Debian Configuration :: .doc And .xls Unknown File
Sep 29, 2010
I recently installed office 2007 under wine, but since I have it no longer know what to open .doc or .xls files with, I was using Gnumeric but now when i go to Properties -> "Open with" there is no longer anything in the list and even when i attempt to add to the list nothing comes up. If anyone know what way you can manually add file types and associate them with programs
recently got this message when USB booting:Unknown keyword in configuration file: gfxbootI used to have the "Unknown keyword in configuration file: ui" problem, which was spread throughout the forum. I know people have fixed it by removing the "ui" in the config file. This is what I did in /syslinux/syslinux.cfg
# D-I config version 2.0 include menu.cfg default vesamenu.c32
I have installed an HP LaserJet 2200 network printer using CUPS successfully and can print test pages and stuff from OpenOffice, Evince etc. But no luck printing from lpr. Using lpstat seems to suggest all is well:
$ lpstat -t scheduler is running system default destination: HP-LaserJet-2200 device for HP-LaserJet-2200: socket://192.168.10.42:9100 HP-LaserJet-2200 accepting requests since Tue 19 Oct 2010 14:01:50 NZDT printer HP-LaserJet-2200 is idle. Enabled since Tue 19 Oct 2010 14:01:50 NZDT Ready to print.
If I now try to print 'test.txt' using: $ lpr test.txt nothing happens. Try calling the printer by name: $ lpr -P HP-LaserJet-2200 test.txt lpr: HP-LaserJet-2200: unknown printer
I have added my user name to the lp and lpadmin groups. Trying the above as 'sudo' results in the same result. The only thing I've noticed is that when printing something from OpenOffice, in the document print status I get the message 'Processing - not connected?', although printing still works.
After updating and subsequently restarting today, I can no longer bring up my wireless interface:
ifup wlan0 SIOCSIFFLAGS: Unknown error 132 Could not set interface 'wlan0' UP SIOCSIFFLAGS: Unknown error 132 SIOCSIFFLAGS: Unknown error 132 Failed to bring up wlan0
iwconfig lo no wireless extensions. eth0 no wireless extensions.
wlan0IEEE 802.11abg ESSID: off/any Mode: Managed Access Point: Not-AssociatedTx-Power=off Retry long limit:7RTS thr: offFragment thr:off Encryption key:off Power Management:off
on my dual HD5500/GT940M. I can not turn on Nvidia. just install bumblebee and got the error "unknown header type 7f" if I remove bumblebee, Nvidia 340 loaded but system run on HD5500, no way to use Primus or to switch to 2nd card.
Gnome-disk-utility doesn't show filesystem type, mount point, filesystem label, size of my / filesystem.
I am running Debian Squeeze using lvm2. I have two HDDs and each has one primary partition, which are used as PVs. Having two VGs, each VG has it's own PV.
There are some LVs and all of them except the LV holding the swap space are formatted with XFS. Now gnome-disk-utility shows everything about my /home LV, another LV containing a whole Ubuntu installation, only the / LV (and Swap LV, but I don't know what it is supposed to show there) is/are missing nearly all information.
Otherwise the system is running perfectly well and the Debian / LV is shown normally in Ubuntu's disk-utlity, as well as all other LVs.
fdisk
Physical volume
Volume group
Volume group
lvdisplay
Logical volume
Logical volume
Logical volume
Logical volume
Logical volume
DebianCopy is a copy of my Debian installation (different fs label and UUID). DebianII (again different UUID and label) is a copy too, but there I tried out newer (testing) versions of udisks/lvm2/udev and right after the upgrade it showd everything as it should with the additional advantage of the newer udisks-version showing my VGs, but after a reboot it showed the same behaviour as before or even worse, because the information about other LVs was missing too.
In the end I even modified the fstab. Originally it contained the /dev/mapper/vgbay... entries and I replaced them with LABEL=... and finally with UUID=..., but it didn't make any difference either.
I'm having problems installing Ubuntu 10.10 Netbook onto my Asus 900. I downloaded the .iso then used the "make startup disc" feature in my Mint 9 desktop machine to make a usb install disk. All appears well at that point. When I try to boot from the usb stick, I get an error message as follows:
I believe this has something to do with an mdadm update which was included in the release. When I configured the array, I didn't partition the disk devices, so maybe that has something to do with it. I am thinking of rebuilding the array and partitioning prior to build, but a quick fix would be referable.
