I've been trying for a couple of days now to get the Huawei E1750 to work but have had no luck so far. I've installed the packages usb-modeswitch-1.1.4 and usb-modeswitch-data and have edited the usb-modeswitch.conf to include the following:
DefaultVendor= 0x12d1
DefaultProduct= 0×1446
TargetVendor= 0x12d1
[code]....
setup and configure a Huawei E1750 modem on mandriva!
View 5 Replies View RelatedI'm trying to make a Huawei K3715 HSDPA modem work in Ubuntu 10.04.1. I plug it in, and it loads two mass storage devices (one CDRom containing the Windows software, and one 2GB drive that appears empty), but I don't really know where to go from here.
Note that I replaced the stock network manager with Wicd, as I find it more reliable in picking up wifi connections. I'm not sure if it's suitable for connecting the HSPA modem though.
I have upgraded my Acer Aspire One from 10.10 to 11.4. My T-Mobile UK Broadband Dongle worked fine until then, and now it won't work. It starts flashing green (as it did before) and then it flashes blue. I can see a Mobile Broadband option in Network Manager (including the settings that worked in 10.10). However, a right click on the network icon in the top panel does NOT give me any corresponding (T-Mobile) connect option, nor is there anywhere in there with a check against Mobile Broadband as there was in 10.10
View 1 Replies View Relatedi am having trouble setting up my alltel wireless in lenny in ubuntu i used modem-manager and usb-modeswitch. but modem-manager isnt supported in lenny is there any other way to set this device up?
View 1 Replies View RelatedI am very new user of ubuntu..
migrated from windows.
but not able to install my 3g modem e1750
How to install "Huawei E156G Modem" in Ubuntu O.S. Are there any special code for configure it. I plug modem but i can't conect to internet. This message appear " you're offline".
View 4 Replies View Relatedhow configure E1550 Huawei modem in Ubuntu9.10.
View 1 Replies View Relatedubuntu I can not use a wireless modem huawei 160.type can only be used in windows.well to be used in my ubuntu linux? whether there is a script that used.
View 2 Replies View RelatedI'm using ubuntu 10.04. My Huawei E156G 3g modem doesn't work with ubuntu, It's detect as a storage device not a modem.
View 2 Replies View RelatedI just installed debian lenny. I'm looking forward to getting some work done with it, and I'm learning loads. When I was installing it, the GUI screen showed me three network interfaces, so I chose wlan0, the wireless card, so it did pick it up?
I tried to configure it with the necessary information (I wrote it down on a pad) but it still wouldn't configure, so I said, continue with the install and do it later. When I got to the desktop I added a new network to in network manager and set the ESSID and password, but still nothing. Even a list of other networks don't show up.
So what do I have to do to get this working? Here are the stats:
Atheros Communications Inc. LAN Express AE IEEE 802.11g PCI-E adaptor.
Have my proxy running on Lenny and tried to upgrade to squeeze. Originally the system was installed on Etch and upgrading to Lenny was no problem. In the system i have two RAID1 volumes, md0 for / and md1 for /home. For upgrading i added the sources to my apt.conf and startet dist-upgrade. During the installation procedure, when installing udev I was advised to install the new kernel first and continue upgrade after booting the kernel. so I installed the kernel by "apt-get install linux-image-2.6-686. When generating initramfs there was a message, that there are no arrays defined in /etc/mdadm/mdadm.conf I took a look and there were none. mdadm seems to have been update before.
I then added the lines for RAID definition and added the data for UUID The UUID I got from the output of "mdadm --detail /dev/md0"
What I don't understand: blkid gives the same UUIDs for the first partitions of the RAID and a different UUID for /dev/md0 and /dev/md1 than mdadm --detail The update of initramfs for kernel 2.6.32 then gives this result:
update-initramfs -u -k 2.6.32-3-686
update-initramfs: Generating /boot/initrd.img-2.6.32-3-686
W: Possible missing firmware /lib/firmware/e100/d102e_ucode.bin for module e100
W: Possible missing firmware /lib/firmware/e100/d101s_ucode.bin for module e100
[code].....
