Guys its my second post coz the first one didn't neither LAN or WLAN seem to workon typing.........sudo lshw{Content trimmed}
*-network
description: Network controller
product: BCM4311 802.11b/g WLAN
[code]....
I have Karmic Koala 9.10 working (near) perfectly on my iMac7,1, as identified by
Code:
NOTE: See below for Lucid 10.04 update to these instructions
IMPORTANT: You need to complete the installation procedure while connected to internet via the WIRED network. Then you can enable the wireless by installing the restricted drivers, after the install is complete. Also the fglrx ATI Video driver is effortlessly installed via Menu > System > Administration > Hardware Drivers
The sound card gave me some trouble, as it is an Intel HDA Model, reported as 'Codec: Realtek ALC889A' by
Code:
It shows up in lspci as:
Code:
It sounded rather tinny at first, when I tried mbp3 and other model names. Then I added the following line to /etc/modprobe.d/alsa-base.conf :
Code:
After reboot, my sound is full and can be put much louder than before. Jack detection works. Some people might have to leave out the power saving options. See below.
dmesg reports:
Code:
Sources consulted are mostly the kernel documentation ( Enter into the terminal: sudo apt-get install linux-doc
The relevant info can be found in HD-Audio-Models.txt.gz and HD-Audio.txt.gz in /usr/share/doc/linux-doc/sound/alsa )
I have a Thinkpad T400 notebook that dual boots windows 7 and Ubuntu 9.04. My wireless has worked both in windows and ubuntu for the past several months. However 2 days ago, the wireless in ubuntu stopped working. I think this may be a result of trying to set up a static eth0 connection between my laptop and an embedded board, but I dont see how messing with eth0 would stop the wlan from working.
Symptoms: When I left click on the network connections icon in the tray, all it lists under "Wireless networks" is "device not ready". Needless to say, there are no networks available to connect to. Also the wireless is working fine under windows.
[Code]...
I'm a new user of Ubuntu and I think I need some help but let me mention before that I got this up working on a Debian system.My current kernel version is $ uname -r 2.6.32-27-generic.The problem is that my wlan card is not working any more such that my system freezes every time I enable networking with the hardware switch on my laptop.Therefore I bought a USB - WLAN stick and try to get this working.
Network Manager has the option "enable wireless" greyed out if I disable the hardware switch.If I enable the hardware switch and remove the module of my wlan CARD before (modprobe -r iwl3945) it says "wireless disconnected" for all networks.
I have just installed Ubuntu 9.10 on an Acer TravelMate 290E. I've got internet connection through the Ehternet Cable, but when I plug in the D-Link WLAN USB device, although the system recognises it, it is disconnected. How can I connect the WLAN USB device adn get it to work?
View 5 Replies View RelatedI have a desktop and laptop both running ubuntu 10.04. I have them going through a wireless router, the desktop is wired of coarse. I installed just about all the samba packages in synaptic that have the little ubuntu symbol next to them on both desktop and laptop except the Kde and document packages. I installed the two necessary packages to enable personal file sharing to work. But I can't seem to access files back and forth from these computers.
View 5 Replies View RelatedI have recently bought a new laptop (medion akoya p761 and I can't get the wireless working... With windows 7 it's working.
I followed the sticky guide but still no success....
The problem is in the first place that it doesn't list my wlan : lspci -nn
Code:
:~$ lspci -nn
00:00.0 Host bridge [0600]: Intel Corporation Core Processor DRAM Controller [8086:0044] (rev 18)
00:01.0 PCI bridge [0604]: Intel Corporation Core Processor PCI Express x16 Root Port [8086:0045] (rev 18)
[Code].....
I have hp dv6291 laptop with Centos 5.2 os the NIC & WLAN not working ?
View 2 Replies View RelatedInstalled F14 on my daughters HP Pavilion a131On. I rebooted multiple times. Do I need to activate something? I'm new to all of this but read through many threads to do as much as I could myself. I used the GUI to load the rt3070 drivers rather than rpm. The GUI is easier I think and should be equivalent. Please let me know what else I need to do. Fedora has been great on my Lenovo but this usb wlan stuff has been a pain.
[Code]...
I'm running Fedora 15 KDE on a Sony Vaio VPCS13V9E. No problems in connecting to the wlan. Today I upgraded the system. There was an upgrade for Network Manager. After the upgrade the system is not able to connect to the modem - router (Linksys WAG320N) any more. Network manager keeps on crashing and sends messages like "network disabled" or "connection failed". Kde demon is reporting errors too. I guess the new version of Network Manager is bugged, because before the upgrade it did work well ... (unbelievable!).
lspci: 02:00.0 Network controller: Intel Corporation Centrino Advanced-N 6200 (rev 35).
