Ubuntu :: Screen Goes Blank Or Boots To Tty1 After Loading Screen?
Apr 15, 2011
like any other Linux newb, I came to Ubuntu because my Windows crashed one time too many. And I chose Ubuntu because "it just works". But these past few days that hasn't been true. I'm posting this from a netbook with Ubuntu, and am having no problems whatsoever, but normally I use an Acer Aspire 5920G laptop. I'll include the specs as written on the sticker:
* Intel Core 2 Duo processor T5250 (1.5GHz etc)
* Up to 1024 MB Nvidia Geforce 8600M GS Turbocache
* 2 GB DDR2
Let me know if you need more details, and I'll add them later. Now, what happened was I clicked "hibernate" while leaving Firefox open. (I've done this hundreds of times, no problem) And when I went to turn it back on the next day there were weird graphical glitches in the loading screen, and it booted to the "tty1" prompt screen. I did a lot of googling and found quite a few posts about it, but the solutions either didn't work, or I didn't understand them. After trying several different suggestions from this forum and others, I managed to delete the graphics drivers. That enabled me to boot in low graphics mode, and naturally, I tried a whole bunch of things to make it work properly again. That only made it worse. Now it went straight from the loading screen to just blanking out and turning the display off. So, I tried new things. Over and over. The weird thing is even when I disconnected my harddrive and ran from a Live USB, the problem persisted. Could there be an issue with the graphics card itself? Anyway, after reconnecting the harddrive I tried to boot again. And it suddenly worked. Even HDMI to my bigger screen worked.
[Code]...
View 1 Replies
ADVERTISEMENT
Dec 26, 2010
Is there a known problem with the Lubuntu 10.10 image here? I have downloaded it to two different computers, then burned the images to two different blank CD's (different brands) and neither loads. Both only get as far as the Lubuntu menu, once ENTER is pressed at that point to load the LiveCD, a blank screen eventually appears with a flashing cursor at the upper left of the screen, that's it. They were both burned using the slowest burn speeds available.
View 9 Replies
View Related
Mar 1, 2011
Something plagues my Ubuntu box since I upgraded to Ubuntu 10.10 - I end up with a blank screen while booting. I use an Asus F81SE Notebook, and Dual Boot with Windows XP. Everything worked fine with Ubuntu 10.04.
When I start my notebook after the upgrade to Ubuntu 10.10, I come to Grub, and when I select the latest kernel available, the hard disk LED blinks for a second, turns off ... and nothing happens any more. There is just a blinking text cursor.
As I upgraded from the previous Ubuntu version, there was an older kernel left (2.6.32-26-generic), which boots up fine.
I run 64 Bit on an Intel T4200 CPU. Booting the Live CD brings me to the purple screen with the open source logo at the bottom. I tried 32 Bit and 64 Bit versions of Ubuntu 10.10.
I don't seem to find similar problems on this forum. But does anyone know how to find the mistake?
View 9 Replies
View Related
Apr 10, 2011
I installed Lucid Lynx to a Gateway Solo Pro 9300(600 Mhz/224 M) and everything looked normal on the display with cursor,icons and abatross background. I rebooted and I have a blank screen with only a cursor showing. I don't think it is a video card problem because I had a normal display upon installation. Is there a way, on boot, to get into a diagnostic mode? what should I look for in the diagnostic mode?
View 4 Replies
View Related
Feb 9, 2010
php pavilion ze4900 was workign perfectly then i installed some navidia driver thing ( wich wasnt for my cp) and then when i restarted it went blank.
View 7 Replies
View Related
Apr 8, 2010
I've had no problems out of my multi-boot setup.. at all, and now all of a sudden (after an update on ubuntu? my JoliCloud and Ubuntu seem to do the same thing.. they show the logo then go to a black screen, doing nothing afterwards. i was wanting to know how to get this working again.. this is an Acer aspire One 11.6in AO751h. it's using grub to boot into it. i used EasyBCD to get it to let me choose ubuntu from windows start menu and it takes me to grub and all works(well worked until some update?) well.. even my windows 7 boots up just fine...
