Ubuntu Installation :: New Install, Poor Display And No Wireless?
Apr 9, 2011
I'm almost a complete noob when it comes to Linux. All my computers 'til now have been Windows boxes (3.1 on up to XP). I do know a little, I've tried to switch to Linux since RedHat 7.2 but never got this far (I can connect to the Internet!). I currently have two issues I really need to get past this weekend, or I'll be forced to spend $110 on Windows 7 - which I REALLY don't want to do. I can't get the display right, and I can't get the wireless working.
My computer is an AMD Zacate on an ASUS motherboard with integrated graphics (ATI Raedon 6380, if I remember correctly from this afternoon). I'm using an Insignia 1080p TV as my sole monitor. The wireless card is a Zonet ZEW1642S which uses the Ralink RT3062 chipset. Today I finally got the monitor to display in 1920x1080. I updated the ATI drivers (HDMI sound started working after I installed them) and downloaded Catalyst. I've been trying to get through the xrandr instructions to get the screen to fit, as I can't see the top and bottom bars. Also, I think it's displaying in 1080i instead of 1080p. Text quality is atrocious compared to the 1024x768 resolution it had earlier. The screen refresh is terrible.
I opened terminal, inputted "xrandr" and got:
Code:
Screen 0: minimum 320 x 200, current 1920 x 1080, maximum 1920 x 1920
DFP1 connected 1920x1080+0+0 (normal left inverted right x axis y axis) 698mm x 392mm
1920x1080 30.0*+ 30.0
1776x1000 30.0
1680x1050 30.0 30.0
I installed openSuSE 11.2 sometime ago in a COMPAQ Presario CQ60-419WM laptop (the ones that Wal-mart sold for $300 about a year-and-a-half ago. I installed the 64-bit version because I saw that the processor could support that (perhaps that was not a good idea). I have some problems that seem related to not having the necessary drivers. My wireless has never worked and my display is far from what I would like it to be (the response is slow, if a drag a window, its motion is jerky, if I scroll down in a browser window, the motion is wavy). The look and feel is very different from what I get at work and I do not know how to fix it.
I asked this question in the installation forum and got as far as possible with the advice there. I'm using a 32" Insignia TV as my sole monitor. I'm using the HDMI from the integrated video on my ASUS E35M1-M motherboard. I have it running at 1920x1080. When it boots up the monitor says the BIOS is running at 1080p, but as soon as Ubuntu loads the TV switches to 1080i. When I was setting the computer up the other day it was running 1024x768 and the text looked beautiful, now similar size text is blue/black and scraggly/shadowy looking. I followed some instructions for xrandr, but ran into problems and the person giving me advice admitted he was too unfamiliar with xrandr to get me any further. Here's as far as I get:
I am running karmic and have wireless performance which is terrible on the EEE 1000HA I see it as low as 1mbit at times and others at 24mbit and briefly at 48 and 54mbits. running an Internet speed test with wireless I get pathetic speeds as low as 15Kbps, Its 5 feet from the wireless router ... and other machines that are wireless in the same area show 54mbits and perform great ... any one solve this problem with the asus EEE1000HA running on karmic?
iwconfig shows that the bit rate is 130Mb/s and link quality is 98/100. I'm using the wcid network manager instead of defaul gnome one. I'm getting lots of packet loss and performance is very bad. The connection is practically unusable. I've tried installing the compat wireless backport package but that did not work at all.
My wireless is flakey -- dropped connections, poor speed, etc. As diagnosis, I loaded the 'wavemon' utility so that I might watch the radio and signal and noise.Things will be good, then fall off, then get better, then go away entirely. Repeat continuously and randomly. For these experiments, my laptops -- more than one -- are on a table.The table is roughly 15-20 ft laterally from the access point. The access point is also 8 ft above the floor vs. 3 ft table height.(grin) While the signal "wobbles" everything else is mechanically stable and otherwise not moving.
My mother has Windows Vista and i have linux ubuntu. She has a special verizon card that she inserts into her laptop for internet. My computer also has an internal wireless card, but the signal here is very poor. Supposedly, among windows computers, I would be able to get a flashdrive, and with a little program uploaded from my moms computer, set things up using the flashdrive on my computer to share the internet that she pays good money for =/ However, it wont work with ubuntu, which isnt in the windows inner circle. When I open the executable file with WINE it says that it cant run wireless network setup "on this version of windows". lawl. I was wondering, is there any way around that? Is there anyway to network with my mothers internet?
