I just bought a gigabyte sniper motherboard and when I installed ubuntu 11.04 it does not recognize my internet bigfoot E2100 1 x Bigfoot Killer E2100 chip.
View 5 RepliesI just replaced my motherboard with a Gigabyte 890GPA-UD3H. I am happy to report that the OS (Ubuntu 10.04) was smart enough to boot up using the pre-existing software RAID 5 (four disks) and work fine with the new motherboard, CPU, and memory. However, since the new motherboard has a nice onboard display, I removed the PCIe graphics card (which was needed on the old board), and am now trying to configure the OS to use the "OnChipVGA."
This is what lshw produces
And here is what I get with startx:X.Org X Server 1.7.6
Fatal server error:
I've got an old laptop wich wireless adapter is a Gigabyte GN-WI01 GS MINI PCI(its chipset is Realtek RTL8169/8110, I believe) and I'm not able to make it run in Wifislax 3.1 Live CD. I downloaded the linux drivers for it and tried to install them following the instructions but when it came the time to execute configure.sh it told me that I had to actualize some kind of packets first(GK+ or something like that can't remember ). I also have another wireless usb adapter that I tried to use too. It's a Linksys WUSB54g v4(chipset: rt2570). I tried to follow a guide I found about making run an adapter like that on Wifislax 3.1 but when I had to "Force ralink rt73 on rt2500" it doesn't appear on my Live CD version, it appears "Force ralink rt73 on rt2570", dunno if it has something to be but I get an error while making it.
I don't know if it has to be with my laptop, my wireless adapters or my way of following the steps. If it has to be with my adapters I would like to buy some new one(not very expensive) that I won't have any problems running it on Wifislax and that will work on my old laptop(cause I just have that one and can't afford a new one).
I have installed Ubuntu 9.04
uname -r
2.6.28-11-generic
Checked cable/network with 386Box running Ubuntu 8.04 all OK. Could not get Realtek 8168 on mother board to work on Gigabyte H55M-S2H motherboard. I tried to install r8168 driver but no luck ... so I bought another Linux compatible card which turned out to be a RTL8139c (eth1) and the driver I am using on this is card is 8139too.
[Code]....
My preference would be to get the motherboard ethernet working but perhaps the card may be easier to get working. Anyway after searching the net for ideas and trying different things I've just about given up. I have reinstalled Ubuntu today so eth0 is back to using the r8169 driver. I'm no expert so my attempts at following other recipies have so far failed. From what I have read the 8139too driver should have worked with the RTL8139C chip so I have run out of ideas. I must be doing something wrong.
I just built a computer and the onboard nic pluggin is loose and won't register or connect right... so I had to put another nic card in pci to connect to wired network for internet. Problem now is its delaying something fierce... i'm thinking if i can manage to uninstall or disable the onboard nic maybe things would work better... problem is i wouldn't know how to do it... I know hardware is connected via a document somewhere in the file system... if I were to delete the file would that disable the nic or would it just reinstall itself on the next boot?
View 1 Replies View RelatedI want to start using Ubuntu again but I gave up ages ago trying to get it to work with my Gigabyte EP45-DQ6 motherboard.I cant run from disc and I can't install.If I try to run it just takes me to a black screen with blinking cursor and that's all it does.If I try to install, basically the same.I can't get anywhere doing anything, so where do I start?How can I get it working on my system?By the way, this is with the latest Ubuntu.No, it's not a corrupt download or burn. I tried to download and burn, didn't work.I ordered a free cd, it did the same.This is an issue that is NOT related to the disc or the download of Ubuntu.
View 9 Replies View RelatedI have had this problem for far too long, my onboard sound will not work, i went from Xubuntu, to Vista now to here! NO the mute is not on, it says i have sound but I dont! I did the lspci command and got this:
ALSO I have a custom built computer that came with a Rocket Fish sound card model RF-51SDCD that I rip out (no known drivers for that sound card). I have a Compaq Presario 061. Model number is DT076A-ABA S6200CL NA410. My motherboard is an ASUSTek Kamet2. The firmeware is Phoenix Technologies version 3.05 (cant find an update for that either).
I wanted to type something in french so I started the on board keyboard so I'll know where the letters are. Now my keyboard is locked, and the onboard doesn't work too... all I did was to click on some of the settings of the onboard.Sadly the onboard didn't show me the french keyboard, so that's a downer too.
View 1 Replies View RelatedI'm running Ubuntu 10.10 with an EVGA nForce 730i Intel mobo with onboard HDMI. Video output works. Audio output does not. I'm trying to output both to a Samsung HDTV.
I tried booting to a bootable drive with Ubuntu 11.04, and no audio.
I've essentially tried everything in every other thread. I'm using alsa mixer, I've muted S/PDIF, my settings all have HDMI output selected.
sudo modprobe snd-hda-codec-nvhdmi results in:
Code:
aplay -l results in:
Code:
aplay -L results in:
Code:
Also tried aplay -D to play a .wav, and heard no sound, but also encountered no errors.
