After updating and subsequently restarting today, I can no longer bring up my wireless interface:
ifup wlan0
SIOCSIFFLAGS: Unknown error 132
Could not set interface 'wlan0' UP
SIOCSIFFLAGS: Unknown error 132
SIOCSIFFLAGS: Unknown error 132
Failed to bring up wlan0
iwconfig
lo no wireless extensions.
eth0 no wireless extensions.
wlan0IEEE 802.11abg ESSID: off/any
Mode: Managed Access Point: Not-AssociatedTx-Power=off
Retry long limit:7RTS thr: offFragment thr:off
Encryption key:off
Power Management:off
i am wanting to turn my Debian box into a wireless AP, but for some unknown reason the wireless card won't switch into master mode when i run the command #iwconfig wlan1 mode master i get this Error for wireless request "Set Mode" (8B06): SET failed on device wlan1 ; Invalid argument. what does this mean and what do i need to configure/install to get it to work my wirless card is supported i checked it's a zydas chipset using the zd1211rw driver SMC EZ Connect SMCWUSB-G [URL]
Whenever I try to change a user full name, through System / Administration / Users and Groups, I get the following error: The configuration could not be saved - An unknown error occurred. Running Ubuntu 10.04.1 LTS 64 bit, freshly installed.
I am trying to manually configure my wireless interface similar to how I manually configure my wired interfaces on Ubuntu 10.10 (Maverick Meerkat). I have two wired interfaces that use static IP addresses. I set up these interfaces using /etc/network/interface file. I disabled network manager (it was never working correctly to start with). Now, I want to connect my wireless interface (wlan0) to an unsecured wireless private network. I know/can find out all the information about the wireless network (ssid, etc). Also, I need to do this without disconnecting either of my wired interfaces.
I have looked all over the internet/forums for information about how to set up this interface, but nothing I found meets my need. Is there any way I can use iwconfig or the interface file to connect to this wireless connection? Or is there any other tool that will allow me to manually do this?
I recently installed office 2007 under wine, but since I have it no longer know what to open .doc or .xls files with, I was using Gnumeric but now when i go to Properties -> "Open with" there is no longer anything in the list and even when i attempt to add to the list nothing comes up. If anyone know what way you can manually add file types and associate them with programs
It's been a while since ive run any Linux OS, but after reading about Osuse, i decided to partition my drive and check it out. Just downloaded and installed OpenSUSE. I have access to internet via my hard wired lan port, but wireless has me confused. Dell D600.I have allowed all updates to install, and added my wireless connection using KDE Control module. When i hit the scan button the scan box appears but nothing is picked up. My router is linksys, and its wide open (no encryption, nor hidden).
I have a laptop Compaq cq60 and once I installed opensuse 11.1 64 with a Atheros AR5001 wifi card (pci). It worked and connected to several wap at home and abroad with no problem. I upgrade the laptop with a clean install to OpenSuSE 11.4 (also x86_64).Now when I try to bring the interface up a strange message appears. Moreover! I had the same problem with a Netgear usb wifi dongle!A Realtek completely different chipset. Before the problems a small explanation of the setup.
The module for the Atheros is loaded with no problems.I already tested rmmod ath5k and rmmod ath and then modprobe ath5k ... no problems whatsoever.The same happens for the NetGear usb wifi dongle! It is immediately recognized as soon as the module is inserted and the module loaded.I also checked this with lsudev and lshal ... I could not see any problems there ... I do not use NetworkManager as my experience tells me it is better to first configure on cli and then move to the graphical interface when things are working conveniently.
So both internal and usb wifi cards are detected and the respective modules loaded with no problems.They are both configured in yast to be activated manually and they both have the wep key and essid. I connect to a Asuswl500g WAP with wep encryption just to start.
When I try to bring up any of those wifi interfaces I get this error :
I have installed an HP LaserJet 2200 network printer using CUPS successfully and can print test pages and stuff from OpenOffice, Evince etc. But no luck printing from lpr. Using lpstat seems to suggest all is well:
$ lpstat -t scheduler is running system default destination: HP-LaserJet-2200 device for HP-LaserJet-2200: socket://192.168.10.42:9100 HP-LaserJet-2200 accepting requests since Tue 19 Oct 2010 14:01:50 NZDT printer HP-LaserJet-2200 is idle. Enabled since Tue 19 Oct 2010 14:01:50 NZDT Ready to print.
If I now try to print 'test.txt' using: $ lpr test.txt nothing happens. Try calling the printer by name: $ lpr -P HP-LaserJet-2200 test.txt lpr: HP-LaserJet-2200: unknown printer
I have added my user name to the lp and lpadmin groups. Trying the above as 'sudo' results in the same result. The only thing I've noticed is that when printing something from OpenOffice, in the document print status I get the message 'Processing - not connected?', although printing still works.
