In nvidia-settings I see, alongwith Disabled and TwinView settings, "Separate X Server". I tried choosing the option for my LCD (connected via HDMI), but I get a blank screen, presumably since the LCD's X server has nothing to render.
How do I direct any application (say vlc) to use that X Server instead of the Monitor's X server?
I am using Fedora 13 x86_64 on a Acer Aspire 7730ZG laptop with: 01:00.0 VGA compatible controller: nVidia Corporation G98 [GeForce 9300M GS] (rev a1) I have kmod-nvidia-2.6.33.6-147.2.4.fc13.x86_64-195.36.31-1.fc13.2.x86_64 installed from rpmfuison when I plug in the hdmi cable to the tv, my tv says the resoultion is at 720p, and I can not get any of the resolutions settings to look right on seperate x screen with the nvidia X server settings gui. my tv is a vizo 42inch. also another question is their a way to set the video card to output at 1080? this might be part of my problem?
View 14 Replies View RelatedI currently have a problem with my nvidia settings
I reinstalled 11.04 kubuntu recently and I no longer could use my second screen.
I looked into my nvidia settings and enabled my second screen (separate x screen).
However when I do so and press apply the second screen does nothing.
This is two desktop monitors and not a laptop and a monitor.
I am running Slackware X68_64 and I just purchased a second monitor. I enable separate x screens with nvidia-settings and when I reboot I get a black screen and when I put my mouse over to the secondary monitor I get X for the mouse pointer. Than after a while it just blacks out.
View 11 Replies View RelatedI have 2 monitors, a 22 inch samsung as my main and an acer as my alt. I am trying to get the samsung monitor to display, but is is disabled. So I enable it as a separate x display, then save, but when I restart x, the settings didn't save. I save the config under under /etc/X11/xorg.conf. What am I doing wrong?
View 4 Replies View RelatedI have a Dell E6500 laptop (1280x800 screen), which I frequently dock.The dock as two Dell 1908FP 20" monitors connected by DVI. I can move between the laptop display and the twins by manually changing display configuration in NVIDIA X Server settings, but this is a pain requiring about 15 clicks each time.
I have tried using the "Save to X Configuration File" option in the Nvidia server settings, but this seems to screw everything up. I need to dynamically change between the setups... anyone have advice on getting that done?Can the xorg.conf file be configured to do it?My xorg.conf looks like this:
Section "Screen"
Identifier"Default Screen"
DefaultDepth24[code]......
I'm trying to set up a simple local email service on a small office client-server network. Can I use sendmail without setting up a separate DNS server. If I need a DNS server can I set it up on the same computer as my sendmail MTA? Can it be a private DNS server?
View 1 Replies View RelatedStill pretty new to this, from what i have read, the more info i give the better, I am running ubuntu 11.04 with KDE installed via the terminal. I was trying to get my TV to work as another display, I don't know what I have done, after my earlier problems I have learnt to back up and restore my xorg.conf file but with no luck, I now can't change any settings as the title says the apply button is grayed out and when i try and save it to the xorg.conf file and restart the xserver it says that "Your current changes to the X server display configuration may no longer be applied due to changes made to the running X server.
You may either reload the current X server settings and lose any configuration setup in this page, or select "Cancel" and save your changes to the X configuration file (requires restarting X to take effect.)
If you select "Cancel", you will only be allowed to apply settings once you have reset the configuration.Your current changes to the X server display configuration may no longer be applied due to changes made to the running X server. You may either reload the current X server settings and lose any configuration setup in this page, or select "Cancel" and save your changes to the X configuration file (requires restarting X to take effect.)
If you select "Cancel", you will only be allowed to apply settings once you have reset the configuration. Your current changes to the X server display configuration may no longer be applied due to changes made to the running X server. You may either reload the current X server settings and lose any configuration setup in this page, or select "Cancel" and save your changes to the X configuration file (requires restarting X to take effect.)
