Recently I installed Fedora 12 without any hassles except that the USB devices are not getting detected. I checked with /proc/interrupts and the ehci_hcd module doesn't get any interrupts. Here is my dmesg (done to show only USB related messages) :
Code:
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
[code]....
I am just getting started with Ubuntu and love it so far. It has breathed new life into an old Compaq Presario V2000 and once I get up to speed on it I hope to start running it on all the rest of our machines.
The only major problem I am having is that none of the USB devices I have plugged in are being detected. From what I have seen online I should be getting a notification and should be able to view the devices at Places/Computer but so far, nothing. Googling this problem it appears that individual devices often don't work but I could not find anything on all USB devices not working.
Any ideas as to what I am doing wrong here?
Last week, I received a used, older (built ~ 2005 or so) IBM ThinkCentre desktop (machine 8143-2EU) having a Pentium 4 (64 bit), 3.0 GHz CPU. It came with WinXP- 64 bit as the sole OS. When I tested my USB devices with the WinXP OS, they were detected and read. I wiped the WinXP and installed MEPIS 11- 64 bit. [There's only a single Intel Pentium 4, 64 bit CPU known to work for MEPIS 11- 64 bit. It's the Pentium 4 Prescott with EM64T. I don't know if my P4 is that one.] Things seem OK with my MEPIS 11- 64 bit OS except for the times when I plug in USB devices--> they're not detected nor read. In a MEPIS forum, a guy told me to try, after first plugging in the USB devices, running lsusb in Konsole. I do that, the system wakes up, and the USB devices are detected and read. But why do I have to do this to get my system to detect and read the devices? I've made the MEPIS system setting so that all USB devices are automounted when plugged in. Doing that did not correct this problem. As root, in Konsole, I ran hwinfo and noticed that for the USB controllers, the driver - uhci_hcd - is not active. Here's the hwinfo output for one of the USB controllers:
18: PCI 1d.2: 0c03 USB Controller (UHCI)
[Created at pci.318]
UDI: /org/freedesktop/Hal/devices/pci_8086_265a
[code]...
[I suppose or guess that all MEPIS users who don't have this USB-device-detection-and-read problem have uhci_hcd.] To see what would happen as a test, I also used a MEPIS 11- 32 bit Live DVD in this computer having the MEPIS 11- 64 bit OS. When I use the Live DVD, I have the same USB detection-and-read problem! What does that mean? With some USB devices plugged in while I'm using the Live DVD, I'm forced again to run lsusb in Konsole. This wakes up the system so that it detects and reads plugged-in USP devices. Why? Any idea on how to fix this? Does this problem seem more a software one rather than a hardware one?
After I installed my ati grapics driver (the ati driver from the ati website) my ubuntu has this weird problem. When loading there is a line that cought my attention:
Running DKMS auto installation service for kernel 2.6.34: fglrx (8.543)...Failed
I think that has something todo with the other error I get which is:
Primary device is not PCI
(EE No devices detected)
Fatal server error
no screens found
giving up.
I have an ATI 5650 Radeon mobile grapics card By the way.
My USB devices are being detected when I run the 'lsusb' command.However there is no driver that is set to the device.Also the /dev/sdX device is created so there is a mount point
View 1 Replies View RelatedI recently had a hard drive on a computer (not to be obvious), and I fried the computer. You may ask "well why did you do that?" well, simply because I had accidentally bumped and switched to 220 volts, rather than keeping it at 115 like a sane individual. Anyway, I got a new computer, swapped the hard drive. When I go to boot into ubuntu though, it gives me the following error:
Code:
Ubuntu is running in low-graphics mode
The following error was encountered. You may need to update your configuration to solve this.
(EE) No devices detected.
I also have XP on this hard drive, and it works almost better than it did on my old one, surprisingly. all i have to do now for it to be labeled as efficient, is to get some RAM. But anyway, what can I do about the error message? I tried booting into recovery, running dpkg from the list of options, and it did a couple of things.