After running wireless for years my system crashed, I've had to re install lenny and now what ever I try I can't get the wireless to work. I'm running Lenny, kernel 2.6.26-2-686 but when I start up it doesn't seem to be able to start the wireless, whatever I do from gnome wireless tools,
dmesg | grep -i iwl
shows this
[9.663570] iwl3945: Intel(R) PRO/Wireless 3945ABG/BG Network Connection driver for Linux, 1.2.26ks
[9.663570] iwl3945: Copyright(c) 2003-2008 Intel Corporation
[9.663570] iwl3945: Detected Intel Wireless WiFi Link 3945ABG
[9.725672] iwl3945: Tunable channels: 13 802.11bg, 23 802.11a channels
[9.736286] phy0: Selected rate control algorithm 'iwl-3945-rs'
[20.518187] firmware: requesting iwlwifi-3945-1.ucode
[20.654215] iwl3945: iwlwifi-3945-1.ucode firmware file req failed: Reason -2
[20.654215] iwl3945: Could not read microcode: -2
[23.376244] firmware: requesting iwlwifi-3945-1.ucode
[23.385408] iwl3945: iwlwifi-3945-1.ucode firmware file req failed: Reason -2
[23.385408] iwl3945: Could not read microcode: -2
[40.503987] firmware: requesting iwlwifi-3945-1.ucode
[40.519721] iwl3945: iwlwifi-3945-1.ucode firmware file req failed: Reason -2
[40.519728] iwl3945: Could not read microcode: -2
The end statements repeat many times.
What include support a driver for USB modem Huawei E219 (HSDPA/UMTS) and Huawei EC226 (3G/EVDO)?
View 1 Replies View RelatedI have recently bought a branded Onda MT835UP USB broadband modem. The hardware comes with its own drivers/GUI for linux, however I'd rather use the Debian-provided NetworkManager+modemmanager packages.
A few details:
- I'm using debian unstable,
- latest NetworkManager 0.8.2-3 from experimental
- latest modemmanager 0.4+git$foo from testing
- latest usb_modeswitch[_data] from experimental
[Code]....
I have a 3G modem Huawei e173s-6, the usb id is 12d1:1c0b. It's only detected as storage, not as modem. According to some tutorials I've found, I had to use usb_modeswitch and udev rules to make it automatically switch to modem mode, and usb id 12d1:1c05. I followed the tutorials, and the usb changes the id, but after the switch it is still recognized only as storage.
I have the suspicion that I have to add the driver to the kernel, since this is 11.3, but I haven't the slightest clue what to do. Does someone have experience making this modem work in 11.3? tutorial: USB_ModeSwitch ~ View topic - Huawei E173s working config
with installing Modem Huawei E170. my modem can not connected and suddenly remove from my PC. i am using Ubuntu LTS 10.04.
View 1 Replies View Relatedi'm running Kubuntu karmic and i've been using a 3G Huawei E1552 modem to connect to the internet, everything was going well when suddenly my modem stopped working. I've tried reconfiguring everything, i even reinstalled kubuntu from scratch with no success.Here's a part of my /var/log/debug
HTML Code:
Feb 8 17:14:01 alberto-laptop kernel: [ 1532.099883] usb-storage: device found at 7
Feb 8 17:14:01 alberto-laptop kernel: [ 1532.099888] usb-storage: waiting for device to
[code].....
I am runing debian-5 (lenny), the default kernel 2.6.26 was unable to start the x so i installed the new kernel linux-image-2.6.32-5-686_2.6.32-28_i386.deb, now x works, but there is problem building modules for the intel soft modem linux driver hsfmodem-7.60.00.00oem which is supplied in the modem cd by the intel company.
