Fedora :: Raid1 Setup - Second SATA Not Detected
Jun 21, 2010I have a i3 processor and MSI p55-cd53 motherboard. My problem is fedora cannot detect the 2nd SATA, so that I can configure raid1.
View 1 Replies
ADVERTISEMENT
Fedora :: Adding SATA Drive - Not Detected By The Bios ?
Oct 18, 2009I have a working F-10 box with an older motherboard (pre-sata). The p-ata ports are full (4 drives), so I'm trying to add a sata controller and another drive. The sata controller plugs into the pci bus, but is not detected by the bios (very old). After booting, the OS loads the driver module(s) and detects the new controller and drive. I was able to add the new sata drive into the LVM system using system-config-lvm. All was fine until I rebooted.
I get pages of lvm errors and booting fails. It looks like it's trying to mount the volumes before the sata controller is modprobed. Is there a way to get the os to modprobe for the new controller before trying to mount? The extra drive space is on a data partition, not the boot partition.
Fedora Hardware :: New SATA Hard Disk Not Being Detected
Feb 8, 2011All of my computers are second-hand (except 1 laptop but it doesn't count) and I see in my Dell 4600 there are 2 SATA connectors on the motherboard. I picked up a 250 GB SATA hard disk and cables recently and tried plugging it in but the system doesn't see it. I even disconnected all other disks to make sure there wasn't a conflict (master/slave) issue going on but the system still does not see it.
The disk is vibrating so I assume it is getting juice and is spinning. Is there a setting or something I have to do to tell the system to access the SATA? Do I have to look at RAID settings if there is only 1 SATA disk? Can I not have a SATA disk and an ATA disk plugged in at the same time? I want to try and determine if the disk is bad, or is it PEBKAC!
General :: SATA HDD Not Detected During Fedora Core 4 Installation?
Jan 24, 2010I am trying to install FC4 in my pc having WDC WD800JD SATA HDD. During the installation it shows that no HDD found. I have searched a lot but no driver are found for fedora core 4.
View 10 Replies View RelatedDebian :: Adding 2 New SATA Drives As RAID1?
Feb 8, 2009i have 2 shiny new 1TB SATA drives. I have a running system already, basic install on a single disk. install both new drives & raid1 them on a single partition - mount them for storage. Seems simple but all i can find are howto's on instaling the whole system & booting on RAID.
View 1 Replies View RelatedCentOS 5 :: Mistakenly Setup RAID 0 Array On / Instead Of RAID1 During Setup - Convert Without Loss?
Dec 15, 2010So I didn't notice when I setup my CentOS 5.5 server that I left / as RAID 0 on md1. All the rest are RAID 1. Is there a way I can modify the array to RAID 1 without a risk of data loss? I'm glad I caught this before I setup any other services. I've only setup smb so far...
[root@ftpserver ~]# df -h
Filesystem Size Used Avail Use% Mounted on
/dev/md1 16G 3.0G 13G 20% /
[code]....
Fedora Hardware :: Sata III Controller Marvell 88SE9182 Can't Be Detected (on Rampage III Extreme Black)
Aug 24, 2011I bought a Rampage III Extreme Black Edition wich has a SATA III controller (Marvell 88SE9182). I try to install Fedeora Core 15, but FC15 just dont recognize any of my HDs placed in SATA III ports. Has any fellow succeed installing linux on this SATA Controller?
View 8 Replies View RelatedUbuntu :: Not Detected E-sata Without Restart?
Jun 29, 2010I've bought a new e-sata external HDD. It work fine if it's connected throught USB. The problem goes when I connect it throught e-sata. The disk isn't detected (see the first screenshot).I must restart my computer to get the HDD detected (the HDD must be pluged in while booting, I think).Is it possible to repair that? I need the HDD to be detected immidiately when connected, like USB, without any restart.
View 1 Replies View RelatedUbuntu Installation :: 11.04: SATA HDD Not Detected?
