Ubuntu :: WLAN Is Not Found?
Oct 22, 2010
my netbook doesn't see my HomeWlan, but like every other int he neighborhood. I am using a live-usb atm because i want to check if everything works out bevor i completely install ubuntu.
Details: I want to use my home-WLAN but Ubuntu doesn't see it, which is quite fascinating because it does see a bunch of other which belong to the neighbors. The second quite interesting part is that when i switch to windows i can connect without any problems (and yes it does see it as well). Any clues what might cause that behavior? My only guess is that the adapter broadcasts on a false Channel, but i aint sure about that. I entered "sudo iwlist chan" and the output is:
Code:
lo no frequency information
eth0 no frequency information
eth1 14 channels in total; available frequencies :
//bunch of frequencies
current channel 1
So i guess my adapter broadcasts on channel 1, but my router does on channel 6 (I am sure about that part). But when i tried to "fix" it with "iwconfig eth1 channel 6" and then i check the channels again, it is still on the same on (Channel 1). Well, i do have a second guess but this one seems even more unrealistic than the first one, it might be possible that my adapter isn't strong enough to get the signal, even though there are just like 2 1/2 Walls between. But this scenario is really unlikely because my netbook is getting so much other signals.
View 7 Replies
ADVERTISEMENT
Apr 19, 2011
I have recently bought a new laptop (medion akoya p761 and I can't get the wireless working... With windows 7 it's working.
I followed the sticky guide but still no success....
The problem is in the first place that it doesn't list my wlan : lspci -nn
Code:
:~$ lspci -nn
00:00.0 Host bridge [0600]: Intel Corporation Core Processor DRAM Controller [8086:0044] (rev 18)
00:01.0 PCI bridge [0604]: Intel Corporation Core Processor PCI Express x16 Root Port [8086:0045] (rev 18)
[Code].....
View 9 Replies
View Related
Nov 27, 2009
There is no wlan0 interface when trying to run FRITZ!WLAN USB Stick N 2.4 on OpenSuSE 11.2, though it works fine on Fedora 11 and Mandriva Spring 2009.1. All 64bit. Contrary to Fedora and Mandriva, there is no need to compile the compat-wireless module ar9170usb for OpenSuSE 11.2 because the kernel is very recent and includes this driver. Kernel: 2.6.31.5-0.1-desktop The /var/log/messages gives this after I put the stick in the PC. At first it is seen as a mass storage device:
Nov 27 22:00:24 linux-3mwa kernel: [ 73.420755] usb 1-5.1: new high speed USB device using ehci_hcd and address 4
Nov 27 22:00:24 linux-3mwa kernel: [ 73.540834] usb 1-5.1: New USB device found, idVendor=057c, idProduct=84ff
Nov 27 22:00:24 linux-3mwa kernel: [ 73.540841] usb 1-5.1: New USB device strings: Mfr=16, Product=32, SerialNumber=48
Nov 27 22:00:24 linux-3mwa kernel: [ 73.540847] usb 1-5.1: Product: FRITZ!WLAN USB Stick N 2.4
[Code]....
View 5 Replies
View Related
Mar 29, 2010
I have been trying to get this web cam working for a long time. lsusb:
Code:
Bus 004 Device 003: ID 06a2:0003 Topro Technology, Inc.
dmesg
Code:
[ 1990.570050] usb 4-1: new full speed USB device using uhci_hcd and address 3
[ 1990.751460] usb 4-1: configuration #1 chosen from 1 choice
Kernel patch: [URL]
Driver project: [URL]
Cheese simply says no camera found. Skryba says no devices found. Since this kernel patch was 2009-04-07 which is nearly a year ago it should be in latest kernel?
[Code]...