View 1 Replies
View Related
Apr 25, 2010
I am a complete Linux newbie and I tried installing the latest release candidate (10.04) as a dual boot with Windows XP. The install seemed to go fine and it said it needed to reboot to finish the install. It rebooted and then displayed a series of errors on a DOS-like screen (which I wish I wrote down). When I realized that it was definitely hung, I then held the power button to shut it off. After that, all it does is boot to up to a blank/black screen with a cursor.The box is old and I was actually going to throw it away, but I figured this was a good opportunity to give Linux a try. At this point, I'm willing to go to either Windows or Ubuntu... I don't really care which. I actually just want to recover some files on the box
View 7 Replies
View Related
Jun 23, 2010
I'm using Ubuntu 10.04 64-bit, which is installed to a second hard drive on my desktop. Earlier this afternoon, there were two 10 second power outages in my neighborhood. The first caused the system to restart with no effect, but after the second outage Ubuntu no longer boots properly. The problem is this: When I boot, I get to the grub screen. I have tried choosing four different options (the most recent kernel, a slightly older kernel, and the recovery mode of each). For each, kernel begins loading, but at a certain point the input to the monitor dries up, and after a few seconds the monitor enters standby mode. When I boot into recovery mood, the last message I see before the screen goes blank includes "udev starting version 151" followed by three lines that read "assuming [something that I can't read before the screen goes blank]." The computer itself remains on, but I have no way of knowing exactly what it is doing.
There seems to be no hardware damage as I can boat into Vista, and I can also boot into 10.04 from a USB. I've used fsck to check the partitions on my hard drive and the test came up clean for all of them. Since I only installed 10.04 a week ago, I could just copy the handful of useful files I have to my external drive and re-install, but I'd like to get some experience troubleshooting this problem. My first assumption is some kind of problem with the video drivers or GUI.
View 2 Replies
View Related
Feb 5, 2010
I might want to try and put a gui on my ubuntu server installation went fine however now I'm staring at a blank screen. ubuntu boots goes to screen similar to desktop (loading with the mouse cursor) and then blank... occationaly it'll load a partial username box but more offten than not it loads a completly blank screen and the caps lock and scroll lock lights on the keyboard are both blinking consistantly...
View 1 Replies
View Related
Mar 28, 2011
I recently did an upgrade over the internet from the previous version 10.04. After everything required was downloaded and installed, I rebooted. Now, the system only displays a blank screen after a quick flash of "Ubuntu 10.10".
I have a copy of the 64-bit Desktop install CD of 10.10. I tried to boot up live with it. Same problem.
My system:
K8M800 motherboard
AMD Sempron 2600+
1 Gig RAM
Integrated graphics: VIA S3 UniChrome Pro
View 6 Replies
View Related
Jul 23, 2010
My laptop will be fine, then it turns off then immediately boots itself to a blank screen and no hard drive activity. This has happened 3 times today and never before. what ive done so far The first time this happened i tried turning it off and back on, still no screen and no hard drive activity so i took one of the RAM sticks out. Booted fine... To confirm that the RAM was bad i put it back and tried booting again, unfortunately it booted fine... i thought it was a fluke.
Until his happened a second time and instead of taking the RAM out, i waited a half hour and rebooted and it started booting fine, i turned my back for a sec and it was dead again. I have taken that RAM module out and am hoping it will not happen again, but it could well be the other RAM module since i really don't know or even if it is RAM at all.
Question is. Is this a RAM issue or something else? Where can i find a log to see what happened immediately prior to it offing itself? What's the chances it's the heatsync? (the laptop doesn't feel as hot as it sometimes does)
View 8 Replies
View Related
Aug 16, 2010
My next door neighbor has a dell Optiplex gx270 and wanted Ubuntu installing.
Hardware:
1gb RAM
P4 2.4
Intel 82865g Onboard Graphics.
40gb HDD
I tried the live cd and it froze on bootup, so I thought it might not be enough ram as the case sticker said 512mb ram. So I booted the minimum install cd and installed ubuntu desktop on it and then rebooted, when it boots i get grub and then screen will either do 1 of 2 things.
1. I get another flashing cursor in top left corner and then cursor stops flashing and then nothing happens at all.
2. Then screen will go black and nothing will show at all.
I have tried updating the BIOS, adding i915.modeset=0 to grub, didn't work either. Also couldn't find the xorg.conf under /etc/X11 to change driver to vesa. After several reboots atleast 30 since the check disk think showed and then it froze again. it booted correctly so I tried the latest intel driver from xorg edgers ppa. Rebooted and still the same thing happens. tried 2 different installs now and get same results. I have had to put winxp on it so he can atleast use it, but this will run out in 30 days unless he decides to buy it.
View 6 Replies
View Related
Aug 25, 2011
I've posted this to the fedora mailing list with no response, my apologies if it's been addressed here...
I have an IBM Thinkpad with an Nvidia card ( nVidia Corporation GT218 [NVS 3100M] (rev a2) )
I currently have the nouveau driver black listed in my grub.conf setup: rhgb quiet nouveau.modeset=0 rdblacklist=nouveau
I did the update which installed/updated the following:
---> Package kernel.i686 0:2.6.35.14-95.fc14 set to be installed
---> Package kernel-devel.i686 0:2.6.35.14-95.fc14 set to be installed
---> Package kernel-headers.i686 0:2.6.35.14-95.fc14 set to be updated
---> Package kmod-nvidia.i686 1:280.13-2.fc14 set to be updated
However when I reboot the system boots to a blank screen, and even the previous kernel boots to a blank screen. I tried installing akmod-nvidia but get the same results
I've restored the system back to before the update for now..
