on my dual HD5500/GT940M. I can not turn on Nvidia. just install bumblebee and got the error "unknown header type 7f" if I remove bumblebee, Nvidia 340 loaded but system run on HD5500, no way to use Primus or to switch to 2nd card.
View 0 RepliesUsing online Debian guide, installed latest nvidia-current, glx etc which seems to be 195.xx Machine boots to GUI but monitor setting menu doesnt respond nor is there an nvidia specific one. xorg.conf shows 'nvidia' driver but I suspect I am still on 'nouveau' since the synapatic package manager doesn't show an nvidia xserver-xorg-video choice.
Second question, any trailheads for using wheezy based drivers (i.e. nvidia's latest 270.xx) with squeeze?
Lately, my rxvt-unicode has been generating this ~$ top 'rxvt-256color': unknown terminal type. Many of the terms have a colour patch. Where is the one for rxvt? Is there one in Debian or do I have to get creative?
View 2 Replies View RelatedI recently upgrade my armel NAS from etch to squeeze. During the partitioning step of the installation I intentionally left unmounted the data partition (900GB formatted XFS) but after the installation I'm not able to mount it.
I edited the fstab file adding the last line
And tried a mount but I get the message
So i noticed throught lsmod that I don't have the module for xfs
Tried installing xfsprogs but it didn't helped. So I searched for xfs-modules but seems it doesn't exists for armel architecture. Am I right? What does it means? That XFS is not supported in armel Squeeze? Assumed I can't transfer/backup 900GB of partition, is there a way to convert it on-the-fly to a supported filesystem format?
I had windows with ntfs I installed ubuntu. All ok. Gurb with 2 os, can ran windows and ubuntu and can mount ntfs partition in ubuntu I installed debian with lvm over ubuntu partition. I can't mount ntfs partition now, and windows doesn't appears in gurb
# mount /dev/sda1 /mnt/windows/
mount: unknown filesystem type 'LVM2_member'
# pvs --all
PV VG Fmt Attr PSize PFree
/dev/dm-1 -- 0 0
/dev/dm-2 -- 0 0
/dev/root -- 0 0
[Code]....
I can't active vg because haven't name, but is not lvm, is only ntfs partition Maybe ubuntu puts in lvm and grub? Any idea? If I change with fdisk to ntfs i lose all the information in the partition?
[Code]...
I just loaded octave. I ran through a few examples of how to implement a script file. Everything works until I get to "plot". When I run the "plot" command I get the following.
octave:2> test1.m
error: can't perform indexing operations for <unknown type> type
sh: gnuplot: not found
Just to double check my work, I ran the following code:
y=[1 2 3];
plot(y);
I'm trying to install the nvidia drivers but it is not working.
lspci | grep VGA
02:00.0 VGA compatible controller: nVidia Corporation NV18 [GeForce4 MX - nForce GPU] (rev a3)
My xorg.conf looks like this:
# xorg.conf (X.Org X Window System server configuration file)
#
# This file was generated by dexconf, the Debian X Configuration tool, using
# values from the debconf database.
[code]...
And after that my X is not working. And when i try sudo modprobe nvidia I get this:
FATAL: Error inserting nvidia (/lib/modules/2.6.26-2-686/nvidia/nvidia.ko): No such device
my server into the public internet and must have my webserver [2.2.9 (Debian)] act secure. But this does not look very easy [I am searching, reading and working on it already the whole day ]. I read the apache docs, but there is a lot of stuff, which is different in Debian [lenny, 5.0.6]. Apache ignores the host-header given by the browser: [URL] are all served, but should be blocked. I new new to apachy, but on my IIS this works as expected. All browsers act equal [so no browser header problem].I configured two VirtualHosts, an excerpt:
NameVirtualHost hugo:80
<VirtualHost hugo:80>
DocumentRoot /usr/share/doc
[code]....
The I go to my hosts file on any box, and add hugo's ip-address under the new name x. Then, x is served, although the host-header in apache Every user coming from the internet could make the same!
