Debian :: SATA DVD Drive Not Detected During Lenny Install?
Nov 17, 2010
I am trying to install Debian 5.0 "Lenny" on a PC with a very new hardware config (i3 processor, DDR3 RAM,LG SATA DVD drive, and Seagate SATA HDD). During the hardware detection phase of installation, I get a message saying the driver for my CD drive is not known, and asking me to select one manually. The options I get are only 'devcdrom', which does not work, and my installation cannot proceed.
I tried the following:
1. I read in a similar query that to use SATA DVD drives, I will have to set some boot options, so tried entering install libatapi_enabled=1 as an install option. This showed 'unknown parameter' error followed by same problem.
2. My Intel m/b BIOS has an option to set the DVD drive to "Native" or "Legacy", default is Native. I also tried changing this to "Legacy". Still same problem.
3. Read that I have to point to different drivers, but don't know how to do this during the installation.
View 1 Replies
ADVERTISEMENT
Oct 18, 2009
I have a working F-10 box with an older motherboard (pre-sata). The p-ata ports are full (4 drives), so I'm trying to add a sata controller and another drive. The sata controller plugs into the pci bus, but is not detected by the bios (very old). After booting, the OS loads the driver module(s) and detects the new controller and drive. I was able to add the new sata drive into the LVM system using system-config-lvm. All was fine until I rebooted.
I get pages of lvm errors and booting fails. It looks like it's trying to mount the volumes before the sata controller is modprobed. Is there a way to get the os to modprobe for the new controller before trying to mount? The extra drive space is on a data partition, not the boot partition.
View 7 Replies
View Related
Mar 12, 2011
I want to install Ubuntu 10.10 via a DVD-ROM but I faild. I got the message "no common cd-rom drive was detected." I have tried to install ubuntu 11.4 and failed too.
Hardware Setting:
DVD-ROM was attached to SATA 3.0 port.
SATA controller was set to IDE mode.
PCH is CougarPoint.
I use the same hardware setting to install Red Hat 6.0 and it works fine. I tried following boot option but in vain: noapic, acpi=off, nodmraid, all_generic_ide. It is ok to boot via a live usb but ubuntu 10.10 still can't find DVD-ROM. I have to use the hardware setting I descripted to install Ubuntu 10.10.
dmesg:
Code:
[ 1.892198] ata1: SATA max UDMA/133 cmd 0x3098 ctl 0x30ac bmdma 0x3070 irq 19
[ 3.309652] ata1.01: failed to resume link (SControl 0)
[ 3.469636] ata1.00: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[code]...
View 5 Replies
View Related
May 12, 2010
i just burnt a debian lenny 504 live disk. i don't think there's a way to install it to hard drive. i just did a google search and it appears that the latest debian lenny 504 cannot be installed to hard drive with the live cd. from what i have read, i need to get a "netinstall" iso (this is new territory for me). can anyone supply me with a link for an iso with a hash verification? i would be most grateful. the disk i had previously must be corrupted because the install quits at 5%.
View 2 Replies
View Related
Apr 16, 2010
I'm trying to install 10.04b2 x64 on my new rig and for some reason the live cd can't detect both of my 1TB Sata 3 drives. There is no Raid and the bios has them flagged as IDE. I have also tried adding pci=nomsi to the boot string to no avail.
View 8 Replies
View Related
Mar 16, 2010
I have been Linux user(Ubuntu)for about 3 years since my switching from Windows. Although I did not have any complain against it, I wanted to try Debian Lenny. I have already partitioned my disk and installed Debian. Everything worked fine according to my expectations except for one thing: wireless.I tried different things to get it works without result. The light indicator of my computer seems to be working but the Network Manager does not detect any signal. In Ubuntu the wireless is detected automatically even using the Live CD.
View 1 Replies
View Related
May 28, 2011
ubuntu 8.04 server can not detect seagate sata hard drive 2tb or sata Lg dvdrw x22 sata drive .is it possible to install it without buying a pci ide sata card?is it possible to get a driver for sata driver and sata drive that can be recognise by ubunto 8.04 server ?or to get the files for 1.44 floppy diskdoes the late edition of unbutu recognise sate hdd and sata cdrw drive automaticly during the installation of the unbutu?
