Lucid installed without any errors that I can see of off the main i386 installation CD, but after booting I get no display. Even in recovery mode. The monitor doesn't go into sleep mode and I can tell that the OS is actually running the background because I can do a Ctrl-Alt-Del and do a proper shutdown. I'm running an nvidia GT 9500. Everything is working fine on Karmic.
View 4 RepliesI can't figure out how to install the nvidia drivers for my nvidia 8800 GT video card. I've followed some other posts and all the posts seemed either incomplete, or led me down a path of which eventually broke my installation, that I needed to reinstall the entire ubuntu system.Again, it may not have been broken, i just didnt know how to get back in to the gui version of ubuntu, the instructions took me to the console terminal
1.) I've installed the ubuntu 10.10 64bit for i386 in an oracle virtualBox..
2.) downloaded from nvidia.com "NVIDIA-Linux-x86_64-260.19.44.run"
3.) Stuck don't know what to do.
I just installed 10.04 Lucid Lynx and have a serious graphics problem. I've attached a picture to show the problem.
Some Background:
Pentium 4 3.06GHz
1.5GB RAM
ATI Radeon 9600
I installed via liveUSB but had to choose the "nomodeset" option by pressing F6. Otherwise after the Ubuntu boot screen the graphics went like that in the attached image. The installation went fine (took less than 15 minutes!) but after the reboot the graphics problem returned. I can't see anything and the system is useless this way. I can't post up any logs (I'm typing this from the liveUSB).
I have a Zotac IONITX-F-E motherboard (Intel Atom Dual Core 1.6 GHz + Nvidia ION) -based box with Ubuntu 10.04 64-bit installed. Do you or does someone you know have the same setup as I do? If so, do they have 1080p video playback working? If so, what driver are they using? I've tried following every guide I could find, but no luck so far. I have libvdpau1 and libvdpau-dev installed. I have the nvidia 195.36.24 driver installed (I used the nvidia installer). I have mplayer installed (which I compiled from source with --enable-vdpau).
I try to run mplayer with this command:
Code:
mplayer -vo vdpau -vc ffh264vdpau path/to/myfile.mkv
I get the following message in my terminal:
Code:
Error opening/initializing the selected video_out (-vo) device.
I have libvdpau-dev and libvdpau1 installed.
After Googling this problem, I found a post that suggested the following steps:
Code:
sudo add-apt-repository ppa:nvidia-vdpau
sudo apt-get update
sudo apt-get install nvidia-glx-195 nvidia-195-modaliases
It turns out that I had already added the nvidia-vdpau repository. However, despite that, I get:
Code:
E: Couldn't find package nvidia-glx-195
The same problem exists for the nvidia-195-modaliases package. Do these packages exist? Is there some other way to get them?
how do you install an nVidia video driver?
View 1 Replies View RelatedThe nouveau driver coming with the free fedora does not even allow to run Gnome 3, so I'd like to install the Nvidia driver. So far I did not succeed as the nouveau kernel module is loaded at an early stage. How can I remove the nouveau driver?
View 6 Replies View RelatedUsing the video card Nvidia 7800GT on an AMD4200, MB T6100, I am unable to install from the iso, as progression is halted by a video mode that is unviewable. (black and white rows). I can get to the "f6" menu, however once I attempt an install it fails. My main goal is to install Mythbuntu, however the problem seems to be with the Unbuntu install drivers.This post worked to get around this on version 6.10, however these instructions no longer work. http://ubuntuforums.org/showthread.php?t=379807
Is there any way to use the newest Nvidia drivers that should work from a new install CD? I do not see a command line option, which would seem to allow me to install and update and setup the distro, THEN add my drivers before I run xconf.
I went back to Suse 11.2, it comes with the 'nv' driver for my NVIDIA Quadro2 Pro (64 MB) and I'm getting some slow performance on browser display and sometimes video playing. Not always, I recently saw a 2 hr long movie on Blue Ray resolution, so the problem is not hardware, it's software. I saw several links here on how to install other drivers and a 1-click install link on this page but my question is, since this is an old card... which driver is the best for this card ?
