Not sure if this is the right forum for Linux Mint but I heard it is based on Ubuntu so I figured it might be ok. Let me know if I'm wrong. I'm having trouble getting the X server settings to stay when using the Nvidia X configuration tool on Linux Mint 9.10. Everytime I try to save to xorg.conf it gives me "Failed to parse existing X config file '/etc/X11/xorg.conf'!" even when using the sudo command.
View 1 RepliesI am using Fedora 13 x86_64 on a Acer Aspire 7730ZG laptop with: 01:00.0 VGA compatible controller: nVidia Corporation G98 [GeForce 9300M GS] (rev a1) I have kmod-nvidia-2.6.33.6-147.2.4.fc13.x86_64-195.36.31-1.fc13.2.x86_64 installed from rpmfuison when I plug in the hdmi cable to the tv, my tv says the resoultion is at 720p, and I can not get any of the resolutions settings to look right on seperate x screen with the nvidia X server settings gui. my tv is a vizo 42inch. also another question is their a way to set the video card to output at 1080? this might be part of my problem?
View 14 Replies View RelatedHow do I do this? You do not appear to be using the NVIDIA X driver. Please edit your X configuration file (just run `nvidia-xconfig` as root), and restart the X server.
View 3 Replies View RelatedI plugged the usual 4-pin s-video cable into my TV and graphics card. I went to nvidia x server settings, nothing. I hit detect monitors, nothing. I changed the TV to the proper input channel, Nothing. It's a bit annoying,I used it with the old GeForce Ti4200.
View 1 Replies View RelatedI have 2 monitors, a 22 inch samsung as my main and an acer as my alt. I am trying to get the samsung monitor to display, but is is disabled. So I enable it as a separate x display, then save, but when I restart x, the settings didn't save. I save the config under under /etc/X11/xorg.conf. What am I doing wrong?
View 4 Replies View RelatedI have ubuntu 10.4 32 bit. I have 2x gtx 285's in sli that work perfectly fine in sli in windows (so its not a hardware not properly physically installed issue). But in ubuntu in the x server settings only one of the cards shows up. I was wondering if this is a 32 bit issue as in the past running 64 bit they have both shown up fine.
View 6 Replies View RelatedI have a Dell E6500 laptop (1280x800 screen), which I frequently dock.The dock as two Dell 1908FP 20" monitors connected by DVI. I can move between the laptop display and the twins by manually changing display configuration in NVIDIA X Server settings, but this is a pain requiring about 15 clicks each time.
I have tried using the "Save to X Configuration File" option in the Nvidia server settings, but this seems to screw everything up. I need to dynamically change between the setups... anyone have advice on getting that done?Can the xorg.conf file be configured to do it?My xorg.conf looks like this:
Section "Screen"
Identifier"Default Screen"
DefaultDepth24[code]......
Using online Debian guide, installed latest nvidia-current, glx etc which seems to be 195.xx Machine boots to GUI but monitor setting menu doesnt respond nor is there an nvidia specific one. xorg.conf shows 'nvidia' driver but I suspect I am still on 'nouveau' since the synapatic package manager doesn't show an nvidia xserver-xorg-video choice.
Second question, any trailheads for using wheezy based drivers (i.e. nvidia's latest 270.xx) with squeeze?
I'm about to ditch Freenas as my NAS software and make it an Ubuntu server box. The mainboard is an Asus AT3ION-T dual core Atom board. Freenas runs happily from USB stick. I have no optical device to install Ubuntu from and would like to install Ubuntu Server to a USB stick.
View 8 Replies View RelatedIn nvidia-settings I see, alongwith Disabled and TwinView settings, "Separate X Server". I tried choosing the option for my LCD (connected via HDMI), but I get a blank screen, presumably since the LCD's X server has nothing to render.
How do I direct any application (say vlc) to use that X Server instead of the Monitor's X server?
I've been trying without success for the past couple of weeks to setup a filtering system for my little sister's netbook. The main problem I've been running into is inconsistency. First, I tried using dyndns per the instructions here: [URL] The problem with this is the DNS settings (and in turn the filtering settings) dont appear to 'stick' once the Netbook touches a different network. So if I sign onto a different wireless network than the one I used to set up the filtering, it stops working. The reason why is Ubuntu will overwrite the current DNS settings with those of the new network (I have no idea why, and am too frustrated to figure out).
Also, I noticed that even if the settings did stick, they're fairly easy to disable because all she has to do is stumble across the DNS settings, change them back and voila. I've had great success with OpenDNS on Windows boxes, but there doesn't seem a to be a feasible way to apply it to Ubuntu. Dansguardian looks like it may be worth a shot, but I've seen dozens of "simple" configuration guides, none of which that actually looked simple. So my question is this, what is the easiest, most bulletproof way to setup web filtering 10.4? Preferably something that a 12 year-old could easier find her way around.