View 1 Replies
View Related
Mar 18, 2011
Ethernet is not detected with the following setup:
OS: Debian Lenny
Laptop: Dell Latitude D600
Ethernet adapter: Broadcom 57xx Gigabit Integrated Controller
Wifi adapter: Broadcom BCM4309 802.11a/b/g
Have done the following troubleshooting suggestions from around the www:
LAN controller is enabled in BIOS
dmesg | grep eth0 returns nothing
lspci -v | grep -i net shows wifi adapter but no ethernet adapter
ifconfig -a does not show eth0
ifconfig eth0 up confirms ERROR while getting interface flags: No such device
Have done lsmod, but not sure what I should be looking for.
I would post lspci, dmesg or any other output, but as the adapter is not being detected, I have no network/internet connection from that laptop, have only one other Windows based (at this stage) laptop that I am using to write this message, and so would have to type out the output manually.Adapter indicators are both on when laptop is powered up. Am unsure if the ethernet adapter has somehow gone to sleep, and if so, unsure how to wake it.Perhaps the ethernet adapter is defective, but am hoping to confirm this before looking for a workaround/replacement.
View 14 Replies
View Related
Dec 14, 2009
i was trying to use gnome and kde but i don't like them. I tried xfce and it seem to fit my needs but.My computer is used to be powered on for a weeks. While time passes, a process xfdesktop begin to use more and more memory and to free RAM i need to log out and log in again.
I tried squeeze yesterday on my virtual machine and it has 4.6 and seem not to have that bug, RAM usage is static(yes it still works when i write this and have memory usage 34492k, which is not changing for an hours of usage already), also 4.6 is MUCH better than 4.4.
i already tried adding squeeze to "sources.list" but i can see too many dependencies which should be upgraded if i install 4.6, i'm beginning to afraid it can crash entire GUI(or entire system, i can see there is libc6 required to be updated).
View 14 Replies
View Related
Feb 4, 2011
We have an external raid box connected to a debian squeeze server.Every new volume set I have created will be detected (as /dev/sdx) after a reboot. As this is our file-server I cannot reboot the server every-time a new volume set is created.Is there a way to make this new device visible.I tried already 'partprobe' and restarting udev didn't work eather.What is a good way to do this?
View 3 Replies
View Related
Apr 13, 2011
I have just installed opensuse 11.4 and the install fails to boot, grub hangs or gives an error.
I have tried installing grub in MBR and root changed every setting I can find and even downloaded a fresh ISO. As a last resort I changed the machines BOIS settings from SATA to emulate ide, booted as expected but a bit slow.
11.2 and 11.3 worked on this machine with no problems. Am i missing something? I also tried an Ubuntu install and this worked fine!
View 9 Replies
View Related
Apr 25, 2010
Is it possible to install Linux on an external SATA drive?I have a system dual booting between OpenSuse and Windows XP. I wanted to see what other distros were like so I tried installing Ubuntu to my external SATA drive. After installing, I got an error from GRUB, and I had to recover my MBR.I tried the same thing with Mandriva, and got the same result. Finally, I tried another install of OpenSuse 11.2. The result was that I get a grub error 21. The only result of my efforts to try other distros is a lot of experience recovering my MBR.
View 9 Replies
View Related
Jan 21, 2011
This is on Debian Lenny 5.0.7 with a LXDE desktop. Using Root Terminal I have just been trying to mount a SATA drive NTFS file system using the command: mount -t ntfs /dev/sdb1 /dev/
unfortunately the /sdb1 should of been 'sdc1', I think, and what's happened is that my username and files have been moved somewhere else. PCMan File manager has ceased to work and open applications have ceased to be able to save files.
How do I discover where they went, and how do I restore them back to the original place of debian:/home/username/ ?
I'm about 8 hours in to learning Linux/Debian and desperately trying leave behind about 15 years of Windows use for something better. I'm used to troubleshooting electronics/hardware/all manner of things but the syntax here is, at the moment, a slippery slope.