View 9 Replies View RelatedDo you think if I do an upgrade from 9.1 to 10.04 and then add i915.modeset=0 ( works with the live CD) to the boot sequence and then load the proprietary NVidia drivers from sys/admin/hardware drivers, that I'll get full screen resolution.
BTW if I don't use the modeset=0 I get a blank screen after update reboot.
I have a Nvidia 7600GT dual head video card. I enabled the restricted drivers and I have even installed the latest drivers from the Nvidia web page. I am stuck with one display running at 640 X 480.
View 4 Replies View RelatedI attempted to install nvidia-current 195.36.24 from Synaptic for an Nvidia GTX 460. It didn't appear to work and I want to fully un-install all Nvidia drivers and do the 'official' (convoluted) Nvidia procedure of logging out of x etc: - [URL] The issue is; I tried to remove via Synaptic, but when I restart the system I get an error stating: - 'Ubuntu is running in low-graphics mode. The following error was encountered. You may need to update you configuration to solve this. (EE) Failed to load module "NVidia" (module does not exist, 0) (EE) No drivers available.
This is actually the error that kept appearing and made me want to remove everything. My question is: - Can I just go ahead and install the 'official' Nvidia driver, even though the 'startup' appears to be getting some kind of reference from somewhere? I understand that I'll have to remove the Nouveau driver as well some how. . .
I've been running Lucid since it dropped. Decided to upgrade my NVIDIA 6600gt graphics card to the newest driver I found at the website. Installation went flawless. But after reboot, I got this:
Ubuntu is running in low-graphics mode
The following error was encountered. You may need to update your configuration to solve this.
(EE) May 05 12:24:17 NVIDIA(0): Failed to initialize the NVIDIA
kernel module. Please see the
(EE) May 05 12:24:17 NVIDiA(0): system's kernel log for
[Code]....
I want to use my video card, but after upgrade i got this message:
You do not appear to be using the NVIDIA X driver. Please edit your X configuration file (just run `nvidia-xconfig` as root), and restart the X server.
will be apreciaTED, after running from terminal I got this
CODE:
rey@rey-desktop:~$ sudo nvidia-xconfig
[sudo] password for rey:
Using X configuration file: "/etc/X11/xorg.conf".
Backed up file '/etc/X11/xorg.conf' as '/etc/X11/xorg.conf.backup'
New X configuration file written to '/etc/X11/xorg.conf'
Had mythbuntu/xbmc running for 4 months with vdpau and all the same hardware. I killed it with an update and thought it'd all be easier To build it the 2nd time -- wrong! Fresh install of mythbuntu lucid off cd, Asus p5g43t-m pro, nvidia gforce 9500 gt
What I tried so far...Different drivers with the hardware app thingee. Multiple times -- Purge nvidia, purge nouveau, blacklist list of other video stuff with extra line after, stop gnome, manual install various drivers - 195.xxxxx or Synaptic install various drivers. Tried updates, adding avenard and daily build repos. Everything in combinations. Outcome remains consistant. Lo res error start, can't load nvidia driver, selected but not in use, xorg.conf needs editing.
I'm getting the same error messages as the common nvidia help posts describe but the solutions aren't working for me.
4 days of this, 3 installs plus a shot at Mint, and no progress. I'm pretty frustrated. I'd consider returning to karmic if I didn't think the updates would pork the nvidia driver all over again.
Last install of 9.10 there was a required edit of vmalloc=256M and a shut off of cx18. That's been fixed in lucid? What else ccould it be?
This morning, I authorized an update as almost every day. I saw that the nvidia driver was on the list but in recent years, I no longer fear these driver updates since everything usually works well...
Except that this time, no! I turn on my pc this afternoon and more 3d effects. I run "Nvidia X Server Settings" which tells me I do not use the nvidia driver and must run as root the command "nvidia-xconfig," what I do. I restart X and no display at all, only the prompt in text mode!
I just installed Ubuntu last night parallel to windows vista ultimate (no problems). My biggest problem is that when I tried to install the nvidia display drivers, I somehow downloaded a server based driver (and am having amazingly difficult problems). I use a dual monitor set up (both are plug and play LCD displays) and i'm not too worried about aesthetics but rather, performance. I downloaded the correct driver but now I don't know how to install it. Is there a way to uninstall this server driver?