View 1 Replies
View Related
May 12, 2010
I can't seem to get Ubuntu to run on my old Dell Dimension 2300. It boots to a purple screen then it goes to a black screen with a load of writing nothing else happens after this screen. [URL] Could someone advise how I can get it to work?
View 1 Replies
View Related
Jun 15, 2011
I've just done a clean install of 11.4 from a Net install CD. I left it unattended while it installed, and came back to find a blank screen with just an xterm. I've rebooted it, and tried both the normal and the failsafe modes, but I just get the same result. The terminal contains the following:
[code]...
View 6 Replies
View Related
Jan 22, 2010
I am new to ubuntu and I would really like to try it out, however I cant do the demo it freezes, I cant boot it either. I got rid of the quiet splash and watched it load. The last thing I saw before it went to just a blank screen was the ubuntu logo and it said loading apparmor then ok, went back to the previous command line screen and said done. Then it was just blank. No mouse, no blinking cursor, nothing.
View 2 Replies
View Related
Jun 30, 2010
I'm attempting to install Ubuntu Netbook remix (however I have tried others) on a 32 bit laptop but after it goes through that ubuntu loading thing, it goes blank after that and I've determined that it's not the cd and it's something to do with the hardware after looking at other posts with similar issues. I do not have an operating system on this laptop.
View 3 Replies
View Related
Sep 5, 2010
ive downloaded the Ubuntu CD from the official website and burned it twice, once one a dvd and the other on a normal 700MB CD-RW.in both, the screen went blank after the loading part before the main menu (installation, try it blah blah..)what should i do?btw i use a windows XP and here is my hardware details...sapphire hd 5770 1gb, 4 gb of ram,Intel Core i5- P55 .5 ghz, i think that its enough for the minimum of the ubuntu isnt it?
View 4 Replies
View Related
Jan 21, 2011
Try to load my system today and nothing come up, only the terminal window. Whatever I type in is working, like now I type in the terminal firefox and it is how I ended up here. Try to type thunderbird in the terminal and my mail server started no problem. But nothing on my screen, don't no where to go from here.
View 9 Replies
View Related
May 14, 2010
i have installed ubuntu 10.4 on my compaq 615 system successfully but when i restart the system it freezes, jus giving me a blank screen... i already have windows 7 home premium on the system then i partitioned sum space for the ubuntu but it still dosent work...
View 4 Replies
View Related
May 9, 2010
I am having the same problem, as soon as X tries to load my screen just goes blank. I have an ATI Radeon 9550. At first I tried switching between VGA and DVI as well but upon ruling that out, I switch to my on-board video card and that is working thus far, but I'm trying very hard to figure out a way to be able to switch back. Anyways I'll check back in later on if I have any new information I will post.
View 3 Replies
View Related
Apr 25, 2011
I got a new Lenovo S20 and I am having trouble loading Linux. I've loaded these variants with no success:
Ubuntu desktop
Ubuntu server
Linux Mint
CentOS
vmWare esxi
The live CD's run, and very nicely at that. But once I install to the workstation they won't boot. I just get a blank screen. I've tried different bootloaders.. I've toyed with different BIOS settings.. I've even installed to different drives (a hard disk and an SSD). Maybe a hint: BSD installs and runs with no problem at all. I have PC-BSD running at the moment. It's nice, maybe I'll keep it. But I'd rather have Linux.
My amateur computer science mind sees this as not a boot loader issue (recovery mode shows Linux seems to be loading to a point.. but I can't see the script line just before the lockup) not graphics related; UB Server and vmWare are text-only and they won't load either probably not a bios issue (liveCDs run and other people run Linux on S20s) not hardware (Windows and BSD run on this one)
View 1 Replies
View Related
Jan 1, 2011
I've made a Live CD of version 10.04 on a machine running 10.04 (amd64). The disk boots fine on a 2nd machine but does not boot on the machine that created it. The CD/DVD is new and works for other things so I don't think it is this. The Live CD gets to the ISOLINUX screen but instead of "Loading" the screen goes blank and the system shuts down. I've tried everything I can think of (the disk works fine on another machine).
View 3 Replies
View Related
Apr 9, 2009
I'm trying to build a dual boot ubuntu 8.10 and fedora 10.I have ubuntu sucessfully installed. with a free partition ready for fedora.I cant seem to get fedora past the beginning of the install. Once it says its loading anaconda, my screen either goes blank, or the anaconda fails and the install exits, telling me to reboot my system.I have downloaded the DVD twice. once from the website, and i think when I bruned it it didn't burn right, I then downloaded it from torrent just to be safe and reburned at the slowest speed. It passes the media test.