I'm having trouble getting X to work after switching from onboard intel video to a 5000 series ATI card. Apparently I need to switch to a MESA or fglrx driver. I did a sudo apt-get install fglrx-driver and it installed but still no X. I'm currently using Karmic. I've tried to boot with a live CD which works fine and changed the xorg file manual but that was a mess.
When I start I get a checking battery state ... done and it stays there forever sometimes and sometimes I can login but without x. Typing startx gives me a long list that says check the xorg website. I've been looking around for a way to fix this and haven't been able to get it working.
I bought a used Dell Precision T3500 after I had a positive experience with it at a previous job. Since my AMD motherboard died recently, I'm interested in using the Dell as my full time machine.
However, I cannot seem to get my PS/2 keyboard to work; this is crucial as I use a fully mechanical keyboard and need my N-key rollover that PS/2 provides.
The weird thing is that the PS/2 keyboard works perfectly during a text-based installation of Debian GNU/Linux. When I boot into a newly installed system if I press any key on my keyboard my Caps lock and scroll lock LEDs flash and no keystrokes are registered (?).
I bought a used server and it's in great working condition, but I've got a 2-part problem with the onboard raid controller. I don't have or use RAID and want to figure out how to stop or work around the onboard SATA raid controller. First some motherboard specs.: Arima HDAMA 40-CMO120-A800 [URL]... The 4-port integrated Serial ATA Integrated SiliconImage Sil3114 raid controller is the problem.
Problem 1: When I plug in my SATA server hard drive loaded with Slackware 12.2 and linux kernel 2.6.30.4, the onboard raid controller recognizes the one drive and allows the OS to boot. Slackware gets stuck looking for a raid array and stops at this point -........
I had U10.10 installed prior to running U10.10 Desktop, and the wlan worked flawlessly on that.My understanding is that the packages are the same and so this should be installed with Desktop, however it will not action the final connection. The wlan is finding networks and prompts for the Key when connecting, but it never actually connects.
Quote:
sudo lshw -C network
gives the following:
Quote:
*-network
[Code]...
I have a Lenovo W510 loaded with Ubuntu 10.04 but it does not detect my onboard 3g modem
View 4 Replies View RelatedThis is my first attempt switching to Ubuntu from Windows, and I am having some trouble getting the on-board ethernet to work in Ubuntu 9.1. I have a MSI KM2M Combo-L VIA KM266 and VT8235 Chipset which uses the Rhine II chipset. I am trying to use the onboard ethernet, however it does not connect to the network after installing Ubuntu, although the driver appears to have been automatically installed. I also tried this with several other network cards (Intel, Dlink, Netgear) with various chipsets, but none seem to work.
Our network Netgear switch/router has DCHP enabled, and all of the Windows computers connect just fine. This is true even when we plug another computer into the ethernet cable serving the Ubuntu computer. When I manually configure the IP address, it shows the network connection as connected, but it is unable to ping and/or connect to the internet (except for localhost and the assigned IP address). I used 192.168.11 as the IP, 255.255.255.0 as the netmask, and 192.168.1.1 as the gateway. Below are several commands, that I've run to provide some additional information (using auto eth1).
[Code]....
I am facing problem with onboard lan card. i think its not detecting. when i type ifconfig command it shows below details
I have installed red hat. but not able to give ip.
I have used a wireless LAN PCI card for 3 years and now I want to switch back to the onboard wired LAN card but I cant get it to recognize and I have enabled it in BIOS also the wireless LAN card has been removed.Should I put it back in and then try to switch?
View 6 Replies View RelatedI want to know if there any way to find out interface of Linux Box(Suse 9>)is onboard or externally attached (pci slot)?
Note:- This is a problem which I am facing in my work. In onsite server we need to configure n/w card too. So some time when we configure, I'm confusing which interface should be configured. Client insisting us to configure embedded(onboard) interface. How to find out that.
I have two onboard gigabit Ethernet ports and 3 10Gb add-in fiber ports. When everything is cabled but nothing is IP'ed yet, I do an ifconfig -a and the two gigabit ports are showing as "__tmp2143330114" and "__tmp1076785124", eth0, eth1 and eth3 show as the 10Gb addin cards. On other (identical) servers, eth0 and eth1 are always the gigabit ports and eth2, 3, and 4 are the 10Gb ports. Anyone know what is going on?How can I make sure that Red Hat detects and assigns these ports correctly on boot, or at least can I reassign what ports are designated eth0-eth4?
View 6 Replies View Relatedwas assign to set up a network server that has 4 land card including the onboard 3 dsl connection
View 1 Replies View RelatedI have installed Fedora 14 on Intel's DH67BL mother board, which has a on board LAN port, Fedora 14 does not detect on-board LAN. Unfortunately, intel does not provide any driver support for linux OS :-(. However, if I install an additional LAN card, Fedora 14 detects it and everything works fine.