View 1 Replies View RelatedI just installed 11.04 and I knew I would have to install the NVidia video drivers. So it was no surprise when it popped up a warning and dropped me into Gnome Classic view. So I turned on the NVidia drivers and rebooted. In my desktop selection menu on the login screen I have "Ubuntu" and "Ubuntu Classic".
Unfortunately they look exactly alike, with the Gnome panel along the top, and the panel with the taskbar, desktops and recylce bin on the bottom. I've gone back-and-forth a few times and nothing has changed. Some changes in one environment is not set in the other, like they really are 2 different environments.
According to the Software Center, Unity (not Unity 2D) *is* installed.So how can I boot into the Unity desktop?
I have no display after attempting nvidia driver install and doing telinit 3
On hitting F2 I get these errors -
Code:
Is there anyway to boot in safe mode. I boot Fedora with GRUB2 and there isnt any failsafe entry for it. I have blacklisted nv driver already.
I installed nVidia by 1 click off suse site and on reboot my display is gone. I booted with failsafe Kernel. How do I get my display back with nVidia driver instead of default one.
View 9 Replies View RelatedWhen i start the install of the open suse linux 11.2 load the kernel but later my display is in black, i think that is my graphic card becouse in other linux only load linux without graphic mode, what i have to do for install open suse?, i can download a driver with the installer or something like?
View 4 Replies View RelatedI've manually installed the latest NVIDIA display drivers from the website (newer than the restricted driver package that came with 9.10). When there is a new Linux kernel, or a newer Ubuntu version, will I need to uninstall that driver before upgrading? Will having this driver cause any special installation issues during upgrade (such as the need to reinstall the driver after upgrading)? I am using 9.10 through Wubi.
View 1 Replies View RelatedPrior to updating suse was running slow. The desktop would act "weird" . It started after an update on 11.3. thought updating to 11.4 would fix everything. Last night Dled a copy of Suse 11.4 burned, checked for errors and did an update. Everything worked fine and booted to desktop. Nice shiny and new, was very happy for about a minute
Currently I get a terminal login screen when trying to boot Desktop, or failsafe ( network doesn't work on either of these 2). Xen will boot to desktop but toolbar is gone. Hit alt f2 to launch apps ( terminal, firefox, yast) and none show on screen. If I hit alt tab they show up in list.
With zen I hit CTRL+ALT+f2 and did zypper up thinking that would fix the problem. Updated successfully but same problem. Have a Nvidia 7950GTX so I selected zen, did ctrl-alt-f2 again. Launched yast, added the nvidia.com 11.4 repo and installed the 68xx newer driver. ran nvidia-xconfig and still it wouldn't boot to GUI. loaded zen again c-a-f2 - > yast found a second nvidia 68xxnewer driver, installed and now have 6 options to select at startup. 2 desktop, 2 failsafe, 2 xen.
Picked the first one and suse loaded. Yay. Ran nvidia settings to fix resolution, saved. Weird thing was only 2 of the desktops backgrounds would change, other 2 were white. Audio didn't work, usually a reboot fixes the problem so I rebooted and am back to none working except the xen login that gives me a crippled desktop ( can launch programs but none show up).
At first startup after update to 11.4 desktop backgrounds were changing really fast. Right clicked desktop went to click on desktop settings and that's when the tool bar down below disappeared ( it was working prior to that). That is when the desktop became crippled. Second tool bar at top from previous install is still there and can launch folders to open but none show on screen but show in alt - tab.
I just bought a new pc. It has plenty of hard drive space and ram with a 2.6GHz processor. I'm trying to run a dual-boot with Windows 7 and Linuxmint. I need some help as to how I go about installing my video driver. I have tried combinations of the following: -clicking on the taskbar icon that says "restricted drivers are available" and enabling the drivers -going to Software Manager/Drivers and choosing to install "NVidia 3D Drivers"
My efforts so far have only resulted in the following behavior: The screen changes from color into black-and-white and becomes unresponsive except to close it out The screen freezes up completely forcing me open up a terminal to kill the offending process (which turns out to be firefox)
The next thing I would like to try is to just go to the Nvidia website and downloading and installing the driver from there. It's a BIN file with a "run" extension. So I entered the command "chmod +x NVIDIA-Linux-x86-190.53-pkg1.run" followed by the command "./NVIDIA-Linux-x86-190.53-pkg1.run". But I get an error that says the following:
ERROR: You appear to be running an X server; please exit X before installing. WHAT IS AN X SERVER? HOW DO I CLOSE IT?? I've got nothing unusual open. Maybe a web page. I've tried closing out of everything except the terminal and I still get the same message.