Whenever I plug in my usb flash drive or my memory card adapter they are not detected. If you can help me I will provide any kind of information needed to solve the problem, just tell me what command to run. Also my cd/dvd drive is still not being detected or is mislabeled on ubuntu 10.04 lucid lynx.
View 3 Replies View RelatedI have an issue with Hard Drives in GNU/Linux CentOS 5.3I installed linux 5.3 frash copy to new SATA MAXTOR 1000GB Hdd.And see the partitions is SATA MAXTOR 1000GB (NEW INSTALLATION CentOS 5.3)
/dev/sda1 Boot
/dev/sda3 /
(/dev/sda2 is the SWAP)
[code].....
I am having problems understanding how sound capable devices are being used on my Ubuntu10.10 64 bit system. I have an ASUS A8V motherboard with on-board multimedia functions provided through the VIA V8237 chip. BIOS gives me the option to disable this functionality and I have set BIOS this way. I want to use an M-Audio 24/96 card for all sound processing.
However, in applications like Audacity the VIA chip functions are all available and can be set as recording and playback devices. The same is true in ALSA.
Why does 'linux' (I have no idea which part of the OS) ignore the BIOS settings?
Furthermore alsamixer always selects the 'default' devices. Where and how are these set?
<System><Preferences><Sound> hardware tab list 2 'Internal Audio' devices but no M-Audio device. What are these devices? Only 1 of them appears to create any output with the 'Test Speakers' tab. This confuses me completely because the speakers are connected only to the M-Audio card.
None of the profiles for 'Settings for the selected device' match the capabilities of the M-Audio card (1 set of stereo inputs and 1 set of stereo outputs). So where are these profiles coming from? Which do I select for the M-Audio card?
What do the Input and Output tabs in <System><Preferences><Sound> mean? Are these different to the hardware tab? The 'Output' tab lists2 devices for sound output: 'Internal Audio Analog Stereo, Stereo' twice. What devices are these ?
I have installed Imgburn and it wont detect my cd drive, I configured wine and everything and no matter what I can't get it to recognize my driver, what am I to do?
View 9 Replies View RelatedI'm having issues getting the nvidia-current drivers working with a GeForce 8400 graphics card on Ubuntu 10.10 (x64). After running nvidia-xconfig and restarting, X fails to start with an error: No devices detected.
Here is my xorg.conf:
Code:
# nvidia-xconfig: X configuration file generated by nvidia-xconfig
# nvidia-xconfig: version 260.19.06 (buildmeister@builder101) Mon Sep 13 04:59:45 PDT 2010
Section "ServerLayout"
[code]....
Rhythmbox plays some music (not all of it) and it sounds crappy. And when I start Amarok I get this: KDE detected that one or more internal sound devices were removed. Do you want KDE to permanently forget about these devices? This is the list of devices KDE thinks can be removed: Output: HDA Intel (INTEL HDMI) Output: HDA Intel, INTEL HDMI (HDMI Audio Output)What to do?
View 4 Replies View RelatedI dl the windows installer one and ran it. As it started it went to the Ubuntu logo and then my screen became half full of different colored horizontal lines, so I rebooted and went into the adv boot and ran the install under safe graphics mode. Now when I boot I get options to boot into 2.6.32-25 and also a recovery and also 2.6.32.24 and a recovery. I left the 2.6.32-25 highlighted and it booted but gave me a msg that said:
(EE) VESA: Kernal modesetting driver in use, refusing to load.
(EE) No devices detected.
Then it goes to a screen that allows me to boot in a low graphics mode. It loads and I dl some security updates with the Update Manager. What do I need to do in order to boot w/o any faults and also what is the difference from 2.6.32-25 and 2.6.32-24? Which should I be using? Do I need to modify my graphis somehow?
