I installed Debian lenny 5.04 today through netinstall. After install it refuses to boot and says, "No bootable device found - "insert and press any key".
Motherboard : Intel DP35DP
Processor : Intel core 2 duo
RAM: 2 GB
NVIDIA 8500GT 512mb
I have googled it around and it seems to be something to do with BIOS. I am sure harddisk is not fried. Because I installed Ubuntu and it works
Today I installed Fedora (I need it for school), but not everything seems to work fine Before installing Fedora on my Macbook I had a triple booting machine: Mac OSX snow leopard, Windows 7 and Ubuntu. (using rEFIt) All of them where working. Since I installed Fedora on the 4th partition I can only boot Mac OSX. When selecting one of the other OS's it says: "no bootable device insert boot disk and press any key"
View 5 Replies View RelatedReboot and select proper boot device or insert boot media in selected boot device and press a key. I got this error after: Reducing my Windows 7 partition by about 100gb. Creating a new partition (100gb) and copying my Ubuntu partition (10gb) to the new partition. After it was copied, and pasted, the original partition was deleted. I now had two partitions a new 100gb Ubuntu partition and a 600gb (or so) Windows 7 partition.
All of this was done using a bootable USB with Ubuntu 10.10 and GParted partition editor. Now when I boot I get the "Reboot and select proper boot device or insert boot media in selected boot device and press a key." error.
I am trying to install fedora 14 from live CD (USB boot) in my system which already has Windows 7. The installation goes fine however when I reboot the system I get 'No bootble device found' error. install fedora on the entire hard disk which I cannot do right now.
In Bios there are 'Native' and 'Legacy' options for 'ATA/IDE Mode' and if I select 'Native', 'Configure SATA as' option is enabled with options 'AHCI' and 'IDE'. I reinstalled fedora with all possible configuration, Legacy mode, Native + AHCI, Native + IDE but got the same error when booting. I have also tried options; MBR on /dev/sda and first boot record on /dev/sda5.
fdisk -l :
Device Boot Start End Blocks Id System
/dev/sda1 2048 78782463 39390208 5 Extended
/dev/sda2 78782760 211897349 66557295 7 HPFS/NTFS
[Code]....
I installed openSUSE 11.3 on my iMac along with "Mac Snow Leopard, Windows 7" to make it a "Triple Boot". But after installing the "GRUB/LILO", it does not chain with the boot loader "REFIT" that I use. Each time I try to boot into "Windows/openSUSE", it shows a message: no boot device found, insert boot disc". So why isn't the "GRUB/LILO" working?
View 4 Replies View RelatedI bought a t770.uk HP desktop PC, which came without a Hard drive as the pervious owner had removed it for security reasons. A week later I got a hold of a brand new - out of an anti-static sealed bag - compatible Western Digital Caviar SE 80GB SATA150 7200 HDD, and installed it as directed by my t770.uk manual. Up until now, things looked to be on a roll. As I don't have any windows OS, I figured Ubunutu would be the way to go (and it certainly is from what I've heard and read about it. I can't wait!).
So I sent off for a CD and it popped through my mail a few weeks back. The problem that I am having is after booting past a very brief view of the HP POST screen, the screen goes black with the error "Disc boot failure-insert system disk and press enter". I've tried placing the Ubuntu disc in (assuming it is asking for that? An OS disc) and restarting, and changing the boot order around, but no matter what I do the error persists and I can't install Ubuntu. I really want to get this PC running with Ubuntu.
I am having a problem with my new Toshiba Satellite Laptop... I had installed debian for some time but last week suddenly stopped working.
- the computer stopped working at all... nor bios access.
- I did a new bootable installation in USB drive and downloaded the latest debian iso from official website and created the bootable device via dd as usual.
- I installed the new debian but after I removed the usb drive in order to boot into my new system. I was taken to a screen saying "Start PXE over IPv6 -- Start PXE over IPv4 ..." I followed several links looking for a fix, and all of them lead me to disable network boot option in BIOS setup...
- I disabled but after that it appears a new message "No Bootable device -- Press restart system" and nothing happens from there.
- I have found info in Internet regarding this issue, but all I find is "windows related"
- Someone recommended me this: "The BIOS can no longer recognize the hard drive as a bootable device. This could be for a number of reasons. Your best bet, if it is still under warranty, is going to be to bring it back to where you purchased it"
- But instead, what I did was to create a new bootable device, this time containing XUBUNTU and installed it to the machine, I had the good news that the installation proceed without any problem, so I could figured out that my machine it is still alive...
