I have install ubuntu 9.10 on my Dell studio, I have local broadband connection with its user name and password which i use to connect internet everytime i need along with its IP Address, subnet mask, Default gateway, Preferred DNS server. Where should i put all this details to connect internet, i have already tried with Network connection in System -> Preference . It all work well in window
View 9 RepliesMy father recently installed Ubuntu 9.10 on my new AMD dualcore, but we have not been able to access the net.we tried resetting the modem/router. Windows XP had no problem getting us online - why is it such an issue with Ubuntu?
View 3 Replies View RelatedI cant configure internet connection.
View 3 Replies View RelatedI am using ubuntu 8.10 ....
i am unable to configure my internet on it ..i have tried a lot of things, which i have are as follows...
1. i used these commands but unfortunately no result... sudo ifconfig eth0 192.168.1.21 $ sudo route add default gw 192.168.1.1$ sudo vi /etc/resolv.conf this file is edited to enter ipadd etc....
2.Setting the ipaddress in system>admininstrator>network config
there i edited the properties of "Auto eth0" for my ip address, mask, and default gateway....
P.S: My internet connection is perfectly working fine in windows xp. Details shown in windows are :
ip address : 192.168.1.21
mask :255.255.255.0
gateway :192.168.1.1
dns :59.179.243.70
Laptop : Dell XPS m1330 OS : RHEL5 I am not able to configure wireless internet connections.
View 2 Replies View RelatedI just switched from Ubuntu to Fedora 13 because I was unable to get Ubuntu to connect to wireless networks. I tried everything suggested in help and forums, and kept getting "Bad Password" with WICD and Network Manager. Now, with Fedora...I still can't connect.
Problem #1: The guide says to "...make sure that the relevant wireless interface (usually eth0 or eth1) is controlled by NetworkManager," and that I do this via: System>Administration>Network
However, there is no Network option under System>Administration.
Problem #2: I open Network Manager, which displays a list of networks. I click on mine, configure it with WPA and the right password, and it fails to connect: "The network connection has been disconnected."
I m new to Linux and I wanna to configure DSL modem wired connection in Ubuntu Please help
View 2 Replies View RelatedI've installed Ubuntu 10.04 on my classmate's Lapie after he got frustrated with Windows 7
Everything is fine except LAN connection wired one...
Can anyone tell me how to confiure that..& from where ?Like his IP addressis 192.168.68.10 with subnetmask 255.255.255.0
Plz guide me for this...Bcz many of my fellow hostelmates are for Ubuntu if I configure it out.
I wonder how should I configure my laptop to connect to the Internet wireless.
View 2 Replies View Relatedi am having problem with setting up an internet connection on ubuntu plateform , presently i am running internet on xp plateform and want to switch to ubuntu plateform . i am connected to the internet through broadband connection by using modem. it's a dsl connection so plz tell me how to configure internet connection
View 1 Replies View RelatedI'm trying to configure internet access using KDE network manager. Added new VPN pptp connection, set gateway and other options but manager tries to connect for about a minute and breaks then. Here is /var/log/daemon.log
Code:
Jul 1 17:35:22 dvinokurov-desktop NetworkManager: <info> Starting VPN service 'org.freedesktop.NetworkManager.pptp'...
Jul 1 17:35:22 dvinokurov-desktop NetworkManager: <info> VPN service 'org.freedesktop.NetworkManager.pptp' started
[Code]....
As I understand the main problem is in "(IP Config Get) timeout exceeded".
Configuration: Kubuntu 10.04 x86, VPN server with MSCHAPV2 auth, no compression, no encrypting.
I am really bothered from this I cant configure the 2 nics to share the internet and I already changed the sysctl.conf file to
# Controls IP packet forwarding
net.ipv4.ip_forward = 1
I have one nic reeving the internet and working good and the other one cant see anything...
I have wireless adapter USB rt1878 working fine.I have to setup pppoe to make internet connection?I need this help?
View 3 Replies View Relatedi configured my laptop (running UBUNTU 10.04 LTS) for my broadband (bridge mode). I did that using PPPOE CONF command. Everything goes ok but only prob is i have to run this command and configure my net every time i restart my system. What i need is it should connect to the net whenever i use the PON DSL-PROVIDER and must turn off by using POFF..
View 1 Replies View RelatedI just installed Lucid Lynx Ubuntu on my computer. I love it, but I do not see how to configure my dial-up modem and connect. I'm hoping it's still possible. Here's my hardware.
333mHz Pentium III
Lucid Lynx 10.04 LTS
US-Robotics 56K Faxmodem External
256mb RAM
ISP OmniLEC
I have wireless adapter USB rt1878 working fine.I have to setup pppoe to make internet connection?I need this help?
View 1 Replies View RelatedI am using DELL Studio 15, Windows Vista Home Premium. I have a dual boot of Linux (RHEL 5). My question is how to configure Internet access in my PC in LINUX OS. Windows mode :
how do i access Internet :
I insert a LAN cable to my laptop and access internet. or I insert the cable to my wifi router and access it wireless whenever I am bit far away. RHEL 5.0 Linux 1) UNABLE to access internet when I connect the lan cable to my laptop. 2) Is there any way i can access internet or should i use any drivers that are provided my dell pc. I am very new to linux and i am not sure to which and how to use it.
