General :: Sata Hard Disk Not Detected While Installation Of Ubuntu?
Mar 29, 2010i'm using athlon 64 bit , asus a8vmx mbd, 1gb ram
View 3 Replies
ADVERTISEMENT
Ubuntu Installation :: Lucid - 250GB Sata Hard Disk Not Detected By Partitioner
May 1, 2010The hard disk is seen in the BIOS.
The partitions on it are accessible via the Places Menu on the Lucid Live CD.
It's just when I try to install, nothing is detected in Step 4 of 8, "Prepare Partitions".
An old 80GB IDE disk, on the other hand is seen by the partitioner.
I am not using RAID and it is not enabled in the BIOS.
Fedora Hardware :: New SATA Hard Disk Not Being Detected
Feb 8, 2011All of my computers are second-hand (except 1 laptop but it doesn't count) and I see in my Dell 4600 there are 2 SATA connectors on the motherboard. I picked up a 250 GB SATA hard disk and cables recently and tried plugging it in but the system doesn't see it. I even disconnected all other disks to make sure there wasn't a conflict (master/slave) issue going on but the system still does not see it.
The disk is vibrating so I assume it is getting juice and is spinning. Is there a setting or something I have to do to tell the system to access the SATA? Do I have to look at RAID settings if there is only 1 SATA disk? Can I not have a SATA disk and an ATA disk plugged in at the same time? I want to try and determine if the disk is bad, or is it PEBKAC!
Hardware :: Can SATA 3 (SATA III) Hard Disk Be Run On Motherboard Which Only Support SATA II
Aug 13, 2010Can SATA 3 (SATA III) Hard disk be run on motherboard which only supports SATA II, except sacrificing the speed (throughput)?
View 2 Replies View RelatedUbuntu Installation :: ASUS A8V-MX Recognises SATA Hard Disk?
Aug 11, 2010This is a solution to a problem that has bugged me for months but I finally got around to solving.I hope this will be useful to anyone using Ubuntu with GRUB2 who has the same problem.I am running Ubuntu 10.4 Lynx which did not recognise the newly-installed SATA HDD.In fact, booting up would face me with a recovery shell.The solution is to add the pci=nomsi kernel parameterTo do this you need to edit the /etc/default/grub file and add the kernel parameter as follows:
Code:
GRUB_CMDLINE_LINUX_DEFAULT="quiet splash"
GRUB_CMDLINE_LINUX="pci=nomsi"
[code]....
General :: Install Redhat9 On Sata Hard Disk?
Nov 14, 2010How can i install redhat9 on sata hard disk.
it always ask for drivers & i didn't find it.
Ubuntu Installation :: Hard Disk Partitions Not Detected In 10.10 LiveCD
Nov 21, 2010I tried to install ubuntu 10.10 today through livecd. but the partitions in my 60gb samsung harddisk are not detected. My entire harddisk is shown as unallocated free space. Also gparted is not detecting the partitions as well. I am currently not facing any problems with my partitions in windows xp. I tried the solution given here (to no avail): [URL]. I have had no such problems with previous versions of ubuntu.
View 9 Replies View RelatedGeneral :: Can Install Old Versions Of Redhat For SATA Type Hard Disk
Dec 14, 2010Can i install old versions of redhat linux (like versions 3,4,5) for SATA type hard disk. I heard that SATA disk will allownew versions of redhat linux only.
View 4 Replies View RelatedGeneral :: SATA HDD Not Detected During Fedora Core 4 Installation?
Jan 24, 2010I am trying to install FC4 in my pc having WDC WD800JD SATA HDD. During the installation it shows that no HDD found. I have searched a lot but no driver are found for fedora core 4.
View 10 Replies View RelatedUbuntu :: Second SATA Hard Disk Doesnt Show Up?
Aug 31, 2010I've installed 500 GB SATA hard disk but SUSE doesnt see it. The BIOS recognized the disk. What do I do in order to get the disk show up as sdb.
View 1 Replies View RelatedOpenSUSE Hardware :: Second SATA Hard Disk Doesnt Show Up?
Aug 31, 2010I've installed 500 GB SATA hard disk but SUSE doesnt see it. The BIOS recognized the disk. What do I do in order to get the disk show up as sdb.
View 9 Replies View RelatedCentOS 5 Hardware :: 3 Sata Hard Disk System Can Not Startup?
Feb 18, 2010server is :intel 5000p ,2gX4 ram ,cpu 5405 X13 sata sda 500g sata use for system rootfilesystem primate mastersdb 500g sata use for data filesystem second mastersdc 500g sata use for data filesystem second slavebios set use enhance and ide i install centos5.4 x86_64 on sda when i install system on sda, sdb and sdc is offline.after system install sucess ,poweroff and add sdb and sdc when system kernel start report ata0 error or ata1 error. exp XXXX (rydy).but when only add sdb or sdc ,system can startup and use all service ,exp vncserver ,kvm,pptp..
