Software :: Have To Unplug And Then Plug Back In Keyboard To Make It Work?
Oct 6, 2010
When I start X, my keyboard does not work. It seems like the wrong layout is being used. If I unplug it and then plug it back in then everything is good. I only have any Xkb options in xorg.conf.d. below is my keyboard config from xorg.conf.d. NOTE: I have /etc/X11/xorg.conf.d symlink'd to /usr/share/X11/xorg.conf.d, if that might be the cause of this problem
Code:
Section "InputClass"
Identifier "Apple USB Keyboard"
My problem here is the following: whenever I plug or unplug the AC cable in or out of my laptop it goes on hibernation, which is very annoying indeed. Sometimes I just want to plug it because I'm downloading something and my battery is running out.I would like to add that when my laptop goes into hibernation, and I try to bring it back up nothing happens, only the fans go on, but no activity other than that, at which point always just end up shutting the computer down cold and restarting it, which is getting to be a huge problem
I want to run a script when the switch goes down and an other when it goes up. Is there an easy way to pull this off in Debian (preferably with no other than system tools)? I suppose there is no difference (in the OS point of view) between unplugging ethernet cable and the switch losing power.
On an event I get lines like these in the syslog: Jun 15 17:49:41 debian kernel: [ 5506.956130] igb: eth1 NIC Link is Down ... Jun 15 17:49:45 debian kernel: [ 5511.168788] igb: eth1 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: RX/TX
In FreeBSD you can pipe log messages (pre-filtered by regex patterns) to a program. What is the easiest way to replicate this on Debian (with as little additional software as possible)?
Recently installed Ubuntu. It resurrected a dead machine. While using Miro, I went to a site in Firefox to check on a video downloads. The site said I couldn't play their files and gave me the option of downloading flash. Since Ubuntu was having trouble getting the dependancies together for me to load flash and make it work, I downloaded their offer. Now Miro doesn't recognize any of the available videos to download when I try to access them. How do I reverse the downloads?
I'm trying to net install Wheezy on an Abit IC7-G PIV system. I tried this months ago but the problem still exists. This is not so much an installation problem but after installation when it boots, I lose PS/2 mouse, PS/2 keyboard and network. I get:
startpar. service(s) returned failure udev ... failed I can plug USB mouse and keyboard in after this failure which then works. There is nothing wrong with the hardware. It works fine on other systems. Squeeze works perfectly.
I've bought this remote control that sais it works in Vista, XP etc. without any driver. Basically it has a bunch of buttons that replace the mouse and a bunch of others that replace basic keyboard functions (arrows, enter, escape). It has a USB IR receiver so I thought I could simply use it as a lirc remote in Ubuntu.
However, it sais absolutely nothing on it except for "PCremote" so during lirc installation I have no idea what to choose. And, interestingly, I accidentally discovered that it works in Ubuntu, too, out of the box. Controlling the mouse and acting like a keyboard. Is there a way I can forfeit current functionality and just get it to work as a customizable lirc remote? Or even better, keep current functionality but change it only for certain apps (xbmc, vlc etc)?
My server is Centos 5.3 I have php 5.1.6. some of plug-ins does not work I have to upgrade it to 5.2.6. To upgrade it I have to install a third party repositories.How can I protect my current php in case if the repository does not work I enable ( or role back) the Centos default php?
i have noticed that if vista is not the active partition, hybernate does not work. it just goes black and then back to the user icon screen to log back in. another "slight" problem was that i was not able to apply a service pack. after restoring vistas dominance i was able to install the pack. is there any other work arounds for hybernate? even though you might not be interested in cleaning up after microsoft.
first because of my nvidia card if I don't put nomodeset my screen turns off.also whenever I try to update my nvidia drivers either the ones from the ones from the website or the propriety drivers I get a MCU failure or something like that and to fix that i have to change "nvidia" in my xorg.conf to "nv" but then my resolution loads to 640x480 which i cant change and it says im not using the propriety drivers so then i changed "nv" to "vesa" which makes my screen highest screen resolution 1280x 720 and apparently my refresh rate is 0. but i cant do anything good without the propriety drivers.Also my sound doesn't work at all unless i plug in some headphones.
If I install a regular version of Ubuntu onto a USB drive using my desktop,can i plug the usb into my laptop and it will work normal,no issues having used the laptop desktop to install to the usb. Only reason asking because i can disable the harddrive on my laptop so i just unplug the harddrive in my desktop and install ubuntu like that onto usb,if theres a better method for laptop love to hear it
I just installed Linux(Ubuntu) and I when from Windows to Linux. I use the option to use the entire hard drive when it installed and my question is when I had it use the entire hard drive did it keep the computer drivers or did it erase them? I notice that the sound is only about have as loud as before but is that Linux or my computer? I also notice when I plug in my mp3 sometimes it doesn't detect it. Also when I plug in my headset into the font USB it doesn't work. I'm not sure what is going on.
Hi. I'm running the 64 bit OpenSuse 11.2 distro with Firefox 3.5.7 and the Novell mono plugin installed but still can't watch the olympics coverage on CTV.
This problem has been discussed a couple of times here and there and there are numerous solutions as well as unsolved stories. The topic says it all I think. I use ca(fr) layout, and in the gnome keyboard configuration (system, preferences, keyboard) I only leave Canada. When I log out and go back in, the layout changes to USA and in the configuration tool, theres canada AND usa. I have to delete USA every time. The file /etc/sysconfig/keyboard is already set to ca(fr) and doesn't change
I tried to delete: rm -f /var/cache/gdm/your-username/.dmrc rm -f ~/.dmrc
but I either did miss something or it didn't work. The only thing I observed is that if I set the keyboard layout to Ca(fr) at the login screen (which is always set back to USA), the layout stays to ca(fr) in my session. This problem did not occur on Fedora 11 and it began on 12 on my laptop as well as on my girlfriend's.
