Debian Configuration :: Wireless Won't Make Connection After Upgrade?
May 15, 2010
I have a Dell Mini 9 with a Broadcom wireless adapter. I've had it working for months on Debian Sid, but recently I updated the entire OS to get KDE 4.4 (I also went from a 2.6.30 to a 2.6.32 kernel). Something in that upgrade caused wireless to cease to work properly. The problem is similar to the one described in this thread, but no resolution is mentioned there: viewtopic.php?f=5&t=50892 I've gone through all the steps to install the STA drivers/wl module for it, and it basically appears to be working. Using wicd, I can see all the wireless networks in the area.
The problem occurs when trying to connect. When I try to connect to my WPA wireless network, it eventually fails claiming a bad password. When I turned the wireless network into an unsecured network, it eventually fails claiming it's unable to get an IP. I've also tried at the command line with wpa_supplicant and it initially appears to work but in fact it hasn't. I've also got Kubuntu 10.04 installed on this machine, and it can connect without issue (using the proprietary driver that Ubuntu's hardware driver manager allows one to use).Does anyone know what has caused this? I even tried the earlier kernel, so that's not it.
View 1 Replies
ADVERTISEMENT
May 19, 2011
I have a wireless router in my room and when people use their WiFi devices in the living room the signal is very weak and really slow, i have a Debian box in the living room that i would like to use as a wireless repeater. i want it to receive the wireless signal from my router and transmit an AP that resembles the one being transmitted by the router is this possible, and how can it be done
View 9 Replies
View Related
Mar 1, 2010
I have got a laptop running Debian squeeze. I wish to share the wireless connection of the laptop (wlan0) to the ethernet port of the laptop, so that I can share the wireless connection to my desktop PC which is connected to the ethernet port.
[My desktop PC]---Ethernet---[My laptop]---))) WiFi )))---[Public network/ ISP]
I have read the article on Ubuntu community: [url]
I followed the steps, and the /etc/network/interfaces file on my laptop is:
Now the situation is: My laptop can connect to Internet (i.e. ping debian.org from laptop is fine), my desktop PC can connect to my laptop (i.e. ping 192.168.1.1 from desktop PC is fine). However, the desktop PC cannot reach the Internet.
I also read the information on Debian Wiki: [url]
It seems I must install and configure ebtables before sharing my wireless connection to ethernet port. Is it true? (But why the article on Ubuntu community doesn't mention it?) Or I just made some mistakes?
View 1 Replies
View Related
Aug 17, 2011
Testing distribution. Installed Linux 3.0 but left 2.6.32 on as backup. When I boot into the old kernel, wireless mostly works OK, but never when I boot with the new kernel.
Results of dmesg|grep wlan0 on 2.6:
[ 22.005102] ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 28.196774] ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 28.644779] ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 30.688053] wlan0: direct probe to AP 00:19:5b:06:9f:ba (try 1)
[ 30.694053] wlan0: direct probe responded
[Code]...
Noticing the Access Point looked like it needed the MAC address, I ran iwconfig wlan0 ap <MACADDRESS> and sometimes it will work, and wicd can connect to the access point. But sometimes the command fails to run.
View 4 Replies
View Related
Apr 17, 2011
I upgraded from lenny to squeeze on a notebook and I can no longer connect to the wireless network. The computer is an LG notebook and the network card is ralink rt2860. I am using Gnome and NetworkManager. The wireless key is WEP hex. It was working fine with lenny till before the upgrade. After the upgrade, the network card stopped working. So, I checked
$ lspci|grep Network
08:00.0 Network controller: RaLink RT2860
Then I reinstalled the driver with apt-get install firmware-ralink wireless-tools Then the network manager tray started working again and saw the network, but cannot connect. It was trying to connect but timed out and kept asking for the password. It is the correct password. I tried deleting the old connection and recreated a new one in the nm. But still does not work.
[Code]...