View 2 Replies View RelatedUbuntu :: 9.04 - 2nd Hard Disk Not Detected At Start Up?
Jun 3, 2011I Installed Ubuntu 9.04 with XP theme. Then I installed Picasa and I have pictures on a 2nd hard disk. When I restart the PC Picasa doesn't see the 2nd drive. The 2nd HDD is mounted under /media/disk and clicking on the "My computer" icon (this is XP theme), I see the 2nd hdd. Now, I have to add this disk to Picasa again for it to scan the pictures. I don't want to do this on a regular basis.
View 1 Replies View RelatedUbuntu Installation :: 11.04: SATA HDD Not Detected?
May 15, 2011I tried to install 11.04, but the partition tool shows no HDD. If I try to run Ubuntu from the CD, I can explore the HDD but the partition tool in the installation program won't find it. What can be wrong with my Promise SATA controller
View 8 Replies View RelatedUbuntu Installation :: Ubunto 8.04 Cannot Detect Sata Hard Drive Or Sata Drive Cdrw?
May 28, 2011ubuntu 8.04 server can not detect seagate sata hard drive 2tb or sata Lg dvdrw x22 sata drive .is it possible to install it without buying a pci ide sata card?is it possible to get a driver for sata driver and sata drive that can be recognise by ubunto 8.04 server ?or to get the files for 1.44 floppy diskdoes the late edition of unbutu recognise sate hdd and sata cdrw drive automaticly during the installation of the unbutu?
View 1 Replies View RelatedDebian :: Hard Disk Not Getting Detected
Mar 18, 2011I am trying a network install of debian 6.0 by dumping the contents of a DVD onto my local http server. For some reason the Western Digital 80 GB pata HDD doesn't get detected when I click on 'detect disk', I even tried with a SATA, no luck.
View 7 Replies View RelatedUbuntu Installation :: Sata 3 Drives Not Detected During Install?
Apr 16, 2010I'm trying to install 10.04b2 x64 on my new rig and for some reason the live cd can't detect both of my 1TB Sata 3 drives. There is no Raid and the bios has them flagged as IDE. I have also tried adding pci=nomsi to the boot string to no avail.
View 8 Replies View RelatedUbuntu Installation :: USB Detected Beofre The Sata Disks Are?
Oct 19, 2010used to run ARC linux and Windows 7 on my computer and i am now trying to install Ubuntu 10.10 X86_64When i used the live disc of Ubuntu 10.04 and load the installer it finds my four harddrive they way it should... sda,sdb,sdc,and sdd...When i however try the same with ubuntu 10.10 it displays my usb cardreaders drives first and then my hardrives as sde sdf sdg and sdh.I tried installing ubuntu with the reader unplugged and then reconnecting it after installation...But when i then boot with the reader attached it says it cannot mount drives sda,sdb,sdc and sdd becuase they are not ready.I think it is again detecting the usb cardreader before the sata controller ...Is there a way for me to alter the boot detection order so it will find my harddrives first and then the usb cardreaders ports ?
View 1 Replies View RelatedUbuntu Installation :: Copy Hard Disk Have 10.04 And Ext4 To 1000 Hard Disk?
Sep 23, 2010I want to copy hard disk have ubuntu 10.04 and ext4 to 1000 hard disk for new 1000
View 2 Replies View RelatedUbuntu Installation :: SATA 3.0 & IDE Mode : No Common Cd-rom Drive Was Detected
Mar 12, 2011I want to install Ubuntu 10.10 via a DVD-ROM but I faild. I got the message "no common cd-rom drive was detected." I have tried to install ubuntu 11.4 and failed too.
Hardware Setting:
DVD-ROM was attached to SATA 3.0 port.
SATA controller was set to IDE mode.
PCH is CougarPoint.
I use the same hardware setting to install Red Hat 6.0 and it works fine. I tried following boot option but in vain: noapic, acpi=off, nodmraid, all_generic_ide. It is ok to boot via a live usb but ubuntu 10.10 still can't find DVD-ROM. I have to use the hardware setting I descripted to install Ubuntu 10.10.
dmesg:
Code:
[ 1.892198] ata1: SATA max UDMA/133 cmd 0x3098 ctl 0x30ac bmdma 0x3070 irq 19
[ 3.309652] ata1.01: failed to resume link (SControl 0)
[ 3.469636] ata1.00: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[code]...
OpenSUSE Hardware :: External Hard Disk Not Detected By USB 3.0 Port?
Aug 15, 2011Hardware: Toshiba Satellite L755Software: openSuse 11.4 with kernel 3.1.0-rc1-98-g72fa599-1-vanillaPeripherals: Logilink USB 3.0 to SATA HDD Adapter with Western Digital WD2500JSI installed the Vanilla kernel in the hope that USB 3.0 will work. But though some things really have been fixed (for instance, the notebook can resume from sleep mode), USB 3.0 still doesn't work.
