Sometimes, in Firefox, after looking a video and closing the corresponding tab, a still picture of the video appears in other tabs, even in some other applications than Firefox (e.g. Terminal). I've installed the nvidia drivers on Fedora 14. They seem to work properly.
View 1 Repliesim having an intel E2180 processor with 2 gb RAM and an nvidia 8400gs graphics card. Lately i installed Fedora 12 on my system and found that with default settings the desktop 3d is not working. so installed the kmod-nvidia using yum after following the instruction.i also edited the grub.conf file to rdblacklist=nouveau to blacklist nouveau drivers.
Then once i rebooted i found two kernels in grub ie the old one and the one with PAE extension. when i booted into the old kernel its Xwindows failed to load showing a black screen and when i tried the new PAE kernel it booted in 640 x 480 resolution. {earlier i was getting a resolution of 1440 x 900 on my 17" widescreen monitor}. it also showed that the nvidia drivers failed to load. I also read in some forums that the PAE kernels are for systems with 4gb+ of ram. So i thought it better to reinstall the whole thing.
then i reinstalled the whole operating system using my fedora 12 dvd and performed the 'upgrade or replace the existing linux distribution'. interestingly now my older kernel has disappeared and the PAE kernel is the one that is remaining.
[Code]...
I have a Dell Vostro 3300, i5 460 processor with a NVIDIA 310M Graphics Card. I'm doing a KUBUNTU 10.10 (Maverick) install with the following results. The Live CD boots just fine to, "TEST," or "Install." Installation goes fine. However, the graphics card being used is the Intel i915. I have tried installing the NVIDIA drivers directly from the, "Additional Drivers," tool and after the reboot I get through the boot screen to the console. I try to manually startx and I get the errors, "no device found," "no screens found." The second install I tried purging and blacklisting the nouveau drivers and entering safe mode. Then using apt-get install nvidia-current. After that, nvidia-xconfig. Same results.
The third attempt I re-installed and this time downloaded the drivers from the Nvidia site (version 256.53). Blacklisted nouveau, remove all nvidia, updated initramfs, etc. The install went fine however I still end up at a console after boot with the same messages as above. No device found, no screens found. I've tried searching through the forum and web and have tried things like adding the modset option along with many other hacks, tips and fixes. still, no go.I can live with the Intel graphics for now although I lose 512MB of memory. Unfortunately there is no way to disable or change this set-up in the BIOS. I've seen quite a few bug reports at Launchpad:
1. Is this something I should just wait til a fix comes? Will a fix come?
2. Is there, or will there be an official Updated Ubuntu Guide for Maverick to install NVIDIA drivers with this tecnology?
3. Lastly, is there anything else I should try??
I seem to have an issue with my nvidia drivers again.I get them working, then the next lot of updates to fedora seems to revert any progress I've made.Currently I can't run any 3d accelerated applications, no wine, no games etc, I have followed the documentation, installed the driver, added the blackist to noveau into boot.conf, and restarted
Code:
[james@nevada ~]$ uname -r
2.6.31.12-174.2.3.fc12.x86_64
[code]...
This is my first post, as I've finally become fed up with trying to get the nvidia drivers installed on Fedora 10. I've read through all the posts here about how people have had problems. I know about the rpmfusion repository, and have followed leigh123's instructions to the letter at this link:[URL]The exact stepsI have taken before following his sage advice follows this way: install off the CD image I burned of Fedora 10, run from the menus "System-->Administration-->Update System" to get the system up to date, reboot to make sure everything is working fine.
Then I follow the above instructions (only because they have gotten me the closest to getting the drivers working). After the reboot from following those instructions, the system starts up, and I have a desktop. But when I restart again, either because I'm shutting down for the night, or just to check again that everything is fine,I get nothing but a flashing cursor in the upper left of my screen. I'm able to CTRL+ALT+F2 and get to a login that way, but can't get into the GUI. I've searched the forums (both here and on The Web generally), and can't find a fix for this that works for me. I have gone back and erased the partition and reinstalled, so I'm at the basic install with all the updates for my system, and needing help with getting the drivers installed and working.
