I just did a new install of slack 13.1 and i cant seem to be able to get my wireless card up. my system is a new ish dell laptop,a vostro 3700 to be honest im not even really sure where to start here. if i ifconfig i only get my ethernet and my loopback and if i "iwconfig" i just get told that i have no wireless extensions. yeah not sure what else to add.
View 4 Replieswhen it comes to openSUSE but I am earnestly trying. I installed the openSUSE OS on my HP dv6000 laptop, but it does not seem to recognize my wireless card (which is a Broadcom 4311).
View 7 Replies View Relatedi'm run'n knoppix 6.5 (i think) from a usb stick. under 'ifconfig' it finds 'eth0', but when i put in 'iwconfig eth0' it says: 'eth0 no wireless extensions'. i've tried other linux live cd's but to no avail...interestinly enough, when i run a linux (ubuntu) live cd on my virtual pc it hooks up(?..i figure bcuz its reading from da virtual ethernet?) further more, i researched it to the conclusion that the driver is not being detected. i tried ndiswrapper (under 'puppy') but tht didnt work either ( i've downloaded the lastes version of ndiswrapper and i plan on trying it again w/ the installation disk of the wireless card). however, even in my research i've seen there seem to be a difficulty in getting this particular driver to work? (netgear wg311v3 - wireless g pci adapter) how i can over come this problem? i'm kinda new @ linux, but i like the challenge. it doesnt matter wat linux system (the responder) i'll download it. but i'm really trying to get 1 online cuz i have to learn how to work the packaging systems.
View 4 Replies View RelatedHow do i get debian to recognize my wireless card? i have one built right into my laptop
after some messing around on the terminal i believe it is a code...
Do I need to install drivers or something to get it to recognize that my laptop is equipped with wireless? It's a Toshiba Satellite L505-S5990.
View 9 Replies View RelatedI can't get on the Internet at all not even through Ethernet. (It recognized my Ethernet hardware but doesn't connect.) I got the broadcom-wl drivers from Packman and installed those and it still was a no go. I tried to get the drivers straight from Broadcom and those didn't work. I couldn't compile the source code from the Brodcom site because i could not get build installed (got make installed but build just didn't install.)
Info:
Card
BCM4322
When I enter /sbin/lspci -nnk
Code:
00:00.0 Host bridge [0600]: Intel Corporation Mobile 4 Series Chipset Memory
[Code]....
Moving this to new topic, since it's no longer under wireless connectivity issues. [Noob Warning] I was having trouble getting Ubuntu to recognize my wireless card, as I have changed from the 3965 that came in my computer to the 4965, which added increased range and G band. Anyway, I read one of the threads on here, and this was the advice given:
Quote:
Originally Posted by pytheas22 First, download this file and save it to your desktop. Then run these commands:
Code:
sudo apt-get install build-essential
wget http://intellinuxwireless.org/iwlwifi/downloads/iwlwifi-5000-ucode-5.4.A.11.tar.gz
tar -xzvf iwlwifi*
sudo cp iwlwifi-5000-ucode-5.4.A.11/iwlwifi-5000-1.ucode /lib/firmware
bunzip2 compat-wireless-old
[Code]...
just installed ubuntu but it doesn't recognise my wireless card. I'm running an emachines g720. Ive tried looking through some previous posts but the terminal thing frightens me to death really.I've tried looking through the idiots guide but i'm afraid i'm a better idiot than that.
View 7 Replies View RelatedToday I deleted Windows on my Dell Latitude D610 and instead installed Ubuntu 10.04 on it (I had a cd with 10.04 on it from when I installed it on my desktop a year ago). Everything runs fine except I can't get the wifi to work, and it won't recognize the driver either, actually it doesn't recognize any drivers.
View 4 Replies View RelatedI had Karmic a while back, but i got rid of it becasue of my Bcm4312 Wireless Card would not recognize the STA driver, or bcm43xx.In that time i learned a bit of command line stuff. anyways now that I have my internet working, I was just wondering What I could do with ubuntu. I am interested in the command line and Programming. Where could I learn more about the 2 subjects?
View 6 Replies View RelatedJust put Ubuntu 10.10 on my Fujitsu Amilo Li1818 and it does not seem to recognise the wireless card. If I click on the network icon in the top bar there is no mention of wireless.