I installed Ubuntu 10.04 on an 8GB flash drive, and through much effort, was able to boot it on my white MacBook (2Ghz Core 2 Duo, 2GB RAM). I find that responsiveness is really poor, for example, the display frequently freezes when I switch windows, or load a web page. Is this expected for Ubuntu that's running from a flash drive? Are there ways to improve this?
I've installed Fedora 12, with the "basic video option." I've also installed an ATI driver via -- sh ./ati-driver-installer-9-12-x86.x86_64.run. However, in spite of installing the ATI driver, the resolution is poor. Rather than using the entire screen, only a reduced portion is visible/used. How to resolve this, so I can use the entire screen?
I am trying to do a clean install of UBUNTU 9,10 onto a machine that had been running 7.04 successfully for some time. It is a Pentium 2.8GHz processor with geForce 6200 video card.
I boot the system using the install disk, and get past the point where it asks for the language selection. At that time the display shows vertical bars that flash alternating colours. The screen does not recover from this state. I have also attempted to install 9.04 on the same machine, but the same thing happens.
I installed 9.10 on another machine with similar hardware configuration using same disk without problems (without a doubt the best operating system I've ever used!)
I am completely new to the world of all things linux. I have recently needed to build a linux server to host a Google box, so we decided to use old kit firstly a Dell 1400sc and a Dell poweredge 650. In both cases after the install we got a massage saying that it could not display output the lcd monitor.
I have searched on the web to resolve the issue, and some of the resolutions said to amend the something in the grub. However I have not been able to enter the Grub menu even after trying esc or shift.
Lucid installed without any errors that I can see of off the main i386 installation CD, but after booting I get no display. Even in recovery mode. The monitor doesn't go into sleep mode and I can tell that the OS is actually running the background because I can do a Ctrl-Alt-Del and do a proper shutdown. I'm running an nvidia GT 9500. Everything is working fine on Karmic.
I have this problem where the 10.10 LiveCD 64-bit works (as in I get full resolution display and no video issues at all). But after install, the OS boots successfully but there's no display. I know it's successful because I was able to login in the dark (sound works).
Here's what I have: HP m9340f (NVIDIA GeForce 9500M GS with HDMI) 46" Sharp connected via HDMI Windows 7, works fine.
Here's what I tried with no luck: 1. CTRL-ALT-F1 still doesn't show anything on screen, no terminal 2. Connected via VGA 3. Connected another 17" monitor via VGA, rebooted 4. Added vga=789 in grub before booting
The weird thing is that I had 10.04 before and it was working for a while then it suddenly stopped working. I figured I'd wait until 10.10 but I now have the same issue. I haven't tried 32-bit... I can give that a shot in a bit.
I did a LiveCD to USB install, following the directions I found at [url] When I went to reboot to the USB stick, all I get is a black Screen (monitor is on and lit, just nothing on the display) No cursor or command prompt. I've tried holding shift to bring up the GRUB menu, changing splash quiet to nomodeset, or just adding nomodeset after the splash quiet thing. I've even tried xforcevesa instead of nomodeset still black screen. Looking at the logs nothing is current as of the last time I tried to boot the computer, it's strictly what was written when I installed it to the stick. Other things I've checked/tried, Pressing CTRL+Alt+F1 at GRUB to get TTY, all I get is that blank screen. I've Checked etc/default/grub to ensure the timeout was higher then 0. The Install CD seems to be OK but I have (as it did another install successfully) but I haven't done any throughal checking of it (there was no check this disk on the first screen of the LiveCD) The USB sticks also seem to be ok (in windows though). Using the disk utility on the live CD I did check the file system on the USB stick, the "/" partition came up clean. Anybody have any other thoughts on this install, any thing else I can check?
I am trying to install DDD on ubuntu 10.4. Downloaded the tar.gz file and followed the instructions given on DDD web page.But I am not able to install DDD. While trying to do './configure && make' I get the following error. It says c++ is not working and is not able to create executables. I have g++ installed and I successfully create excutables from .cpp files. I've also checked the CXX variable and it is set to /usr/bin where g++ is expected to be placed.
root@tirth-laptop:/home/tirth/Downloads/ddd-3.2.1# ./configure && make loading cache ./config.cache checking host system type... i686-pc-linux-gnu
I tried in November last year to install 11.2 on a machine with NSRock K8NF6P motherboard which has an onboard GEForce class 6 graphics card. Installation went ok until the very end. Then driver problem surfaced, display went blank and was then damaged and required repair.
The NVIDEA driver install appears to require the system is up and running before it is installed. As I did not get a running system how do I install the drivers before any damage is caused?