I tried to install the latest RealTek driver for Linux and it has wiped all my devices. I've tried reinstalling the alsa-base packages but it hasn't worked
View 4 Replies View RelatedI've been struggling a bit with install F11. F10 installs without issue. I have two internal SATA drives, a PATA DVD-ROM and a USB drive. The BIOS recognizes everything. However, when I got to the disk partition utility, Anaconda could never detect one of the SATA devices. I tried swapping cables, ports, etc. No luck. Today, I ran across this Bug thread: [URL] I checked the screens Ctrl-Alt-F1-6. Nothing obvious. But, for fun (from the bug thread) I went to the prompt on 2 and ran:
dmraid -r -E It found an "nvidia" RAID "thingy". Forgive my ignorance on what it really is called or what it does. Anyway, I answered yes to erase the "thingy" and voila. I was able to install F11. Not sure if I made a good title, but I've seen bits and pieces of people having similar problems with F11. And BTW, the drive that had "nvidia" on it was from a machine that was using nvidia hardware RAID 0 - but F10 had no problems with it.
I've been running F10 with a four disk RAID5 setup that has been working fine, however when I tried to do a fresh install of F11 I can't get past the "Select Country" and "Select Keyboard" screen of the GUI as a message will say "Detecting Storage Devices" and then throw up an error. I can't give you the full error, because when I click Save The Detecting Storage Devices box appears and I can not select anything under it or enter my Bugzilla account.However, when I plug just the hard drive that has XP on it then the installer continues swimmingly.I've backed up everything, so if I have to I could zero out the drives however they're all rather large so it'd take an inordinate amount of time.
View 2 Replies View RelatedBefore I changed to linux, I was on Windows 7. My computer already had 4 different partitions, and would not let me create more. And so, I had to delete one of the partitions. I chose to get rid of the "recovery" partition. I used "Macrium Reflect" to burn a bootable CD of my recovery stuff. Anyways, fast forward to this morning. I got tired of the KDE desktop, and I decided to switch to Gnome. So, I went into windows 7, deleted the three OpenSUSE partitions, and moved the remaining space back to my C: (windows) drive. (don't ask me why :S)
Anyways, so I take a look, after it's done deleting/moving stuff, and I'm told that "no bootable devices detected".. This made me angry, as I am certain I didn't delete any of the windows partitions. So, I thought, I'll just use my recovery disk, because I quite literally, have no personal data on my computer to lose.Except, my recovery disk is not actually bootable. So, then, after screaming in rage, I booted up OpenSUSE from my KDE CD, and was gonna take a look at things in YaST. Except, YaST will not actually open.
I installed Imgburn yesterday and it worked fine.Today i open it and it says "No devices detected" which doesn't let me copy anything.
View 4 Replies View RelatedWhile installing Fedora 12, no devices were found on which to create file system (see attch.). I get the same message either on Live CD or DVD boot start. It looks like Fedora do not see my hdd. But Palimpsest can see my hard drive (see attch.)
Hdd is on my NForce 4 Ultra m/board and connected via "sata". Also I have raid controller on my board. But it is not in use: I turned it off in bios.
I'm installing F12 on a new HP ML-350 G6. The machine has 4 Gb memory, and a Smart Array P410i SAS controller. There are two 72 Gb disks set up as a RAID 1. I'm using a full install DVD. There are no other storage devices other than the RAID, a USB tape drive, and the DVD drive. When I try to install F12 it hangs after setting the keyboard type with "Finding Storage Devices". I've let it sit for an hour or more and it doesn't get beyond that.
F11 installs on the machine with no problem. I've used the F12 DVD on other machines with no problem (but not any other ML-350s). If I switch to a console session, dmesg shows the driver for the controller (HP CISS) has loaded and the RAID drive recognized. The appropriate devices (/dev/cciss/c0d0, /dev/ccss/c0d0p0, etc.) are all present in /dev.
As stated running f13_64 and trying to run preupgrade to 14 fails in anaconda after reboot.
Just hangs at "examining devices". I've looked online and theres several bug issued for this nothing really ever seems to be fixed.
Is this just broke? The preupgrade?
I cant go to f15 as it will not run on my machine at all. Never quite loads gnome proper.
Pretty standard p35 board /core duo. One drive with a /boot /LVM setup straight from the f13 installer.