May 15, 2011I tried to install 11.04, but the partition tool shows no HDD. If I try to run Ubuntu from the CD, I can explore the HDD but the partition tool in the installation program won't find it. What can be wrong with my Promise SATA controller
View 8 Replies View RelatedCentOS 5 Hardware :: /dev/sda (SATA) Devices Detected As /dev/hda?
May 15, 2009I have an issue with Hard Drives in GNU/Linux CentOS 5.3I installed linux 5.3 frash copy to new SATA MAXTOR 1000GB Hdd.And see the partitions is SATA MAXTOR 1000GB (NEW INSTALLATION CentOS 5.3)
/dev/sda1 Boot
/dev/sda3 /
(/dev/sda2 is the SWAP)
[code].....
Ubuntu Installation :: How To Setup Software RAID1
Sep 27, 2010I recently set up an old desktop computer on my home network for use as a file server. I installed Ubuntu 10.04 Server on it and I'm slowly learning how to make it do what I want (I'm used to the GUI, so this is a bit of a jump for me).My plans are to put two 1.5TB hard drives in the computer (there's already a 160GB with the OS installed) and put them in a RAID1 configuration. This, as I understand it, will write all data to both drives, creating two identical drives. I'll only have 1.5TB total space for backup, but if one of the hard drives die, I can replace it without losing any data.
Hopefully I understand all that correctly. Now, my questions are how to actually set a RAID configuration up. I don't have a controller or anything, assuming I could do it off the two SATA ports in the motherboard (the 160GB is IDE) in software RAID.Once I have the two hard drives set up in RAID1, how do I allow the house to access the file storage?We're all on Windows 7 computers.If one of the hard drives fail, how will I know? Can I set it up so I receive some sort of notification? Also, how does the replacement process work; can I just pop the broken drive out and put a similar one in? Do I need to readjust any settings after replacing one?
Debian :: SATA DVD Drive Not Detected During Lenny Install?
Nov 17, 2010I am trying to install Debian 5.0 "Lenny" on a PC with a very new hardware config (i3 processor, DDR3 RAM,LG SATA DVD drive, and Seagate SATA HDD). During the hardware detection phase of installation, I get a message saying the driver for my CD drive is not known, and asking me to select one manually. The options I get are only 'devcdrom', which does not work, and my installation cannot proceed.
I tried the following:
1. I read in a similar query that to use SATA DVD drives, I will have to set some boot options, so tried entering install libatapi_enabled=1 as an install option. This showed 'unknown parameter' error followed by same problem.
2. My Intel m/b BIOS has an option to set the DVD drive to "Native" or "Legacy", default is Native. I also tried changing this to "Legacy". Still same problem.
3. Read that I have to point to different drivers, but don't know how to do this during the installation.
Ubuntu Installation :: Sata 3 Drives Not Detected During Install?
Apr 16, 2010I'm trying to install 10.04b2 x64 on my new rig and for some reason the live cd can't detect both of my 1TB Sata 3 drives. There is no Raid and the bios has them flagged as IDE. I have also tried adding pci=nomsi to the boot string to no avail.
View 8 Replies View RelatedUbuntu Installation :: USB Detected Beofre The Sata Disks Are?
Oct 19, 2010used to run ARC linux and Windows 7 on my computer and i am now trying to install Ubuntu 10.10 X86_64When i used the live disc of Ubuntu 10.04 and load the installer it finds my four harddrive they way it should... sda,sdb,sdc,and sdd...When i however try the same with ubuntu 10.10 it displays my usb cardreaders drives first and then my hardrives as sde sdf sdg and sdh.I tried installing ubuntu with the reader unplugged and then reconnecting it after installation...But when i then boot with the reader attached it says it cannot mount drives sda,sdb,sdc and sdd becuase they are not ready.I think it is again detecting the usb cardreader before the sata controller ...Is there a way for me to alter the boot detection order so it will find my harddrives first and then the usb cardreaders ports ?