I recently switched back to Debian after getting fed up with Ubuntu. The one feature that I haven't been able to get back since the switch is Wake on LAN.If I turn on the computer and watch tcpdump, I can see the packets hitting my machine. I don't think it's a router configuration issue.If I shut down from windows, WOL works.Another sign that it's not a networking or BIOS thing.Here's some stuff I've tried:When I boot up in linux, if I run ethtool eth0, it tells me that wake is set to g (which every guide I've read says is correct).Just in case, I added "post-up /usr/sbin/ethtool -s $IFACE wol g" to /etc/network/interfaces (as shown here: ewtopic.php?f=5&t=42049&p=244736&hilit=wakeonlan#p244736). Also added same thing for post-down.
In /etc/init.d/halt, I changed NETDOWN to no (also from previous guide) to keep my eth card from being shut down.Also changed /etc/init.d/networking to exclude eth0 (as documented in Added "pre-down false" to /etc/network/interfaces.. trepid+wol), to keep eth0 from being shut off.Anyway, I'm guessing that either there's another script somewhere shutting off eth0 or I'm completely wrong in assuming that's the problem. I've been googling this problem for a couple weeks now and I'm totally out of ideas.
I'm running openSUSE 11.3 64 bit KDE 4 standardI have two monitors attached, running simultaneously, nicely, all is well.But when I reboot I have to set them up again because the settings don't stick/endure through a reboot.The GUI configurator that I use is at Menu --> Config Desktop --> General --> Display.How do I save the underlying settings and re-invoke them at boot time, perhaps from the CLI? Or some quick process that will do the job.
View 8 Replies View RelatedI have no clue why KDE is doing this, but whenever I reboot the system, the resolution resets to 1024x768. I really need to stop it from doing this. Also, Sax2 doesn't seem to be working and there is no xorg.conf file that I can see of.
View 4 Replies View RelatedStill pretty new to this, from what i have read, the more info i give the better, I am running ubuntu 11.04 with KDE installed via the terminal. I was trying to get my TV to work as another display, I don't know what I have done, after my earlier problems I have learnt to back up and restore my xorg.conf file but with no luck, I now can't change any settings as the title says the apply button is grayed out and when i try and save it to the xorg.conf file and restart the xserver it says that "Your current changes to the X server display configuration may no longer be applied due to changes made to the running X server.
You may either reload the current X server settings and lose any configuration setup in this page, or select "Cancel" and save your changes to the X configuration file (requires restarting X to take effect.)
If you select "Cancel", you will only be allowed to apply settings once you have reset the configuration.Your current changes to the X server display configuration may no longer be applied due to changes made to the running X server. You may either reload the current X server settings and lose any configuration setup in this page, or select "Cancel" and save your changes to the X configuration file (requires restarting X to take effect.)
If you select "Cancel", you will only be allowed to apply settings once you have reset the configuration. Your current changes to the X server display configuration may no longer be applied due to changes made to the running X server. You may either reload the current X server settings and lose any configuration setup in this page, or select "Cancel" and save your changes to the X configuration file (requires restarting X to take effect.)
If you select "Cancel", you will only be allowed to apply settings once you have reset the configuration."
when I booted last i got terminal with this showing, for the first time,
Xlib: extension "RANDR" missing on display ":0".
(orca:1984): Wnck-WARNING **: Property _NET_WM_NAME contained invalid UTF-8
My xorg.conf is
# nvidia-settings: X configuration file generated by nvidia-settings
# nvidia-settings: version 270.29 (buildd@roseapple) Fri Feb 25 14:43:24 UTC 2011
Section "ServerLayout"
[Code]...
Ubuntu 10.04, nVidia GeForce 9400, driver ver 195.36.15.When I log in, the system always comes up in 800x600 mode. I went into the NVIDIA X Server Settings page and changed it to my preferred setting of 1152x864. I hit Apply, then Save to X Configuration File (with correct root password).All is well until restarting. Then it reverts back. The update doesn't stick. How can I make this the permenant setting?
View 3 Replies View RelatedFor some reason the nvidia-settings configuration utility entry vanished from the menu after an update, the problem happened again after a recovery via a clonezilla hdd image also after an update, has anyone got any idea's as to recover the entry and how to stop this issue arising in the future?
View 4 Replies View RelatedI recently installed Ubuntu, 10.4
My problem is that when i log in, the resolution isnt what i want. So i change it via the Nvidia x server settings, and press Save to x config file
Yet when i log in again, it defaults back to what it was before i changed it?
Iv looked all over the internet for the past 2 days and nothing seems to work.