If you select "Cancel", you will only be allowed to apply settings once you have reset the configuration."
when I booted last i got terminal with this showing, for the first time,
Xlib: extension "RANDR" missing on display ":0".
(orca:1984): Wnck-WARNING **: Property _NET_WM_NAME contained invalid UTF-8
My xorg.conf is
# nvidia-settings: X configuration file generated by nvidia-settings
# nvidia-settings: version 270.29 (buildd@roseapple) Fri Feb 25 14:43:24 UTC 2011
Section "ServerLayout"
[Code]...
I'm running dual-screen. On 24" at 1920x1080 and one 19" at 1440x900. After installing Mint 9 I can't set the resolution any higher than 640x480 in nvidia-settings. I've installed the "recommended" nvidia-driver that Mint suggests.
[Code]...
What could be the problem? Why can't I set the res higher than 640 in nvidia-settings? Everything worked in Mint 8 (10.04). During installation the res was higher than 640.
How do I do this? You do not appear to be using the NVIDIA X driver. Please edit your X configuration file (just run `nvidia-xconfig` as root), and restart the X server.
View 3 Replies View RelatedI plugged the usual 4-pin s-video cable into my TV and graphics card. I went to nvidia x server settings, nothing. I hit detect monitors, nothing. I changed the TV to the proper input channel, Nothing. It's a bit annoying,I used it with the old GeForce Ti4200.
View 1 Replies View RelatedI just bought a new 24inch monitor that supports the resolution 1920x1200. Unfortunately, the nvidia-settings dialog does not have this resolution as an option (currently running on 1920x1080). The graphics card is Geforce 6200 (should support the wanted resolution), and the monitor is connected with the VGA cable (if that matters).
View 7 Replies View RelatedI have connected my computer to my LCD-TV (HDMI-cable) to enjoy my movies and such, on a big screen. I have nVidia GeForce 7050 so in nvidia-settings I've been using the TwinView configuration which allows me to see both the monitor and the TV.
There was a bit of trouble-shooting but it worked just fine until yesterday when I changed my monitor to a new one and on the way probably messed up in nvidia-settings. I thought it would be easy to fix it but the configuration (in nvidia-settings) is stuck on "separete x-screen" and doesn't allow any changes at all. When I hit the "Detect display" nothing happens although I have the TV connected!
Maybe my xorg.config could tell somebody what is wrong. I've been messing around with the file and made lots of changes acc to different advices but I really don't understand the options and settings so I'm afraid I'll soon do something inreperable.
[Code]...
Yesterday I played a little with a Bitcoin miner and discovered today that I must have scambled my 3D settings. My Intel graphics card doesn't seem to work, instead I must have added a nVidia Settings Manager to my menu.
I already removed the package I mistakenly installed (something concerning OpenCL) but nothing happens. The xorg.conf file seems to be okay.
Gnome now only starts in 2D mode and Unity refuses to work at all. how I might get my Intel card back working?
I am new to Ubuntu (Karmic with GNOME). I have a Samsung LED UEB7020, with an Asrock ION 330 BD player feeding to a Onkyo TXSR607, AV rec. The other day I downloaded NVidia v180.25, which was very useful, because it immediately solved an earlier teething problem of no sound. However immediately upon re-booting and ever since, the screen size is too big for the TV, meaning that I can not see the top, bottom, side and left of the display by about 2 inches either way. I have checked the NVidia resolution settings and they are correct for the TV, ie 1920 by 1080.
My etc/X11/ xorg.conf file reads as follows:
Section "Screen"
Identifier "Default Screen"
DefaultDepth 24
EndSection
Section "Module"
Load "glx"
EndSection
Section "Device"
Identifier "Default Device"
Driver "nvidia"
Option "NoLogo" "True"
EndSection
in my media pc i have a geforce 8400, attached to a 32" 720p lcd using a dvi to vga adapter, and it is miss detecting the resolution it detects the resolution as 1080p, so when i try to enable full gpu scaling it gets the resolution wrong resulting no image on the screen. how do i manualy set the "back end resolution"
View 6 Replies View RelatedI had Ubuntu 10.04 running fine. Then I got curious about NVIDIA XServer.