I have been reading around it may be cause of my video card?My computer is the following.AMD Athlon +2400 XPXFX Nvidia Geforce 6800 GT or something close.80 gig hard drive1.5 gigs of DDR ram.MSI Motherboard not sure of model off top of my head.I really wanna get this dual boot working, As I feel fedora may have advantages over ubuntu. I was going to try to get ahold of another video card, and maybe try that. What do you think I should do
View 14 Replies
View Related
Oct 25, 2010
I have been using ubuntu wel a long time now and I know my way around in linux but I recently updated my laptop from ubuntu 10.04 to ubuntu 10.10 all went fine until I had to restart my laptop. I got a purple screen (loading screen) with 4 dots and a oldskool like font which said: Ubuntu 10.10 Right after that the screen goes purple and its like the system halts I hear no login sound etc just a purple screen. So I did a clean install from the 10.10 live cd which booted perfectly fine and the system was also useable like before. But when I installed the system and rebooted it again no problems.
But when I tried to install the proprietary nvidia driver (the recommended one) I got the same problem again the purple screen. After searching a while on the internet I only found posts which had the problem with ATI cards but my laptop is fitted with a Nvidia Geforce 9300 M card. So I tried several things like removing the xorg.conf (read it somewhere) which ofcourse did not work, and booting in graphics fail safe mode which worked. So the point is in 10.04 and 9.10 I CAN use my video card drivers but not in 10.10 is there a solution to this problem? I am talking about the 32 bit version of ubuntu and here's my system hardware profile:
Intel core 2 duo t7350 @ 2,0 ghz / 3mb l2 cache
2 GB DDR3 ram
160 gb hdd
Nvidia 9300m gs
Chipset: I dont know sorry
Model: Samsung R710
View 2 Replies
View Related
Jan 26, 2011
The day started as usual until I got the very bright idea to install Ubuntu. A new OS along side W7, that sounded great. I checked some guides on the Internet, it was all very straight forward. Install it and Grub will show you the OS:es when you boot up. I installed Ubuntu, rebooted. After the BIOS messages the screen goes blank and my screen on-button begins to blink, as if trying to find a signal, I press enter, it reboots instantly. After BIOS messages I get to a screen that says "GRUB error: uknown filesystem grub rescue>"
I've looked through everything here and nothing works. I've tried to fix the mbr-thingy using Windows Repair and even though it says "one partition was updated with new boot-thingy" when I reboot, I get into that very same grub rescue. I think my setup has something to do with it. I run RAID0 (2x360Gb hard drives), first having C: at 50Gb and then the rest as F: for programs and such. What I did was that I shrunk the F: part and then used that as partition for Ubuntu. Also please have a look at these screenshots, my partitiontables and such seems completely wacky to the raid: Where should the boot-loader go? I'm very, very new at this. I've had Ubuntu Netbook remix on my netbook for a time but still treat me as an utter beginner.
View 4 Replies
View Related
Oct 9, 2010
I'm trying to test out using xubuntu 10.04 on my one computer and keep getting a black/blank screen after selecting the 'try' menu option.Is there a way to fix this?I have tried some of settings via F6 with no luck.
FYI -The CD works fine as I have tested it on other machines.The version I am trying is xubuntu x86 (although I have tried ubuntu 10.04 x86 with similar results).I can Alt+Ctrl+F1 fine and get to the cmd prompt
View 1 Replies
View Related
Jan 14, 2011
I fixed this issue on 10.04, but just recently (1 hour ago) upgraded to 10.10 and am having the same issue. Machine boots fine, but the screen is blank for most of the boot, and plymouth is up for about a half second before I get to the login screen.I've tried searching the threads, but for the life of me I can't find the solution and can't remember what I did to fix it on Lucid.
View 4 Replies
View Related
Mar 30, 2010
I really like command line (I get there by pressing Ctrl+Alt+(F1..F6)) but the screen isn't full it's just a rectangle in the middle (like wide screen movies) I don't know what's the problem,
View 9 Replies
View Related
Dec 22, 2010
I have been running 10.04 quite successfully, when I upgraded to 10.10, I have a problem with the newer kernels. If I let it boot into the latest one 2.6.35-23, I get the Ubuntu 10.10 splash screen for a second then a blank screen, same with 2.6.35-22. I have to run with 32-25 to get it to load the gui.
I have an AMD Sempron 2800, 1.6GHz pc, but I'm not sure if it's running 64bit.
View 7 Replies
View Related