I'm running dual-screen. On 24" at 1920x1080 and one 19" at 1440x900. After installing Mint 9 I can't set the resolution any higher than 640x480 in nvidia-settings. I've installed the "recommended" nvidia-driver that Mint suggests.
[Code]...
What could be the problem? Why can't I set the res higher than 640 in nvidia-settings? Everything worked in Mint 8 (10.04). During installation the res was higher than 640.
I believe the Nvidia drivers were installed by default.. as I run the command:
I get:
However, when I do nvidia-settings, I get "command not found".
How do I see if the proprietary Nvidia drivers are installed?
Also, with GNome (on Ubuntu for sure), I can see a GUI tool to configure my NVidia settings.. how do I access this tool with KDE?
After installing some (much needed) upgrades, I am stuck being unable to install nvidia-settings after screen-resolution-extra upgraded from .11 to .13. Nvidia-settings, supposedly, requires .11. I can, of course, downgrade to .11, but I do not know if this is recommended. Is there anyway to get nvidia-settings back without downgrading? What is a good course of action?
View 1 Replies View Relatedafter many a tear I just by sheer chance found out that, when logging in to my gnome-session (or any session really) from kdm I can do something that has eluded me for quite a while now: change screen-configuration between 1 screen and 2 screens as I please without having to log out, shutdown x, copy xorg.conf I need, restart x, log back in.
So question is: what could it possibly be, that makes GDM break a feature like this for the nvidia-settings dialog? Can anyone confirm this? *wants that error and shoot it in the face... er... code!* I still don't feel like reinstalling the whole thing, just to find out if this is due to this system being... well... OLD. Also call me a bit oldschool, but reinstalling is just lame.
*edit* me dumbass:
NVIDIA-Linux-x86-260.19.12.run
2.6.35-23-generic-pae
maverick
I just bought a new 24inch monitor that supports the resolution 1920x1200. Unfortunately, the nvidia-settings dialog does not have this resolution as an option (currently running on 1920x1080). The graphics card is Geforce 6200 (should support the wanted resolution), and the monitor is connected with the VGA cable (if that matters).
View 7 Replies View RelatedI currently have a problem with my nvidia settings
I reinstalled 11.04 kubuntu recently and I no longer could use my second screen.
I looked into my nvidia settings and enabled my second screen (separate x screen).
However when I do so and press apply the second screen does nothing.
This is two desktop monitors and not a laptop and a monitor.
I'm wanting to use some Emerald themes. I start the compiz icon and do the settings then when i restart the settings don't stick. Does anyone know how to make them permanent?
View 5 Replies View RelatedI have connected my computer to my LCD-TV (HDMI-cable) to enjoy my movies and such, on a big screen. I have nVidia GeForce 7050 so in nvidia-settings I've been using the TwinView configuration which allows me to see both the monitor and the TV.
There was a bit of trouble-shooting but it worked just fine until yesterday when I changed my monitor to a new one and on the way probably messed up in nvidia-settings. I thought it would be easy to fix it but the configuration (in nvidia-settings) is stuck on "separete x-screen" and doesn't allow any changes at all. When I hit the "Detect display" nothing happens although I have the TV connected!
Maybe my xorg.config could tell somebody what is wrong. I've been messing around with the file and made lots of changes acc to different advices but I really don't understand the options and settings so I'm afraid I'll soon do something inreperable.
[Code]...
I'm trying to set graphical settings like AA, AF and Vsync in Nvidia-settings however they don't stick, all I get is a error like this code...
and I have to manually reset them to desired values after every login. Is there a way to make them stick when logging in/out?
Yesterday I played a little with a Bitcoin miner and discovered today that I must have scambled my 3D settings. My Intel graphics card doesn't seem to work, instead I must have added a nVidia Settings Manager to my menu.
I already removed the package I mistakenly installed (something concerning OpenCL) but nothing happens. The xorg.conf file seems to be okay.
Gnome now only starts in 2D mode and Unity refuses to work at all. how I might get my Intel card back working?
I frequently move my computer between rooms. Instead of opening the nvidia-settings, making the changes, applying, then confirming them is there an easier way using shortcut keys or shortcuts? Would like to have Ctrl-1 as change to laptop display only, Ctrl-2 for external only, Ctrl-3 for Twinview
View 1 Replies View RelatedI'm on a 64-bit machine running Debian 8.2 "Jessie" with MATE Desktop Environment.
I have a Geforce GTX 650ti video card.
I'm logged in as a non-superuser account named "john."
I open NVIDIA X Server Settings GUI, change my monitors' brightness from 0.000 to -0.1, go to the "nvidia-settings Configuration" section, click "Save Current Configuration" and click "Quit."
But when I reboot, the brightness is back at 0.000.
[URL] .....