- Back to my issue and hoping that something unexpected happened that fixed the machine, I got back and did a new Debian bootable device, also hoping that the latest was corrupted or something, but after reboot to my new system... the problem persisted again.
- I chose to have 1 partition in full disk.
Now I don't know what else to do... I don't like ubuntu, I have used debian for some years and I want to keep using it and I would not like to be forced to move to ubuntu or xubuntu for this.
Today, I was downloading some stuff from online. I left for a few minutes and came back to find that someone had hit my loose power cord, causing the computer to restart. When I completed the reboot (It always says "Insert system disk and press enter" after checking CD drives), and had it load OpenSuSE 11.3 Failsafe (Regular won't work for me), it loaded into Teal (BASH, Command Prompt, Kommand, whatever you want to call it). At first, I thought maybe I screwed up and told it to load into that. But, I tried again, and it did the same. I tried using Non-Failsafe, and got the same results. I am able to edit, add, or remove programs from the Linux partition, though.
View 3 Replies View RelatedI'm trying to do exactly this: [URL] the first time i did it, I made it and everything was fine, except I didn't know what "installation size" meant in wubi, so as I selected 3GB, the rest of the partition was left empty and I didn't have enough space for ubuntu. Then I formatted the partition again and reinstalled ubuntu. Since then while it's booting, I get the message Disk boot failure insert system disk and press enter. I tried reinstalling many times, but I still get this message..
View 6 Replies View RelatedI've done an image according to:
[URL]
then I've copied it using:
Code:
# fdisk -l
Disk /dev/hda: 81.9 GB, 81964302336 bytes
255 heads, 63 sectors/track, 9964 cylinders
Units = cylinders of 16065 * 512 = 8225280 bytes
Disk identifier: 0x1145fa35
[code]....
I have dell laptop running with windows xp and im trying to install ubuntu 10.10 by booting it from a cd.
I verified the image I downloaded by comparing the hash and it worked out fine. I wrote the image into a cd and changed the booting priority on the BIOS to boot from the drive. When attempting to boot I get the "No bootable device found strike F1 to retry, F2 for setup or F5 to run onboard diagnostics" message.
I tried upgrading to Natty last night through the update wizard and the install went perfectly... until I rebooted and it got stuck at a screen with an "_" in the top left corner of the screen and nothing else. I guessed that this was a grub problem, so I tried reinstalling grub2, but to no avail. So, I burned a Natty install CD and proceeded to reinstall, formatting the partition (/home was on another partition and did not get formatted). Again, the install went great, rebooted and this time I get "No Bootable Device - Please insert a bootable device and hit enter". So, again, I try re-installing grub2 from the live CD. I purge, uninstall, and reinstall grub2... nothing works! What the hell?
View 1 Replies View RelatedI am dealing with a problem which I cannot seem to fix myself.I have a computer (age ~1 year) on which I am trying to install Ubuntu.The problem which I am facing is at the point of choosing to boot from the CD it says 'cannot find bootable device'.Note that this PC does not have a floppy drive and that I do not have a 1GB USB stick. I do have a 256MB USB stick.
View 9 Replies View RelatedBooted up system and it stated please insert system disk press any key.So it sounds like my startup got corrupted? I running centos 4.5 on it (old yes) Is there a repair I can perform by a disk? Would it matter if I chose i386 or x86? I cant remeber which version was installed on it.
View 8 Replies View RelatedI installed Debian Lenny on my HP Laptop - dv6-2120ed. Because i have atheros wireless card i needed to install ath9k which is not supported in 2.6.26 kernel so i compiled it to 2.6.32. Everything is good, but when i boot the new kernel i get "Bar 6: No parent found of for device" for 2 devices - the ethernet LAN card and the sound card. After 1 minute waiting the kernel starts booting and everything works fine (the LAN and the SOUND card too). How can i fix this and what means it exactly?
I tried with other kernel - 2.6.35 and 2.6.34
I run a program (findknxusb) to scan for devices on USB, but the device is not found.
The debugging level for libusb is on:
$ ./findknxusb
Possible addresses for KNX USB devices:
libusb_set_debug...
libusb: setting debugging level to 1 (on)
libusb_init...
[Code]....