Code:
lsusb
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
[code]...
General :: No Hard Found, When Installing RHEL5 On SATA 3 Hard?
Mar 20, 2011I tried installing Red Hat linux on my Sata hard disk . As soon as the hardware detection phase starts it generates the error "No hardware detected".roblem? (I have also tested RHLE 5, CentOS 5.4, but none of them detect the hard disk and I can not install anyone).I have installed Windows 7 on one of my disks and I have not any problem with it.I also changed storage configuration in Bios as AHCI, IDE,
My Hardware config is as below:
Mainboard: ASUS P6X58D premium,
CPU: core i7 950,
HDD: two 1 TB WD SATA3
Ram: 6 GB (3*2 GB cruciall[/U][/U][/B]
General :: Changing GRUB From An External Hard Disk To The Internal Hard Disk?
May 14, 2010I had a dual boot (windows 7 + debian), both of them installed in my internal hard disk, with the GRUB in it. I have recently installed a second linux distro (mint), but I put it in an external hard disk. Now the GRUB allows me to boot any of the three operating systems, but I need the external disk to do it. It seems that after the mint installation the GRUB is now working from the external disk (if the external disk is not connected, the machine does not boot.) �Is there a way to change the location of the GRUB, to the internal hard disk of my laptop?
View 2 Replies View RelatedDebian Installation :: No Boot Disk Has Been Detected Or Disk Has Failed
Nov 3, 2015I installed Debian on my PC with a Acer Stock motherboard (xc600) with amd64 and after the installation finished it told me to remove my installation media and reboot. After reboot I was returned this message ' ERROR: No boot disk has been detected or the disk has failed.'. I have verified with gparted using mint live OS that I have Debian installed on my system.
I got believes that this may have be caused by a broken grub or I need to configure something I don't know how in BIOS.
I will update the topic later..
My installation media was a USB 2.0 flashdrive with a Debian 8.2 Jessie Installer and 9 different Linux distros. I have installed Debian multiple times before on my laptop and never had this problem so I know how to go through the installation process and set the partitions.
Ubuntu Installation :: Karmic Cannot See Sata Disk Known Bug?
Mar 11, 2010Is this a known bug? I've not had problem installing 9.04 but 9.10 will not see HDD under partition manager(ubiquity) no matter the F6 boot options or fiddling around with bios. If ubuntu can't see the hdd, I can't install. 785G chipset with SB710 FYI.
View 4 Replies View RelatedUbuntu Installation :: Can't Partition Sata Disk
Nov 26, 2010I'm trying to install 10.10 on a sata disk. In terminal, dmesg recognizes the disk at /dev/sda. The installer recognizes it as well, but the partition area is blank and the option are greyed out. How can I go on? BTW, on the disk currently Fedora 14 is (fresh) installed and working fine, but a software install script is written specifically for Ubuntu. That's why I need to change to Ubuntu and it's no hardware problem.
View 9 Replies View RelatedFedora Installation :: Hard Disc Not Detecting For Seagate SATA Hard Disc?
Jul 15, 2009I have AMD athlon 64 processor, Seagate 160GB SATA Hard Disk, ASUS A8VMX mother board.With this configuration, I can Install FC7 without any error. But all the latest releases after FC7 is not detecting my Hard disk. Is there any solution to solve this problem? Actually I'm searching for a solution when the FC8 released. Now I have all the later releases from FC8 to FC11 DVD except FC9. But none is working .
View 1 Replies View RelatedGeneral :: Use Hard Disk Image Like A Regular Hard Disk?
Apr 6, 2010If you have a hard disk image (including partition table, multiple partitions,...), is it possible to let Linux treat it as a regular hard disk?
By "regular hard disk" I mean I would like to have the image show up as, for instance, /dev/hdx and its partitions as /dev/hdx1,...
(I know I can mount one of the partitions in the image using "mount -o loop,offset=x ..." but I don't really like this option.)
Ubuntu Installation :: 9.10 Can't Find SATA Hard Drive On DG45ID?
Apr 5, 2010I have a Desktop system using the Intel DG45ID motherboard with integrated graphics. I can't install from the 9.10 LiveCD. It can't find the Hard drive which is on the chipset's SATA controller.However, I can install 9.04 just fine. I can even do the 9.10 upgrade without a problem.Does anyone know if this bug has been reported. I'm hoping 10.4 has this fixed. I'll test the beta to see
View 9 Replies View RelatedUbuntu Installation :: Two Hard Drives Vista On SATA Empty IDE
Jul 21, 2010I have two drives one is a 500 gig SATA drive running Vista SP 2 now the other Maxtor 160 Gig drive is empty. I would like to install Ubuntu on that drive. Now I just though of installing from the setup however would this screw up my Vista partition ?
View 1 Replies View Related