"ATI Technologies Inc RV380 [Radeon X600 (PCIE)]" - Video Card
I opened it up, clicked a settings change, and said OK.
It said you need to update your blah blah blah.
Then it said blah blah blah doesn't exist.
Then it said it would create it for me.
Then I said REBOOT!
Now I get a black screen of death.
The only way I can get anything to happen on my monitor that comes from this computer is to boot into the Install Disk and say "TRY UBUNTU".
I have ubuntu 10.4 32 bit. I have 2x gtx 285's in sli that work perfectly fine in sli in windows (so its not a hardware not properly physically installed issue). But in ubuntu in the x server settings only one of the cards shows up. I was wondering if this is a 32 bit issue as in the past running 64 bit they have both shown up fine.
View 6 Replies View RelatedUbuntu 10.04, nVidia GeForce 9400, driver ver 195.36.15.When I log in, the system always comes up in 800x600 mode. I went into the NVIDIA X Server Settings page and changed it to my preferred setting of 1152x864. I hit Apply, then Save to X Configuration File (with correct root password).All is well until restarting. Then it reverts back. The update doesn't stick. How can I make this the permenant setting?
View 3 Replies View RelatedMy screen displays everything in a very wide but also very short way. When i click on (X Server Display Configuration) NVIDIA X Server Settings
I get this:
I run Ubuntu 9.04 on with proprietary NVidia driver 180.44.When I change anything in the nvidia-settings, e.g. screen resolution, brightness, second screen etc, everything works fine - except for the fact that I can't play any video files in any player. Sound is there, players don't display any error messages, but the image is black. Flash video within browsers is fine, though.Things go back to normal with the new settings kept after restarting X. However, having to restart X and lose my desktop set up every time when I just want to connect my laptop to my office screen is highly inconvenient.Is this a bug or expected behaviour that I have to live with?
View 3 Replies View RelatedI had some issues with nvidia drivers, and removed all of the packages using
Code: Select allrm /etc/X11/xorg.conf and Code: Select allapt-get purge nvidia*
Upon reboot, I was back with nouveau drivers and proceeded to reinstall nvidia drivers according to [URL] .....
Code: Select allapt-get install nvidia-driver
apt-get install nvidia-xconfig
I can then change my refresh rate using
Code: Select allnvidia-settings
but when I hit "Save to X configuration file", I get the following output in terminal:
Code: Select allroot@debian:/home/anon# nvidia-settings
Package xorg-server was not found in the pkg-config search path.
Perhaps you should add the directory containing `xorg-server.pc'
to the PKG_CONFIG_PATH environment variable
No package 'xorg-server' found
As a result, my nvidia preferences aren't saved across reboot.
Here are all of my sources:
Code: Select alldeb [arch=amd64,i386] http://repo.steampowered.com/steam/ precise steam
deb-src [arch=amd64,i386] http://repo.steampowered.com/steam/ precise steam
deb http://ftp.ca.debian.org/debian/ jessie non-free contrib main
deb-src http://ftp.ca.debian.org/debian/ jessie non-free contrib main
[Code] ....
System Specs:
Debian GNU/Linux 8 (jessie) 64-bit
Gnome Version 3.14.1
Processor: Intel® Core™ i7-4770K CPU @ 3.50GHz × 8
Graphics: GeForce GTX 780/PCIe/SSE2
using ubuntu 9.10 quick summary: need to set my tv resolution to 1840x1036 to see the whole desktop without cropping i just got a panasonic plasma tv and am trying to use it to watch movies from my computer. I hooked it up using my graphic card's dvi out. Since the TV came with a dvi to hdmi adapter I just had to buy a hdmi cable and now its set up to run under 1080p input. So I got 1920x1080 resolution for the tv. The problem is that the resolution does not fit exactly into the tv's screen. I am missing about 30 pixels top & bottom and some on the sides too. This results in me seeing my desktop on my tv, but the top panel with the applications menu etc is just out of bounds.
