Ubuntu :: Installed The Nvidia 185 Drivers And It's Not Recognizing Monitor As A Flat Panel Lcd?
Mar 10, 2010
i have a viewsonic VA712b monitor that used to get 1280x1024 resolution on my dell optiplex gx260 that had the intel video card.i upgraded my motherboard cpu and memory..the nvidia 6100 that is onboard seems like it would be an improvement to my old onboard intel but the best resolution i can get is 1024x768
i installed the nvidia 185 drivers and it's not recognizing my monitor as a flat panel lcd but as a crt, also it won't set the correct refreshrate - either 60 or 75.. it's set at 50... since xorg 7.4 no longer uses a xorg.conf file.. i'm not sure how to go about manually adjusting the settings to ones that will actually work. i mean other than buying a separate graphics car (URL)
I have been using ubuntu for quite a long time, and for the first time, I am now unable to set nvidia drivers to work. I have just install ubuntu 9.10 amd64 on an AMD 64 athlong X2 with a GEForce 6500 nvidia card.
The only reason I need the proprietary drivers is to use two monitors.
I am going crazy, I have tested everything I have found on the web. I have tried all the nvidia drivers version, I have tried envyng, ... but nvidia do not work!!
I am trying Xinerama with nv, but it does not work either!!!
Here is my xorg.conf file in which I have tried to use nv driver to set dual monitor. X fails to load and it says that screen 0 is deleted, that devices are found but there are no matches in the config file. Any clue?
opensuse 11.2 ,my monitor keeps going to sleep or somthing and this is a problem when im watching videos,ive set screens power setting but they dont seem to be whats doing it.im running a nvidia gtx260 and have installed nvidia drivers for series 6 and up.dont know if its the divers or somthing else.
I have Ubuntu 10.04 installed. Everything works fine until I enable the Nvidia drivers. When I enable the drivers and reboot the top and bottom panel stop displaying. If I issue command 'pkill gnome-panel' it all comes up and works correctly.
I am at a loss here as I am somewhat new to Ubuntu. Where to start looking for the problem? I've thought about setting up a startup script to run 'pkill gnome-panel' after I login, but that doesn't really fix the core of the problem.
When i was on the live cd installing ubuntu it said i could install my driver but now that i am running off the hard drive it doesn't pick it up under "Hardware Drivers"
I'm installing 10.4 fresh but I can't get the Nvidia drivers installed. I'm using a 9400 GT. Ubuntu installs normally but when I try to enable to the proprietary driver, I get an error on reboot "Failed to initialize NVIDIA graphics device" and have to restart X. Any suggestions on how to get this working?
I've just installed the brand new Ubuntu 11.04 and all goes well until...I log in a session. There is a window telling me that my graphic card isn't too good to run Unity, when I have no problem under 10.10 to run all the eye-candy. Now I have a NVIDIA Quadro NVS 120M with 512 megs of memory. I've install the NVIDIA current driver in the Additional Drivers application and reboot. But nothing...in the additional driver app it says that the current driver is installed but not currently in use...what should I do before giving up and install unity-2d?
I am trying to install nVidia drivers on CentOS 5.4 and it is requiring kernel-source # lspci | grep VGA 01:00.0 VGA compatible controller: nVidia Corporation G98 [GeForce 8400 GS] (rev a1)
For the installation of kernel source, I have followed the steps on [URL]. I followed the steps under 2.1 and they worked for me. Now what can be done for the installation of the kernel-source package. When I am trying to install nVidia drivers, I am getting error, following are lines from installation log of Driver.
-> Tagging shared libraries with chcon -t textrel_shlib_t. -> License accepted. -> Installing NVIDIA driver version 185.18.31. -> No precompiled kernel interface was found to match your kernel; would you like the installer to attempt to download a kernel interface for your kernel from the NVIDIA ftp site [URL]? (Answer: Yes) -> No matching precompiled kernel interface was found on the NVIDIA ftp site; this means that the installer will need to compile a kernel interface for your kernel. -> Performing CC sanity check with CC="cc". -> Performing CC version check with CC="cc".