I recently installed office 2007 under wine, but since I have it no longer know what to open .doc or .xls files with, I was using Gnumeric but now when i go to Properties -> "Open with" there is no longer anything in the list and even when i attempt to add to the list nothing comes up. If anyone know what way you can manually add file types and associate them with programs
View 1 Replies View RelatedI have installed an HP LaserJet 2200 network printer using CUPS successfully and can print test pages and stuff from OpenOffice, Evince etc. But no luck printing from lpr. Using lpstat seems to suggest all is well:
$ lpstat -t
scheduler is running
system default destination: HP-LaserJet-2200
device for HP-LaserJet-2200: socket://192.168.10.42:9100
HP-LaserJet-2200 accepting requests since Tue 19 Oct 2010 14:01:50 NZDT
printer HP-LaserJet-2200 is idle. Enabled since Tue 19 Oct 2010 14:01:50 NZDT
Ready to print.
If I now try to print 'test.txt' using:
$ lpr test.txt
nothing happens. Try calling the printer by name:
$ lpr -P HP-LaserJet-2200 test.txt
lpr: HP-LaserJet-2200: unknown printer
I have added my user name to the lp and lpadmin groups. Trying the above as 'sudo' results in the same result. The only thing I've noticed is that when printing something from OpenOffice, in the document print status I get the message 'Processing - not connected?', although printing still works.
-- System Information:
Debian Release: squeeze/sid
APT prefers testing
APT policy: (500, 'testing')
Architecture: amd64 (x86_64)
Kernel: Linux 2.6.32-5-amd64 (SMP w/2 CPU cores)
Locale: LANG=en_NZ.UTF-8, LC_CTYPE=en_NZ.UTF-8 (charmap=UTF-8)
Shell: /bin/sh linked to /bin/dash
I am wondering if it is possible turn off my display with a key of my laptop's keyboard. I mean if I press ctrl + o then my display turn off and then if I press ctrl + o my display turn on.
After updating and subsequently restarting today, I can no longer bring up my wireless interface:
ifup wlan0
SIOCSIFFLAGS: Unknown error 132
Could not set interface 'wlan0' UP
SIOCSIFFLAGS: Unknown error 132
SIOCSIFFLAGS: Unknown error 132
Failed to bring up wlan0
iwconfig
lo no wireless extensions.
eth0 no wireless extensions.
wlan0 IEEE 802.11abg ESSID: off/any
Mode: Managed Access Point: Not-Associated Tx-Power=off
Retry long limit:7 RTS thr: off Fragment thr:off
Encryption key:off
Power Management:off
lsmod | grep iwl
iwl3945 77904 0
iwlcore 127432 1 iwl3945
mac80211 180929 2 iwl3945, iwlcore
cfg80211 142905 3 iwl3945, iwlcore, mac80211
My system goes through slow periods where it just crawls and others where it's fine, but I'm wondering which service settings are OK to just shut off to give me a bit more oomph when I boot up.The others I'm pretty OK with like spam assassin, dictionary server and so on, but some of the others i wonder if they only serve to slow things down..Also..I live in a very dusty environment and I KNOW the fans and other parts get caked with dust and it wouldn't surprise me if the dust got so bad it just stops the fans completely so once in a while I use my air compressor to blow the crud out and I usually get covered myself, but how safe is using the compressor? It's not the type that typically fills up with condensed water droplets so that isn't a super critical issue..It's a small 1 hp deal, elect drive and so on.. Safe enough? It's all I have and/or can afford..
View 1 Replies View RelatedIs there a command line tool to shut off/spin down the hard disk either when not in use or when something is typed into the console? I'm trying to save power in a laptop I have..
View 2 Replies View RelatedGnome-disk-utility doesn't show filesystem type, mount point, filesystem label, size¦ of my / filesystem.
I am running Debian Squeeze using lvm2. I have two HDDs and each has one primary partition, which are used as PVs. Having two VGs, each VG has it's own PV.