View 2 Replies
View Related
Mar 10, 2011
I have a Dell XPS 420 with a 500gb SATA drive on which Windows Vista is installed. I also have an additional hard drive that I wish to install for an Ubuntu installation. Is it possible to create a dual boot system with Windows on the original HD and Ubuntu on the newly installed HD?
Simply put, my computer will have 2 hard drives. The original hard drive has Windows installed. I would like for the second drive to contain the Ubuntu install so that the only thing changed on the original drive is the MBR (I suppose that's how it would work).
View 4 Replies
View Related
May 3, 2010
I am trying to install Debian from a USB stick (which was prepared by unetbootin). The installer / kernel loads, and setup runs fine until It searches for a CD-ROM drive. My computer doesn't have a CD-ROM drive, but the net install ISO has been burned onto my USB stick. Is there some way that I can mount my USB stick as the cd-rom drive? it's of type FAT32 if it matters.
View 2 Replies
View Related
Feb 19, 2010
Recently we started getting these errors in syslog:
Code:
[31944.813993] hda: status timeout: status=0xd0 { Busy }
[31944.813993] ide: failed opcode was: unknown
[31944.813993] hda: drive not ready for command
[31949.822516] hda: status timeout: status=0xd0 { Busy }
[Code]....
Also the machine was under very high load and almost impossible to connect to.
I've searched, and found mostly answers involving broken hard disks or other hardware issues, but this is unlikely to be the case here: it started happening on several machines at the same time. They are HP DL580G5, and hda is the DVD player. It's not being used. The only thing we've recently changed is that we installed HAL (as a dependency of pcscd), and sure enough, killing HAL freed up the cpu and stopped the stream of errors. Sadly, pcscd requires HAL..
Has anyone seen this? Are there known problems with HAL in Lenny on HP hardware? I know I could do hal-disable-polling /dev/hda but I don't want to simply ignore a potential problem.
EDIT: versions used are HAL 0.5.11-8, pcscd 1.4.102-1 and kernel 2.6.26.2-amd64
View 1 Replies
View Related
Jan 15, 2010
So I installed SUSE 11.1 a few weeks back with two SATA drives andit's been working great. I recently received another SATA drive and wanted to add the space to my /home directory. I installed the drive and then booted up my computer. It goes through BIOS and POST just fine but when I get to GRUB my computer just hangs there. It doesn't throw any errors, it just sits until I hard reboot it. If I disconnect the extra SATA drive and then try to boot again everything starts successfully. I've done a little bit of searchingbut couldn't find much on this problem.pretty new to linux so I could definitely be missing something. Let me know if more details are needed.
View 9 Replies
View Related
Jan 17, 2010
Basically, I have no trouble booting off a really old kernel like 2.6.18-6. If I try to boot off the newest one installed with Lenny, I get errors such as "mounting /dev/ on /root/dev failed...ditto for /sys on /root/sys" almost as if it's failing to find the drive. This finishes up with "target filesystem doesn't have /sbin/init" and I'm dropped into a busybox shell.It's an ordinary SATA drive, which is being used as an OS drive only. It seems as if something has changed with the newer kernel, but I have no idea where to start or what to look for.
View 3 Replies
View Related
Jun 13, 2010
I have an old computer that I want to turn in to a backup server. I was planning on using a 1 TB drive connected by a SATA card since the motherboard only has PATA. However when looking everything I've found makes it sound like I need to install the card for it to work. I want to know if I can install Debian to the hard drive through the SATA card or not?
View 6 Replies
View Related
May 20, 2010
I recognize the obvious need to back up the contents and follow a certain duty of care before attempting to clone my failing pata 250g HD to a 1 tera byte sata. What problems if any could come up when cloning from a failing pata to a sata HD? I'd like to make the switch to sata for many reasons if possible. It is indicated that the HP d530 sff here supports both types.