I just got done installing Ubuntu on a new harddrive and set it up to dual boot with grub loader. However, when I boot into Ubuntu, the screen goes black. I can however login (blind) by hitting enter and typing password. The login sound goes and it logs in, however, the screen stays black. I am running a NVIDIA Quadro NVS 295 Video Card.
View 9 Replies View RelatedI have a video card. But I cannnot install nvidia driver because of some errors.
My video card's info is GeForce GTX760 1.5GB GDDR5.
Code: Select all$nvidia-detect
Detected NVIDIA GPUs:
01:00.0 VGA compatible controller [0300]: NVIDIA Corporation Device [10de:118e] (rev a1)
Uh oh. Your card is not supported by any driver version up to 304.125.
A newer driver may add support for your card.
Newer driver releases may be available in backports.
[CODE]
I am try to install the nvidia 96.43.16 driver for a Gforce 2 MX-400 video card following this [URL].. When I ran the 'rpm -e --nodeps xorg-x11-Mesa-libGL' command the the package wasn't installed.
When I ran modprobe nvidia it wasn't found either.
Being a newbe I had no idea what to do next.
I have an old video card, Nvidia XFX 7800GT, which is now beginning to fail and I need to upgrade. I am not huge a gamer but I do play/buy games on regular basis. Right now I'm playing Eternal Lands on the Linux side. Looking to spend $100-$150 on a new card.I have a Core2Duo Wolfdale 3.0, with 2ghz ram and run Lucid 32bit. Also run windows Vista64Ultimate on dual boot (rarely).
I would love to buy a new ATI 5770 or 5830, ATI budget cards seem to be much better for the buck over budget Nvidia cards, but I'm concerned with ATI drivers and long term with Ubuntu.On the Nvidia side I'm considering the GTS 250. The only advantage I can find is lower power consumption with Nvidia and Ubuntu has always preferred Nvidia over ATI, as far as working drivers go.As Far as Ubuntu and Lucid is concerned, which way is best, ATI or Nvidia? Has anything changed with ATI support, that could make theor cards more compatible now and in the future?
I was wondering if anyone else ran into and issue with 11.3 with an IBM x3650 server using the embedded graphics card. As a reference this exact machine was working under 11.2. I am aware that there were significant changed in how video works in 11.3.
While installing and during the initial start of the operating system I can see graphical output, OPEN SUSE logo and such.
During the boot process the screen goes blank. The server is still running and I am able to ssh to the machine, but there is no access to the console.
Below is a segment of the /var/log/boot.msg that shows some errors. I can provide more logs if that would assist in tracking this down.
I did a quick google search on ES1000 and i2c and saw the same errors reported with Ubuntu version but nothing for OPENSUSE. There seemed to be a bug that was fixed in that kernel.
<6>[ 2.277737] [drm] radeon: cp idle (0x00008080)
<6>[ 2.277767] [drm] Loading R100 Microcode
<6>[ 2.277770] platform radeon_cp.0: firmware: requesting radeon/R100_cp.bin
<6>[ 2.279454] [drm] radeon: ring at 0x00000000B0000000
<6>[ 2.279476] [drm] ring test succeeded in 1 usecs
code....
This is a new install and the machine is not yet in production so I have the option to experiment with it a bit.
I use a debian testing, I can't drive graphics card，open source driving performance is not good, so you need to closed source drive, model is nvidia 7300 gt, how to drive the video card?
View 5 Replies View RelatedI just installed Lucid Lynx RC 1 on my MSI Wind U100 netbook. When I tried to play a video on it I was informed of a lack of codecs, so I downloaded my video player of choice: VLC media player. When I tried to play the video, there was audio but the screen was black. The same thing happened when I downloaded to codecs and used the stock video application.
View 3 Replies View Related