My Ubuntu Linux system was switched off at the mains without being properly shut down. When it was restarted again, the file system checks failed and I was presented with the maintenance console command prompt. How do I check what is wrong with the file system. Is there any sort of generic repair command that checks the disk and fixes errors?
View 1 Replies
I'm used to having my computer do a fsck every 30 boots or so...Fedora doesn't seem to do that...am I missing something?
View 5 Replies View RelatedI have 10.04 with Gnome installed and can change filesystem checks using tune2fs from the command line.
How to create a script for tune2fs and add to the Gnome System menu?
How to diasable filesystem checks on boot?
View 9 Replies View RelatedI'd like to keep root pw==sudo pw==user pw on a box with Code: $ lsb_release -ds Ubuntu 9.10 $ uname -rv 2.6.31-22-generic #61-Ubuntu SMP Wed Jul 28 02:02:56 UTC 2010 Just now it hung going to sleep, so I shutdown via BRS. On cold boot, HD mount failed and I got the prompt to hit Esc to goto maintenance shell. I did that, got the prompt for the root password, and entered my sudo.
That failed! though it has worked before ... but I changed my user password on that box recently, and I'm pretty sure I haven't needed to fsck between then and now. I'm wondering: What do I need to do to set my root pw? I was able to C-d out of the shell, and karmic took care of itself, but I'd prefer not to rely on that. Is there a way to make my root pw always equal my user pw? If so, is that a Very Bad Idea?
On a Sun Ultra10 333MHz, 512M, 9gB HDD. Booting Fedora-9. Silo v1.4.14 into kernel 2.6.27 64bit (vmlinuz-2.6.27.12-78.2.9fc9.sparc64). This is a brand-new installation.Although it's running on a Sparc it makes v.litte difference so far as this bootprocess, teh way Linux runs, where everything is - is concerned. That's why I've cross posted this query here.Booting merrily, in the interactive startup section just past "Starting udev", "Setting hostname", at "Checking filesystems" I get:
/: clean, 155284/557056 files, 920932/2225412 blocks
fsck.ext2: Device or resource busy while trying to open /dev/sda
Filesystem mounted or opened exclusively by another program? [FAILED]
*** An error occured during the filesystem check
*** Dropping you to a shell, the system will reboot
*** when you leave the shell
*** Warning --SELinux is active
I notice when Linux boots in maintenance mode the filesystem is read-only.
Is there a way to change this, perhaps remounting as writable?
An example of this being a problem is that I was unable to open vi because there were too many session files....
Not to mention it would be nice to actually fix problems....
What are you meant to be able to do if you can't make any changes to the filesystem? What kind of maintenance can be expected?
I'm running Ubuntu 9.10 on a dell desktop from idk when, its fairly old but regardless it was all running fine until about a week ago I got the infamous:
Mount of filesystem failed. A maintenance shell will now be started. Control-D will terminate this shell and start a new one. admin@ or whatever it is you get the point.
I've been trying all the possible solutions I could find and nothing seems to work. I just want to be able to use this computer. I don't care if I lose files, or have to re-install Ubuntu or any of that, if I can just get the thing running again. I've tried re-installing, and booting from the disc etc. none of which have worked. Basically, I just want to erase Ubuntu and re-install it.
I have a dual booting newly installed 64 bit Ubuntu 9.10 on my machine. It was all fine until today. Now when I boot into Ubuntu, I see the error Failed to mount root filesystem. I cant remember any significant changes during the last session. One thing I remember is I upgraded the system using the update manager which asked me to choose an option for grub boot loader. I opted for its upgradation. After the upgrade, I was able to work with Ubuntu for a few more sessions. Windows XP works very fine.I checked other threads which suggested running fsck, but it did not help. fsck does not report any errors.
View 1 Replies View RelatedMount of file system failed.this is the message i get wen try to boot into ubuntu 9.10 i dont knw how to rectify it
View 2 Replies View RelatedI have a 64 bit Karmic system with two drives. One is mounted as / and the other is mounted as /home. I just put the video card from my system into my son's system and got a new video card. (Don't see how it's related but still...)Now I am getting the following message when I turn on the system. code...