View 1 Replies View RelatedSlackware :: Setup Software RAID1 On A Running System?
May 23, 2011I have a nas / server running Slackware64-13.37 with two raid arrays, one with 3x500GB disks and the other with 2x2TB disks. I also have 1x80GB hdd which contains the os. I found a spare 250GB hdd from my closet and want to set up raid1 array from os hdd and that spare drive.I know that I can't make use of the extra 170GB of space but I don't care as long as I have working installation on the other disk if that 80GB hdd breaks. How can I set up that kind of raid1 without losing any data?
View 1 Replies View RelatedUbuntu Installation :: SATA 3.0 & IDE Mode : No Common Cd-rom Drive Was Detected
Mar 12, 2011I want to install Ubuntu 10.10 via a DVD-ROM but I faild. I got the message "no common cd-rom drive was detected." I have tried to install ubuntu 11.4 and failed too.
Hardware Setting:
DVD-ROM was attached to SATA 3.0 port.
SATA controller was set to IDE mode.
PCH is CougarPoint.
I use the same hardware setting to install Red Hat 6.0 and it works fine. I tried following boot option but in vain: noapic, acpi=off, nodmraid, all_generic_ide. It is ok to boot via a live usb but ubuntu 10.10 still can't find DVD-ROM. I have to use the hardware setting I descripted to install Ubuntu 10.10.
dmesg:
Code:
[ 1.892198] ata1: SATA max UDMA/133 cmd 0x3098 ctl 0x30ac bmdma 0x3070 irq 19
[ 3.309652] ata1.01: failed to resume link (SControl 0)
[ 3.469636] ata1.00: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[code]...
General :: Sata Hard Disk Not Detected While Installation Of Ubuntu?
Mar 29, 2010i'm using athlon 64 bit , asus a8vmx mbd, 1gb ram
View 3 Replies View RelatedCentOS 5 Hardware :: How To Enable Detected Hot Plugged SATA Drives
Feb 23, 2009I'm in rescue mode with Centos 5.2 disk trying to install/mount a new disk to extract data out from the failed server.
Plugged in a new SATA drive and syslog shows the drive being detected
SCSI device sdg: blah
sdg: Mode Sense: 00 3a 00 00
sdg: unknown partition table
sd 3:0:0:0: attached scsi disk sdg
However fdisk and mount does not find the drive. I tried echo "---" /sys/class/scsi_host/host3/scan based on one of the previous threads but get "write error: invalid argument".
how should I get the drive to be usable?
Ubuntu :: Hard Drives (RAID1 Via Firewire) Setup Sought?
Aug 14, 2010I searched, and unfortunately all that did was raise my confusion level on this. "Grub"? "mdadm"? "fake"?, S/Wraid? Disk utility? So many options, so little understanding! Relevant stuff (Mostly reported by "Disk utility"):
- Lucid Lynx. PATA host adaptor -> IDE controller -> Maxtor 164GB H/D [I *think* this has Windoze on it, but can't remember!] There's also a CD & DVD drive on this IDE bus. PATA host adaptor -> SATA controller -> Seagate 500GB H.D. - The Ubuntu boot drive, currently a 250GB ext4 partition, 3GB swap and 250GB "unused".Peripiheral devices -> Firewire 400 -> 2 x Samsung 500GB H/D's. These were "stolen" from my Mac Book and are currently a RAID1 Apple array. Everything they contained is safely backed up, and these can be considered as "new" drives awaiting formatting. [It's actually a Buffalo Drivestation Duo, but their site was even more confusing than here.
everything is working wonderfully, but I'd like to use the 2 F/W drives in a RAID1 array - So, eventually to the question: How do I tell Ubuntu to use these drives as a RAID array? It seems I can format and partition etc from disk utility. Do I then use mdadm for configuration? Any other recommendations?
Ubuntu Installation :: Lucid - 250GB Sata Hard Disk Not Detected By Partitioner
May 1, 2010The hard disk is seen in the BIOS.