ERROR: Unable to find the kernel source tree for the currently running kernel. Please make sure you have installed the kernel source files for your kernel and that they are properly configured; on Red Hat Linux systems, for example, be sure you have the 'kernel-source' or 'kernel-devel' RPM installed. If you know the correct kernel source files are installed, you may specify the kernel source path with the '--kernel-source-path' command line option.
ERROR: Installation has failed. Please see the file '/var/log/nvidia-installer.log' for details. You may find suggestions on fixing installation problems in the README available on the Linux driver download page at [URL]. I want to install driver.
The nVidia Driver I am installing is: NVIDIA-Linux-x86-185.18.31-pkg1.run # uname -a Linux harvey 2.6.18-194.3.1.el5PAE #1 SMP Thu May 13 13:48:44 EDT 2010 i686 i686 i386 GNU/Linux Only reason to install the proper driver is to use dual monitor.
I seem to have an issue with my nvidia drivers again.I get them working, then the next lot of updates to fedora seems to revert any progress I've made.Currently I can't run any 3d accelerated applications, no wine, no games etc, I have followed the documentation, installed the driver, added the blackist to noveau into boot.conf, and restarted
I want to run both World of Warcraft and Steam under wine, but WoW won't work with the latest 195.x.x driver, and steam won't work with the previous 185.x.x driver.
Is it possible to have both installed, and to switch between them as needed for different applications? Or will I really have to choose between one or the other?
I had to install the nVidia proprietary drives so the OS would boot into Gnome3 and not fail safe mode. Without the proprietary drivers installed the display settings said:
Driver: software rasterizer in use
After installing the nVidia drivers Gnome3 works in one monitor, but I would like to be able to use my other two monitors (totaling three with two video cards.)
When I run nvidia-settings to generate an xorg.conf file it hangs, so I used nvidia-xorgconf to generate the xorg file and then used nvidia-settings to configure my extra screens.
This fails with a permissions error, running sudo nvidia-settings fails with the following error:
ERROR:
So, I ran nvidia-settings, saved the settings file to my /home/$USER dir, then copied xorg.conf to /etc/X11/
Logging out and logging back into Gnome fails with the error:
This problem extends to Ubuntu running Gnome3, so my thinking is: a) Imma id10t and something in my xorg.conf file is wrong, b) there is an issue with Gnome3/nVidia/Multiple displays.
I would really like to use Gnome3, it works on multiple other machines (ironically all ATI devices) just not the machine I use all day long...
Here is my xorg.conf file as generated by nvidia-settings.
This is my first post, as I've finally become fed up with trying to get the nvidia drivers installed on Fedora 10. I've read through all the posts here about how people have had problems. I know about the rpmfusion repository, and have followed leigh123's instructions to the letter at this link:[URL]The exact stepsI have taken before following his sage advice follows this way: install off the CD image I burned of Fedora 10, run from the menus "System-->Administration-->Update System" to get the system up to date, reboot to make sure everything is working fine.
Then I follow the above instructions (only because they have gotten me the closest to getting the drivers working). After the reboot from following those instructions, the system starts up, and I have a desktop. But when I restart again, either because I'm shutting down for the night, or just to check again that everything is fine,I get nothing but a flashing cursor in the upper left of my screen. I'm able to CTRL+ALT+F2 and get to a login that way, but can't get into the GUI. I've searched the forums (both here and on The Web generally), and can't find a fix for this that works for me. I have gone back and erased the partition and reinstalled, so I'm at the basic install with all the updates for my system, and needing help with getting the drivers installed and working.
Just to give a run down of what I have on my system:Two NVidia 8500 GT cards connected with the SLI bridgeAMD Athlon 64 X2 Dual Core 3800+Runningl 2.6.27.12-170.2.5.fc10.x86_64 (I'm typing this up as I reinstall updates as I listed above).Before anyone starts giving suggestions, please make sure to give the full instructions, as I'm new to Fedora/Linux. And if there is anything else you wish to know about my configuration
Today I finally could install Fedora 15 i686 in my now aging (2005) desktop computer (although I will always think of it as my "new machine", as long as I don't assemble a new one for me):
After I installed F15 my initialpression was that it worked really good on that hardware: everything went fine with GNOME 3 for example,except for some lags in graphics rendering, which I thought would be solved after the graphics card's full power were unleashed with the proprietary NVIDIA driver.For starters I am not sure which Nvidia driver is right for my card (Nvidia 173.X or the regularvidia).I managed to get "working" the 173.X driver but the desktop is even less responsive to begin with, and there appears to be a lot of activity on the hard disk side.So, my question is, which could be causing the performance loss?