View 1 Replies View RelatedI am running openSuse 11.1 64 bit on my hp pavilion dv6458se; and am unable to get my Broadcom wireless card to work.
i tried reading a few forums, but they all start when 'lspci' recognizes the card.
My problem is that 'lspci' does not show any 'Broadcom' card.
I have given below the output of 'lspci' for your reference.
my cisco wireless card model # wmp600n. Fedora doesn't even recognize that its there and i haven't been able to find any linux drivers for it, tried installing the driver using wine but still isnt working for me...
View 2 Replies View RelatedIm not to good with manually making anything work on linux and was wondering if ubuntu will automatically recognize my wireless 1395 mini card...
View 2 Replies View RelatedI have a problem with my Grundig's (model GNB-250D) laptop wireless card. I recently installed Ubuntu 10.10 and tried to use a wireless connection to browse the internet but it didn't detect any, it seemed strange as it worked perfectly on Windows. I can browse the internet fine if I use an Ehternet cable.
View 4 Replies View RelatedI installed Kubuntu 9.10 using wubi (dualboot with Windows 7). There were no network connections available, even though I have two that can be used when I switch to Windows. After two hours I got tired of trying to fix the problem and rebooting to no avail, so i uninstalled and installed Ubuntu instead. I've still got the same problem, and after hitting a hole in my wall and shaving my head, I have no idea how to fix the problem. How do i get Ubuntu to recognize my wireless network?
View 9 Replies View Related1 ) make and model of wireless device Athreos 5k
2 ) driver version in use dont know
3 ) any error message. -
abhishek:/ # sudo /usr/sbin/iwlist scan
lo Interface doesn't support scanning.
eth0 Interface doesn't support scanning.
wlan0 Interface doesn't support scanning : Network is down
4 ) what you have tried to rectify the problem.
Tried to install all the patches.
5 ) any trouble-shooting guide you have tried to follow. - The previous two stickies
6 ) openSUSE version 11.3
7 ) type /sbin/lspci -v" in a terminal; copy and paste the section that identifies your wireless card and it's chipset. 07:00.0 Ethernet controller: Atheros Communications Inc. AR5001 Wireless Network Adapter (rev 01)
Subsystem: Hewlett-Packard Company Device 137a
Flags: bus master, fast devsel, latency 0, IRQ 23
Memory at c2000000 (64-bit, non-prefetchable) [size=64K]
[code]....
My computer is ThinkPad SL400 and the wireless card is AR5001 wireless network adapter (Atheros Communications Inc.). I now use slackware13.37. I can't make the wireless card work and the indicator light is always out. In Windows7, the wireless card can work. Doesn't the kernel 2.6.37 support ath5k? I find the webpage [URL], but I don't know whether I should download the relevant driver or the kernel has already possessed the driver and the only thing to do is activate it.
View 4 Replies View Relatedmy name is jackson and I use the slackware 13, I am learning now, and I have a problem with my wireless conection, I dont get to active my wireless card what I can do to active my wireless function in slackware 13 with lspci comannd I can see is a broadcom wireless controller but I don�t get to active
View 3 Replies View RelatedI have been waiting on installing ubuntu on my mid 2010 MBP 15' for a while now. I was wondering if the dynamic GPU switching was supported yet. Does Ubuntu recognize the intel card and can I use it over the nVidia card?
View 1 Replies View RelatedI have an older laptop (Dell Inspiron 4100) on which I have installed a minimal Slackware system, and have just managed to get wireless working by using a Linksys Wireless-G card (WPC54GS) and installing the b43 packages from the SlackBuilds site.
Unfortunately, I am experiencing system freezes ... and if my Google searches are correct, these are related to the firmware driver (b43 stuff).
I wonder if anyone can recommend a good wireless card that works with Slackware out of the box ?