View 7 Replies
View Related
Oct 10, 2010
I've been trying for a couple of days now to get the Huawei E1750 to work but have had no luck so far. I've installed the packages usb-modeswitch-1.1.4 and usb-modeswitch-data and have edited the usb-modeswitch.conf to include the following:
DefaultVendor= 0x12d1
DefaultProduct= 0×1446
TargetVendor= 0x12d1
[code]....
View 3 Replies
View Related
Apr 23, 2011
I own an ASUS N61JV-X2 notebook PC. It has an Atheros Communication, Inc. AR9285 Wireless Network Adapter. 03:00.0 Network controller: Atheros Communications Inc. AR9285 Wireless Network Adapter (PCI-Express) (rev 01) 03:00.0 0280: 168c:002b (rev 01) I cannot see any SSIDs including my home Verizon FiOS 802.11 G WPA2-AES-TKIP encrypted network. I went to Starbucks to try to connect to their free Wi-Fi and I could not make a connection. How do I solve this problem so that I can connect to a SSID of my choice and make a wireless connection while using GNOME 3?
View 2 Replies
View Related
Apr 15, 2011
1 linksys router: gets the net from PPPOE and give the network DHCP. The router IP is 192.168.1.1. 1 windows laptop that work wireless and wired. 1 debian desktop that work wired and not working wireless. THe problem with the debian desktop is like this: I have a TP-Link TL-WN321G installed and found by lsusb command. I make a wireless connection WPA Personal (just like the router settings) it says i am connected to the wl network but no internet connection. the route command give me this:
[code]....
I tryed with wicd who said that the connection is WEP (and it's not, it is setup to WPA on the router and the network-manager conncetion) and when i try to connect i get bad password. I tryed with network-manager uninstalled and no chance.
View 4 Replies
View Related
Mar 26, 2016
I build and use a custom kernel, and use the nvidia driver. This is on debian stretch.
By default, I build the image and headers packages with this line:
CONCURRENCY_LEVEL=8 nice -n19 ionice -c3 fakeroot make-kpkg --initrd --append-to-version=-something --revision=1 kernel_image kernel_headers
These kernel sources are usually the sources from debian, with a couple of more patches that I add. It appears that for nvidia-driver package versions higher than 352.79-1, the kernel headers/sources need to be prepared with 'make prepare' and 'make prepare scripts'. It's that simple. I concluded this after the nvidia dkms build failed on my custom kernel, but then succeeded after I pointed it to the full sources, but only after running 'make prepare' and 'make prepare scripts' on them. The problem is that this make-kpkg scheme doesn't appear to do this, or if it does, it doesn't properly include in the headers everything that it should.
View 0 Replies
View Related
Sep 22, 2015
The situation: The office has a WiFi network on one DSL line, which is used for our VoIP call center, and a wired network for our internal network and the majority of web surfing/traffic . Part of the office must be temperature controlled/monitored - we have a rather nice digital thermometer which is WiFi enabled.I have a Debian Wheezy box with a WiFi card and ethernet connection
What I'm trying to accomplish:Connect wifi enabled thermometer to WiFi network so it can automatically send temp updates (currently I have to do it manually via USB)Have the Wheezy box accept the downloaded file then send it to a back up server in the wired network
Side things that may be useful : Prefer to use wired connection for internet and apt and suchWiFi connection will really just be used for connecting to the thermometer
This [URL] .... topic got me thinking that there might be a way to bring the two networks together, but I don't know if that will wreak havoc on things. I know, the Windows and Mac OS don't like having ethernet and wifi at the same time, might Linux be better for this?
v&n had this to offer in the prior thread [URL] .... which I'll be doing more research on.
View 2 Replies
View Related
Jun 27, 2011
I'm working with linux opensuse 11.4. It recognizes the wired ADSL connection but it does not recognize the wireless connection. how to make a wireless connection in this os?