A. The "small" RAM. B. The vintage graphics card. C. Some problem in the hard drive. D. A known bug.
i have just installed opensuse 11.3 on my PC and updated all packages and all and then i installed nvidia drivers from this link SDB:NVIDIA drivers - openSUSE i downloaded the 1 click install file nvidia.ymp and installed the driver successfullybut then when i rebooted the PC for the driver to work,it doesn't work,and when i go to system>look and feel>desktop effects and i try to enable the effects i get the message that i cant enable the effects it gives me this message "Desktop effects are not supported on your hardware / configuration. Would you like to activate them anyway?" PS i say "no" to this message and it closes but i notice there is a constant use of 33% of the CPU and theres an unnamed/unknown process in the system monitor that keeps appearing and disappearing...thats quitrd because i installed opensuse 11.2 and 11.3 before and i never had these problems
I installed the nvidia proprietary drivers with click-install and everything perfect, I have desktop effects working but the problem is that when you open the config. screen settings to make sure everything was really good, I get to screen unknown April.
The maximum resolution is the correct 1440 * 900 for 19 "but the refresh rate by not recognizing the monitor down to 50hz me and gives me the option to 60hz as it was before installing the nvidia drivers.
Sometimes, in Firefox, after looking a video and closing the corresponding tab, a still picture of the video appears in other tabs, even in some other applications than Firefox (e.g. Terminal). I've installed the nvidia drivers on Fedora 14. They seem to work properly.
After installing ubuntu 64 bit, I installed all my updates and installed the current nvidia driver for my 9800 GTX+ from the additional drivers page. After restarting my computer, ubuntu boots into text mode. I used google and found out a couple of commands like:
After i hit control+alt+f7 it hangs on checking battery state with NO ok to the right of it. after running sudo apt-get --purge remove nvidia -current and restarting the computer, the boot hangs on the ubuntu screen everytime.
My specs are: Core i7 860 4 GB of ram Nvidia 9800 GTX+
I have activated dual screen monitors using the Nvidia driver GUI as Sax2 would not correctly configure it. Now at every boot I get the message "undefined video mode 31a, press [enter] for a list of video modes or [space] to continue. After pressing space the system boots to my liking, how can I get rid of the message at every boot up?
I am using Suse 11.2 and KDE4.3.1 My video card is an Nvidia Geforce 7100 GS I thought I was using the Nvidia drivers as I have a GUI from Nvidia in my launch menu if I search "Nvidia" and I have completed the one-click installation. Although when I go into "My Computer" it says driver unknown.
I am new to Linux and actually just finished my install about 30 minutes ago. Ubuntu 10.04 isn't recognizing my wireless adapter, so I need to install the drivers. I know where the drivers are, I just don't know how to install them on a Linux system.
Here is the driver page. I don't know how to download the .inf file (necessary?) but I have ndiswrapper, bcmwl5.sys, and sp33008.exe all in the downloads folder.
Apparently just double clicking the files does nothing, so what do I do now?
i just recently installed an nVidia GeForce 6200 (AGP 256mb) and it worked great out-of-the-box for the computer. i've been trying to hook up a tv as a second monitor and don't seem to be having much luck. i followed a few HowTo's and some threads but nothing seemed to help - here's the configuration i'm using an s-video cable out to an A/V RF Mod box and an RF co-ax from the RF Mod to the TV (I tested the RF Mod and it works).
The output of dpkg --get-selections | grep java on Karmic Koala is ca-certificates-javainstall java-commoninstall libaccess-bridge-javainstall libaccess-bridge-java-jniinstall sun-java6-bininstall sun-java6-jreinstall tzdata-javainstall
Yet when I go to a site like keepvid.com and enter a valid URL I get: Error: Please click here to download Java. If you already have Java, please restart your browser and try again. It appears you do not have Java installed or it is disabled on your system. You can get Java here. If you are still having difficulty with Java, check here for installing Java, or here for detailed instructions on enabling Java in your browser.