I have tried various rules, like opening port 53 for the DNS with little success. I finally figured that you need to set the source port to 53 and NOT the destination port.However, I have been unable to figure out what ports apt-get requires. The only way I get it to work is to accept everything in iptables.
View 1 Replies View RelatedI have attached the screenshot of the option which I select in Windows for making the same internet broadband connection. I am unable to find the same option in Ubuntu 10.04. Till now I was using the Pppoe Dialup. But now I am unable to configure this one.
View 9 Replies View RelatedI have a dynamic IP connection. so i got hostname on [URL]. Now i want to configure a ftp server with that. I am choosing following options in the network configuration wizard:
1. default transer mode: passive
2. use server's external ip instead
3. get external ip address from the following address: XXXXXX.dyndns.org
4. ask opearting system for a port
5. test result:
[Code]....
I have a router which have 4 ethernet ports(eth0,eth1,eth2,eth3,eth4 ) & One ADSL Line & One USB, I need to configure My router eth3 as a WAN & eth0 as a LAN using iperf, I am going to findout test a my Application(using iptables) whether my application is correct or wrong As of now I configured like server pc1(192.168.1.230)--->eth0(gw)(192.168.1.1)Router--eth3(gw)(192.168.2.1) -->pc2(192.168.2.157). For eth3 as a WAN and eth0 as a LAN. But I am not able to ping between two pc's.
View 1 Replies View Relatedi am using fedora (2.6.35.6-45.fc14.i686), i am not able to configure the usb based wireless adapter, its DWA 125(Dlink) uses ra chipset.
lsusb
here is the output
Bus 001 Device 002: ID 07d1:3c0d D-Link System DWA-125 Wireless N 150 Adapter(rev.A1) [Ralink RT2870]
i have got the driver loaded with the help of modprobe, still unable able to make it right. when i use system-config-network - wireless - no sign of RT2870.
How to install kerberos on a local machine...?
View 2 Replies View RelatedI have a desktop and a laptop. I have Netgear WGR614v9 Wireless Router connected to my desktop. Since my Laptop is pretty old I also bought a Netger Wireless Adapter for the sme model. Now when I connect the Wireless Adapter I am unable to connect to Wi-fi. I am new to Linux, after googling I ran "lsusb" command and it showed Netgear Wireless adapter and its version. Also in GUI when I open File Browser it also shows the Adapter detected but I am unable to connet the same to my router. Also the blue light on the adapter is not glowing.
View 6 Replies View RelatedAm using Fedora 15, in which i was able to configure the proxy server and authentication. i confirmed this by configuring web broswer and it works. Now the problem is that i want to deploy it out to other computer system(client) i dont want to use the transparent proxy because the Proxy Authentication will not work.
I even tried to configure a DHCP server if it will work but i cant still configure for other computer system to work.
I could not able to configure the default gateway ip address onto the system. i use the route command (" route add default gw 192.xxx.xxx.xxx eth0 ") to add a default gateway onto the routing table but it is "disappear" in the routing table when i had restart the service network.
View 3 Replies View RelatedIt is a wired connection through Time Warner and worked flawless with XP. It will not load any page except for google.com homepage and I cannot access any of the links in the search results of google. I know the internet works since google will load and I have done all that I can think of (ping and manually enter my connection) and nothing works. I am running the OS on a Acer Aspire M1610 desktop.
View 7 Replies View RelatedI have installed Linux SuSE 10.3 on a PC (Lenovo Thinkstation A58). However, when I start the computer I get the following error message:
"No valid Host_ID or host-name found."
I then use YaST to set up the network. I get the following error message:
"Unable to configure the network card because the kernel device is not present."
The computer has Windows 7 installed and everything seems to work fine. The LED on the Ethernetplug is blinking when using Windows, but not when using Linux. I guess this means that there is no driver for the Ethernet card (Marvell Yukon 88E8057). I have not found any driver for the card and am considering buying a new one. Which PCI card works with SuSE Linux 10.3?
I am a first time Linux user - though I've Unix and Windows experience. So though I can follow your most tech instructions, I'll need some hand-holding.
Need help getting my wireless network to work on my newly installed Oracle Linux on Dell laptop.
Not sure what wireless card is installed, or it's mac address (though I can boot into windows and get that info, I don't want to - it'll be kind of a let down if I can't fix it all thru Linux).
Install has detected a Broadcom wired card, but not the wireless. Funny thing is that it detected the Bluetooth.
Currently I have an Acer Aspire One netbook with Windows XP on it. I want to switch to Ubuntu, so I have the OS on a flash drive and I can run it fine. The only problem is,I cant see any wireless networks in range. I know the router is working because I can connect with Windows fine. A notification also pops up telling me i have to install missing drivers. But when i click on install, the progress gets to 99% and fails. It says i need the Broadcom B43 driver, but i don't know how to get it.
View 8 Replies View Related