View 3 Replies
View Related
Jan 24, 2010
During install of 9.10 server, both ethernet adapters were found. One is built-in to the motherboard, the second is on a PCIe slot. Selected the on-board adapter for eth0 during install, set fixed IP on the web, connected, updated, etc. w/ no problems. The second adapter is for the LAN.BUT, on first and subsequent reboots after installation complete the second adapter is not detected at all, as if it were not even plugged into the PCI or the driver not loaded. This happens on either of two slots, with two different adapters, Intel or Netgear, both pretty recent, and both of which are detected and work in a different box. 'Ethtool eth1' says device not found.This is a fairly recent motherboard 3N78EM).Since the adapter was found during installation I'm assuming that the problem is not with not the board. I've built several server systems with two or three ethernet adapters and have never run into this situation.
View 3 Replies
View Related
Oct 1, 2010
I installed a program with Yast (Kmess), but when I try to run it, bash gives me back this message:
Code: kmess: command not found I checked into Yast and it seems to be installed correctly!
View 9 Replies
View Related
Jun 13, 2010
I installed several desktops on my system to test them out recently. After that I did an update and the system proposed to autoremove some files that were not used anymore. Since then, I can't connect to the internet from any of my desktop environments. In GNOME, the wireless network applet completely disappeared, the same thing with KDE, so I'm thinking a system driver must have been deleted. Could you indicate me any file that I might need to download to repair this problem?
View 1 Replies
View Related
Feb 6, 2010
At my workplace the wireless connection is open but once you connect you first need to authenticate on your browser to be able to use the internet.On Windows as soon as I open whatever page I get the login request.On Linux I open firefox but nothing happens, just get the usual error page like if I had no connection. The IP's I get as well as DNS seem ok, I even tryed to match them up with windows.I tried a lot but can't get to the login page.
View 3 Replies
View Related
Apr 23, 2010
in my work computer i put ubuntu, i had to install the version8.4 then i had to upgrade one by one to 9.10 because the computer was not able to detect it via a usb live instalation. in my wlan signal when i had 8.4 it had the 4 stripes that mean the signal was like 90% but every time i upgraded the signal became weaker, and now that i upgraded to 9.10 the signal is 14% it takes forever to DL the updates and aplications. and the connection is 2mbps
i have a really old laptop a toshiba sa30-3-3 with 512 in ram and a pentium 4 a3.06ghz.
does anybody have an idea of whats going on and how to get ti fixed.
View 2 Replies
View Related
May 23, 2010
specific Ubuntu supported WLAN PCI-cards? This link shows a list of supported PCI-cards, but which is best: [URL] And the installation needs to be easy! I�ve tried installing these PCI-cards in my computer, useing Linux drivers, NdisWrapper, etc. Unforutately without any success:
- DWL-G510, Ralink Chipset, Ralink RT2561/RT61
- Realtek Semiconductor, RTL-8185 IEEE 802.11a/b/g Wireless LAN Controller
View 1 Replies
View Related
Oct 25, 2010
I remember a few months ago I attempted to install Ubuntu 10.04 on my Dell laptop however the Dell 1397 internal card wasn't recognized which was a huge problem. I posted here & nobody responded. Now before I try and install 10.10 on my laptop, is there a way I can verify that my WLAN card will be recognized by the kernel or is it the same thing as 10.04?
View 2 Replies
View Related
Oct 25, 2010
I've decided to try out Ubuntu again on my Samsung netbook. I tried 9.10 before and a lot of things didn't work so I gave up, but that was quite a long time ago and I wanted to see if the new one will work.
I booted 10.10 off the USB stick, don't want to zap my Windows 7 installation if Ubuntu doesn't work. Everything seems to run fine, the webcam works, wireless seems to work, it shows the networks in the range and allows me to pick the one I want to connect to.
Sounds good so far, but when I try to connect to my WLAN and put in my password it thinks about it for a while and just pops the password again. It can't seem to connect to the network even though it sees it and the password is correct. I triple checked the password, it's definitely correct.
I can only assume there's something wrong with ubuntu and the driver. I have a Samsung N140 netbook which uses Realtek 8192E chipset.
