I am new to ubuntu and I would really like to try it out, however I cant do the demo it freezes, I cant boot it either. I got rid of the quiet splash and watched it load. The last thing I saw before it went to just a blank screen was the ubuntu logo and it said loading apparmor then ok, went back to the previous command line screen and said done. Then it was just blank. No mouse, no blinking cursor, nothing.
View 2 RepliesIs there a known problem with the Lubuntu 10.10 image here? I have downloaded it to two different computers, then burned the images to two different blank CD's (different brands) and neither loads. Both only get as far as the Lubuntu menu, once ENTER is pressed at that point to load the LiveCD, a blank screen eventually appears with a flashing cursor at the upper left of the screen, that's it. They were both burned using the slowest burn speeds available.
View 9 Replies View Relatedlike any other Linux newb, I came to Ubuntu because my Windows crashed one time too many. And I chose Ubuntu because "it just works". But these past few days that hasn't been true. I'm posting this from a netbook with Ubuntu, and am having no problems whatsoever, but normally I use an Acer Aspire 5920G laptop. I'll include the specs as written on the sticker:
* Intel Core 2 Duo processor T5250 (1.5GHz etc)
* Up to 1024 MB Nvidia Geforce 8600M GS Turbocache
* 2 GB DDR2
Let me know if you need more details, and I'll add them later. Now, what happened was I clicked "hibernate" while leaving Firefox open. (I've done this hundreds of times, no problem) And when I went to turn it back on the next day there were weird graphical glitches in the loading screen, and it booted to the "tty1" prompt screen. I did a lot of googling and found quite a few posts about it, but the solutions either didn't work, or I didn't understand them. After trying several different suggestions from this forum and others, I managed to delete the graphics drivers. That enabled me to boot in low graphics mode, and naturally, I tried a whole bunch of things to make it work properly again. That only made it worse. Now it went straight from the loading screen to just blanking out and turning the display off. So, I tried new things. Over and over. The weird thing is even when I disconnected my harddrive and ran from a Live USB, the problem persisted. Could there be an issue with the graphics card itself? Anyway, after reconnecting the harddrive I tried to boot again. And it suddenly worked. Even HDMI to my bigger screen worked.
[Code]...
I'm attempting to install Ubuntu Netbook remix (however I have tried others) on a 32 bit laptop but after it goes through that ubuntu loading thing, it goes blank after that and I've determined that it's not the cd and it's something to do with the hardware after looking at other posts with similar issues. I do not have an operating system on this laptop.
View 3 Replies View Relatedive downloaded the Ubuntu CD from the official website and burned it twice, once one a dvd and the other on a normal 700MB CD-RW.in both, the screen went blank after the loading part before the main menu (installation, try it blah blah..)what should i do?btw i use a windows XP and here is my hardware details...sapphire hd 5770 1gb, 4 gb of ram,Intel Core i5- P55 .5 ghz, i think that its enough for the minimum of the ubuntu isnt it?
View 4 Replies View RelatedTry to load my system today and nothing come up, only the terminal window. Whatever I type in is working, like now I type in the terminal firefox and it is how I ended up here. Try to type thunderbird in the terminal and my mail server started no problem. But nothing on my screen, don't no where to go from here.
View 9 Replies View Relatedi have installed ubuntu 10.4 on my compaq 615 system successfully but when i restart the system it freezes, jus giving me a blank screen... i already have windows 7 home premium on the system then i partitioned sum space for the ubuntu but it still dosent work...
View 4 Replies View RelatedI got a new Lenovo S20 and I am having trouble loading Linux. I've loaded these variants with no success:
Ubuntu desktop
Ubuntu server
Linux Mint
CentOS
vmWare esxi
The live CD's run, and very nicely at that. But once I install to the workstation they won't boot. I just get a blank screen. I've tried different bootloaders.. I've toyed with different BIOS settings.. I've even installed to different drives (a hard disk and an SSD). Maybe a hint: BSD installs and runs with no problem at all. I have PC-BSD running at the moment. It's nice, maybe I'll keep it. But I'd rather have Linux.
My amateur computer science mind sees this as not a boot loader issue (recovery mode shows Linux seems to be loading to a point.. but I can't see the script line just before the lockup) not graphics related; UB Server and vmWare are text-only and they won't load either probably not a bios issue (liveCDs run and other people run Linux on S20s) not hardware (Windows and BSD run on this one)
I've made a Live CD of version 10.04 on a machine running 10.04 (amd64). The disk boots fine on a 2nd machine but does not boot on the machine that created it. The CD/DVD is new and works for other things so I don't think it is this. The Live CD gets to the ISOLINUX screen but instead of "Loading" the screen goes blank and the system shuts down. I've tried everything I can think of (the disk works fine on another machine).