View 5 Replies View RelatedI'm running a fresh install on an intel i7 system on an asus p6t deluxe v2 motherboard with the onboard NIC (Marvell Technology pci-e). I know the NIC is working as when I boot into the onboard OS that Asus provides (Asus Express Gate SSD)I have a working net connection.Booting up CentOS hangs at determining IP information for eth0 and eventually fails with the following error:PING xxx.170.30.1 from xxx.170.31.231 eth0: 56(84) bytes of data---xxx.170.30.1 ping statistics ---4 packets transmitted, o received, +3 errors, 100% packet loss, time 2999ms, pipe 3 failed.
RTNETLINK answers: file exists.
RTNETLINK answers: file exists.
RTNETLINK answers: file exists.
[code]....
I am running FC13 on a Compaq Presario 2100 using a Broadcom BCM4306. I was able to get it running thanks to Fedora Unity Project. But It's a very unstable connection. I don't know what settings to adjust or enable or disable. It's not my router, this is the only wireless connection in the house that I have trouble with.
View 1 Replies View RelatedOn my computer was 2 gigabyte memory and I bought still 1 gigabyte memory. In the Ubuntu show only 2.75 instead 3 GB.I have old computer. P-IV but in the manualook for my motherboard say that can use to 4 gigabyte of memory. I have 2 questions.Why in the Ubuntu don't show all 3 GB memory?If I buy still 1 gigabyte of memory, itshe will show 4 GB in the Linux or not?
View 8 Replies View RelatedThis thread [URL].. was the only one I could find on this forum that addressed the problem I am having. It also involved a Gigabyte motherboard. I recently purchased a Gigabyte GA-MA770T-UD3 motherboard which is a version 1.3 . I have a v. 1.0 of the same motherboard which I have used regularly for a year.
The problem I have is that newer versions of Ubuntu (10.04 and 10.10) don't boot reliably with the new motherboard. It will boot up to where it says "Begin: Running /scripts/init-bottom. Done." and then will stop. If I hit any key on the keyboard the boot finishes and everything is OK. Sometimes it will hang like this but often it will boot successfully without assistance. I need it to boot by itself reliably every time.
Older versions of Ubuntu (8.04 and 9.04) boot just fine with the new board. If I put the drive with the 10.04 installation in my older Gigabyte v.1.0 computer, it boots reliably every time. Interesting to note that Windows XP sp1 installs fine on the older v. 1.0 computer but I need XP sp2 in order to do a successful installation on the v 1.3. I have stress-tested the new setup for 6 hours without incident and memtested the RAM for 4 hours without error. I have even swapped RAM between the two with no resolution.
I can't find any thing in syslog to explain this. It stops just before the splash screen comes up. I removed splash with no positive result.
one2busy here, Just got a Gigabyte GA-P55A-UD4P Mb and Core i5 750. Originally had XP, then Win7, then Win7 64bit ..... all work fine. Tried to install Ubuntu 10.04, when partition section popped up it did not detect either of my Hitachi SATA drives..I went to the website and the website for this Bd, at the bottom of the page, it says that 3rd party drivers are needed for linux. Does anybody know anything about this?
View 9 Replies View Relatedi just got a new motherboard : gigabyte ma78lmt-s2 with amd760g chipset, athlon and 4gb ram
the sound codec is hda ati sb alc887 from realteci'm now already 4 days fiddling to get the sound working in ubuntu 10.04 lts without any success / progressalso the gigabyte ma78lmt-s2 is not booting from a usb stickafter 2 weeks hopeless the ma78lmt-s2 is not recommended for linuxexchanged the gigabyte ma78lmt-s2 for a biostar a880g+ and everything works straight from start
I have a Gigabyte P5100 GT Tv Tuner and i can't activate it on ubuntu. i've found drivers for all my other devices but not for this. i've searched on many sites, but no result. ubuntu also can't find itself with "software sources" or other like this.
View 2 Replies View RelatedI installed a bunch of hfs/hfs+ software and wanted to make an hfs partition. The problem is, GParted only lets me make a 2 GB partition on a 250 GB disk. Why is this so? Is there a limitation in the software, and is this that limitation?
View 2 Replies View RelatedI'm finishing setting up my new computer.I'm installing ubuntu 10.04.The motherboard is a gigabyte GA-H61M-D2-B3When I plug the computer into my stereo, I get a horrible scratchy buzzing.How can I get rid of it?More info on hardware: Quote:lspci -v | less gives a lot of output, including this:Quote:
0:1b.0 Audio device: Intel Corporation Cougar Point High Definition Audio Controller (rev 05)
Subsystem: Giga-byte Technology Device a002
[code]....