Subsystem: Intel Corporation Centrino Advanced-N 6200 2x2 AGN
Flags: bus master, fast devsel, latency 0, IRQ 44
Memory at dd100000 (64-bit, non-prefetchable) [size=8K]
Capabilities: <access denied>
Kernel driver in use: iwlagn
Kernel modules: iwlagn
I have upgraded from Fedora 14 to Fedora 15. Fedora 15 looks very good. Now my 'Bluetooth', 'Wlan' and 'WiMAX' are not working.
View 2 Replies View Relatedafter I upgraded from opensuse 11.0 to 11.3 the wlan doesn't work anymore. following the rules, how to post the trouble. I also updated the correct FW. What's wrong? packet missing?
Code:
# lspci
...
03:00.0 Network controller: Intersil Corporation ISL3890 [Prism GT/Prism Duette]/ISL3886 [Prism Javelin/Prism Xbow] (rev 01)
# dmesg
[code]...
I'm using Ubuntu 9.10 on a Lenovo ThinkPad T61 using an Intel PRO/Wireless 3945ABG. My laptop's ability to connect to a wireless network stopped last night, and I'm not sure why. It's definitely something on my end, as my roommate can connect to the internet on a Windows box. I can wire in without a problem, but that's a pain and my Ethernet cable got lost in the shuffle when I moved back to school. I've been able to get into this network before and nothing about it has changed. I've been able to hibernate and restart and such and nothing has ever needed to be reset.
The router's a D-Link WBR-2310. Wicd and Network Manager see the network (I'm back to using wicd) , but wicd appears to get stuck at "Obtaining IP address..." and says "Unable to connect: Cannot obtain IP address". I know my password is correct (I set up the router and I'm the CS undergrad in the apartment so I manage it), lspci sees the wireless card, ifconfig and iwconfig return information about the interface, dmesg|grep wlan0 doesn't seem to have anything terribly out of the ordinary, but here's that output:
Code:
allyanncah@taliesin:~% dmesg | grep wlan0
[ 23.514202] ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 36.609016] ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 38.756143] wlan0: direct probe to AP 00:24:01:cb:4e:7e (try 1)
[ 38.758791] wlan0: direct probe responded
[ 38.758796] wlan0: authenticate with AP 00:24:01:cb:4e:7e (try 1)
[ 38.760587] wlan0: authenticated
[ 38.760609] wlan0: associate with AP 00:24:01:cb:4e:7e (try 1)
[ 38.763318] wlan0: RX AssocResp from 00:24:01:cb:4e:7e (capab=0x431 status=0 aid=1)
[ 38.763322] wlan0: associated
[ 38.765502] ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready .....
I've tried:
- reinstalling wicd
- uninstalling wicd and installing network-manager
- restarting
- shutting down and booting back up
- restarting the router
- sudo /etc/init.d/networking restart
- taking the interface down and back up with ifconfig
I haven't changed anything recently in regards to my wireless card, and all the fixes I've tried are things I've done before without an issue. The only thing I'm wondering about is if doing a hard reset might have broken something (I know this is a cardinal sin, but there's a whole 'nother problem I haven't been able to fix with the OS hanging every once in a while over a VPN daemon when it tries to shut down or restart -- I've left it for hours to see if it actually gets anywhere and no luck, won't do a soft reset). I'm nervous about reinstalling the driver just because I've never had to do it and drivers are a finicky business. I imagine there's a config error somewhere?
My problem with UBUNTU is that I can not use acer-wmi because I get this ERROR :
Code:
... so I can not use the acer_wmi . But this is not my only Problem :
It is most likely caused of the missing " Firmware " / Driver for my WLAN Card ( Internal ) . Currently I use Ubuntu 10.10 but I tested 10.04 too before 10.10 and it found my Card but not the Button .
So I want to know if there is any solution for my problem .
If it is important :
I use an Acer eMachines e525 with Windows Vista Home Basic ( Pimped up ) and Wubi . I saw a lot of people with simmilar problems they have it as only boot option .
I updated Ubuntu to 10.04 after which I noticed the wireless indicator lights on my HP laptop were continually flashing between blue and orange and network performance seemed slow. I did some searching and found and implemented the following change to stop the flashing:
gksudo gedit /etc/modprobe.d/wlan.conf
Copy and paste the below line:
options iwlcore led_mode=1
Since making this change the wireless connection is shut off and I can;t get it to work at all. I first tried simply to remove the change to get back wher I was, but I can;t do that. Can sopmebopdy toell me at least how to get rid of this wlan,conf file ( it was created by the above command) so I can start over?
Coincidentally since making this change my Windows Vista OS fails to start because of errors attributed to a software or hardware change, of which there were none other than the Ubuntu wlan.conf change. . It may be unrelated but I am suspicious of the coincidence. I am running Vista and Ubuntu in a dual boot configuration and all ha run very well until I did the Ubuntu wlan.conf change.
I am now attempting a complete recovery of my Vista system, since it seems irreparably broken. Again coincidence or not?
(For the record, I have already read the other threads. Either they don't work for me or are too difficult.) My laptop is an Acer TravelMate 250. I have installed Ubuntu 10.10 (2.6.35-28 generic i686) after erasing Windows 7. At first, the usb wireless adapter worked. Then, I restarted the PC because of some updates and it didn't work anymore. In "edit connections" I find "Auto SpeedTouch8350DB" which is the wireless connection (on my sis's computer it works). When it tries to connect, I'm asked the password but it doesn't work.
[Code]...
I have a Dell XPS M1330. I installed Fedora 10 on a separate partition and left Vista on the first. It was working just fine and for some reason all of the sudden it is not recognizing the Wireless controller. Vista is still working fine although I did get a couple of "WLAN controller has stopped working" errors. I suspect I may have a physical problem with the controller but I'm confused as to why Vista is still using it but Linux is not. The actual physicall "WIFI" light on the laptop does not even illuminate when I boot Linux. No wireless networks appear in the network list under Linux. Particularly since it WAS working fine for months...
View 4 Replies View RelatedMy PC has a broadcom wlan adapter. When I clean installed Fedora 15 about two weeks back, the wifi wasn't working on its own. I searched the internet and found out that installing broadcom-wl and akmod-wl would solve the problem. I tried it, and the wifi started working after that.
Wifi not working means there is no wireless option in the network settings and the wifi indicator light is off.. when wifi started working both of these got fixed
Now i did a yum update yesterday, after which my wifi has stopped working again. No use of reinstalling broadcom-wl, akmod-wl, or even kmod-wl...
Code:
lsmod
gives
Code:
wl
[Code]....
[URL]
recently ran into a problem with my internet access. Im using open suse 11.2 on a Dell Vostro 1520 laptop. I managed to get my wlan running and i can use firefox to access my router. In my router the laptop is also showing as connnected, dhcp reserved an ip for it.However if i try to browse the internet, no page is loading, actually no software that needs access to the web is working.
View 3 Replies View RelatedI have a Dell Inspiron 1525 laptop using Dell Wireless 1395 WLAN Mini-card (This is what Windows Vista says I have). I have installed Ubuntu as dual boot with existing Windows Vista. Wireless is not working in Ubuntu but working flawlessly in Windows.
Here is the output using CODE: lspci.
hai@ubuntu:~$ lspci
00:00.0 Host bridge: Intel Corporation Mobile PM965/GM965/GL960 Memory Controller Hub (rev 0c)
00:02.0 VGA compatible controller: Intel Corporation Mobile GM965/GL960 Integrated Graphics Controller (rev 0c)
00:02.1 Display controller: Intel Corporation Mobile GM965/GL960 Integrated Graphics Controller (rev 0c)
00:1a.0 USB Controller: Intel Corporation 82801H (ICH8 Family) USB UHCI Controller #4 (rev 02)
00:1a.1 USB Controller: Intel Corporation 82801H (ICH8 Family) USB UHCI Controller #5 (rev 02)
00:1a.7 USB Controller: Intel Corporation 82801H (ICH8 Family) USB2 EHCI Controller #2 (rev 02)
00:1b.0 Audio device: Intel Corporation 82801H (ICH8 Family) HD Audio Controller (rev 02)
00:1c.0 PCI bridge: Intel Corporation 82801H (ICH8 Family) PCI Express Port 1 (rev 02)
00:1c.1 PCI bridge: Intel Corporation 82801H (ICH8 Family) PCI Express Port 2 (rev 02)
00:1c.4 PCI bridge: Intel Corporation 82801H (ICH8 Family) PCI Express Port 5 (rev 02)
00:1d.0 USB Controller: Intel Corporation 82801H (ICH8 Family) USB UHCI Controller #1 (rev 02)
00:1d.1 USB Controller: Intel Corporation 82801H (ICH8 Family) USB UHCI Controller #2 (rev 02)
00:1d.2 USB Controller: Intel Corporation 82801H (ICH8 Family) USB UHCI Controller #3 (rev 02)
00:1d.7 USB Controller: Intel Corporation 82801H (ICH8 Family) USB2 EHCI Controller #1 (rev 02)
00:1e.0 PCI bridge: Intel Corporation 82801 Mobile PCI Bridge (rev f2)
00:1f.0 ISA bridge: Intel Corporation 82801HEM (ICH8M) LPC Interface Controller (rev 02)
00:1f.1 IDE interface: Intel Corporation 82801HBM/HEM (ICH8M/ICH8M-E) IDE Controller (rev 02)
00:1f.2 SATA controller: Intel Corporation 82801HBM/HEM (ICH8M/ICH8M-E) SATA AHCI Controller (rev 02)
00:1f.3 SMBus: Intel Corporation 82801H (ICH8 Family) SMBus Controller (rev 02)
02:09.0 FireWire (IEEE 1394): Ricoh Co Ltd R5C832 IEEE 1394 Controller (rev 05)
02:09.1 SD Host controller: Ricoh Co Ltd R5C822 SD/SDIO/MMC/MS/MSPro Host Adapter (rev 22)
02:09.2 System peripheral: Ricoh Co Ltd R5C592 Memory Stick Bus Host Adapter (rev 12)
02:09.3 System peripheral: Ricoh Co Ltd xD-Picture Card Controller (rev 12)
09:00.0 Ethernet controller: Marvell Technology Group Ltd. 88E8040 PCI-E Fast Ethernet Controller (rev 12)
0b:00.0 Network controller: Broadcom Corporation BCM4312 802.11b/g (rev 01)
hai@ubuntu:~$
I patched my wireless driver in order to support packet injection. Using this tutorial:
- Install the Firmware:
Code:
- Create new directory:
Code:
- Now disconnect Internet and unload all your driver (use rmmod command)
- Move/copy the Compat-Wireless patched in /usr/src/drivers directory and unpack the drivers:
Code:
Blacklist the wl driver: (STA driver)
Code:
Currently I'm running Ubuntu 10.10, Kernel 2.5.35-29-generic. I have a Broadcom 4318 for my WLAN and a Broadcom 4401-B0 for my ethernet. I followed the tutorial and I managed to get packet injection working on my WLAN; however, my ethernet connection isn't working. I tried sudo modeprobe b44, but I get the following message:
FATAL: Error inserting b44 (/lib/modules/2.6.35-29-generic/kernel/drivers/net/b44.ko): Invalid argument
There is no wlan0 interface when trying to run FRITZ!WLAN USB Stick N 2.4 on OpenSuSE 11.2, though it works fine on Fedora 11 and Mandriva Spring 2009.1. All 64bit. Contrary to Fedora and Mandriva, there is no need to compile the compat-wireless module ar9170usb for OpenSuSE 11.2 because the kernel is very recent and includes this driver. Kernel: 2.6.31.5-0.1-desktop The /var/log/messages gives this after I put the stick in the PC. At first it is seen as a mass storage device:
Nov 27 22:00:24 linux-3mwa kernel: [ 73.420755] usb 1-5.1: new high speed USB device using ehci_hcd and address 4
Nov 27 22:00:24 linux-3mwa kernel: [ 73.540834] usb 1-5.1: New USB device found, idVendor=057c, idProduct=84ff
Nov 27 22:00:24 linux-3mwa kernel: [ 73.540841] usb 1-5.1: New USB device strings: Mfr=16, Product=32, SerialNumber=48
Nov 27 22:00:24 linux-3mwa kernel: [ 73.540847] usb 1-5.1: Product: FRITZ!WLAN USB Stick N 2.4
[Code]....
i'm trying to get my WLan working, i do have a Broadcom BCM4312 lpphy WLan-Adapter (pci-id according to lspci -vnn is 14e4:4315) in my Lenove ideapad S12. My System is Debian Lenny, but in order for the WLan-Adapter to work I installed the 2.6.32-3-686 Kernel from debian squeeze (using apt-pinning). I than installed the b43-firmware as described in the debian wiki [URL]. I updated the init-ramfs, everything is working as expected, except for WLan.
It shows up using iwconfig, i can get it up and down using ifconfig (or ifup, ifdown). I can't do a scan using iwlist - it says: % iwlist wlan0 scan > Failed to read scan data : Resource temporarily unavailable
It always fails, but not with the same error message. Sometimes it also comes up with > device or resource busy
Using dmesg I see reports about a fatal DMA error, resulting in a controller RESET. It says it's loading firmware 478.104 .