I installed Debian 5.04. The Debian installer picked the Ethernet card but not the wireless (Atheros 9285). I followed these instructions to install it (found at [URL]...
[code]...
But there was no wireless interface shown in the network interfaces entry of hardinfo, even though I wrote modprobe ath_pci in terminal window. My questions are: 1. I followed the instructions regarding updating the madwifi sources, installing them etc. Does this guarantee that apt downloaded and installed the right madwifi driver? 2. Will I be better off if I try to install the driver downloaded from the Atheros website? 3. How can I activate the wireless interface (since the driver is running should not the wireless interface somehow show up automatically)? 4. When I am running Ubuntu 9.10 it picks up the wireless. Can I somehow copy all the files for the wireless from Ubuntu and paste them in the Debian filesystem?
I'm having problems installing Ubuntu 10.10 Netbook onto my Asus 900. I downloaded the .iso then used the "make startup disc" feature in my Mint 9 desktop machine to make a usb install disk. All appears well at that point. When I try to boot from the usb stick, I get an error message as follows:
I have b43 wireless. In network Configuration on system->administration the interface it appears as inactive it appers in hardware also as b43 associated to wlan0 but i cannot have access to any wireless network. What i have to do to put this b43 to work.
on my dual HD5500/GT940M. I can not turn on Nvidia. just install bumblebee and got the error "unknown header type 7f" if I remove bumblebee, Nvidia 340 loaded but system run on HD5500, no way to use Primus or to switch to 2nd card.
Gnome-disk-utility doesn't show filesystem type, mount point, filesystem label, size of my / filesystem.
I am running Debian Squeeze using lvm2. I have two HDDs and each has one primary partition, which are used as PVs. Having two VGs, each VG has it's own PV.
There are some LVs and all of them except the LV holding the swap space are formatted with XFS. Now gnome-disk-utility shows everything about my /home LV, another LV containing a whole Ubuntu installation, only the / LV (and Swap LV, but I don't know what it is supposed to show there) is/are missing nearly all information.
Otherwise the system is running perfectly well and the Debian / LV is shown normally in Ubuntu's disk-utlity, as well as all other LVs.
fdisk
Physical volume
Volume group
Volume group
lvdisplay
Logical volume
Logical volume
Logical volume
Logical volume
Logical volume
DebianCopy is a copy of my Debian installation (different fs label and UUID). DebianII (again different UUID and label) is a copy too, but there I tried out newer (testing) versions of udisks/lvm2/udev and right after the upgrade it showd everything as it should with the additional advantage of the newer udisks-version showing my VGs, but after a reboot it showed the same behaviour as before or even worse, because the information about other LVs was missing too.
In the end I even modified the fstab. Originally it contained the /dev/mapper/vgbay... entries and I replaced them with LABEL=... and finally with UUID=..., but it didn't make any difference either.
I'm renting a server which comes with 5 IP addresses, but only one network device. From what I can understand I'm able to create aliases by adding entries to /etc/networks/interfaces, I haven't tried I'm in the planning stages. Hypothetically, 192.168.22.30 is my primary IP and I want to set eth0:1 to have 192.168.22.31, and then after that I want to create a virtual machine (using kvm/qemu) that is able to communicate bidirectionally to the internet over eth0:1, and leave eth0 strictly for administrating (not for VM traffic).
The qemu guides I'm finding seem to assume that I want to use TAP or VDE, what I want to use is a sub-ip/alias. One guide I saw had me eliminate everything from eth0 and put it under br0. That would leave me unable to ssh into my server (and unable to administrate). Is there a way I can do something along the lines of: qemu [options] -net [option] -netdev=eth0:1 ?
Is is possible, via iptables or something similar, to bind a service running on a specific port to a specific interface? My case: I use a VPN service for privacy. I would like to have all traffic except ftp and ssh to run over tun0. Ports 21 and 22 will need to be accessible to the outside world (eth0) while the VPN is running.
I believe this has something to do with an mdadm update which was included in the release. When I configured the array, I didn't partition the disk devices, so maybe that has something to do with it. I am thinking of rebuilding the array and partitioning prior to build, but a quick fix would be referable.
And also something appears to have happened to the raid device since the update.
Prior to update, the array was /dev/md0 - now it is /dev/md/0 which is a symbolic link back to /dev/md0.
mdadm --detail --scan now reports /dev/md/0 where previously it reported /dev/md0
I created a new RAID1 array on a fresh system and immediately after the create, these messages appear at 5 minute intervals.