And also something appears to have happened to the raid device since the update.
Prior to update, the array was /dev/md0 - now it is /dev/md/0 which is a symbolic link back to /dev/md0.
mdadm --detail --scan now reports /dev/md/0 where previously it reported /dev/md0
I created a new RAID1 array on a fresh system and immediately after the create, these messages appear at 5 minute intervals.
I have some errors when run the mount -all command: mount: wrong fs type, bad option, bad superblock on /dev/sdc5, missing codepage or helper program, or other error In some cases useful info is found in syslog - try dmesg | tail or so Failed to open /proc/filesystems: No such file or directory
There is this bug in the latest version of Ubuntu, which is also Jessie, which is:
Can't copy a file from SMB share to the local file system: Software caused connection abort
The problem, apparently, is that newer versions of Samba hit servers with multiple requests at the same time, and for some reason the Zyxel and Iomega boxes can't handle this. The best solution they've come up with is to modify the smb.conf file on your server to include this setting: "max mux = 1".
Here is the reference material on this bug: [URL] ....
People who develop samba have fixed it in the latest version but neither the ubuntu nor Debian have released the fixed version of nautilus, as of yet. Here, is the reference: [URL] ....
I am trying to compile C source file to generate .trb file (turbo file) which will then burn on trubo sim using TP2. When I comiple the code following error is occuring. before going through belwo error I was getting error 'Unknown MCU atmega128', known MCU are: (list appread), then I change the configuration and set the MCU to supported list then following error is occuring.
I have an encrypted root and encrypted boot drive... To avoid entering a passphrase multiple times I'd like to add a keyfile for my root drive to my initrd... I've done this in Arch and it was relatively simple but I've hit a road block in debian finding the analog processes...
Code: Select all#Part 1) Generate the keyfile, give it suitable permissions and add it as a LUKS key:
I'm trying to resize tmp file using gparted. So I used gparted live cd and then i resized the tmp file but delete the old /tmp partition without backup. Now, my pc do not start. I have Debian 8.
I'm using Xfce 4.8, which now provides built-in samba browing in thunar. This works like a charm. I can browse a samba share (external HD connecter to router via USB). Yet it appears to me now that the support is limited to thunar. I mean double clicking on a file allows me to open/edit that file if and only if the software itself has samba support. In practice, double-clicking on a movie opens it with vlc thanks to vlc's own smb support. Even then, I can't find a way to add the subtitle file. I reckon that to use the share transparently, I would need to mount it the "mount" way. Either on a mount point like /mnt/hard_drive or something like .gvfs/hard_drive.
Is my understanding correct ? Is that my only option? Considering the disk won't be switched on at startup, fstab is not the solution. Would gigolo be the right choice? I spent some time trying gigolo a few days ago, following an easy tuto found on the web and it didn't work as expected. If needed I could give it another try.
Just installed fedora 14 and do not have a printer config app. Im not sure what packages should be installed. I just came back to linux after years off. Lots different from redhat 6.
I've been working on the setup of a FTP server on my Debian system for the whole afternoon. But I can't get it straight! Normally I get it working in just a second, but it's been a while I guess.
I installed only proftpd-basic and it's default dependencies. Should be enough right?
My configuration files are as follows:
I created the user zeitgeist, gave it a password, group and a homedir. Group of the user is nogroup and the homedir is correct with the 755 permission. My port 21 for FTP is open I tested it with nmap -p 21 [ip-address].
My Filezilla client tells me that at first he is connecting, then the connection is established, And then the connection is closed by server.
I am using Debian Lenny as my server to host multiple databases.
Whenever, I used to add a new database, I used to add an IP address like eth0:test in the /etc/network/interfaces file.
Today when I tried to do the same, I got an error when I tried to start the interface by typing "#ifup eth0:test". I also tried to do in this way "#ifconfig eth0:test up" but both of then yielded the same error saying "/sbin/ifconfig: no such file or directory".
The path is valid and the files are also present there. There are ifup, ifdown, if and ifconfig files in the /sbin directory. I also checked the permissions which is root:root. But still I cannot find the problem.
I am running debian lenny running apache (latest) i am trying to make a webserver. i put the index.html file in my www folder. it shows up when i go to my site (localhost) i put an index.php file in my www folder and when i try to go to my site it Downloads the index.php file instead of showing it.
