppp0 and second is ppp1. When i use /sbin/ifup ppp0 it works, i can use the internet, but when i try to use /sbin/ifup ppp1 while ppp0 is connected, nothing happens, i did ifconfig and there is only ppp0 showing.I'm a BIG NEWBIE of linux, i need to know step by step how to make this work, i heard something about a virtual network... but nothing clear.
View 7 Replies
View Related