Suppose I have both a hardwired and a wireless network connection active on the same system at the same time. Can I tell my browser which one to use? Can I tell other programs which one to use? Or do they choose for themselves> Or does some automatic system protocol select which one to use for them?
I am having some troubles using iptable rules on two Servers that act as Gateways pointed to one backend server with only one interface.
To be more exact, i have 3 Servers, 2 of those have a public and a private interface, with different public ips but common private interface ( they connect to the same switch ), the last one only has 1 private interface and is connected to that same switch.
Those 2 servers also act as a gateway and a firewall for the private network.
My problem is that i cannot seem able to route traffic from both of those to the third one and back to the same public ip that the request came from ( effectivly using two gateways on the machine with only one interface ).
As a testing scenario i am using ferm for applying iptable rules that forward ssh traffic ( for example ) to the backend server, and it works well when i do it with one gateway.
When i apply something like this in /etc/network/interfaces on the backend server though:
Even though forcing selection of an interface from the backend server ( like curl --interface ) seems to work well, meaning that the request to the curl appear to happen from the correct public ip, i can still only use one of the public ips to access the server with the ferm rules. Ideally i should be able to ssh to the backend server from both public ips using their ferm rules for forwarding traffic to the backend server.
I feel like i am missing some details on routing that should happen on the firewalls as the backend server seems to be able to use both gateways to access the internet and receive replies from it.
If I comment those off then no such problem, hence some how ppp0 executed automatically and there is no [auto ppp0] any where. How can I stop this forcefully ?
I am running Debian Squeeze on an old pc (AMD K62-500) which serves as my multiwan router and torrent box. Internet uplink is provided via a dsl line and 2 wireless canopy modules.
Setup has been generally fine except when connecting/downloading as free user from sites like rapidshare, hotfile, filesonic, etc. The problem arises when I am connected to these sites using the wireless uplinks because of the shared public ip. I don't really download that much using direct download methods so I don't really see myself being a premium user from these sites.
If these sites are on a specific ip or ip range, an entry on the static routing table would have been fine but when I tried using ping, a different ip would appear to reply each time.
I wonder if there can be a solution like using iptables where in traffic to and from these sites will only use the NIC connected to the dsl line.
I want to configure multiple virtual ethernet interfaces over a single physical ethernet interface (eth0) and for each virtual interface the MAC address must be unique and the IP address must be Static.Finally all the virtual interfaces must be able to communicate both internally and externally and the traffic should be captured using wireshark.
I need to have such kind of setup to communicate devices individually using one physical ethernet device.
Because I was fiddling with few kernel modules like MACVLAN and MACVTAP and successfully enabled those modules and rebuild kernel. Using macvlan and macvtap I can configure virtual interfaces with unique mac address and static IPs but while capturing packets using wireshark interfaces behave weirdly.
For example say on HOST machine I have 1 physical interface and created 3 virtual interfaces as shown below.
First from above interfaces I started pinging eth0 internally from host machine in which it worked as usually.
Second I did same externally from other machine which is connected to the same network of Host machine, and this did work as usually.
Third I pinged first virtual interface veth0 both internally and externally and this also works and after that I did check source and destination MAC address using wireshark tool-where both showed up there respective MAC address.
Now triggers the issue, where I pinged second virtual interface same like I did for first one, but this time ping was success and where as in wireshark tool the MAC address for veth0 is picked by veth1. This is where I got stuck and this issue happened for all the remaining virtual interfaces.
I couldn't see any virtual interface showing their respective MAC address, as of the remaining except the first virtual interface has been picking the first veth0 mac address.
I have a problem with Transmission. After using it for over six months without a single problem, it suddenly stopped downloading. In the torrents that do no get downloaded, I get an error message Tracker responded: Unknown error (0) in the info window, tracker tab. But there are torrents with the same tracker that don'thave a problem and get downloaded fineThe logs don't give a clue about whats wrong either.I tried downloading those torrents with Vuze and I had the same problem. What could be wrong?
I'm running Debian testing and after a recent software update, suddenly I can no longer boot into my single Linux kernel image anymore. I did look at the software update before I did it and I don't believe that it removed any software packages. When I try to boot into my linux 2.6.26-1-amd64 image, I get the following message from grub:"error: unknown command `initrd'"..The same error appears if I try to boot into single-user mode. I have a Windows XP partition on the same hard disk and I am still able to boot into that from grub. I've searched the net and haven't really found my same problem replicated anywhere. I would imagine that the problem is just that somehow the initrd package got removed in my last software update, but again I don't recall seeing any software that the update planned to remove.
Any thoughts on how I would go about fixing this problem? Since I'm unable to get into Linux at all, I imagine I'll have to use a LiveCD to get in and fix the problem, but I don't know where to begin looking.