After doing a reconfigure of my wrt54gl router, trying to activate WEP encryption, and then finding WICD wouldn't connect, and returning to the original config on the router, now wicd won't reconnect the wireless card. Here's the wicd.log entry from the attempt to connect:
Code:
2010/01/30 18:40:46 :: ifconfig wlan0 up
2010/01/30 18:40:46 :: iwlist wlan0 scan
2010/01/30 18:40:47 :: ifconfig eth0
2010/01/30 18:40:47 ::
2010/01/30 18:40:47 :: {}
2010/01/30 18:40:47 :: hidden
2010/01/30 18:40:48 :: scanning done
2010/01/30 18:40:48 :: found 4 networks:
2010/01/30 18:40:48 :: found use_settings_globally in configuration 1
2010/01/30 18:40:48 :: found afterscript in configuration None .....
Hi I have istalled a D-Link wireless adaptor - with the help of this forum.
It is up and running - the light flashes and lsusb identifies it correctly, so does iwconfig.
I can, however, not connect to the network, and I noticed the following errors on boot up.
Trigering udev events: /sbin/udevadm trigger -- type: failed /etc/rc.d/rc.M: wlan0 Error for wireless request; "Set Nickname" (8BIC) information; "Any ESSID" Set failed on device wlan0; operation not supported.
Lower down I get
Starting rt2870 drivers . . . /etc/rc.d/rc.inet1: wlan0 information "Any ESSID"
Error for wireless request "Set Nickname" (8BIC) set failed on device wlan0 : Operation not supported
I have on two occassions seen sugstions to use wicd, but how do I use that?
i'm running slack 13.37. my machine has a "generic" wireless card which is currently sitting idle in it, since i used a wired interface for internet and local networking (i used the wireless interface for a while, but for what i need it wasn't a reliable or stable enough connection). my question is, can the idle card be used as a wireless access point on a separate subnet? if so how?
View 1 Replies View RelatedI have changed kernel to 2.6.33. After that ifconfig command shows only my ethernet card, wireless card have disappeared. What is wrong. In the old kernel everything works fine. I am sure that i have installed wi-fi stuff with kernel.
View 14 Replies View RelatedI have installed Ubuntu via USB on a Dell Inspiron E1505 and I am unable to turn on the wireless card. I have a dual boot with Windows XP and I am able to turn on the card with keystroke Function/F2 and it works while in Windows. When I reboot in Ubuntu I am not able to use these keystrokes to turn on the card.
View 4 Replies View RelatedI just installed Slackware 13 with xfce and everything went well (eventually). At first, my wireless didn't work, but then I found /etc/rc.d/rc.wireless.conf. Everything was working, and I was happily surfing and downloading packages.But then one day... It just stopped! I tried to ping google, and it could send packets but not receive them.I'm connecting through an unlocked network in my building, so I guess it's DHCP (thats what i set it up with the first time 'round
View 1 Replies View RelatedI'm currently installing Slackware 13.1 on my old Sony VAIO. It's got a wireless card sticking out the side of it, and I just want to make sure I set it all up correctly. I got to the screen where it's asking:
static IP
DHCP
loopback
And I'm not sure which one to pick.
I have for 2 months Toshiba Satellite A 500-18Q (Core Duo, Windows7 pre-installed). I have just wifi internet in my home, with Windows7 it works perfectly and automatic. However, my fresh- installed Fedora12 cannot see any wifi at all. I my NetworkManager I can see a single line with "eth0" which seems to refer to a normal (cable) connection. How to activate wifi? Just add a new line with eth1 and Wireless connection? Or I need to install some drivers?
this is output from my terminal:
# lspci
01:00.1 Audio device: nVidia Corporation Device 0be2 (rev a1)
0e:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168B PCI Express Gigabit Ethernet controller (rev 03)
[code].....
I have been running F13 since it came out, with the wireless working fine since I got it working (using the RPM Fusion repository, broadcom-wl-5.60.48.36-1.fc13). Since I updated software (without reading what was to be updated), yesterday, I am unable to even find wireless networks, although I am, as you can see, able to access through eth0 It is not a hardware problem, as I can not only find them, but access them on Ubuntu 9.10 live disc. Below is my lspci
00:00.0 Host bridge: Intel Corporation Mobile 4 Series Chipset Memory Controller Hub (rev 07)
00:02.0 VGA compatible controller: Intel Corporation Mobile 4 Series Chipset Integrated Graphics Controller (rev 07)
00:02.1 Display controller: Intel Corporation Mobile 4 Series Chipset Integrated Graphics Controller (rev 07)
[code].....