I installed Debian Lenny on my HP Laptop - dv6-2120ed. Because i have atheros wireless card i needed to install ath9k which is not supported in 2.6.26 kernel so i compiled it to 2.6.32. Everything is good, but when i boot the new kernel i get "Bar 6: No parent found of for device" for 2 devices - the ethernet LAN card and the sound card. After 1 minute waiting the kernel starts booting and everything works fine (the LAN and the SOUND card too). How can i fix this and what means it exactly?
View 2 Replies View RelatedI get black screen when i press ctrl-alt-f1 or when i try to stop gdm, pressing alt-f7 nothing happens.
vga is ati hd 5650 how can i fix?
I got this keyboard no found error...no problem since my grub menu 1st entry is ubuntu...so once I got to load ubuntu, the keyboard magically works.
Basically when booting, it show "Keyboard not detected, press f1 to continue" then at the grub menu, I am not able to select win xp or anything. So by default 1st entry is ubuntu so I can boot into ubuntu.
Once ubuntu is loaded, I can use the keyboard to enter my password....
So I was wondering if the cmos battery is flat...but still why can't my key board be detected when booting up?
My os is debian 5.0, netcard is RTL8168D/8111D. I can't use the Static ip, if I setup static ip, output "not found network device", but the network driver have loaded and if I use DHCP mode everything is ok. do you understand my english? What my next steps should be?
View 7 Replies View RelatedI installed debian 4.0 (etch) on an old computer with some pickled graphics card in it, and then I upgraded the computer to one with slightly newer hardware only without the graphics card (the new one used on board graphics). I moved the hard drive from the old one to the new one but when I booted it up it failed to start the X-server and I got some errors listed for "device not found" and "no screens found".
I tried using "dpkg-reconfigure xserver-xorg" however I can't seem to find a working configuration. It seems pretty silly that when installing debian it can detect all this automatically with no problems but when it comes to changing some hardware around you are left in the dark with a complicated re-configuration process. Is there not some way to automate this? I'd rather not have to re-install everything
Dual PII 400, 512Mb with a Promise SuperTrak 100 IDE Array Controller. At present I have only one drive on the controller, configured for 1 JBOD array. I install FC9 with no problem. New partition is created and formatted, Grub is installed, and then... Grub is found and booted, but then I get:
Reading all physical volumes. This may take a while... No volume groups found Volume group "VolGroup00" not found Unable to access resume device (/dev/VolGroup00/LogVol01) mount: could not find filesystem '/dev/root' I can boot in rescue mode, chroot to the installed system. I changed the kernel boot parm "root=/dev/VolGroup00/LogVol00"
I have a Dell Vostro 3300, i5 460 processor with a NVIDIA 310M Graphics Card. I'm doing a KUBUNTU 10.10 (Maverick) install with the following results. The Live CD boots just fine to, "TEST," or "Install." Installation goes fine. However, the graphics card being used is the Intel i915. I have tried installing the NVIDIA drivers directly from the, "Additional Drivers," tool and after the reboot I get through the boot screen to the console. I try to manually startx and I get the errors, "no device found," "no screens found." The second install I tried purging and blacklisting the nouveau drivers and entering safe mode. Then using apt-get install nvidia-current. After that, nvidia-xconfig. Same results.
The third attempt I re-installed and this time downloaded the drivers from the Nvidia site (version 256.53). Blacklisted nouveau, remove all nvidia, updated initramfs, etc. The install went fine however I still end up at a console after boot with the same messages as above. No device found, no screens found. I've tried searching through the forum and web and have tried things like adding the modset option along with many other hacks, tips and fixes. still, no go.I can live with the Intel graphics for now although I lose 512MB of memory. Unfortunately there is no way to disable or change this set-up in the BIOS. I've seen quite a few bug reports at Launchpad:
1. Is this something I should just wait til a fix comes? Will a fix come?
2. Is there, or will there be an official Updated Ubuntu Guide for Maverick to install NVIDIA drivers with this tecnology?
3. Lastly, is there anything else I should try??
I just (for the first time ever) installed a version of Ubuntu. It is 10.04. I installed off of the Live Disk. I was having a great time until the first time I went to boot into it and I got the message
"Error: No such device: "long number" Grub Rescue> "
[Code]...