View 3 Replies View RelatedI'm trying to build a dual boot ubuntu 8.10 and fedora 10.I have ubuntu sucessfully installed. with a free partition ready for fedora.I cant seem to get fedora past the beginning of the install. Once it says its loading anaconda, my screen either goes blank, or the anaconda fails and the install exits, telling me to reboot my system.I have downloaded the DVD twice. once from the website, and i think when I bruned it it didn't burn right, I then downloaded it from torrent just to be safe and reburned at the slowest speed. It passes the media test.
I have been reading around it may be cause of my video card?My computer is the following.AMD Athlon +2400 XPXFX Nvidia Geforce 6800 GT or something close.80 gig hard drive1.5 gigs of DDR ram.MSI Motherboard not sure of model off top of my head.I really wanna get this dual boot working, As I feel fedora may have advantages over ubuntu. I was going to try to get ahold of another video card, and maybe try that. What do you think I should do
I am having the same problem, as soon as X tries to load my screen just goes blank. I have an ATI Radeon 9550. At first I tried switching between VGA and DVI as well but upon ruling that out, I switch to my on-board video card and that is working thus far, but I'm trying very hard to figure out a way to be able to switch back. Anyways I'll check back in later on if I have any new information I will post.
View 3 Replies View Relatedreally wish to customize my GDM for ubuntu 11.4 but failed to do so.....therefore i decided to use alt. such as SLiM.....I could install it properly in virtualbox but when i went to do it on my real ubuntu 11.4 ......the screen stops at plymouth theme or goes blank after loading plymouth theme......then i read further more blogs and made changes and now even if i configure SLim the GDM starts no matter what i do .........
PS : I am new to ubuntu and dont have any knowledge about scripting programming and stuff....
When i use my computer (whether it's going online, typing, playing a flash game, or coding) I get these "Black Flashes" that are becoming longer and more frequent. A "Black Flash" is when my computer screen turns blank (but you can still see the backlight) and i have to press the NUMpad ENTER button, shake my mouse furiously, or click my mouse, which sometimes causes undesired actions, but gets me my screen back. sometimes the Black Flashes last a milisecond or 5 seconds or i have to hold the power button and restart because it won't come back on.
Specs:
Toshiba P205-S6337 Laptop
Ubuntu Karmic Koala
2.39 GB of RAM
[Code].....
I am new to linux but will try and be as precise as I can. I have a Dell Insp. 1545 with 3GB ram with 10.04_64
Problem: Rather out of the blue upon login, from the time of entering password to the desktop, is MUCH slower. I have no splash enabled and there is some reference to AppArmour profiles (it sits there at this apparmour reference , then sits trying to load desktop). However, I have never configured apparmor. Finally, on last login, there was some sort of screen corruption prior to getting to desktop.
Prior to all this i noticed that firefox "blinked" when I was using it, and then said that it needed to shutdown/restart for updates. I did notice at that time two of my previous tabs sortof acted oddly (moved around then disappeared).
I have no SSH/Server software etc activated.
I did change visudo so that sudo timeout shorter than it was. However that is the only modification to the system recently.
I have been using ubuntu wel a long time now and I know my way around in linux but I recently updated my laptop from ubuntu 10.04 to ubuntu 10.10 all went fine until I had to restart my laptop. I got a purple screen (loading screen) with 4 dots and a oldskool like font which said: Ubuntu 10.10 Right after that the screen goes purple and its like the system halts I hear no login sound etc just a purple screen. So I did a clean install from the 10.10 live cd which booted perfectly fine and the system was also useable like before. But when I installed the system and rebooted it again no problems.