View 2 Replies
View Related
May 18, 2010
I did a clean install of 10.04 on my Toshiba Satellite laptop, but I cannot make a wireless connection. The icon on the panel spins round and round, but that's it. After a few minutes I will get a message that the wireless network is disconnected. Any ideas?
View 9 Replies
View Related
Nov 12, 2009
Each time I start up debian -lenny, the network-manager does not automatically connect me to my wireless network. The connection list shows a lot of networks available, but mine is always absent from the list. This means I each time have to go to "Connect to other Wireless Network" in and write in my network name (SSID) and password (PWA2 Personal). Then is connects nicely and everything works fine until next time I boot
View 5 Replies
View Related
Oct 26, 2010
It's my very first time to use Ubuntu. I have just installed it but I can't figure out how to make my wireless internet connection work..
View 2 Replies
View Related
Dec 18, 2009
I've got an old Compaq Armada E500 laptop (850mhz PIII, 512mb RAM, 30GB HD) that I've been running OpenSUSE 11.1 w/Gnome desktop. My wireless adapter (Linksys Wireless-G, model WPC54G ver. 2 w/acx-111 chipset) worked well with this setup, but no that I've upgraded to OpenSUSE 11.2 w/KDE, I've got to start all over. I tried doing what I did before, which was to copy the firmware file into /lib/firmware.
View 9 Replies
View Related
Sep 26, 2010
Having just installed OpenSuse 11.3, NetworkManager identifies my wireless network, but repeatedly fails to make a connection. Without further ado, here are the outputs to commands requested in the first sticky thread:
[Code]....
View 7 Replies
View Related
Apr 23, 2011
I think I've read every post here about the Broadcom and connection.I thought I tried everything.Turns out (read Chapter�35.�Using NetworkManager) using Connection Manager (K Network Manager) you can not use, what I wanted to use, 'all users, use connection' or said another way, the wifi would be activated and connected Before the user 'logs in'. Well, as I said, it turns out that if you are using gnome, this will work with NetMgr, but NOT in KDE. If you want to use 'system connect' then you have to use 'traditional' if in YaST2. Oh well, at least 'i'm' connected.... (i'm the only user, so not a big deal right now, but would like to get it working...)
View 2 Replies
View Related
Jul 3, 2009
Can I upgrade from Fedora 9 to fedora 10 from a wireless connection? What I want is to upgrade without using a cd or usb device. I would like to use yum or packagekit. Can it be done? I just don't have any device or cd/dvd with me.
View 1 Replies
View Related
May 5, 2010
NOTE: My upgrade wasn't smooth. Now everything is extremely slow. However if I boot from the disc to try without installing, the connection problem is still there. There is an exclamation mark on the connection applet, right clicking shows that Enable Wireless is unchecked and unclickable. I've included outputs of common network commands which might prove to be useful.
Code:
[~] ifconfig
eth0 Link encap:Ethernet HWaddr 00:1e:33:60:f0:3c
UP BROADCAST MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
[Code]...
View 8 Replies
View Related
Apr 8, 2010
I have ubuntu 9.10 and my wireless connection has been working perfectly until a few weeks ago when I updated my laptop. I can connect to the internet using my wired cable but not by wireless. There is nothing listed under my wireless list. I am new to this and have been unsuccessful in getting my wireless connection going again. I don't even know were to begin. I have a 2wire modem also.
View 2 Replies
View Related
Aug 17, 2011
HTML Code: first I'll provide the requested information (from the sticky)
64-bit openSuSE 11.4
uname -a output
Linux linux-mx43 2.6.37.6-0.7-desktop #1 SMP PREEMPT 2011-07-21 02:17:24 +0200 x86_64 x86_64 x86_64 GNU/Linux
dmesg | grep firmware
[ 127.965048] b43legacy-phy0: Loading firmware version 0x127, patch level 14 (2005-04-18 02:36:27)
lspci output:
[Code]...