After the "Welcome to Fedora 12!" screen, I then click on either: Install or upgrade an existing system [or] Install system with basic video driver [both display the same following screen and then the machine halt on] Loading vmlinuz . Loading initrd.img . .ready. Probing EDD (edd=off to disable) ... ok The number and cap lock have no responses. When I changed to another display card, it has no problem at all.
The last version a Linux I had was Mandrake v9.1. However, in looking to get the latest/greatest Linux I downloaded Ubuntu and Kubuntu. After installing Kubuntu the system reboots and fails to boot into the OS. After the P.O.S.T all I get a the word "GRUB". There is no response to any keys with the exception of Ctrl-Alt-Del. I am temporarily able to get passed the boot problem if I boot from the CD and choose boot from primary hard menu option. I'm not sure how to fix the boot up problem and could use some advice. However, using the CD to boot up the hard drives installation leads me to my next problem.
While in a desktop session I am unable to drag windows by their title bar. When attempting to drag a window, the desktop becomes covered with parts of the original window spreading all over the screen in multiple directions. It looks like a kaleidoscope or bad acid trip image. I suspect the video anomalies might be configuration related or improper driver. Again guidance would be greatly appreciated here.
I have a good 'ole Matrox MGA Millenium card installed into a P4 1.8ghz system, with 512 MB ram. The hard drive originally had an old install of Mandrake v9.1, but all of the partitions were wiped and I created 3 new partitions:
- /dev/sda1 20GB Bootable/Primary Partition EXT4 (Unbuntu mounted at /) - /dev/sda2 18GB Primary EXT4 (Kubuntu mounted at /mnt/Ubuntu_dsktop_91) - /dev/sda3 2GB Swap space
My intent was to install Ubuntu on the 2nd primary partition and be able to switch between them. However, I tried installed Ubuntu on the first partition (reformatted of course) and I encounter the same boot problem and display problem.
Just installed 11.04. Before install, during live cd preview, it detected my dell wireless card and offered to install a Broadcom (as I remember) proprietary driver. However, after a proper install, it did not make the same offer and left no wireless available.
My only unhappiness with 11.04, after I installed in on 4/28 on my Eee PC 1000H (dual booting with Windows XP), is that the range of wireless reception in my house, from exactly the same spot as before, has worsened considerably. No problem when running Windows (which I'd rather not do, of course). Could the upgrade have installed a new driver for the wireless hardware that isn't as good as the previous one?
I just got my self a netbook. I bought the one with linux because I figured that if they sell it with linux, it's probably using h/w which supports linux. I played around with the Mi variant it had pre-installed, but it was a bit limited and slow, so I installed UNR instead.The install went fine, and UNR is really nice to use and feels faster than the Mi too which is great. However, wireless isn't working. It's got a broadcom chipset (BCM4312) which I think needs a proprietary driver, but when I use the Hardware drivers tool, it doesn't have any options to install a driver.
I've done a ton of searching and all I've found seems geared to having your printer/scanner connected via USB cable in order to get the scanner working. I have the printer working wirelessly but thus far no go on the scanner. I've downloaded and installed the scangearmp packages.
I've tried installing the sane package via git according to this blog but when I try to run configure I see this: mustek_usb2 backend requires pthread library - disabling and usb isn't listed among the installed backends. I don't even know whether I need usb because this is wireless, but after compiling I run scanimage -L and nothing comes up. I'm still a Linux newb, and have learned a ton in the past couple of days, but this one is stumping me.
I did a command-line installation. I dont have an ethernet connection, only wireless. For some reason the alternate installer doesnt install "wireless-tools" How do i install it? At this point I am thinking of booting off a live USB, downloading the wireless-tolls package from here Save it to a folder in the command line installation where?) then boot back into command line and install from there But I am not that savvy with command lines, and dont know where to install to...
I have FC4 installed on my system and my internet connection is a ADSL through a Router but i have a wireless isdn line as backup connection the modem i use is LG LSP 340E which is a limited mobility cdma phone with in built modem, the supplier and manufacturer has given drivers for windows only. How to install this modem onto my system, I had tried auto detection but it didn't work, I had connected the modem to the serial port in my system.
I have installed Fedora 8 on my laptop. My laptop has a " Network controller: Broadcom Corporation BCM94311MCG wlan mini-PCI " wireless Card. I want to get the wireless working. I did an 'lsmod' and I found that the modules for this card is not installed. I tried to start Network Manager, but network manager cannot connect to wireless but it cant. How and where can I get the drivers for this and how do I install those modules. My laptop is a Dell vostro 1400.
