I've bought a new e-sata external HDD. It work fine if it's connected throught USB. The problem goes when I connect it throught e-sata. The disk isn't detected (see the first screenshot).I must restart my computer to get the HDD detected (the HDD must be pluged in while booting, I think).Is it possible to repair that? I need the HDD to be detected immidiately when connected, like USB, without any restart.
View 1 RepliesI tried to install 11.04, but the partition tool shows no HDD. If I try to run Ubuntu from the CD, I can explore the HDD but the partition tool in the installation program won't find it. What can be wrong with my Promise SATA controller
View 8 Replies View RelatedI'm trying to install 10.04b2 x64 on my new rig and for some reason the live cd can't detect both of my 1TB Sata 3 drives. There is no Raid and the bios has them flagged as IDE. I have also tried adding pci=nomsi to the boot string to no avail.
View 8 Replies View Relatedused to run ARC linux and Windows 7 on my computer and i am now trying to install Ubuntu 10.10 X86_64When i used the live disc of Ubuntu 10.04 and load the installer it finds my four harddrive they way it should... sda,sdb,sdc,and sdd...When i however try the same with ubuntu 10.10 it displays my usb cardreaders drives first and then my hardrives as sde sdf sdg and sdh.I tried installing ubuntu with the reader unplugged and then reconnecting it after installation...But when i then boot with the reader attached it says it cannot mount drives sda,sdb,sdc and sdd becuase they are not ready.I think it is again detecting the usb cardreader before the sata controller ...Is there a way for me to alter the boot detection order so it will find my harddrives first and then the usb cardreaders ports ?
View 1 Replies View RelatedI have a i3 processor and MSI p55-cd53 motherboard. My problem is fedora cannot detect the 2nd SATA, so that I can configure raid1.
View 1 Replies View RelatedI have an issue with Hard Drives in GNU/Linux CentOS 5.3I installed linux 5.3 frash copy to new SATA MAXTOR 1000GB Hdd.And see the partitions is SATA MAXTOR 1000GB (NEW INSTALLATION CentOS 5.3)
/dev/sda1 Boot
/dev/sda3 /
(/dev/sda2 is the SWAP)
[code].....
I want to install Ubuntu 10.10 via a DVD-ROM but I faild. I got the message "no common cd-rom drive was detected." I have tried to install ubuntu 11.4 and failed too.
Hardware Setting:
DVD-ROM was attached to SATA 3.0 port.
SATA controller was set to IDE mode.
PCH is CougarPoint.
I use the same hardware setting to install Red Hat 6.0 and it works fine. I tried following boot option but in vain: noapic, acpi=off, nodmraid, all_generic_ide. It is ok to boot via a live usb but ubuntu 10.10 still can't find DVD-ROM. I have to use the hardware setting I descripted to install Ubuntu 10.10.
dmesg:
Code:
[ 1.892198] ata1: SATA max UDMA/133 cmd 0x3098 ctl 0x30ac bmdma 0x3070 irq 19
[ 3.309652] ata1.01: failed to resume link (SControl 0)
[ 3.469636] ata1.00: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[code]...
i'm using athlon 64 bit , asus a8vmx mbd, 1gb ram
View 3 Replies View RelatedI am trying to install Debian 5.0 "Lenny" on a PC with a very new hardware config (i3 processor, DDR3 RAM,LG SATA DVD drive, and Seagate SATA HDD). During the hardware detection phase of installation, I get a message saying the driver for my CD drive is not known, and asking me to select one manually. The options I get are only 'devcdrom', which does not work, and my installation cannot proceed.
I tried the following:
1. I read in a similar query that to use SATA DVD drives, I will have to set some boot options, so tried entering install libatapi_enabled=1 as an install option. This showed 'unknown parameter' error followed by same problem.
2. My Intel m/b BIOS has an option to set the DVD drive to "Native" or "Legacy", default is Native. I also tried changing this to "Legacy". Still same problem.
3. Read that I have to point to different drivers, but don't know how to do this during the installation.
I have a working F-10 box with an older motherboard (pre-sata). The p-ata ports are full (4 drives), so I'm trying to add a sata controller and another drive. The sata controller plugs into the pci bus, but is not detected by the bios (very old). After booting, the OS loads the driver module(s) and detects the new controller and drive. I was able to add the new sata drive into the LVM system using system-config-lvm. All was fine until I rebooted.
I get pages of lvm errors and booting fails. It looks like it's trying to mount the volumes before the sata controller is modprobed. Is there a way to get the os to modprobe for the new controller before trying to mount? The extra drive space is on a data partition, not the boot partition.