I've read somewhere and I forgot where, that it is a known bug in Gnome and that it is fixed in a later version. I applied all available updates and system/about this computer says I have Gnome 2.28.0 and if I recall, this bug is supposedly fixed in 2.28.4 but I may be wrong on the version number. This is very annoying as we try to turn our computers off when we don't use them but this reset every login kind of forces us to our previous bad habits.
I've got an UK keyboard, and every time I boot up, Ubuntu keep reverting back to the US keyboard layout which is annoying me. I open up keyboard preferences, the UK layout is already selected. So I delete the US layout, click on "Apply System-wide" and it works. Until I reboot and the US layout is back in there! I suspect it's something to do with not having admin privileges to permanently save the changes - if this is the case, why it doesn't ask me for my password, or give me a chance to escalate my privileges or something?
I have the ASUS G51JX A-1 laptop and I can not get the keyboard function keys to work at all. where to get the drivers.My main problem is with the back-lit keyboard, it detects it and always has the lights on which I do not want.I would like to be able to control it as well as the volume through the fn keys.
I have a Linux system running (Debian). It is working perfectly from a remote point of view. I can ssh in it, it has the imap running correctly, and a couple of kvm systems running (I can also ssh to them). Well, it works!
But when I go in front of the keyboard/mouse/screen there's nothing. No way to switch between the consoles with Ctrl+Alt+F# (X is not running on this system). The screen is desperately black. But the screen does not go to sleep mode, it still has its green led on! I guess it means that the graphics card still sends the H and V syncs correctly (VGA connection).
Is there a process that is blocking the display and prevents me from getting the control?
Note: Last time I used the console, it was in console 1. Ctrl+Alt+F1.
You have .exe files to install stuff. Even tho I have used ndiswrapper in the past I can't remember how now. I've got a nice old laptop with a nice install of SUSE 10 that does everything I want except connect to the internet. I've got about 1 more day of patience remaining before I have to revert to the hated Ws. I even got a supposed "plug and play" Asus usb-n10, but have not been able to work out the install.
yesterday I upgraded of my ubuntu release from 10.04 to 10.10 and now, when I plug my mp3 creative zen player it doesn't work.The same player works very well with 10.04 and I can upload my mp3s directly from rythmnbox using drag&drop.Here my /var/log/syslog
Code: Oct 20 15:58:20 tarini-laptop kernel: [25042.100344] hub 4-0:1.0: unable to enumerate USB device on port 2 Oct 20 15:58:38 tarini-laptop kernel: [25059.970030] usb 1-1: new high speed USB device using ehci_hcd and address 16 Oct 20 15:58:38 tarini-laptop kernel: [25060.102634] usb 1-1: device descriptor read/64, error -71[code].....
I have a DSL modem with four ports and a built-in wireless router downstairs. It works great: I have wired Ethernet for my PCs downstairs (all plugged in directly to the DSL modem); my son has great wireless access upstairs (using the built-in wireless in his laptop). PROBLEM: I want to add another, desktop, PC upstairs. I've been trying to use wireless, with a plug-in a Linksys USB stick. It doesn't work worth crap.
I'm considering a) getting another phone jack upstairs, and moving my DSL modem there, or b) stringing some CAT-5 cable from the modem downstairs to the PC upstairs. Putting a wireless PCI card in my upstairs desktop PC might also solve the problem, but the PC only has one PCI slot, and I'd rather keep it free, if at all possible.
QUESTION: Is there any kind of "wireless repeater", where I can a) get wireless access from my DSL modem/wireless base station downstairs, and b) give me some spare Ethernet ports, so I can plug in desktop PC (so the PC can have a wired Ethernet connection)? POSSIBLE SOLUTION: I have an old Linksys WRT54G router that I'm not using. Q: Is there any way to configure it for this purpose? Q: Would it be possible to use it for this purpose if I installed OpenWRT?
After some tests I found that some USB Bluetooth Dongles errors, only are recoverable if the USB is unplugged an then plugged again. Is there some way to simulate that a USB device is unplugged and re-plugged?
After an upgrade to 10.04, every time I unplug the AC adapter, the laptop crashes, and immediately shuts down and restarts, and will boot up normal, and shut down again as soon as it reaches the login screen.The laptop only runs fine when the cable is plugged in.I'm assuming this has something to do with the gnome power manager.I'm running an HP Pavilion dv4-2012la .
Dell XPS 420: Radeon HD 4670: Philips 720p TV monitor. When booting, after the GRUB screen nothing happens until the HDMI cable is unplugged and replugged. Various ATI drivers installed. Various /etc/X11/xorg.conf used.
i have been using ubuntu since last 3 months. in the mean time i had to reinstall it 3 times. every time i have to install and setup lot of things. is there any way to make a back up and if anything happens i can just recover?
I have an Asus Eee PC with Ubuntu Netbook Remix (Unity). The other day, I turned off the wireless using the keyboard shortcut to save battery life when I was somewhere without wireless, but now it's not turning back on. I tried restarting, I've done the keyboard shortcut several times, and it still just says "disconnected" for wireless and wired, even though there are several wireless networks around me right now. There aren't any options in Network Connections or Network Tools to turn on the wireless. Is there a way to manually turn it back on?
is it possible (and how) to create keyboard shortcut/binding that would give window-focus back to Tilda terminal? Currently, it is necessary to LMB-click inside Tilda (or at least drag mouse-cursor over Tilda) to resume typing.