I've one lenovo 3000 g430 4152 laptop on which i have windows but previously installed debian 5.03 and for enabling the wireless i've to download broadcom b43legacy and install it by compiling because the backports kernel doesn't work with lenovo and after installing debian accidently switched of the wireless by the slide button on laptop
but on next boot i was not able to enable the wireless either by the slide button or fn+f5 which is the key for enabling it the wireless then on some forum i got advise that i can only re-enable by installing windows because lenovo drivers are available for only windows for this model... my question is that is there any solution for it in debian and also there is one more problem that i've to press fn+f8 twice on each boot for enabling the touchpad...
i need to add this line nameserver 208.67.122.221 from ISP before the first nameserver already exists in resolv.conf in all workstations i know
Code:
sed '/nameserver/ i
ameserver 208.67.122.221'
but that insert it on every line after nameserver not only before the first one
Code:
# blah blah
# blah blah
domain mydom.com
[code]....
I'm installing Fedora 11 x86_64 from the DVD iso. The SHA256 checksum was fine, and the media checked out fine just prior to install. The F11 install seems to go perfectly and I get all the way through the installation. However, on reboot, I get this message, "No bootable device -- insert boot disk and press any key"!!!!I'm installing to an old Intel 975XBX2 motherboard with 4GB of memory, which I have used successfully, flawlessly for every single Fedora install since F6. I've only been using one hard drive with a FAT32 partition, and an NTFS partition for Windows XP, the remainder of the disk is Fedora.I've probably tried this F11 install about 8 or 9 times already with no success; actually, the installation seems to go perfectly, but I just cannot boot the PC. I think there's something wrong with GRUB being written into the MBR of the hard drive, because I cannot boot DOS on that FAT32 partition, I can't boot into the NTFS partition which contains XP, nor can I boot into F11.Anyone else having problems with the boot? I've been a long time Fedora user and was counting on the reliability of F11: Wondering if that Anaconda re-write had anything to do with all of these problems?
View 14 Replies View RelatedInstalled ubuntu 10.4 over previous ubuntu on Intel 945G. After installation and reboot the system does not boot: "no bootable device - insert boot disk and press any key".
Installation was done from USB-stick, prepared by UNETBOOTin. I have two HD's, one used for system + storage, another one just for storage. I manually deleted previous system partitions of previous ubuntu install in system HD. The system HD had about 1/3 of free and unallocated space for system partitions, which ubuntu installer created during the installation.
I tried to reinstall grub from bootable USB-stick and it succeeded but it did not help. The system is still not bootable.
I have used ubuntu for years and never happened something like this. Am I missing something or is ubuntu missing something???
HW failure is ofcourse possible but I am quite skeptical about it because Live ubuntu from USB-stick works well.
i had a working multi-boot system, vista on sda1,2; swap sda3; ext=sda4; ubuntu sda5; fedora sda6; data sda7 - i mount the data partition when using all of the linux releases so i don't have to have multiple copies of music, docs, etc. everything has worked fine until yesterday. i tried to install fc12 on sda6, replacing fc11. it required me to format sda6 as ext4. i wasn't sure where i had grub installed, but have a backup of menu.lst in data (sda7), so figured i could let it install to mbr or wherever it wanted to by default. when the install completed and i reboot, i get a black screen and these messages: CLIENT MAC ADDR: 00 19 XX XX XX GUID: XXXXX PXE-E53:
No boot filename received
PXE-M0F: Exiting Intel Boot Agent.
No bootable device -- insert boot disk and press any key I tried reinstalling fc12, same exact errors. I then thought maybe the problem had something to do with ext4 partition mixed in with ext3's, so i installed mepis on the sda6, and let it write grub to mbr (i think, not really sure where it wrote it). anyway, i still get the identical black screen. no grub type menu or anything. the screen used to show "DHCP for a few seconds", but doesn't anymore after i disconnected the ethernet cable.........
- Old laptop with only PATA
- Bought a PCMCIA ESATA card and a SATA SSD in an external enclosure
- Bios is too old to support booting from the PCMCIA device
I bought an SSD to speed things up a little, but having some issues.
Since I can not boot from the SSD, I thought I'd load the kernel from the old PATA disc and then mount / to the SSD.
== What i've tried: ==
(sda = internal pata)
(sdb = external ssd)
1. Installed ubuntu to sda with seperate paritions for /boot /var /srv and /
moyd@A:~$ df
Filesystem 1K-blocks Used Available Use% Mounted on
/dev/sda9 4804736 2012760 2547908 45% /
none 508764 376 508388 1% /dev
[Code].....