All of my computers are second-hand (except 1 laptop but it doesn't count) and I see in my Dell 4600 there are 2 SATA connectors on the motherboard. I picked up a 250 GB SATA hard disk and cables recently and tried plugging it in but the system doesn't see it. I even disconnected all other disks to make sure there wasn't a conflict (master/slave) issue going on but the system still does not see it.
The disk is vibrating so I assume it is getting juice and is spinning. Is there a setting or something I have to do to tell the system to access the SATA? Do I have to look at RAID settings if there is only 1 SATA disk? Can I not have a SATA disk and an ATA disk plugged in at the same time? I want to try and determine if the disk is bad, or is it PEBKAC!
I am trying to install FC4 in my pc having WDC WD800JD SATA HDD. During the installation it shows that no HDD found. I have searched a lot but no driver are found for fedora core 4.
View 10 Replies View RelatedI'm in rescue mode with Centos 5.2 disk trying to install/mount a new disk to extract data out from the failed server.
Plugged in a new SATA drive and syslog shows the drive being detected
SCSI device sdg: blah
sdg: Mode Sense: 00 3a 00 00
sdg: unknown partition table
sd 3:0:0:0: attached scsi disk sdg
However fdisk and mount does not find the drive. I tried echo "---" /sys/class/scsi_host/host3/scan based on one of the previous threads but get "write error: invalid argument".
how should I get the drive to be usable?
The hard disk is seen in the BIOS.
The partitions on it are accessible via the Places Menu on the Lucid Live CD.
It's just when I try to install, nothing is detected in Step 4 of 8, "Prepare Partitions".
An old 80GB IDE disk, on the other hand is seen by the partitioner.
I am not using RAID and it is not enabled in the BIOS.
I have a hardisk (seagte,80gb).I installed windows xp professional(60gb space) & Ubuntu 10.04(13 gb space)...Once a time i was in windows xp.after sometime it hanged.after waiting sometime. i press the key of reboot.after that one messege appeared "please select proper boot device & rebbot."then i went to my BIOS settings there i could not find my hardisk.I thought there is a bad sector in my harddisk.I went service center with my hardisk.After testing my hardisk they said no fault found.then I again installed XP & ubuntu & also replaced the hardisk cable.then after some day days I was on ubuntu.same thing occured(my pc getting hanged).& after rebooting manually my hardisk is not detecting...I am not clear..whatis the actual problem of my pc.
View 1 Replies View RelatedI bought a Rampage III Extreme Black Edition wich has a SATA III controller (Marvell 88SE9182). I try to install Fedeora Core 15, but FC15 just dont recognize any of my HDs placed in SATA III ports. Has any fellow succeed installing linux on this SATA Controller?
View 8 Replies View RelatedCan SATA 3 (SATA III) Hard disk be run on motherboard which only supports SATA II, except sacrificing the speed (throughput)?
View 2 Replies View RelatedI keep getting this error in my log viewer every 2 seconds: Code: ata4: limiting SATA link speed to 1.5 Gbps I have a dual boot SSD and I have run many SMART tests in windows and linux, (using smartmon tools and the disk utility) and the reports are all 100% healthy..... My research shows that this error represents one of the following:
1. Problem with SATA controller
2. Changing BIOS to allow SATA
3. Changing SATA mode to PATA or AHCI
4. Replacing the SATA cable
5. Allowing the SSD to run at SATA II speeds, i.e. 3 Gbps
- Does anyone know how to try number 5, i.e. allowing the SSD to run at SATA II speeds? I am lost here and this problem has caused my machine to crash twice when watching a movie in linux/ ubuntu. (It is worth noting that the crashes have only occurred in linux and I have never had an issue in windows, so it does seem to be a linux setting somewhere, hence why I think it is a "allowing SATA II to run at correct speeds issue")
I have fake(bios) raid0 with Windows XP and third non-raid hd which I wanted use to install linux to (as I read about problems with installing grub into raid0). During installation Yast had correctly detected raids and all windows partitions (basically its divided into two raids with 2 partitions of 1st and 3 on 2nd) and even proposed mounting them at /windows/c, /windows/d and so on. Now I have OpenSuse 11.4 installed, grub at /boot on sdc but to log to system I need to use installation disc (otherwise Windows starts up). What I wanted to do is follow this tutorial to add grub to Windows bootloader: Boot Multiboot openSUSE Windows (2000, XP, Vista - any mix) with Windows bootloader. Problem is after reboot partitions are not mounted (dirs exists but nothing there) so I cannot copy boot code to windows. I read that fake raid may need special drivers but when i start Yast->system->partitions it again shows everything correctly!
fragment from partitions section in Yast (I translated/removed non-important entries as I have non-English system so it may vary from what is actually in Eng version):
Code:
Device: /dev/md125p1
Size: 48.83 GB
Device path:
[Code].....