I have an HP Pavilion notebook with a Broadcom WLANcard that had been working very nicely in Fedora Core 10 until this evening, when I took my notebook to a conference room where there was no internet access. (I tried to connect to wireless networks, but there were none in the area, as I discovered.) am now unable to connect to my local (home) wireless network as the device is now non-existent . Can someone please walk me through the steps to fix this or re-install it (I have tried reinstalling broadcom-wl, but that didn't help). My lspci listing is reproduced below:
Code:
00:00.0 Host bridge: Intel Corporation Mobile 945GM/PM/GMS, 943/940GML and 945GT Express Memory Controller Hub (rev 03)
[code]...
I have searched around a bit for a knetwork manager issue I am having on my opensuse 11.2 32 bit install. My wireless card is an 04:00.0 Network controller: Broadcom Corporation BCM4312 802.11b/g (rev 01) I am currently using the Broadcom wl driver
I am on the Internet with this machine as I am typing using the older "ifup" method. I am having great difficulty connecting to the Internet when I use knetwork manger though. The strange part is when I am connected to my router with knetwork manager, I can log into my Router, but I can not get to any web-page/ping any outside address.
so far the best (I was able to locate) advice I was able to get is located in this post. < Broadcom wireless, partchy internet - openSUSE Forums > following a posted how to to disable IPV6 (I suspect this may be the issue??), I was unable to locate modprobe.conf, or modprobe.conf.local, even after I updated via updatdb. I gave a shot at entering in "disable_ipv6=1" into "menu.lst". However, this did not solve my issue with knetwork manager. If my network information is needed when I am "connected" utilizing knetwork manager
I have just installed openSuse 11.4 KDE 64-bit on a Dell M1330. When I click on my networking panel, it says WLAN interface is unavailable. I've followed the steps in the stickied post and found the WLAN hardware info, a screenshot of which is below:Uploaded with ImageShack.usNext it says to do this - you need to look at the logs, in particular the info in /var/log/boot.msg. To see this, you need YaST => Miscellaneous => System Logs and select boot.msg.In YaST there is no such option for system logs under miscellaneous, so I can't do that. The results of the sudo /usr/sbin/iwlist scan command produce the following:
root's password:
lo Interface doesn't support scanning.
eth0 Interface doesn't support scanning.
[code]....
/var/lib/NetworkManager/NetworkManager.state
everything is true.
i have a HP G60441US with the circular wifi button and i can enable it in windows and ubuntu 10.04 but in 10.10 wifi will not work.
For the past almost year, once in a while my wifi won't work.At home,I use an ethernet cable. When I go out, or am out of town, about 1/3 times the wifi won't connect, and won't even find access points. Once this happens, no matter how many times I restart, the wifi won't work. The ONLY way I can get it to work again is if I reboot with the ethernet cord plugged into the laptop and into a router/switch/hub. My neighbor (the one who got me into Ubuntu) is a pretty experienced linux network admin who looked a my laptop and has no idea what is causing this. I've attached my syslog log entry for the last time this happened. Does anyone know why this is? I LOVE ubuntu but I may need to switch back to Windows because I NEED wifi to work.You will see in the logfile I tried connecting to two different APs. The one that always works is the second one, called linksys.
Syslog:
---------------------
Apr 19 12:04:07 ubuntu NetworkManager: <info> Activation (wlan0) starting connection 'Auto sammysosa'
Apr 19 12:04:07 ubuntu NetworkManager: <info> (wlan0): device state change: 3 -> 4 (reason 0)
Apr 19 12:04:07 ubuntu NetworkManager: <info> Activation (wlan0) Stage 1 of 5 (Device Prepare) scheduled...
Apr 19 12:04:07 ubuntu NetworkManager: <info> Activation (wlan0) Stage 1 of 5 (Device Prepare) started...
WiFi worked PERFECT in 9.10 after
Code:
Sudo apt-get update
apt-get upgrade
But that only worked when I put in my eth0 cable to get the Updates. Now I upgraded to 10.04 LTS and it isn't working- eth0/wifi. So Now what do I do if i can't even get the updates in Terminal?
i have Dell 1535. I installed Kubuntu 11.04 on it, now wifi is not working at all. Here is the output of some command i saw already in previous post related to this problem.
Code:
~# lspci | grep Network
0c:00.0 Network controller: Broadcom Corporation BCM4312 802.11b/g LP-PHY (rev 01)
~# ifconfig
eth0 Link encap:Ethernet HWaddr 00:21:70:70:c2:91
UP BROADCAST MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
[Code].....