View 1 Replies
View Related
Apr 29, 2011
Today I upgraded from 10.10 to 11.04. After accidentally turning off the computer during the upgrade, booting into recovery mode, remounting the file system as writable and finishing the upgrade, it worked just fine.
However, I can no longer use any wireless networks. Wired ethernet works fine, but the wireless inteface won't even show up when I run ifconfig. When I first installed 10.10, it worked instantly and I was able to use it during installation.
I have an HP Compaq nx7300 laptop with a Broadcom BCM4311 network card.
View 1 Replies
View Related
Jun 12, 2011
I installed 11.04 to ASUS Z9200 Notebook, at first all was fine at least 10 minutes, LAN, WLAN worked ok, but suddenly all is gone, restarted few times -nothing. reintall-nothing...here is some info....any ideas?
mm@mm:~$ sudo lshw -c network
[sudo] password for mm:
*-network:0 DISABLED
description: Ethernet interface
product: 88E8001 Gigabit Ethernet Controller
vendor: Marvell Technology Group Ltd.
physical id: 0
[Code]...
View 1 Replies
View Related
Jul 29, 2011
Guys its my second post coz the first one didn't neither LAN or WLAN seem to workon typing.........sudo lshw{Content trimmed}
*-network
description: Network controller
product: BCM4311 802.11b/g WLAN
[code]....
View 6 Replies
View Related
Aug 13, 2011
I am connected to my wireless router (wlan0) i'm also connected to my laptop via cable (eth0) wlan0 has the internet connection, if i disconnect eth0 i can browse internet but if it's connected, i cant eth0 has manual address: 192.168.0.7 wlan: auto (right now:182.168.0.255)
View 9 Replies
View Related
Mar 30, 2011
I have a Fujitsu Siemans AMILO Li 2727 and have tried and like Linux Ubuntu. My problem is I have an internal ariel that switches off when you power down. It has to be manually switched on by pressing function F1. I can't get this to work in Linux - I want to be able to use my laptop with my wireless router again.
View 3 Replies
View Related
Jun 30, 2010
I have a Thinkpad T400 notebook that dual boots windows 7 and Ubuntu 9.04. My wireless has worked both in windows and ubuntu for the past several months. However 2 days ago, the wireless in ubuntu stopped working. I think this may be a result of trying to set up a static eth0 connection between my laptop and an embedded board, but I dont see how messing with eth0 would stop the wlan from working.
Symptoms: When I left click on the network connections icon in the tray, all it lists under "Wireless networks" is "device not ready". Needless to say, there are no networks available to connect to. Also the wireless is working fine under windows.
[Code]...
View 1 Replies
View Related
Aug 10, 2010
I have bought a new laptop with win7 on it , I delete win7 and install ubuntu64 everything is ok but my wireless card won't work ( it is recognized) and even I can connect to INTERNET but nothing is download or upload so I have bought another usb wireless card but now when I connect this new card to my laptop it still tries to use the old one and so I could not connect to internet
View 4 Replies
View Related
Aug 18, 2010
I am trying to connect to a WEP encrypted WLAN without using the DHCP server of the AP. (=giving myself a static IP)
So far i have tried:
Code:
But i cant even ping 192.168.1.1 (Network unreachable error). Is it possible that Ubuntu tries to use eth0 (which was connected to a similar /16 before) to ping 192.168.1.1 or is there somethign wrong with my commands?
Also will an AP allow access to the network although i don't have an IP from its DHCP server?
View 3 Replies
View Related
Sep 2, 2010
I can connect my wlan card to router (gateway) ,but I can't go to internet, pinging my router (and everything else) also falied. Same problem was with knoppix but with help of others i solved it modifing etc/reslove.conf IP address to my gateway (nameserver). At ubuntu resolve.conf seems ok, as there is already IP address of my gateway?
View 6 Replies
View Related
Nov 8, 2010
All I want to do is share my internet connection that comes through the eth0 cable to my wlan0 wiki card. Firestarter seems the convenient tool for doing this. BUT it keeps telling me wlan0 not ready. The card is connected correctly and network-manager does see incoming signals.