In our company, we have one server with kernel, 2.6.18. because of our neads, we had to buy new hard disk,that slax live cd detects that as "Ibex Peak 2 port SATA IDE Controlle".Apparently this kernel does not support this device.Unfortunately according to our policy(definitely some dependency on company's softwares installed on this kernel) we can not upgrade our kernel.
View 1 Replies View RelatedI installed Ubuntu 10.04, and happened to have an Silicom Images PCXpress card plugged in, and it kindly added the sil_sata module.This is fine for this chip set.I think that my earlier installation of Ubuntu 9.04 used Libata, which does support NCQ and also has good legacy support for the Intel Intel ICH7 chipset I have inside my Sony Vaio SZ notebook. Also, libata also support Silicon Image chipsets as far as I can tell from URL...I wish to remove the Silicom Images SATA modules and replace this with libata and then test the performance between the two device drivers.
View 5 Replies View RelatedMy motherboard supports SATA but I do not know which version: SATA-I or SATA-II. I want to buy a SSD so it would be pointless to buy a fast SSD if my motherboard only suports SATA-I
View 7 Replies View Relatedubuntu 8.04 server can not detect seagate sata hard drive 2tb or sata Lg dvdrw x22 sata drive .is it possible to install it without buying a pci ide sata card?is it possible to get a driver for sata driver and sata drive that can be recognise by ubunto 8.04 server ?or to get the files for 1.44 floppy diskdoes the late edition of unbutu recognise sate hdd and sata cdrw drive automaticly during the installation of the unbutu?
View 1 Replies View RelatedI have just finished the upgrade of the latest version and I'm at the point of my system restating.
My system automatically tried to restart but on the restart I got the 'terminal' view. It stopped when asking for my username (it never normally asks for this before the grub menu) and then password. I didn't get any further than that.
I now have on my screen (still in the terminal view before the grub menu)
"name@name-desktop:...$ "
I'm on my phone now so I don't actually have the symbol for before the dollar sign but your know what it is. The raised S on a 90 degree angle.
I have a suspend problem in my laptop. Sometimes, when resuming from suspend, the network adapter is down (that is, the network does not work and the light of the network adapter is off). Restarting the network service doesn't work, because I think that the system forgot about the hardware, and probably the driver should be reloaded.Does anyone knows how to do that?(ps. /etc/init.d/networking restart does not work, because the hardware driver is not being recognized anymore).
View 5 Replies View Relatedi have installed dhcp,there i declared the subnet and network,i used command include "/etc/dhcpd.conf.jutu1"; to start and other files, but it show me this error when i want to restart the DHCP, if you need more information contact me, i have configured this file too jutu1, but it don't let me to restart dhcp from /etc/init.d/dhcpd restart, this show me this message
[Code]..
Whenever I choose "Restart" from the GDM screen, GDM appears to shutdown, and the first TTY is displayed with a login prompt at the bottom (assuming I haven't used that TTY). I am by no estimation a patient individual, but I waited a solid minute or two for something to happen, but nothing ever did. I end up logging in as root on that TTY and running "shutdown -r now" to get the job done. This is a shared computer, and ideally any user should be able to perform shutdown options graphically from GDM.The only mentioned workaround doesn't apply to me as I am using the nvidia driver, not intel.
View 1 Replies View Relatedwhats the difference between restarting/stopping apache using 'service httpd restart/stop' and apachectl restart/stop. I know that using 'service httpd restart' is actually a script in /etc/init.d/httpd but what about apachectl?
View 1 Replies View RelatedMy friend bought an old hard drive. He noticed something with the hard drive that it was just replaced with a SATA socket. So meaning, the SATA socket was soldered to the PATA hard disk to replace the PATA socket to SATA socket to make it a SATA.
Now the question is:
1. Does the Transfer Rate of the harddisk (that has been replaced from PATA socket to SATA socket) would be SATA transfer rate? OR would still be PATA transfer rate?
I have this SATA drive, which I want to connect to my usb drive. Its installed with Ubuntu 10.04. I want to connect it to my laptop using a "SATA to USB connector" and then boot linux. So before I buy this connector/adaptor, can I know if it can be booted from USB?
Note: My laptop is loaded with Windows7.