There are some LVs and all of them except the LV holding the swap space are formatted with XFS. Now gnome-disk-utility shows everything about my /home LV, another LV containing a whole Ubuntu installation,¦ only the / LV (and Swap LV, but I don't know what it is supposed to show there) is/are missing nearly all information.
Otherwise the system is running perfectly well and the Debian / LV is shown normally in Ubuntu's disk-utlity, as well as all other LVs.
fdisk
Physical volume
Volume group
Volume group
lvdisplay
Logical volume
Logical volume
Logical volume
Logical volume
Logical volume
DebianCopy is a copy of my Debian installation (different fs label and UUID). DebianII (again different UUID and label) is a copy too, but there I tried out newer (testing) versions of udisks/lvm2/udev and right after the upgrade it showd everything as it should with the additional advantage of the newer udisks-version showing my VGs, but after a reboot it showed the same behaviour as before or even worse, because the information about other LVs was missing too.
In the end I even modified the fstab. Originally it contained the /dev/mapper/vgbay... entries and I replaced them with LABEL=... and finally with UUID=..., but it didn't make any difference either.
When I watch any video on YouTube my screen will turn off (no HDMI connection) and then it will turn on after a couple seconds (10 -40 seconds). When I played Borderlands 2 the screen is completely fine.
View 10 Replies View RelatedI update Jessie "stable" 8.2 to 8.4 and now I get 5 minute interval kernel messages:
Apr 18 06:39:52 OraHost kernel: [131985.494726] sdc: unknown partition table
Apr 18 06:45:03 OraHost kernel: [132295.755942] sdc: unknown partition table
Apr 18 06:50:03 OraHost kernel: [132595.946564] sdc: unknown partition table
Apr 18 06:55:13 OraHost kernel: [132906.139327] sdc: unknown partition table
Apr 18 07:00:23 OraHost kernel: [133216.340555] sdc: unknown partition table
I believe this has something to do with an mdadm update which was included in the release. When I configured the array, I didn't partition the disk devices, so maybe that has something to do with it. I am thinking of rebuilding the array and partitioning prior to build, but a quick fix would be referable.
And also something appears to have happened to the raid device since the update.
Prior to update, the array was /dev/md0 - now it is /dev/md/0 which is a symbolic link back to /dev/md0.
mdadm --detail --scan now reports /dev/md/0 where previously it reported /dev/md0
I created a new RAID1 array on a fresh system and immediately after the create, these messages appear at 5 minute intervals.
I decided to update all the software on my computer. Fortunately, it upgraded kernel version 3.14 to 3.16. I was happy to learn that suspend now worked on my laptop by calling pm-suspend, but it did not worked by closing the lid. So I search and found on debian's website that installing systemd and adding some config lines in /etc/systemd/logind.conf would sove the issue. So I followed the procedure and did like instructed, to end up with a computer that boots on black screen.
The last verbrose line I see on boot up is "kvm disabled by bios" and then it shutdown down the screen. The computer works, as I can login and shutdown by doing those operation blindly.
I tried removing systemd but it still does not work. If I use the old kernel 3.14 I can boot without any problem, but if I use kernel 3.16, I boot to a black screen. I remember successfully booting in 3.16 before installing systemd.
My card Wifi network doesn't turn on, even at loading configuration of the system is failed. I have to wait a long time until the system itself to load.
And when I write ifconfig or iwconfig is displayed in the console interface wireless card.
And when I come in the panel on the network card, it immediately pops up a window that you can not load the network card modules.
I don't know what could have happened, I do not recall that I recently messed with the system.
Here are the pictures: [URL]....
And here I join dmesg.log file, at the end of a failed: [URL] ....
I have linux mint 17 quiana cinnamon
I am doing the DNS configuration for the first time. Error in named configuration:
zone localdomain/IN: loaded serial 42
zone localhost/IN: loaded serial 42
zone 0.0.127.in-addr.arpa/IN: loaded serial 1997022700
file1:9: unknown RR type 'example.com.'
file1:11: unknown RR type 'red.exmple.com.'
zone example.com/IN: loading master file file1: unknown class/type
[Code]....