I installed these kernel packages for this purpose:
linux-base_2.6.32-28_all.deb
linux-image-2.6.32-5-686_2.6.32-28_i386.deb
linux-headers-2.6.32-5-486_2.6.32-28_i386.deb
[code]....
in all these cases hsfconfig failed with the above error,
I have a wireless router in my room and when people use their WiFi devices in the living room the signal is very weak and really slow, i have a Debian box in the living room that i would like to use as a wireless repeater. i want it to receive the wireless signal from my router and transmit an AP that resembles the one being transmitted by the router is this possible, and how can it be done
View 9 Replies View RelatedI have a Dell Mini 9 with a Broadcom wireless adapter. I've had it working for months on Debian Sid, but recently I updated the entire OS to get KDE 4.4 (I also went from a 2.6.30 to a 2.6.32 kernel). Something in that upgrade caused wireless to cease to work properly. The problem is similar to the one described in this thread, but no resolution is mentioned there: viewtopic.php?f=5&t=50892 I've gone through all the steps to install the STA drivers/wl module for it, and it basically appears to be working. Using wicd, I can see all the wireless networks in the area.
The problem occurs when trying to connect. When I try to connect to my WPA wireless network, it eventually fails claiming a bad password. When I turned the wireless network into an unsecured network, it eventually fails claiming it's unable to get an IP. I've also tried at the command line with wpa_supplicant and it initially appears to work but in fact it hasn't. I've also got Kubuntu 10.04 installed on this machine, and it can connect without issue (using the proprietary driver that Ubuntu's hardware driver manager allows one to use).Does anyone know what has caused this? I even tried the earlier kernel, so that's not it.
I want fn* keys working for all users in all DE/WM and at tty too. I want it even if nobody logged in. Is it possible? How to set it up?
I mean these keys:
toggle wifikbd backlight +/−screen backlight +/−enable/disable screentoggle screensenable/disable touchpadvolume controls
I understand that some of them may work only with Xorg (e.g. toggle screens), but screen and kbd backlight and volume may work at tty too (because I can change this from tty when xorg is down). I know how to do it all from the console, but I want to bind keys with actions.
E.g. I can change kbd backlight with dbus and attach this action to key in my wm config, but it is not what I want. I want to make it global. I don’t understand which layer may provide the functionality for all users. Now only two keys works as I expect: toggle wifi and toggle touchpad. I haven’t set it up, it works out of the box.
Asus N56VZ, Debian stretch.
Code: Select alluname -a
Linux isquabook 3.16.0-4-amd64 #1 SMP Debian 3.16.7-ckt11-1 (2015-05-24) x86_64 GNU/Linux
I have amd64 Debian Jessie and i386 Debian Jessie installed on my laptop. I wanted to start x86 app that is installed on my x86 OS from my amd64 OS using chroot.
My mounts inside chroot:
Code: Select all/dev/sda7 on / type ext4 (rw,relatime,data=ordered)
/dev/sda5 on /tmp type ext4 (rw,relatime,errors=remount-ro,data=ordered)
/dev/sda5 on /etc/resolv.conf type ext4 (rw,relatime,errors=remount-ro,data=ordered)
tmpfs on /dev/shm type tmpfs (rw,relatime)
proc on /proc type proc (rw,relatime)
devpts on /dev/pts type devpts (rw,relatime,mode=600,ptmxmode=000)
none on /sys/fs/cgroup type tmpfs (rw,relatime,size=4k,mode=755)
systemd on /sys/fs/cgroup/systemd type cgroup (rw,nosuid,nodev,noexec,relatime,xattr,release_agent=/lib/systemd/systemd-cgroups-agent,name=systemd)
/dev/sda5 on /var/lib/dbus/machine-id type ext4 (rw,relatime,errors=remount-ro,data=ordered)
sda5 is host OS and sda7 is guest OS
when I start any x86 app I can see "failed to create secure directory (/run/user/1000/pulse) permission denied" how to make pulseaudio to work inside chroot?
also what this command exackly does?