Running openSUSE 11.3, Linux 2.6.34.7-0.5-desktop...
I'm trying to install the <a href="http://www.ctan.org/tex-archive/macros/xetex/latex/arabxetex/">arabxetex</a> package. It requires XeTeX, so I installed that via YaST package manager. I got hold of a TDS archive of the package and installation as prescribed <a href="http://www.tex.ac.uk/cgi-bin/texfaq2html?label=inst-tds-zip">here</a> went smoothly. But when I try
Code: latex myfile.tex, It says "* XeTeX is required to complile this document. Sorry!" and the resulting dvi file is completely blank.
LaTeX (latex -v) is "pdfTeX using libpoppler 3.1415926-1.40.10-2.2 (TeX Live 2009/openSUSE)".
xetex -v gives "XeTeX using libpoppler 3.1415926-2.2-0.9995.2 (TeX Live 2009/openSUSE)".
Can anyone think of why the package might not be recognizing that XeTeX is installed
I installed Xubuntu the other night (completely wiped machine) and started doing all the updates on it. After a couple of reboots, I changed from the proprietary drivers, to the regular nVidia drivers. After doing this, the startup logo is displayed at a really low resolution. Is there a simple fix to change this and use the nVidia drivers as well?
I can't figure out how to install the nvidia drivers for my nvidia 8800 GT video card. I've followed some other posts and all the posts seemed either incomplete, or led me down a path of which eventually broke my installation, that I needed to reinstall the entire ubuntu system.Again, it may not have been broken, i just didnt know how to get back in to the gui version of ubuntu, the instructions took me to the console terminal
1.) I've installed the ubuntu 10.10 64bit for i386 in an oracle virtualBox..
2.) downloaded from nvidia.com "NVIDIA-Linux-x86_64-260.19.44.run"
Currently I have two 1920x1080 screens running in Twinview on my Geforce 275 graphics card. Want I want to do is a quick simple way of disabling my secondary monitor when playing video games or using xbmc to watch movies, etc. I've tried a few applets but they require the xandr function which I think Nvidia doesn't support.
Is there a way to disable this quickly other than loading up nvidia-settings and disabling the monitor everytime. I don't really want to use two seperate x sessions and xinerama due to the fact you can't use compositing.
[URL] I just updated and then saw this news , whats the solution for me, I either want to go beta or downgrade, If i try to boot to previous kernel, boot hangs in graphic mode, I cant start X and gdm . How to install kmod with beta drivers? Or whats the solution, nvidia ver: 195.36.08
just setup suse 11.3 , put on the Nvidia 19.29-22.1 drivers via yast , no kms is set in inetd , nomodeset on grub boot line etc... Even tried installing the driver " the hard way " dual monitors come up, setup xinerama to "Extend" my desktop , and the main monitor ( right side ) is good, visually the left monitor (2ndary) is good.. but whenever I move my mouse over to the left screen the mouse pointer dissapears, flickers along the right hand border of that screen... and if i move the cursor back to the original screen i have to really fight to get it back to the main screen....Copy of my xorg.conf , still very basic...
# nvidia-settings: X configuration file generated by nvidia-settings # nvidia-settings: version 260.19.29 (buildmeister@swio-display-x86-rhel47-04. nvidia.com) Wed Dec 8 12:27:27 PST 2010
I have Ubuntu 10.10. I want to install the from the nvidia website. The propriatary drivers from Ubuntu aren't great. I have downloaded the file, but what do I do with it now? How can I get it installed?
After rdblacklist=nouveau in grub it runs, but I am having several issues and therefore I would like to downgrade to nouveau or whatever I had running with basic fedora 12 installation.
I Have just formatted to Fedora 14 64bit and installed kmod-nvidia akmod-nvidia and am experiencing visual lag. The lag did not occur before I installed the drivers, neither did it occur on Fedora 13 with drivers installed.
I have a priitty high spec pc with the nvidia 260 gtx.
just remove xorg-x11-drv-nvidia-libs-260.19.12-3.fc14.i686