I changed the first line of /etc/fstab in an attempt to get rid of an annoying message "mount: unknown filesystem type 'static'". All I did was put a "#" on the first line .... changing the original from:
# /etc/fstab: static file system information.
#
# <file system> <mount point> <type> <options> <dump> <pass>
to:
#
# /etc/fstab: static file system information.
#
# <file system> <mount point> <type> <options> <dump> <pass>
I have tried desperately to get to the file system so that I can edit that first line in fstab out but nothing works and the file system comes up as read only ...
I dont know anything about linux and just been assigned to amount a drive to it. here's what i did so far: Version of Linux using Red Hat Enterprise Linux Server release 5.3 (Tikanga) [root]# mount -t auto /dev/sdb1 /tmp/archive mount: unknown filesystem type 'ntfs'
when checking the /proc/filesystems, i noticed that 'ntfs' is not listed there, several forum suggested i try running 'modprobe ntfs'. If that is not found, you'll need a kernel with ntfs support. i'm so lost, where to i get the modprobe ntfs
How can I tell emacs that a file type that it doesn't recognise should have the same syntax highlighting as one it does?
Xfig produces .pstex files which I want to be highlighted like .ps/.eps
A formerly working system now gives an 'error 17' at Grub instead of booting. Here are the facts I have gathered thus far.
$ blkid
n/a (no output)
$ sudo fdisk -l /dev/sda
Code:
Disk /dev/sda: 60.1 GB, 60060155904 bytes
255 heads, 63 sectors/track, 7301 cylinders
[Code]...
i am trying to compile kernel 2.6.23 on Fedora 12 After fixing a few bugs (getline error, %dil ,etc) i was able to compile the kernel made initramfs img using dracut updated grub and then booted up the new kernel 2.6.23 but it fails to boot with following error mount: unknown filesystem type 'ext4'
View 8 Replies View RelatedWhile trying to solve the problem indicated in another thread [URL] .... I realised that I do not have the file /etc/X11/xorg.conf.
Also, if I enter the command Code: Select allsudo kate I get
Code: Select allcannot connect to X server :0
I tried logging in to another terminal (tty3) and entered
Code: Select allstartx
Kate opened normally with root permissions.
Currently I have a Nvidia card but I am using nouveau drivers.
My question is: installing the Nvidia drivers (following the guide in [URL] .....) would fix these Xorg issues?
I had troubles with nvidia drivers in other distros....
i've installed debian 8 on this laptop but can't use the nvidia card from nvidia-detect can't find the card but it work 'cause i can see it in the list of hardware, 3d controller the driver from nvidia don't work, and i had a problem with force installation and xorg.conf file.. how i can make it work ? the card it's nvidia 820m
View 3 Replies View RelatedI recently installed Squeeze. I had sound with the video driver that came with the install. Then I installed the Nvidia driver from Nvidia website. The sound dissappeared. When I uninstalled the Nvidia driver and removed xorg.conf and rebooted again, the sound came back. Then I installed the Nvidia driver from (nvidia-glx, dev and settings) from Debian with Synaptic. The sound went away again. If I uninstall the nvidia driver and xorg.conf the sound will probably come back again. The sound driver is the one that came with the install.
The volumes are unmuted in the alsamixer. Somehow alsaconf command does not work.
My mother board is a ASUS M4N78 Pro with Nvidia IGP.
What can I do to have sound with the nvidia driver?
I am on squeeze with kernel 2.6.32-3-amd64 and I have installed nvidia driver :cat /proc/driver/nvidia/version NVRM version: NVIDIA UNIX x86_64 Kernel Module 190.53 Wed Dec 9 15:29:46 PST 2009 GCC version: gcc version 4.3.4 (Debian 4.3.4-8)
View 1 Replies View RelatedI just updated Fedora 14 with the updates it downloaded and I am now stuck with the error.
View 10 Replies View Related