Just to give a run down of what I have on my system:Two NVidia 8500 GT cards connected with the SLI bridgeAMD Athlon 64 X2 Dual Core 3800+Runningl 2.6.27.12-170.2.5.fc10.x86_64 (I'm typing this up as I reinstall updates as I listed above).Before anyone starts giving suggestions, please make sure to give the full instructions, as I'm new to Fedora/Linux. And if there is anything else you wish to know about my configuration
Today I finally could install Fedora 15 i686 in my now aging (2005) desktop computer (although I will always think of it as my "new machine", as long as I don't assemble a new one for me):
AMD Sempron 3100+ (1.8GHz)
1GB DDR400
120GB HDD
NVIDIA GeForce FX5200 (128MB)
After I installed F15 my initialpression was that it worked really good on that hardware: everything went fine with GNOME 3 for example,except for some lags in graphics rendering, which I thought would be solved after the graphics card's full power were unleashed with the proprietary NVIDIA driver.For starters I am not sure which Nvidia driver is right for my card (Nvidia 173.X or the regularvidia).I managed to get "working" the 173.X driver but the desktop is even less responsive to begin with, and there appears to be a lot of activity on the hard disk side.So, my question is, which could be causing the performance loss?
A. The "small" RAM.
B. The vintage graphics card.
C. Some problem in the hard drive.
D. A known bug.
opensuse 11.2 ,my monitor keeps going to sleep or somthing and this is a problem when im watching videos,ive set screens power setting but they dont seem to be whats doing it.im running a nvidia gtx260 and have installed nvidia drivers for series 6 and up.dont know if its the divers or somthing else.
View 9 Replies View RelatedI'm trying to install the drivers for my nvidia graphics card. I downloaded the shell script from the nvidia website. However, there's something peculiar going on. When I execute the shell script it says it cannot find my kernel headers, yet I can verify that my /usr/include/linux/kernel.h does exist. I have selinux on, but just installed os with it on, so contexts are fresh. Checked them as well. After doing some research I found something out. When I run a 'uname -a' I get this.
Code:
Linux ariel 2.6.18-194.el5PAE #1 SMP Fri Apr 2 15:37:44 EDT 2010 i686 i686 i386 GNU/Linux
Yet when I ran 'yum install kernel-devel kernel-headers' they installed the following versions.
Code:
kernel-headers-2.6.18-238.12.1.el5.i386
kernel-devel-2.6.18-238.12.1.el5.i686
Shouldn't they be
[Code]...
I see that the error in the nvidia shell script can't locate the header files for the RUNNING kernel version which makes sense. Why would yum install that version instead of the one in 'uname -a'? Or am I misunderstanding something?
I attempted to install restricted drivers using jockey-gtk, was told to reboot and drivers would take effect. Rebooted and got no graphics, after some finagling I was able to delete xorg.conf and I now have horrific looking graphics. Defaulted to current version or 195 (which is also the only option I see in the jockey tool, however in synaptic/apt I see I can install other versions.
View 5 Replies View RelatedI have a problem with starting ubuntu 10.10, I changed my graphics card from an ATI card to a Nivida card a week or so ago (Machine has dual boot). I've sort out the windows install, but cant get into ubuntu to update the drivers. It boots as far as console but just leaves me with the text screen. How do I update the drivers from there or get a basic console screen to come up so I can update?
View 1 Replies View RelatedI accidentally installed ATI graphics drivers on an intel graphics system. They didn't appear to install properly, because upon next boot everything was fine, except for compiz and any 3d game.
compiz-check says that I've managed to get intel back as default, but I'm still missing a rendering method.
Does anyone know how to get the renderer back? I assume it has something to do with changing the kernel? I don't know how to change the kernel anyway.
First off, I'll come clean and admit that I am still relatively green to Linux, but I'm not afraid to tackle the complex. I have a few stroke-inducing issues that I haven't been able to resolve as a usually do by eye-grepping Google and the various forums. Of course, I'm running Ubuntu 11.04 with Unity - which is fairly new and undiscovered country.
I've got this no-name brand, sample laptop from a manufacturing partner of ours out of Shenzhen China. It's rocking a Core i3 M350 with an nVidia GT 330M (discreet-ish?)& apparently some flavor of Intel integrated graphics.
Now, there are so many variables at play, I'm not quite sure where to begin - so please bear with this post a bit longer as I unravel the details. Loading the nVidia drivers (both proprietary and the experimental open varieties) results in Unity no longer working and dumping me back to the classic Ubuntu desktop. I believe it has something to do with the fact that I have no ability to disable the integrated graphics through the BIOS and Ubuntu has set its hopes and dreams upon using Intel graphics for the rest of all time.
That said, running without the nVidia graphics drivers, I am able to use Unity and it runs pretty well.The only caveat being that on occasion (read: intermittently), when the laptop wakes up from suspend/hibernate mode, playing Flash video in full screen gets choppy (stutters). Restarting Ubuntu resolves the issue. I suppose I should verify that I am using Firefox 4.
In addition, there are times that the WiFi adapter will not wake, and using the keyboard function key to power cycle it ceases to function. A complete shutdown is required to address this one. i.e. Restarting and warm-booting does not fix it.