View 1 Replies
View Related
Nov 19, 2010
I have installed Ubuntu 10.10 on my intel macbook. It won't ever find any wifi internet connections. It will connect with an ethernet fine but none of the wireless connections will show up.
View 1 Replies
View Related
Dec 25, 2010
I'm a new user of Ubuntu and I think I need some help but let me mention before that I got this up working on a Debian system.My current kernel version is $ uname -r 2.6.32-27-generic.The problem is that my wlan card is not working any more such that my system freezes every time I enable networking with the hardware switch on my laptop.Therefore I bought a USB - WLAN stick and try to get this working.
Network Manager has the option "enable wireless" greyed out if I disable the hardware switch.If I enable the hardware switch and remove the module of my wlan CARD before (modprobe -r iwl3945) it says "wireless disconnected" for all networks.
View 1 Replies
View Related
Mar 8, 2011
I am very new to Ubuntu and I need some help. My HP Pavillion WLAN light constantly blinks as it recieves data on the internet and I learned that I have to create and save a file: "sudo nano /etc/modprobe.d/wlan.conf" and then paste the following at the end: "#1 means do not blink options iwlcore led_mode=1" but when I try to save it asks me for my sudo password which I don't have and it does not even register any key I press. It just blinks but does not acccept any key. Also how do you save the file in terminal?
View 3 Replies
View Related
May 1, 2011
anybody out there with an idea for a command to make the WLAN-Printer (HP-Officejet)work again when it stops after 30 Min - 2 h.Simple stopping the print job and print again does not help. The only way for me is to stop the print job and RESTART. Then it works again 30 Min- 2 h. I use updatet lucid lynx 32.
And I need a command like "killall pulseaudio" that I need when I return from logged-on as the second user to get sound again.
View 1 Replies
View Related
Jan 12, 2010
I have just installed Ubuntu 9.10 on an Acer TravelMate 290E. I've got internet connection through the Ehternet Cable, but when I plug in the D-Link WLAN USB device, although the system recognises it, it is disconnected. How can I connect the WLAN USB device adn get it to work?
View 5 Replies
View Related
Jan 16, 2010
my network was a dream to set up under ubuntu 9.10. all i had to do was enter pass key, then that was it. Works brilliantly.
Different matter with studio. The thing I notice in network connections is, it doesn't want to retain my pass phrase, if I go back into properties the phrase is blank. As far as I can tell the wireless card has been reconcognized and is communicating with router.
My system is: asus p5ql-vm epu, intel core2 duo 2.8 e7400, 4gb 1067 ddr2 ram, belkin f5d7050 v4000, edimax router.
Here is the info requested in the sticky:
kevin@ubuntu:~$ lsusb
Bus 007 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 008 Device 003: ID 045e:00dd Microsoft Corp.
Bus 008 Device 002: ID 046d:c501 Logitech, Inc. Cordless Mouse Receiver
Bus 008 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
code....
View 3 Replies
View Related
Feb 21, 2010
On my HP TX2500 laptop, dual-booting Vista and 9.04, Ubuntu installation found the WLAN and it works fine.I installed VirtualBox with Vista as the host and 9.04 as the guest. Wired Ethernet works fine but it didn't seem to find my WLAN. What more do I need to do?
View 1 Replies
View Related
Mar 29, 2010
I am new to using ubuntu. I am trying to play with my WLAN by changing its modulation, power, bitrate, channel etc. When I am trying to change the modulation type i had an error like this # iwconfig wlan0 modu 11g Error for wireless request "Set Modulation" (8B2F) : SET failed on device wlan0 ; Operation not supported. so i checked for different modulation types my WLAN supports this produced an error like this.
# iwlist wlan0 modulation wlan0 unknown modulation information. I even cannot access the power types my WLAN supports. I am using Intel wireless wifi link 5100. change the modulation type and power for my WLAN?
View 3 Replies
View Related