View 2 Replies
View Related
Mar 18, 2011
I am attempting to get Debian Lenny 5.0.8 to run on an OpenSolaris snv_134 lx-branded zone. Debian 6.0.0 is a total flop due to the included udev requiring a kernel >= 2.6.26 and the kernel provided by the lx26 brand being only 2.6.18.So I installed Debian 5.0.8 into a VirtualBox VM, configured it, then tarred up the install with the following command as root, from /:
tar -cjf /mnt/share/debian-5.0.8.tar.bz2 --exclude dev --exclude sys --exclude mnt --exclude proc *
I then installed that archive into a solaris zone, booted it, and had to run
perl -pi -e "s,1 1,1 0," /etc/fstab
in order to fix up the fstab. Now it boots (with a handful of warnings), but the problem I'm having is that I can't run apt. I get:
E: Couldn't determine free space in /var/cache/apt/archives/ - statvfs (75 Value too large for defined data type)
View 2 Replies
View Related
Jun 29, 2010
I've bought a new e-sata external HDD. It work fine if it's connected throught USB. The problem goes when I connect it throught e-sata. The disk isn't detected (see the first screenshot).I must restart my computer to get the HDD detected (the HDD must be pluged in while booting, I think).Is it possible to repair that? I need the HDD to be detected immidiately when connected, like USB, without any restart.
View 1 Replies
View Related
May 15, 2011
I tried to install 11.04, but the partition tool shows no HDD. If I try to run Ubuntu from the CD, I can explore the HDD but the partition tool in the installation program won't find it. What can be wrong with my Promise SATA controller
View 8 Replies
View Related
Jun 21, 2010
I have a i3 processor and MSI p55-cd53 motherboard. My problem is fedora cannot detect the 2nd SATA, so that I can configure raid1.
View 1 Replies
View Related
May 15, 2009
I have an issue with Hard Drives in GNU/Linux CentOS 5.3I installed linux 5.3 frash copy to new SATA MAXTOR 1000GB Hdd.And see the partitions is SATA MAXTOR 1000GB (NEW INSTALLATION CentOS 5.3)
/dev/sda1 Boot
/dev/sda3 /
(/dev/sda2 is the SWAP)
[code].....
View 5 Replies
View Related
Feb 19, 2010
I am a frequent user of debian I think I'll be a lot here start immediately with a problem, and I hope that someone has already happened and found a solution. In practice I have to install a IBM x3250 m3 and the cd installer debian lenny 5.0.3 or 5.0.4 do not want it to find the CD-ROM drive, a module to mount the drive after the bootstrap the exact error on the screen comes up after selecting the language and keyboard: no common cd-rom drive was detected cd-rom modules
View 1 Replies
View Related
Feb 8, 2011
All of my computers are second-hand (except 1 laptop but it doesn't count) and I see in my Dell 4600 there are 2 SATA connectors on the motherboard. I picked up a 250 GB SATA hard disk and cables recently and tried plugging it in but the system doesn't see it. I even disconnected all other disks to make sure there wasn't a conflict (master/slave) issue going on but the system still does not see it.
The disk is vibrating so I assume it is getting juice and is spinning. Is there a setting or something I have to do to tell the system to access the SATA? Do I have to look at RAID settings if there is only 1 SATA disk? Can I not have a SATA disk and an ATA disk plugged in at the same time? I want to try and determine if the disk is bad, or is it PEBKAC!
View 11 Replies
View Related
Oct 19, 2010
used to run ARC linux and Windows 7 on my computer and i am now trying to install Ubuntu 10.10 X86_64When i used the live disc of Ubuntu 10.04 and load the installer it finds my four harddrive they way it should... sda,sdb,sdc,and sdd...When i however try the same with ubuntu 10.10 it displays my usb cardreaders drives first and then my hardrives as sde sdf sdg and sdh.I tried installing ubuntu with the reader unplugged and then reconnecting it after installation...But when i then boot with the reader attached it says it cannot mount drives sda,sdb,sdc and sdd becuase they are not ready.I think it is again detecting the usb cardreader before the sata controller ...Is there a way for me to alter the boot detection order so it will find my harddrives first and then the usb cardreaders ports ?
View 1 Replies
View Related
Jan 24, 2010
I am trying to install FC4 in my pc having WDC WD800JD SATA HDD. During the installation it shows that no HDD found. I have searched a lot but no driver are found for fedora core 4.
View 10 Replies
View Related
Jun 1, 2010
My motherboard supports SATA but I do not know which version: SATA-I or SATA-II. I want to buy a SSD so it would be pointless to buy a fast SSD if my motherboard only suports SATA-I
View 7 Replies
View Related