But when I tried to install the proprietary nvidia driver (the recommended one) I got the same problem again the purple screen. After searching a while on the internet I only found posts which had the problem with ATI cards but my laptop is fitted with a Nvidia Geforce 9300 M card. So I tried several things like removing the xorg.conf (read it somewhere) which ofcourse did not work, and booting in graphics fail safe mode which worked. So the point is in 10.04 and 9.10 I CAN use my video card drivers but not in 10.10 is there a solution to this problem? I am talking about the 32 bit version of ubuntu and here's my system hardware profile:
Intel core 2 duo t7350 @ 2,0 ghz / 3mb l2 cache
2 GB DDR3 ram
160 gb hdd
Nvidia 9300m gs
Chipset: I dont know sorry
Model: Samsung R710
The day started as usual until I got the very bright idea to install Ubuntu. A new OS along side W7, that sounded great. I checked some guides on the Internet, it was all very straight forward. Install it and Grub will show you the OS:es when you boot up. I installed Ubuntu, rebooted. After the BIOS messages the screen goes blank and my screen on-button begins to blink, as if trying to find a signal, I press enter, it reboots instantly. After BIOS messages I get to a screen that says "GRUB error: uknown filesystem grub rescue>"
I've looked through everything here and nothing works. I've tried to fix the mbr-thingy using Windows Repair and even though it says "one partition was updated with new boot-thingy" when I reboot, I get into that very same grub rescue. I think my setup has something to do with it. I run RAID0 (2x360Gb hard drives), first having C: at 50Gb and then the rest as F: for programs and such. What I did was that I shrunk the F: part and then used that as partition for Ubuntu. Also please have a look at these screenshots, my partitiontables and such seems completely wacky to the raid: Where should the boot-loader go? I'm very, very new at this. I've had Ubuntu Netbook remix on my netbook for a time but still treat me as an utter beginner.
I'm trying to test out using xubuntu 10.04 on my one computer and keep getting a black/blank screen after selecting the 'try' menu option.Is there a way to fix this?I have tried some of settings via F6 with no luck.
FYI -The CD works fine as I have tested it on other machines.The version I am trying is xubuntu x86 (although I have tried ubuntu 10.04 x86 with similar results).I can Alt+Ctrl+F1 fine and get to the cmd prompt
I fixed this issue on 10.04, but just recently (1 hour ago) upgraded to 10.10 and am having the same issue. Machine boots fine, but the screen is blank for most of the boot, and plymouth is up for about a half second before I get to the login screen.I've tried searching the threads, but for the life of me I can't find the solution and can't remember what I did to fix it on Lucid.
View 4 Replies View RelatedI have been running 10.04 quite successfully, when I upgraded to 10.10, I have a problem with the newer kernels. If I let it boot into the latest one 2.6.35-23, I get the Ubuntu 10.10 splash screen for a second then a blank screen, same with 2.6.35-22. I have to run with 32-25 to get it to load the gui.
I have an AMD Sempron 2800, 1.6GHz pc, but I'm not sure if it's running 64bit.
I've been running Ubuntu 10.10 very smoothly for a while now. Decided to upgrade to 11.04 - managed to corrupt the hard disk the first time by letting the laptop hibernate part of the way through but reinstalled from a live CD of 11.04 and it's now working except for this issue.
If I shut the screen on my laptop (or press the screen off button) either the screen won't come back on or it will but frozen (I can move the mouse but not click on anything etc.) In this state music continues to play (from spotify under wine) and if I press my hibernate shortcut (power button) the computer hibernates, only to wake into the same situation. I've got a Dell Latitude D520, upgraded to a bigger hard disk and more ram - the ubuntu partition has 50gb. Windows is working fine.
Edit: I noticed a sticky thread which includes something about a blank screen but I think this is a different issue?
i have just put a Geforce 7300 GT graphic card into my machine the problem is the max resolution I can get is 1024x768 at 60 hz the screen is a benq fp71g+. also the screen goes blank when i click on the display icon in system settings. i know that the screen can be run at 1280x1024 so I don?t know where the problem is.
View 3 Replies View RelatedUnfortunately my experience in the Unix* based world up to this point has only been using web servers and administrating them, no GUI experience of any kind so I am completely unfamiliar with the setup and entire usage of Xorg or any other Window manager at this point. The issue I am having is with the screen resolutions I am being allowed to chose for my Dell Studio 1535 running Fedora Core 13 and the KDE 4 desktop GUI, thus my issue since I am not really familiar with how to run a Unix* based GUI in the first place.
The basic information, if there is more needed just advise what and what command gathers that info (or what conf/log I should look into in order to find it). Laptop is a Dell Studio 1535 Video is the Mobile Intel GMA X3100 ATI Radeon HD 3200 Graphics. LCD interface is the LVDS.
So far it seems to give me modes for 1024x768 and on down, nothing above this. I believe I am supposed to use the radeon driver being that is the type of card it is but every time I change the xorg.conf file to use this instead of vesa the system wont get past the loading screen anymore upon reboot and nor can I seem to find a way to bring up a command line so I can hit up the Xorg.0.log to see what is wrong or change the xorg.conf file back to the original driver it had listed.