The partitions on it are accessible via the Places Menu on the Lucid Live CD.
It's just when I try to install, nothing is detected in Step 4 of 8, "Prepare Partitions".
An old 80GB IDE disk, on the other hand is seen by the partitioner.
I am not using RAID and it is not enabled in the BIOS.
Hardware :: Can SATA 3 (SATA III) Hard Disk Be Run On Motherboard Which Only Support SATA II
Aug 13, 2010Can SATA 3 (SATA III) Hard disk be run on motherboard which only supports SATA II, except sacrificing the speed (throughput)?
View 2 Replies View RelatedUbuntu :: SATA II / Error "ata4: Limiting SATA Link Speed To 1.5 Gbps" - Allowing The SSD To Run At SATA II Speeds?
May 1, 2011I keep getting this error in my log viewer every 2 seconds: Code: ata4: limiting SATA link speed to 1.5 Gbps I have a dual boot SSD and I have run many SMART tests in windows and linux, (using smartmon tools and the disk utility) and the reports are all 100% healthy..... My research shows that this error represents one of the following:
1. Problem with SATA controller
2. Changing BIOS to allow SATA
3. Changing SATA mode to PATA or AHCI
4. Replacing the SATA cable
5. Allowing the SSD to run at SATA II speeds, i.e. 3 Gbps
- Does anyone know how to try number 5, i.e. allowing the SSD to run at SATA II speeds? I am lost here and this problem has caused my machine to crash twice when watching a movie in linux/ ubuntu. (It is worth noting that the crashes have only occurred in linux and I have never had an issue in windows, so it does seem to be a linux setting somewhere, hence why I think it is a "allowing SATA II to run at correct speeds issue")
CentOS 5 Hardware :: Kernel NOT Detected "Ibex Peak 2 Port SATA IDE Controlle" Chip?
Nov 29, 2010In our company, we have one server with kernel, 2.6.18. because of our neads, we had to buy new hard disk,that slax live cd detects that as "Ibex Peak 2 port SATA IDE Controlle".Apparently this kernel does not support this device.Unfortunately according to our policy(definitely some dependency on company's softwares installed on this kernel) we can not upgrade our kernel.
View 1 Replies View RelatedUbuntu Installation :: Unable To Dual Boot In 3 SATA Drives Setup
Jun 4, 2010I have the following PC set up:
Dell 8400 with 3 GB of RAM with 3 160 GB SATA drives:
The first one has Windows XP installed on it.
The second one has been newly formatted and Ubuntu 10.04 has just been installed on it (20 GB / and 6 GB swap) with grub being installed on the first partition and not the master boot record. The remainder will be for storage for Windows.
The third drive is simply storage for Windows.
At this point I am able to boot XP just fine, but I'm not able to boot Linux. I just getting a blinking cursor or the PC just reboots when I choose Linux. I believe I have set up my boot.ini properly using:
C:Bootsectc.lnx="Linux Ubuntu"
After running dd if=/dev/sdc1 of=bootsect.lnx bs=512 count=1 and putting that file in place.
For reference, I don't believe this is a Linux problem, as much as I am simply trying to guide the ntldr to be properly pointed to a place where it can boot Linux. When I go into the bios and disable the first and the third hard drives, grub pops right up and I'm able to boot Linux with no problem, so that piece is fine. I think it's just now trying to get the correct syntax so I can boot Linux without having to disable drives and reenable them.
For kicks I even tried these syntax types in boot.ini:
multi(0)disk(0)rdisk(1)partition(1)="Linux11"
(i.e. 2nd disk, 1st partition ...etc...)
I read many troubleshooting documents on dual booting and so forth but I just can't get this right. For reference, I stated the way XP views my Hard Drives in the intro, which seem to be a different order than Linux sees them, yet I believe I've tried all the combos of settings for this to work (yet clearly have not). I have attached the output of boot_info_script*.sh here: [URL]. Boot Info Script 0.55 dated February 15th, 2010 ..... Devices which don't seem to have a corresponding hard drive.