I installed Fedora 12 and performed the normal updates. Now I can't reboot and get the following console error message.
ERROR: via: wrong # of devices in RAID set "via_cbcff jdief" [1/2] on /dev/sda
ERROR: removing inconsistent RAID set "via_cbcff jdief"
ERROR: no RAID set found
No root device found
Boot has failed, sleeping forever.
Getting very frustrated trying to install F12 to my work PC. Its a dell precision 670 with a 3ware 9550sxu raid controller running raid 5. Its consistently crashing at the point when it says 'finding storage devices' with a message about : Mismatched Sizes. What I could try? I had no problem on this machine with fedora 11, so whats changed? Just for info by the way, theres two raid volumes on this system a 750Gb that contains my windows vista installation in a 500 Gb partition (NTFS) and the free space I'm using for fedora. The second volume is a 2TB data volume with a single data partition (NTFS).
View 1 Replies View RelatedWhy is it that FC6 installs just fine from a USB CDROM in an external enclosure but FC12 boots from the CD asks to install or upgrade an existing system but then stops at no devices found and wants the install path for the install image? It appears to see the CDROM, boots then looses its mind and forgets a CDROM was attached.
View 13 Replies View RelatedFirefox's Plugin Finder Service says that it is an unknown plugin when visiting pages. I have tried the manual install using rpm and yum along with trying to uninstall and reinstall via Add/Remove Software.When looking at Extensions within Add ons, Flash is not shown on the list.
View 2 Replies View RelatedWe are try to install Fedora 12 or Fedora 13 x86_64 on HP Server Blade ProLiant BL460c G6. And when the installer try to find storage devices - it can not find any hard drivers. We are have message on screen - "Finding storage devices" and the installation process is not continue.... Fedora 10 and Fedora 11 x86_64 are installed very well. The device /dev/cciss/c0d0 is present in system and all it partitions - c0d0p1, c0d0p2 ... Command fdisk -l /dev/cciss/c0d0 has no any output.
lsusb -v output:
0c:00.0 RAID bus controller: Hewlett-Packard Company Smart Array G6 controllers
(rev 01)
Subsystem: Hewlett-Packard Company Smart Array P410i
[code]....
I have just installed Fedora 14 on my desktop machine and have just discovered that it can't detect my WiFi card. The card is an Edimax EW-7711In which the makers say will run with Linux. I know that the card works fine with Ubuntu because my brother uses the same card in his Ubuntu machine but he is away until after Christmas so I don't know what he did to make it work other than I know he used ndiswrapper and the Windows drivers that were supplied with the card. I have looked for ndiswrapper in the Fedora repositories but it doesn't appear to be there.
View 14 Replies View RelatedI am trying to install FC4 in my pc having WDC WD800JD SATA HDD. During the installation it shows that no HDD found. I have searched a lot but no driver are found for fedora core 4.
View 10 Replies View RelatedI'm stuck after a clean install of FC14 on an old Everex StepNote (Doing this for a friend). I tried Ubuntu on it first (because it's so easy) but had horrible stability issues and terminal commands wouldn't respond - however Ubuntu detected and ran the eth0 port just fine. FC14 detects my ethernet NIC, but it won't work.
Here are my details.
lspci outputs this for my NIC:
00:12:0 Ethernet controller: VIA Technologies, Inc. VT6102 [Rhine-II] (rev 7c)
Here is what I have tried so far - with no luck:
- I have toggled the networking switch on the laptop and had no luck.
- Downloaded Via's VT6102 drivers for Fedora Core, but they don't support kernel 2.6.35.*
- Run ifconfig to manually assign an IP address - which it DID take and did route add default gw as well.
- Did a ifconfig eth0 down and up as well.
After all that, I still have a "disconnected" wired connection (and yes, I did check the cable - it works just fine in my personal machine.
I 've a Nokia CS-10 broadband stick (USB). I need to install and configure, and I don't know how do it. I found an article that review something like that: [URL]
1, The stick doesn't detected in the computer.
2. I made all the article steps, but shows me a error in the shell script on line 10.