I am going to assume this is a missing driver or something else it hangs on but without being able to get access back to the system and having to rebuild it again (re-install via live CD) I am basically out of luck at this time. Sorry for the rather poor post but I do hope to receive some basic directions on where to go from here with this issue
another post about this. I just don't know how to handle this, as I'm pretty nsee the grub loading menu, but screen just freezes after, no way I can reboot, or open a console. In recovery mode I can log as root in console, though.I run Debian 6, 64 bits. I have an intel q6600 and a nvidia geforce 9800GX2.
View 9 Replies View RelatedI have installed Ubuntu 11.04 along side windows 7 ultimate. But the problem is as soon as I switch on my computer. There is only a blank screen with my TFT screen displaying a msg "Out of Range"
Then suddenly Ubuntu loads without showing any option to load windows 7.
My problem is that I can't log in to Ubuntu, as you've already seen in the title. Here's what's happening:
I turn on the computer. I see the GRUB. I press Enter. I see a blinking underscore (_) as if i was in a terminal. The underscore disappears and I can see my cursor, but nothing else. I can move the cursor, but that's all I can do.
I've seen some similar problem here on the forums, but he could log in, he just couldn't see the screen.roblem!
OS: Ubuntu 10.04 LTS, kernel 2.6.32-31-generic. All updates are current.
Configuration -CPU: Intel Core i5-2500K, quad core 3.30GHz
Memory: 16GB RAM (10% used), 20GB swap-space (0% used)
Video: Two ASUS EAH5450 Silent cards, each with ATI Radeon HD-5450 GPU and 512 MB
Monitors: Sceptre 22", 1680x1050; both connected to one video card. The second video card has no monitors connected at this time.
ATI/AMD proprietary FGLRX driverLSPCI output -
[Code].....
The PC boots up normally into Gnome desktop environment. When I hit ctl-alt-[F1-F6], -The screens blank out. One screen gets no video signal, as evidenced by a blinking power light The other screen is completely blank (not even a blinking cursor) If I hit ctl-alt-F7, I get the Gnome desktop back. I have been able to determine that even if the screen is blank, and appears completely dead, the system processes my keystrokes. For example, if I pretend that I am at the log-in screen and type <username> <enter>, then <password><enter>, then 'xinit -fg white -bg blue -- :1 vt8'<enter>, the PC switches to virtual terminal 8, and shows a shell window. From that point onwards, my keyboard entries show up in white-on-blue characters, and the behavior of this shell window is perfectly normal. I can log into another Linux box using ssh, start a Gnome / KDE / XFCE4 / LXDE session and work on the machine normally; or start another X-session and a desktop environment of my choice. My guess is, the console is invoked perfectly well; it is set to display black-on-black characters.
What I Am Looking For:Confirm if my guess about black-on-black console is valid.
Suggest how I could get a screen showing white characters on black (or indeed, any combination I could read)
I've recently installed the 64bit version of WUBI on ASUS K50IJ with windows 7. Everything went smooth however when I try to boot into ubuntu, it shows that all the drivers are loading, I can even see the desktop background image for a second and then the screen goes blank. It is still ON however nothing is showing on it.
Pressing "CTRL+ALT+DEL" reboot the system.
even get access to the console for further debugging?
Anyway one day I start my computer and instead of starting normally it comes up with a screen which says GNU GRUB version 1.97~beta at the top. I selected the option Ubuntu, Linux 2.6.31-19-generic as I figured this is what normally loads without being prompted in the grub menu, but after this I got the ubuntu logo for a few seconds then my screen goes blank. My laptop is a hp510.
View 9 Replies View RelatedI'm a newbie so apologies if there is a trivial answer to this.
I (maybe somewhat rashly) tried to connect my tv to my laptop (Dell Latitude D400) running Ubuntu 9.10.
I plugged in the cable, went to the System>Display menu, where it had detected the model and make of tv (Samsung 19" LCD) (I think the resolution was 1650 x 1050 or similar). I clicked the box to activate the second monitor with the "Virtual resolution" adjusted. It told me to log out then log back in.
I accordingly logged out but then couldn't log back in. It had evidently changed the resolution not only on the 2nd monitor but also on the laptop monitor. A box was visible on screen but completely illegible/unclear since the laptop monitor couldn't display that resolution.
After a few restarts and button pushes it is now restarting at a terminal (I enter my username/password at a command prompt on an otherwise blank screen rather than the graphical interface loading up).
Question: are there any commands that could change the resolution back to its original settings then restart the Ubuntu graphic interface? Some thing similar to the "load with last known good configuration settings" option in Windows maybe.
I was just surfing the web the screen suddenly went blank and then the clock went off.
View 2 Replies View Related