Under windows xp I have the same problem, but the nvidia control panel there has an option to "Adjust desktop size and position" which kind of works. Well you can resize but you cant position the picture. Resizing makes my actual resolution 1840x1036 pixels. With that resolution my left rigth top and bottom edges are all inside the TVs screen. Now i tried to do this in ubuntu using nvidia-settings and manually editing xorg.conf, but I am having no success at all. Nvidia or the x server or something is totally ignoring any modlines I include for my second screen (tv), and always shows 1920x1080 ... I have no way to scale the picture from the tv menu so I need to scale it in ubuntu. Does anyone know how to do this ?
Using online Debian guide, installed latest nvidia-current, glx etc which seems to be 195.xx Machine boots to GUI but monitor setting menu doesnt respond nor is there an nvidia specific one. xorg.conf shows 'nvidia' driver but I suspect I am still on 'nouveau' since the synapatic package manager doesn't show an nvidia xserver-xorg-video choice.
Second question, any trailheads for using wheezy based drivers (i.e. nvidia's latest 270.xx) with squeeze?
Currently I have two 1920x1080 screens running in Twinview on my Geforce 275 graphics card. Want I want to do is a quick simple way of disabling my secondary monitor when playing video games or using xbmc to watch movies, etc. I've tried a few applets but they require the xandr function which I think Nvidia doesn't support.
Is there a way to disable this quickly other than loading up nvidia-settings and disabling the monitor everytime. I don't really want to use two seperate x sessions and xinerama due to the fact you can't use compositing.
I am using an Abit NF7-S V2 mobo to set up my dual boot system where each OS (XP & Ubuntu) will run on a totally separate HD (as opposed to both OS�s being set up on one HD). Since they will be running as stand alone boot drives, how does one set it all up so that one can boot from one or the other? I don�t see how I can do it from the bios. How do I do it?
View 2 Replies View RelatedNot sure if this is the right forum for Linux Mint but I heard it is based on Ubuntu so I figured it might be ok. Let me know if I'm wrong. I'm having trouble getting the X server settings to stay when using the Nvidia X configuration tool on Linux Mint 9.10. Everytime I try to save to xorg.conf it gives me "Failed to parse existing X config file '/etc/X11/xorg.conf'!" even when using the sudo command.
View 1 Replies View RelatedI need a seperate workspace on each monitor and I use nvidia propriatary graphics drivers (I have a Geforce 9500 GT Graphics Card. It has one dvi port and one vga using both for my monitors.) The only problem is whenever I try to save the settings I apply something like twinview or the seperate x workspaces with the second monitor enabled It applys it but this is what happens in sequence (It may be only twinview that does this but i'm not sure not at my home computer right now):
1.) Picture cuts out to a blank screen on main monitor
2.) Pictures turns on in the second monitor (Its a seperate workspace from the main monitor)
3.) 3 to 5 seconds later the picute cuts out to the second monitor
4.) I'm left with two blank screen monitors and no way to turn the GUI back on other than a complete restart of the computer.
I need help on both of these issues. If it helps any one monitor is a CRT (The one on the right) and the one on the left is an LCD (The LCD is the main one). I also have Ubuntu 9.10 32 bit Karmic Koala if that helps. Lastly I have the latest propriatary graphics driver from nvidia (185 I think.) I also installed the driver from nvidia via Jockey (I think thats the name of the default driver installer for ubuntu..?) That is my situation and as you can tell its a pretty complicated one.
I am trying to set up a video streaming server on my Gnu/Linux Ubuntu 10.10. I want to be able to stream videos that I have on my computer to my friends who aren't on my network.streaming audio applications but that won't help me. Most of the tools available are only for sharing within your own network.
View 1 Replies View RelatedHow would I go about manually making the IP V4 settings? I can view these in System >> administration >> network settings. But there is no way to edit it :S
View 4 Replies View Related