I have 2 windows pc's in my home and an office computer that have my files strewn about. I wanted to have them all in one central location that keeps a backup copy, so i used an old machine to start building a file server. I installed debian 5.0 on the machine, command line interface only. I have gotten ssh working so that i can do all my work on the box from one of my windows pc's by logging in with putty.my current problem is how to easily use the box hard drive for storing my files in an easily accessible way. i'm still working on getting samba to work so that i could map the /home directory to a drive letter on my two home pc's, but i'd also like to access files from my work pc. Before i do that, though, i wanted to know if this is safe and secure to map a drive on a remote machine through the internet? Are there any other security concerns I need to be addressing by having this file server set up?
I'm developing with puppet, and I need to do an aptitude update from a specific file, here is my configuration: The file sources.list in /etc/apt/ is deleted. I've created 3 files in /etc/apt/sources.list.d each one with their repos:
00-debian_sources.list deb http://ftp.fr.debian.org/debian/ lenny main contrib non-free deb-src http://ftp.fr.debian.org/debian/ lenny main contrib non-free
[code]....
All the repos are updated/refreshed , and I only want to refresh/update the specific repos insie of the file 01-debian_security_updates.list. On the other hand if I put some repos in the sources.list and delete the 3 files and I create an external file for example in /tmp/temprepo and I do the command aptitude update -o dir::etc::sourcelist=/tmp/temprepo it works fine.give some workaround to update and then upgrade packages from the files specified in my config.
Today I decided to include again Debian Volatile and discovered that it doesn't exist anymore and that I can get the same packages using this line: deb [url] squeeze-updates main
And the first question is: is this the same than debian-security?
Then, I decided to use [url] to make things less confused, and this was the output:
The first line is Ok. The second line, I guest it's the same than my second line. But, the third, is something different. So, the main question is: what is the difference between squeeze-proposed-updates and squeeze-updates? Are those repos completely separated from squeeze/updates (in security.debian.org)? And, what else should I add to have an always up-to-date and secure system?
A recent update to Iceweasel 5 (version 5.0-6 ) on my debian (Linux xxxxx 3.0.0-1-amd64 #1 SMP Sun Jul 24 02:24:44 UTC 2011 x86_64 GNU/Linux) led to a rather odd an annoying behavior. Each time I try to open an external file (pdf, odt) or to save a file on the hard drive, then Iceweasel crashes systematically. Does anyone experience the same? Any idea of how to fix this?
I work in a compagny and i encounter a problem with the samba trash.When i delete a file from our network directory, the file don't move to the samba trash directory. But, the server create the same samba tree like the orginal file. It's more simple with a example.This is the file i delete to my samba tree S:departementgestion_informatiqueinformatiquecommut est.txt.This is the samba tree that the server create at the moment when i delete my file : @IPcorbeilledepartementgestion_informatiqueinformatiquecommun
The problem is here : We want the file test.txt into this trash tree and it isn't.This is the Samba trash configuration :
I am trying to configure samba for a stripped down file server. I am running debian with command line only. My problem is that I cannot unmask samba.
See below:
root@debian:/home/aaron# service samba status ● samba.service Loaded: masked (/dev/null) Active: inactive (dead)
I have tried "sudo systemctl unmask samba.service". I receive no errors however it does not actually unmask. I can't find anything online regarding a service stuck on masked status.
I've downloaded configuration files for my VPN, Kovurt, and they don't have a .ovpn file extension. Further, when I tried to enter the information manually (using this guide), I saw that the files only include the <ca> tags, and no <cert>, <key> or <tls-auth> tags.
Here is the content of one of the config files, simply named 'Tokyo' with no extension. (adding .ovpn didn't work either):
Code: Select allclient dev tun proto udp remote 50.31.255.86 443 resolv-retry infinite nobind
[Code] ....
I have an open ticket with Kovurt asking for the other info, but I know already that they don't have much in the way of documentation or support for Linux.
I have installed debian on my dell latitude d630 laptop and am currently making a derivative for others to use. however I can't get the wireless to work. I downloaded it from the broadcom site but it comes as a gzip file instead of a deb file. if I extract the gzip file I don't get any installable (deb) files. I need the wireless to work because now a bridged network from my windows laptop isn't working.
how can i do user2 can't get the file /home/user1/www/wp-config.php by using an editor but the webserver can?i mean how can i disallow access on other user's directorys but allow only one? (www-data in case).