"pactl load-module module-simple-protocol-tcp rate=48000 format=s16le channels=2 source=auto_null.monitor record=true port=8000 listen=127.0.0.1"
I'm having trouble getting my wireless card (RNX-G300LX, from Rosewill) working with my Debian install. I had it working at one point in time, but (apparently) something has gone wrong, as it no longer connects. The network I'm trying to connect to uses WPA2. When I try to start up my wireless card as follows:
# ifup wlan0
I get the following response:
wmaster0: unknown hardware address type 801
wmaster0: unkown hardware address type 801
Listening on LPF/wlan0/00:1a:...
Sending on LPF/wlan0/00:1a:...
Sending on Socket/fallback
DHCPDISCOVER on wlan0 to 255.255.255.255 port 67 interval 4
DHCPDISCOVER on wlan0 to 255.255.255.255 port 67 interval 10
DHCPDISCOVER on wlan0 to 255.255.255.255 port 67 interval 15
DHCPDISCOVER on wlan0 to 255.255.255.255 port 67 interval 17
DHCPDISCOVER on wlan0 to 255.255.255.255 port 67 interval 12
DHCPDISCOVER on wlan0 to 255.255.255.255 port 67 interval 3
No DHCPOFFERS received.
No working leases in persistent database - sleeping.
I have set up /etc/network/interfaces as follows:
auto lo
iface lo inet loopback
iface wlan0 inet dhcp
wpa-conf /etc/wpa_supplicant.conf
auto wlan0
and /etc/wpa_supplicant.conf looks like this:
ctrl_interface=/var/run/wpa_supplicant
ctrl_interface_group=0
ap_scan=1
fast_reauth=1
network={
ssid="apt_102"
scan_ssid=1
key_mgmt=WPA-PSK
psk="mypassword"
proto=WPA2 }
I should also note that running wpa_cli -i wlan0 tells me that it is "trying to associate" with my router, but authentication times out each time.
I have an Atheros wireless USB dongle that will connect to my Wifi network just fine in Gnome but in KDE doesn't. I've read through the http://wiki.debian.org/WiFi/HowToUse and have installed all packages and tried all methods noted there but still can't get the wlan0 to work at all in KDE. Is wireless in KDE & Debian Squeeze useless?
View 3 Replies View RelatedI have got a laptop running Debian squeeze. I wish to share the wireless connection of the laptop (wlan0) to the ethernet port of the laptop, so that I can share the wireless connection to my desktop PC which is connected to the ethernet port.
[My desktop PC]---Ethernet---[My laptop]---))) WiFi )))---[Public network/ ISP]
I have read the article on Ubuntu community: [url]
I followed the steps, and the /etc/network/interfaces file on my laptop is:
Now the situation is: My laptop can connect to Internet (i.e. ping debian.org from laptop is fine), my desktop PC can connect to my laptop (i.e. ping 192.168.1.1 from desktop PC is fine). However, the desktop PC cannot reach the Internet.
I also read the information on Debian Wiki: [url]
It seems I must install and configure ebtables before sharing my wireless connection to ethernet port. Is it true? (But why the article on Ubuntu community doesn't mention it?) Or I just made some mistakes?
I am unable to get my intel pro/wireless 3945abg connected to my router. The firmware has been installed and at first was even able to connect, but now the access point doesn't even show up in network manager. I am currently able to connect using a USB wireless adapter, but for certain reasons, would prefer to use the former. I've looked over this page with no results.
View 7 Replies View RelatedTo configure SMS gateway using Kannel configuration for Huwei GSM Modem
dmesg gives attached modem in my system:
How to make the modem lights toolbar addon to work? They don't seem to work while online with Gnomes KPPP, and it would be nice to see them working while online.
View 2 Replies View RelatedI have a USB huawei ec1262 wireless internet stick from Reliance. I google'd on how to install it. I am using Debian Lenny. I know that there is a "mode-switch" package that needs to be installed but this is not available on the down load package list for Debian. i can find this & also instructions if possible on how to get this working on my Lenny system .
View 5 Replies View Related