I've configured the device for my network's settings in YaST's Network Settings tool. Is the card turned off by the kill switch? Where do I find the kill switch?
View 7 Replies
View Related
Dec 1, 2009
I've got an old Compaq Armada laptop (850 mhz PIII processor, 512mb RAM, 30GB HD, DVD ROM) that I've been running OpenSUSE 11.1 on in a dual boot configuration with WinXP for almost a year. I've downloaded and burned a LiveCD of OpenSUSE 11.2 and booted the computer with it. Very impressive. I want to install it on the HD without doing a clean install. That is, I want to replace 11.1 and keep the WinXP partition intact. My biggest trepidation is getting the wireless card configured again. It was a bear the first time. Is there a way to update OpenSUSE without losing those settings?
View 9 Replies
View Related
Mar 16, 2011
I know that boot partition is possible to create within debian distribution that has grub 2.0, as I have done before with ubuntu. I have been trying many different options with my preseed file but it keeps taking the boot partition out of LVM and creating and extended partition too and then creates the LVM primary partition.
### Partitioning.
# you can specify a disk to partition. The device name can be given in either
# devfs or traditional non-devfs format. For example, to use the first disk
[code]....
View 1 Replies
View Related
Jan 16, 2010
I have an odd problem in that my wireless connection is okay until I close the laptop. When I open it back up, I'm unable to reconnect. This problem first occurred after upgrading to 9.10. I can reconnect after restarting. I tried several things before breaking down and reinstalling 9.04. After installing 9.04, everything works great. Any suggestions on what is going on before I try upgrading to 9.10 again? I have a Dell D600.
View 8 Replies
View Related
May 2, 2010
Since I upgrade to Ubuntu 10.04 my wireless connection is very unstable. I install the needed wireless drivers from 'Hardware Drivers' (Broadcom STA wireless driver) and I got wireless connection, but it randomly disconnect, and also connection is very slow.
I think that the problem are the drivers which are not very compatible with this version of Ubuntu, which means we need to wait for update? I have HP ProBook 4510s laptop, Intel PRO/Wireless 5100 AGN network card & Gembird NSW-R2 router. I'm only having this problem on Ubuntu 10.04, on other OS's the internet is fine.
View 7 Replies
View Related
Oct 18, 2010
For some reason from a fresh installation on Debian (Squeeze), Apt is telling me I no longer need the 'make' package and I can remove it. I find this extremely odd & random given I just built this O.S. Why would Debian want to remove such a package and since this is a fresh installation, is there something I did wrong?
View 4 Replies
View Related
May 10, 2010
Ok, so I upgraded my acer aspire one to the new Ubuntu 10, and at first everything was working fine, except the audio. Now, for some reason, my wireless and ethernet ports have died. I can't get online by either method. I can do ifconfig <device> up and it will show up if i do iwconfig or ifconfig, but the wireless isn't associated with the AP. Currently I'm trying to load some drivers for my atheros card, and we'll see how that works outReally I was wondering, how come the modules don't load at boot time, and how can I fix this? I've been a Linux user for quite sometime, however I've been more of end user
View 1 Replies
View Related
Feb 29, 2016
My Debian Jessie system started to bug after a separate /usr partition being full. After redimensioning and various packages reinstalls I fall on this:
systemctl --user status Failed to get D-Bus connection: Erreur inconnue -1
View 1 Replies
View Related
Aug 27, 2010
I configure my system in a long time and now I have a suitable system! But I install all directories in one partition and now I like install again, but I need make an image of my configuration for install from it and after install I don't spend time for again configuration.
View 2 Replies
View Related
Nov 28, 2015
It seems that my network manager may be running in root mode...
For instance in network connections, edit and delete are greyed out. if i click add, i am unable to enter any details. if i run nm-connection-editor as root i am able to make changes.
How can i set it that the normal user can make changes? [managed is set to true in the conf file]
View 6 Replies
View Related