View 1 Replies View RelatedI am installing Ubuntu 9.10 on my computer and I get the following error:
"the ext4 file system creation partition #2 of Serial ATA RAID nvidia_bjfefgci () failed"
I followed the following instructions to prepare partitions [URL] and allocated 10,000 MB for swap, 245,000 MB for the one with / mount point and 245,000 MB for the one with /home mount point. I have two 250GB HDDs.
I was using 9.04 for a while because it was working for me, I decided to upgrade yesterday using the Upgrade button on synaptic to 9.10. Now when I boot I get an error message:
Code:
chroot: cannot execute /etc/apparmor/initramfs: No such file or directory
Mount of filesystem failed.
A maintenance shell will now be started.
CONTROL-D will terminate this shell and re-try
I want to try to fix the problem so I do not have to do fresh installation.
I have got arch Linux dual booting with Win XP on my laptop. I have been getting a filesystem check error since yesterday and am unable to start Arch. Upon googling and searching the arch fora, I came upon some advice which I tried which has not worked yet. Hence the new post.Basically, I was attempting to print something off and accidentally chose a printer that was not connected to my laptop. After half a minute or so, it repeatedly started giving me notifications that the printer was not connected...in excess of 200 messages that the printer was not working which continued to pop up despite me canceling the print job. The whole system got really sluggish (for the first time in the last year) and I had to restart the laptop upon which the boot messages appear. It gets to the point where its loading the various filesystems. It mounts root and says it fine.
I tried fsck which tells me that home and boot are still mounted.So I booted up using an Ubuntu Live CD and checked and repaired each file system which it successfully did. Upon rebooting into Arch, I am getting the same message.I have not installed anything new and had upgraded the whole system a few days before the problem started.
After upgrading and restarting my laptop, The purple splash screen hangs, and the terminal gives this message.
Code:
Also the boot menu does not show (I cannot open the recovery mode)
I've just got a new laptop with 4GB RAM available, in order to fully utilize the available memory I'm going to install Ubuntu Lucid Lynx 64bit, but when I boot with Live CD, I always get the following errors:
Code:
BusyBox v1.13.3 (Ubuntu 1:1.13.3-1ubuntu11) built-in shell (ash)
Enter 'help' for a list of built-in commands.
(initramfs) mount: mounting /dev/loop0 on //filesystem.squashfs failed: Input/output error
Can not mount /dev/loop0 (/cdrom/casper/filesystem.squashfs) on //filesystem.squashfs
Crashed System left at root @ maintenance shell. Below is the sequence after boot, with Exact Errors. How to Salvage important files from my crashed laptop hardware.
A) Via a Transfer to a USB stick in Terminal, would be ok
B) Via SSH through the router from the good laptop that is Preferably using Nautilus / GUI, Terminal also ok (less confident of my skill here)
C) Directly Fixing Laptop and being ably to use Nautilus / GUI to Copy Files to USB stick, localy
The result of some effort:
A) the USB stick is good but Can't get in to it from the crashed laptop
B) SSH: No luck I get: "Cannot display location "sftp://192.168.1.101/"" from the good Machine
C) at a lose here...
The Crashed Laptop is:
Ubuntu: 9.10
Linux: 2.6.31-22-generic
Gnome: 2.28.1
CPU: Intel Atom N280 @ 2GHz
NO: CD / DVD Drive
(USB Boot maybe possible? Have not made a Bootable Ubuntu USB Yet)
BOOT:
GNU GRUB Version 1.97~
Ubuntu, Linux 2.6.31-22-generic
etc / (& recovery mode)
Mini Ubuntu logo or splash screen
File-system checks are in progress sticks every time at 4%
init: mountall main process (418) terminated with status 3
#(it seem to count up every time I re try to boot ? (init: mountall main process (423)(429)(etc)
Mount of filesystem Failed.
A maintenance shell will now be started.
CONTROL-D will terminate this shell and re-try
root@Bi-Ji-Ben:~#
I can navigate around but cant get the GUI up
root@Bi-Ji-Ben:~# nautilus
could not Parse arguments: Cannot open display:
A good USB stick reads & writes in another laptop running Ubuntu 9.10. When I connect the USB to the Crashed Machine it starts with:
"assuming drive cashe: write through", and hangs on this tell I press: "Ctrl+C"
In the crashed machine I can't seem to get into the USB anywhere that I think it should show up and trying to "mkdri" got me:
"Read only file system".