Debian :: Setup Error - Libc6 Not Detected
Mar 9, 2016I'm having another issue when trying to install a particular software package.
I'm trying to install a CityEngine 2015.2 trial and when I run the setup script using ./Setup, I get the following error:
Code: Select all[CityEngine 2015.2 Setup Error]
libc6 not detected
I tried reinstalling libc6 to no avail and searching the net for answers but couldn't find any solutions.
I parsed the script for that exception and found the following code:
Code: Select allelif [ "x` which dpkg-query 2>/dev/null `x" != "xx" ]
then
DetectedLibcVersion=` dpkg-query -s libc6 2>/dev/null | grep ^Provides: | cut -f2 -d'-' `
if [ "x${DetectedLibcVersion}" = "x" ]
then
error_header
echo "libc6 not detected" >&2
exit 1
fi
Ubuntu :: SATA Libata Verses Silicom Images SATA Module
Jun 21, 2010I installed Ubuntu 10.04, and happened to have an Silicom Images PCXpress card plugged in, and it kindly added the sil_sata module.This is fine for this chip set.I think that my earlier installation of Ubuntu 9.04 used Libata, which does support NCQ and also has good legacy support for the Intel Intel ICH7 chipset I have inside my Sony Vaio SZ notebook. Also, libata also support Silicon Image chipsets as far as I can tell from URL...I wish to remove the Silicom Images SATA modules and replace this with libata and then test the performance between the two device drivers.
View 5 Replies View RelatedFedora :: F13 - Boot With RAID1 / LVM / Dracut?
Dec 10, 2010I am trying to boot my F13 server that has 3 partitions (sda2,sdb2,sdc2) configured as RAID1 (md0), vg00 is on md0 and / is on vg00/lvol00 and boot is on /dev/sda1, sda3,sdb3 and sdc3 contain other non-OS data and I get the following errors
dracut scanning devices sda3,sdb3,sdc3 for LVM logical volumes vg00/lvol00 vg00/lvol01
.
dracut: Volume group "vg00" not found
dracut: Skipping volume group vg00
dracut: Autoassembling MD Raid
No root device round
and then everything stops
If I go in with rdshell and type in -
[Code]...
Ok I managed to solve it. When I originally installed F13 I had 2 partitions in md0 and later on I added /dev/sdc2 to make it a 3 partition Raid 1 array. My thinking was seeing that I had the extra space it wouldn't hurt to use it as another mirror. One month later after I booted the server I have found out it did hurt. I removed the 3rd partition and now it's fine again. I wonder though if it would be possible though to use that 3rd partition.
Fedora :: Can't Mount RAID1 Array?
Dec 29, 2010I have just upgraded to Fedora 14 from an older version. I now have problems mounting my RAID1 array, which was operating correctly until now. This is a software RAID which was initially built under Fedora 10.The array is md0, and is made of 2 SATA drives (sdc and sdd) which have only one partition. The underlying filesystem is NTFS. The array is assembled correctly and active, as reported by /proc/mdstat and mdadm -D.When I try to mount the array, I get this:
Code:
[root@Goofy ~]# mount /dev/md0 /mnt/raid
mount: you must specify the filesystem type
[code].....
Debian :: Check If Mainboard Supports SATA-I Or SATA-II?
Jun 1, 2010My motherboard supports SATA but I do not know which version: SATA-I or SATA-II. I want to buy a SSD so it would be pointless to buy a fast SSD if my motherboard only suports SATA-I
View 7 Replies View RelatedFedora :: Resync Two Raid1 Hard Disk In 12?
Jun 9, 2010I have two 80 GB IDE hard disk. I have create raid1 partition in both drive using [URL] ink. raid is working fine. But i have copy some data on one hard disk (md0) but this data is not autometically copy in second hard disk(md1). I want when data is write on one hard disk, this data autometically write in second hard disk.
View 11 Replies View Related