Did I mention Skype is a terd? I don't actually expect a fix for this pile of hot mess - just thought it might make someone laugh. If there is anyone here that could lend me a hand with any or all of these issues, not only will you have the satisfaction of knowing that you are one bad Mambajamba (TM), but I'll buy you a drink or something via Dwolla or bitcoin.
As this question pops up quite often on IRC and, as a quick search told me, on this board as well, I decided to put together some directions that, with some or the other variation, also apply to other Linux distributions and have never failed me. The following is confirmed to work for Kubuntu 11.04 Natty Narwhal 64bit with a NVIDIA GeForce GT 240 and on Kubuntu 11.04 Natty Narwhal 32bit with a NVIDIA GeForce FX 5900XT graphics card.
This HowTo will describe how to install the proprietary NVIDIA graphics card drivers using exclusively the command line. I strongly suggest you try this method for a fresh install of graphics drivers before trying any other method, especially a GUI-driven one (I never used a GUI for package management on a Debian-ish system, but I hear that the Ubuntu Software Center supposedly has a way of installing proprietary graphics drivers).
The restricted packages repository should be enabled by default. To the more experienced users: This HowTo uses apt-get for demonstrating the install process. If you prefer using aptitude, feel free to replace the commands accordingly. First steps. As well be doing everything on the command line, first open a terminal application from your desktop environments menu or from a shortcut icon on your panel, if you have one. You should be greeted by a prompt that looks like this:
[Code]...
I have just installed Kubuntu 9.10 in my laptop and it did not ditected my Nvidia 8400 M GS graphics Card I downloaded a driver file
NVIDIA-Linux.x86-19042-pkg1.run to install drivers but when i run it it shows the error error:you appear to be running X server, please exit X before installing.
I'm going about my ways to get my drivers installed for my graphics card, but the page I'm using, URL>..has me apt-get install "nvidia-kernel-common".Synaptic says it doesn't exist, and it appears to be a pretty important package to have. So is there a way for somebody to get that online for me to install?
View 5 Replies View RelatedI just got a free Ubuntu 9.04 desktop cd in the mail today, but I'm already having a problem.
I'm using Ubuntu 9.04 Desktop 32 bit. I need graphics drivers for playing video games such as Nexuiz. My graphics hardware is in ATI Radeon X1200 series. The fglrx driver I downloaded from ATI does not install.
When I use code...
Completely new to Ubuntu, basically never used anything but Windows before, hadn't even had a chance to properly test out Ubuntu before I broke it. So, sorry if this question is very easy...or if I'm posting it in the wrong place...
Anyway, I cleverly installed the most recent drivers for my graphics card, and it killed Ubuntu - it won't start now. This happens on Windows, too, but Windows will System Restore for me. How might I fix this in Ubuntu?
I can choose Ubuntu from the grub menu, but then the screen goes blank, the fan on my computer goes into overdrive, and nothing happens.
Am currently running my Karmic Koala from LiveCD...
When i was on the live cd installing ubuntu it said i could install my driver but now that i am running off the hard drive it doesn't pick it up under "Hardware Drivers"
View 3 Replies View RelatedI'm installing 10.4 fresh but I can't get the Nvidia drivers installed. I'm using a 9400 GT. Ubuntu installs normally but when I try to enable to the proprietary driver, I get an error on reboot "Failed to initialize NVIDIA graphics device" and have to restart X. Any suggestions on how to get this working?
View 9 Replies View RelatedI've just installed the brand new Ubuntu 11.04 and all goes well until...I log in a session. There is a window telling me that my graphic card isn't too good to run Unity, when I have no problem under 10.10 to run all the eye-candy. Now I have a NVIDIA Quadro NVS 120M with 512 megs of memory. I've install the NVIDIA current driver in the Additional Drivers application and reboot. But nothing...in the additional driver app it says that the current driver is installed but not currently in use...what should I do before giving up and install unity-2d?
View 2 Replies View RelatedI want to run both World of Warcraft and Steam under wine, but WoW won't work with the latest 195.x.x driver, and steam won't work with the previous 185.x.x driver.
Is it possible to have both installed, and to switch between them as needed for different applications? Or will I really have to choose between one or the other?
i have just installed opensuse 11.3 on my PC and updated all packages and all and then i installed nvidia drivers from this link SDB:NVIDIA drivers - openSUSE i downloaded the 1 click install file nvidia.ymp and installed the driver successfullybut then when i rebooted the PC for the driver to work,it doesn't work,and when i go to system>look and feel>desktop effects and i try to enable the effects i get the message that i cant enable the effects it gives me this message "Desktop effects are not supported on your hardware / configuration. Would you like to activate them anyway?" PS i say "no" to this message and it closes but i notice there is a constant use of 33% of the CPU and theres an unnamed/unknown process in the system monitor that keeps appearing and disappearing...thats quitrd because i installed opensuse 11.2 and 11.3 before and i never had these problems
View 3 Replies View Relatedi have a viewsonic VA712b monitor that used to get 1280x1024 resolution on my dell optiplex gx260 that had the intel video card.i upgraded my motherboard cpu and memory..the nvidia 6100 that is onboard seems like it would be an improvement to my old onboard intel but the best resolution i can get is 1024x768
i installed the nvidia 185 drivers and it's not recognizing my monitor as a flat panel lcd but as a crt, also it won't set the correct refreshrate - either 60 or 75.. it's set at 50... since xorg 7.4 no longer uses a xorg.conf file.. i'm not sure how to go about manually adjusting the settings to ones that will actually work. i mean other than buying a separate graphics car (URL)
After installing ubuntu 64 bit, I installed all my updates and installed the current nvidia driver for my 9800 GTX+ from the additional drivers page. After restarting my computer, ubuntu boots into text mode. I used google and found out a couple of commands like:
After i hit control+alt+f7 it hangs on checking battery state with NO ok to the right of it. after running sudo apt-get --purge remove nvidia -current and restarting the computer, the boot hangs on the ubuntu screen everytime.
My specs are:
Core i7 860
4 GB of ram
Nvidia 9800 GTX+
[URL] I just updated and then saw this news , whats the solution for me, I either want to go beta or downgrade, If i try to boot to previous kernel, boot hangs in graphic mode, I cant start X and gdm . How to install kmod with beta drivers? Or whats the solution, nvidia ver: 195.36.08
[Code]....
I've tried to install nvidia drivers using this commands:
Quote:
yum install kmod-nvidia
yum install akmod-nvidia
yum install nvidia-xconfig
After rdblacklist=nouveau in grub it runs, but I am having several issues and therefore I would like to downgrade to nouveau or whatever I had running with basic fedora 12 installation.
My GPU is nvidia gtx 280:
Quote:
[root@localhost ~]# /sbin/lspci | grep VGA
01:00.0 VGA compatible controller: nVidia Corporation GT200 [GeForce GTX 280] (rev a1)
My kernel is:
2.6.32.9-70.fc12.i686
I Have just formatted to Fedora 14 64bit and installed kmod-nvidia akmod-nvidia and am experiencing visual lag. The lag did not occur before I installed the drivers, neither did it occur on Fedora 13 with drivers installed.
I have a priitty high spec pc with the nvidia 260 gtx.
just remove xorg-x11-drv-nvidia-libs-260.19.12-3.fc14.i686
so now:
I installed fedora 11 yesterday, and didn't get time to do anything else. And the first thing I did today was to install the nVidia graphics drivers. But after I rebooted the loadings screen comes up (the one with 3 loading bars) and then it's just a black screen with a blinking _
View 4 Replies View RelatedMy workplace is conducting a pilot of fedora15 for adoption as our SOE desktop. We've installed on 3 desktops and two laptops, and are experiencing an intermittent lock-up on each platform. In all cases so far over our two week trial, whilst users are performing routine work on the gnome desktop (e.g. email, web browsing, etc), the screen will freeze, and the mouse/keyboard appear to be inoperable, so it is impossible to go to a virtual desktop, etc. Only a hard reboot brings the PC back, and there are no logs, core dumps, etc.
We've been trying to eliminate sources, and have seen the fault on the following combinations:
* AMD/Intel
* A variety of graphics hardware (e.g. nvidia, intel 945)
* nvidia drivers (various versions), and nouveau
* Gnome 3 in normal and fallback mode
* rpms from the initial F15 release, and also after a full yum update (last week).
We have not been able to correlate the lock-up with particular usage patterns or system load. Sometimes, the desktop will be usable for a day or more, and other times, we may see three lockups in an hour.
There is a bug on this matter:
[URL]
I am raising the matter here to see, because I am puzzled as to why we are experiencing it on all platforms, and yet it does not seem to be so prevalent in the wider community.
I have just installed Ubuntu (9.10) and noted that in order to successfully run the trial off the CD I had to test in "safe graphics" mode. I have an NVIDIA GEforce 6600 GT card - which was discovered by Ubuntu in the first few minutes of the trial and so I activated the recommended driver and continued to test. After a successful trial I installed Ubuntu (dual partition Ubuntu / Windows XP), however, it seems the install didn't activate the required driver (as part of the process) and so I'm unable to get into my newly-installed Ubuntu at all. All I get is a flashing tty screen asking for my username and password - however it's erratic and won't recognise what I type. So - I'm stuck in a catch-22 as there doesn't seems to be a safe graphics mode option via the start (GRUB?) menu list.
View 4 Replies View Related