And now i have lost more than 1.9 TB of data.
Ok, i know. there should have been a backup. I came that far... but not beyond. I have bought a STORA MS2000 and 2 x 2TB WD EARS Harddisk. Except a couple of troubles that i had to go through with it - it finally worked. It did for 3 months. I have moved the NAS from one room to another and when i reattached it ... i all of a sudden didnt work anymore.
Tick, tick ... tick ... just like it would have a head-crash. I attached the disks to my iMac just to know what they sound there. Of course the iMac couldnt reat the disks. The disk-utility just let me know that the file-system is XFS (so far i knew) .. and then they are striped. So i knew i wouldnt be able to retrieve my data there ..
My question now. Since i dont think that my harddisks have a serious damage - how in on Gods Earth could i save my data from an XFS striped volume that was taken out of a STORA MS 2000?
I hope i wont loose all my data now ... but dont know if i would have any success to setup a Linux-PC and then have to look for the right software or even buy a card or so ...
A friend of mine upgraded his pc to ubuntu 10.04. Sadly enough we ran into issues with his graphics card, which apparently doesnt work well with lucid. We decided to downgrade to 9.10. I did this by installing over the old partition and chose to import the settings from the old account.The problems started when the pc booted for the first time:The list of kernels in grub2 was the one from 10.04.Somehow grub2 from the old installation seems to be still around and messes everything up. Any ideas how I could fix this?
View 6 Replies View RelatedI upgraded 9.10 to 10.04 via the web. The program announced it would take several hours, and when I came back to check, computer was off (kids?). Anyway, machine boots and 10.04 starts, but then blinks a few times and goes to a prompt. What should I tell it?
I have a 10.04 disc too, but it won't run from that either (Cannot mount dev/loop0 on filesystem.squashfs failed). Same message when I tried to start a nearby Windows machine with it. Disc "verified" when I made it. What's with that?
I decided to try to do the 3 distro upgrade stretch from 8.04 to 10.04 this weekend and now I am hung on 9.04 to 9.10.. The upgrade went swimmingly, but I hit a wall upon boot. When I try to load kernel 2.6.31-22 I am greeted with the following error:
Code:
[ 20.879845] ACPI: I/O resource vt596_smbus [0x400-0$407] conflicts with ACPI region SMOV [0x400-0x406]
Mount of root filesystem failed.
A maintenance shell will now be started ... After doing some digging I found this thread which appears to be similar in the inability to mount the filesystem. However, it does not mention the ACPI error. I tried everything in that thread; verifying device ID's, editing fstab options; running a filesystem check, and flipping the UTC option in the rcS file but nothing worked. The OP of that thread eventually did a fresh install of Karmic; but I would rather not have to go that far.
This is a Natty system. I ran update manager to update to the latest releases for Natty, and it crashed. I ran it again and it told me it could only do a partial upgrade, and that I should do apt-get install -f. I did that, but apt-get told me the system was locked by another program. Not to worry I thought, I'll just reboot. So I did that, and I think Update-Manager got a lot further through the process than I thought, because my system is borked. It'll boot into Gnome, but when booting up the Boot Screen no longer shows the pretty Ubuntu Logo, but rather a line of text that says "Ubuntu 11.04".
When it gets into Gnome the keyboard and mouse more or less don't work (although the keyboard based Fn+9 and Fn+10 brightness control still works) and there is no desktop background. After about 30 seconds something crashes but I can't click on it to find out what. Going into the recovery console doesn't help either. The latest Kernel (2.6.38-7) stops moving forwards after "Begin:Running /scripts/init-bottom...done". has occurred for the second time. Luckily I still have the previous kernel, which gets to the same spot and then tells me:
"init: udevtrigger main process (390) terminated with status 1" and then "init: udevtrigger post-stop process (394) terminated with status 1".
I then get the message
"The disc drive for / is not ready yet or not present. Continue to wait; or Press S to skip mounting or M for manual recovery". S goes back to "Begin:Running /scripts/init-bottom...done" a second time, M brings up the message:
"Root filesystem check failed. A maintenance shell will now be started"
and then it asks for the root password and gives me a terminal. Everything seems to be there, but apt-get and dpkg both can't do anything as the filesystem is read only.
Running F12 on my compaq evo N410c. Did a system restart 4rm gnome logged in as root & now grub cant mount my root filesystem, it boots vista though. How do i rectify dis.
View 2 Replies View Relatedi want to use linux but i am having some issues getting it to work on my system. my desktop is a p4 3.4gig with 512 DDR. When I insert my ubuntu CD it starts loading but then i get this screen/message:
Busybox v1.15.3(ubuntu 1:1.15.3-1ubuntu5) built-in shell(ash) Enter 'help' for list of built in commands (initramfs) mount:mounting/dev/loop0 on// filesystem.squashfs failed input/output error Can not mount /dev/loop0 (/cdrom/casper/filesystem/squashfs) on //filesystem.squashfs if I put the same disc into my HP laptop it boots up ubuntu fine. (however it won't allow me to get online, but that is a different issue).
My Fedora 12 System was failed when booting.The message like that : mount: wrong fs type, bad option, bad superblock on /dev/mapper/my_vol missing codepage or helper program, or other error. In some case, useful info is found in syslog - try dmesg | tail or so Can't mount at root filesystem. [drm: drm_mode_rmfb ] *ERROR* tried to remove a fb that we didn't own. Boot has failed, sleep forever. I guess something wrong with my hard disk, so the bootloader can't recognize the filesystem type.
View 2 Replies View RelatedI have download file from this site and have done these steps [URL].
tar -xvf ntfsprogs-2.0.0.tar.gz
chown root.root -R ntfsprogs-2.0.0
cd ntfsprogs-2.0.0
./configure
make && make install
Still I have failed to mount ntfs partition with this command..
mount -t ntfs /dev/hda1 /mnt
or
ntfs-3g /dev/hda1 /mnt
The error is .................
mount: unknown filesystem type 'ntfs'
I am using RHEL5.4 and kernel is 2.6.18-164.el5
When I try to mount a linux file system that was encrypted using cryptsetup I get the following error:
debian:/# mount /dev/sdb3
Command sukey slot 0
mount: u moet een bestandssysteemsoort aangeven
mount failed with run_sync status 32
Command failed: Device busy
mount.crypto_LUKS(crypto-dmc.c:168): Could not unload dm-crypt device "/dev/mapper/_dev_sdb3", cryptsetup returned HXproc status 240
"mount: u moet een bestandssysteemsoort aangeven" is dutch for
"you must specify filesystem type"
I had a LiveUSB of CentOS 5.5, so I decided the install it.With no installer,I just copied the files to my hard drive.his was in a multi boot with Windows 7, Ubuntu 9.10, and FreeDOS.I updated GRUB2 and it detected CentOS. I loaded my entry and it failed to mount the root filesystem.I took the initrd0 file from the LiveUSB syslinux folder and added that ramdisk to the entry. Now it finds the root filesystem (/dev/sda9 as Ext3).But it fails shortly after loading /sbin/init. It talks about an init error where it says "File not found!!!".The previous lines involved umounting old filesystems, like /dev.
View 4 Replies View Relatedit's my first day of trying to figure out Linux, and I now understand why it's been largely used by the geek community.I've tried to install both xcdroast and 7zip using the console and failed miserably both times.7zip doesn't have a ./configure and xcdroast just gives me errors that I don't understandI think I need a package manager?
View 6 Replies View RelatedSo i insert the ubuntu 10.10 in the dvd and boot it. The menu comes up and i choose to install ubuntu. After that it shows some black screens and this error:
(initramfs)mount:mounting/dev/loop0 on//filesystem.squashfs failed: Input/output error cannot mount /dev/loop0(/cdrom/casper/filesystem.squashfs)on//filesystem.squashfs
The disc aint scratched. I tried installing from Windows but i got another error.
And for some odd reason Ic ant make a removable startup disk:
